The WM8995 is a digital audio hub CODEC designed for smartphones.
The current driver supports most of the basic functionality of the
WM8995.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

snd_soc_jack_new()'s first parameter was changed from snd_soc_card to
snd_soc_codec after Multi-Component support patches. So, this patch
fixes parameter that we missed.
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

Add jack detection interrupt trace to Wolfson CODEC drivers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

This avoids blocking the IRQ thread and allows further bounces to extend
the debounce time.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

FSI-AK4642 and FSI-DA7210 are depend on I2C, not I2C_SH_MOBILE
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Make LZO cache compression optional as it pulls in the kernel wide LZO
implementation and rbtree compression is generally more efficient for
typical register maps, especially in terms of CPU performance.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

This makes it easier to make cache types build time configurable as we
don't have a hard dependency on a given cache being built in.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

Cut'n'paste in the register names.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

These would have been used if we'd done manual clock divider setup,
but we didn't.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

Add ASoC machine driver for SMDKV310/C210 boards that have
a WM8994 attached to I2S-0.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Enable AC97 audio device on SMDKV310/C210.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Since most newer SMDKs have I2S0 routed to the WM8580's Primary DAI,
future changes can be minimized if the default CPU DAIs are set to
0, rather than 2.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Flush the FIFO while stopping the channel rather than starting.
This saves time during stream start and keeps the FIFOs clean
when the channel is idling.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Since the rclk_srcrate is cleared upon startup, it should be
initialized upon second and later 'open' calls to the device
with same root-clock source. The bug is otherwise visible in
Codec-Slave mode.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Merge branch 'topic/asoc' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6 into for-2.6.38

This new type is a virtual version of snd_soc_dapm_mux.  It is used
when a backing register value is not necessary for deciding which
input path to connect.  A simple virtual enumeration control e.g.
SOC_DAPM_ENUM_VIRT() can be exposed to userspace which will be used
to choose which path to connect.

The snd_soc_dapm_virt_mux type ensures that during the initial
path setup, the first (which is also the default) input path will
be connected.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Merge branch 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/asoc-2.6 into topic/asoc

Current FSI driver had printed under/over run error
if status register have its error bit.
But runtime print cause the next error
because print out is slow.
This patch add error counter and print error when sound stop
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Attempt to minimise audible effects from mixer and mux updates by
implementing the actual register changes between powering down widgets
that have become unused and powering up widgets that are newly used.

This means that we're making the change with the minimum set of widgets
powered, that the input path is connected when we're powering up widgets
(so things like DC offset correction can run with their signal active)
and that we bring things down to cold before switching away.  Since
hardware tends to be designed for the power on/off case more than for
dynamic reconfiguration this should minimise pops and clicks during
reconfiguration while active.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

Add ramp functions for the headset and handsfree outputs
in order to reduce the pops during power on/off sequences.

In order to give more control to volume ramp, step size and delay
between steps can be specified.

The patches are based on wm8350 implementation from Liam
Girdwood.
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Updated default values to improve power consumption.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Power change event like stream start/stop or kcontrol change in a
cross-device path originates from one device but codec bias and widget power
changes must be populated to another devices on that path as well.

This patch modifies the dapm_power_widgets so that all the widgets on a
sound card are checked for a power change, not just those that are specific
to originating device. Also bias management is extended to check all the
devices. Only exception in bias management are widgetless codecs whose bias
state is changed only if power change is originating from that context.

DAPM context test is added to dapm_seq_run to take care of if power sequence
extends to an another device which requires separate register writes.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Decoupling widgets from DAPM context is required when extending the ASoC
core to cross-device paths. Even the list of widgets are now kept in
struct snd_soc_card, the widget listing in sysfs and debugs remain sorted
per device.

This patch makes possible to build cross-device paths but does not extend
yet the DAPM to handle codec bias and widget power changes of an another
device.

Cross-device paths are registered by listing the widgets from device A in
a map for device B. In case of conflicting widget names between the devices,
a uniform name prefix is needed to separate them. See commit ead9b919
"ASoC: Add optional name_prefix for kcontrol, widget and route names" for
help.

An example below shows a path that connects MONO out of A into Line In of B:

static const struct snd_soc_dapm_route mapA[] = {
	{"MONO", NULL, "DAC"},
};

static const struct snd_soc_dapm_route mapB[] = {
	{"Line In", NULL, "MONO"},
};
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Decoupling DAPM paths from DAPM context is a first prerequisite when
extending ASoC core to cross-device paths. This patch is almost a nullop and
does not allow to construct cross-device setup but the path clean-up part in
dapm_free_widgets is prepared to remove cross-device paths between a device
being removed and others.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

There are no users of these and it's not clear what they would do given
the mono flow modelling which DAPM does. If need arises we can add them
again.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>

Gain for LineInAmp Right uses LINEGAIN[5:3], which means that
offset for right channel should be 4.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Some gains were incorrectly configured for dB values.
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

After coming back from suspend, the timeout waiting for Phoenix
chip to complete its power up sequence is not enough, which leaves
the codec cache value for some registers in an outdated state.

Increase the timeout value to wait for the power up sequence
to correclty complete.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Enable plug detection interrupt mask in order to get headset
PLUGINT/UNPLUGINT interrupts.
Signed-off-by: Misael Lopez Cruz <misael.lopez@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

On Phoenix 1.1, the INTID register default value is an invalid
one, causing the interrupt handler to think the phoenix power on
sequence is ready before it actually finishes.

This causes some i2c errors when trying to configure twl.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

Phoenix 1.1 supports automatic power on sequence, a
verification is added to use it with new revision of
the chip.
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

The mux control has 4 elements not 3
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>

The twl6040 can support more sample rates other than 88.2 and 96k.
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>