This patch adds a structure usb_otg_caps to cover all otg related
capabilities of the device, including otg revision, and if hnp/srp/adp
is supported.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Add USB_OTG_ADP definition for usb_otg_descriptor.bmAttributes.
Signed-off-by: Macpaul Lin <macpaul@gmail.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

OTG 2.0 introduces bcdOTG in otg descriptor to identify the OTG and EH
supplement release number with which the OTG device is compliant, this
patch adds structure usb_otg20_descriptor for OTG 2.0 and above.
Signed-off-by: Macpaul Lin <macpaul@gmail.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The A33 SoC uses the same musb controller as found on the A31 and later,
but allwinner has removed the configdata register, this commit adds special
handling for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

The A31 SoC uses the same musb controller as found in earlier SoCs, but it
is hooked up slightly different. Its SRAM is private and no longer controlled
through the SRAM controller, and its reset is controlled via a separate
reset controller. This commit adds support for this setup.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This is based on initial code to get the Allwinner sunxi musb controller
supported by Chen-Yu Tsai and Roman Byshko.

This adds support for the Allwinner sunxi musb controller in both host only
and otg mode. Peripheral only mode is not supported, as no boards use that.

This has been tested on a cubietruck (A20 SoC) and an UTOO P66 tablet
(A13 SoC) with a variety of devices in host mode and with the g_serial gadget
driver in peripheral mode, plugging otg / host cables in/out a lot of times
in all possible imaginable plug orders.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Use bind_deactivated flag instead of calling usb_function_deactivate()
in function bind(). Field 'can_activate' in struct f_obex is no longer
needed as setting 'bind_deactivated' flag makes us sure, that the function
will be binded only if deactivation can be performed successfully.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Use bind_deactivated flag instead of calling usb_function_deactivate()
in function bind().
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch introduces 'bind_deactivated' flag in struct usb_function.
Functions which don't want to be activated automatically after bind should
set this flag, and when they start to be ready to work they should call
usb_function_activate().

When USB function sets 'bind_deactivated' flag, initial deactivation
counter is incremented automatically, so there is no need to call
usb_function_deactivate() in function bind.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Using usb_gadget_disconnect to make gadget temporarily invisible to host
doesn't provide desired result, because gadget is connected immediately
after binding regardless to previous usb_gadget_disconnect() calls.

For this reason we use usb_gadget_deactivate() instead of
usb_gadget_disconnect() to make it working as expected.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

These functions allows to deactivate gadget to make it not visible to
host and make it active again when gadget driver is finally ready.

They are needed to fix usb_function_activate() and usb_function_deactivate()
functions which currently are not working as usb_gadget_connect() is
called immediately after function bind regardless to previous calls of
usb_gadget_disconnect() function.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Driver handles PHY initialization, clock management, power
management and workarounds required after resetting the hardware.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Mass storage spec allows up to 16 LUNs, so let's not
add some more restrictive limits.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

EXPORT_SYMBOL_GPL() is usually placed after function definition
not before.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Creation of LUN 0 may fail (for example due to ENOMEM).
As fsg_common_set_num_buffers() does some memory allocation
we should free it before it becomes unavailable.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

We should only change endpoint names when we
actually manage to enable/disable it.
Signed-off-by: Felipe Balbi <balbi@ti.com>

We have a "Enabling %s" trace when enabling an endpoint
but that message felt lonely without a matching
"Disabling %s". Add it.
Signed-off-by: Felipe Balbi <balbi@ti.com>

When a SoC supports both PHY interfaces but
doesn't define HSPHY in DT/pdata, we will get
an unnecessary dev_warn() which can mislead users
into thinking that they're missing something.

Instead, let's just silently rely on a correct
default. If the HW default is wrong, then HSPHY
is required and USB won't work, this will be
motivation enough for engineers to patch their
way into a working setup.
Reported-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Since 39b2bbe3 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.

Currently this parameter is made optional with the help of a cpp trick.
To allow dropping this hack convert callers to explictly pass a value
for flags.
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Since 39b2bbe3 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.

Use this additional parameter and the _optional variant to simplify the
driver and improve error handling. Also expand the comment to explain
why it's not sensible to switch to devm_gpiod_get and why the gpiod_put
is also necessary.

Furthermore this is one caller less that stops us making the flags
argument to gpiod_get*() mandatory.
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch removes the deprecated notifier API of extcon framwork
and then use the new extcon API with the unique id to indicate
the each external connector (USB, USB-HOST).

Alter deprecated API as following:
- extcon_register_interest() -> extcon_register_notifier()
- extcon_get_cable_state(*edev, char *) -> extcon_get_cable_state_(*edev, id)

Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch removes the deprecated API of extcon and then use the new extcon API
with the unique id to indicate the each external connector (USB-HOST).
- extcon_get_cable_state(*edev, char *) -> extcon_get_cable_state_(*edev, id)

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Peter Chen <peter.chen@freescale.com>
Cc: Varka Bhadram <varkab@cdac.in>
Cc: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch uses the devm_extcon_dev_[allocate|register]() to manage the
resource automatically and replace deprecated API as following:
- extcon_[set|get]_cable_state(*edev, char *) -> extcon_[set|get]_cable_state_(*edev, id)

Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch removes the deprecated notifier API of extcon framwork
and then use the new extcon API with the unique id to indicate
the each external connector (USB, USB-HOST).

Alter deprecated API as following:
- extcon_register_interest() -> extcon_register_notifier()
- extcon_get_cable_state(*edev, char *) -> extcon_get_cable_state_(*edev, id)

[ balbi@ti.com : fix build break ]

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch removes the deprecated notifier API of extcon framwork
and then use the new extcon API with the unique id to indicate
the each external connector (USB, USB-HOST).

Alter deprecated API as following:
- extcon_register_interest() -> extcon_register_notifier()
- extcon_get_cable_state(*edev, char *) -> extcon_get_cable_state_(*edev, id)

Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

In big endian cases, the macro cpu_to_le{16,32} unfolds to __swab{16,32}
which provides special case for constants. In little endian cases,
__constant_cpu_to_le{16,32} and cpu_to_le{16,32} expand directly to
the same expression. So, replace __constant_cpu_to_le{16,32} with
cpu_to_le{16,32} with the goal of getting rid of the definition of
__constant_cpu_to_le{16,32} completely.

The semantic patch that performs this transformation is as follows:

@@expression x;@@

(
- __constant_cpu_to_le16(x)
+ cpu_to_le16(x)
|
- __constant_cpu_to_le32(x)
+ cpu_to_le32(x)
)
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

I18N should be spelled as i18n because it's not
an acronym
Signed-off-by: Diego Viola <diego.viola@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

In big endian cases, macro cpu_to_le16 unfolds to __swab16 which
provides special case for constants. In little endian cases,
__constant_cpu_to_le16 and cpu_to_le16 expand directly to the
same expression. So, replace __constant_cpu_to_le16 with
cpu_to_le16 with the goal of getting rid of the definition of
__constant_cpu_to_le16 completely.

The semantic patch that performs this transformation is as follows:

@@expression x;@@

- __constant_cpu_to_le16(x)
+ cpu_to_le16(x)
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

As SourceSink function has been reworked for ConfigFS
composite gadget this comment is no longer valid.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

As loopback function has been reworked for ConfigFS
composite gadget this comment is no longer valid.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

now that we have no users of dev_dbg() in dwc3,
we can safely remove CONFIG_USB_DWC3_DEBUG.

If dev_dbg() is ever strictly necessary - and I
don't see why it would, considering we want to
rely on tracepoints for debug - we will depend
on DYNAMIC_PRINTK to enable such messages.
Signed-off-by: Felipe Balbi <balbi@ti.com>

the mode of operation is exposed through debugfs
at all times. Because of that, we're removing
the unnecessary messages.
Signed-off-by: Felipe Balbi <balbi@ti.com>

those two messages are informing that the clock
doesn't exist; that, however, is a valid situation
and driver continues just fine by ignoring the error.
Reviewed-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>

that message is informing that the clock is missing.
However, that's a valid condition for some setups; driver
even ignores the error and continues just fine.
Signed-off-by: Felipe Balbi <balbi@ti.com>

that's an error condition, not a debugging message.

Let's promote it appropriately.
Signed-off-by: Felipe Balbi <balbi@ti.com>

Some of the messages were plain unnecessary
and some were actually errors. Fix it all
up.
Signed-off-by: Felipe Balbi <balbi@ti.com>

It's just a lot clearer to use | operator instead of
+ operator.

Caught by coccicheck:

	"
	drivers/usb/dwc2/gadget.c:2883:26-27: WARNING: sum of probable
	bitmasks, consider |
	"

Cc: John Youn <John.Youn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch adds removable mass storage support to g_nokia gadget (for N900).
It means that at runtime block device can be exported or unexported.
So it does not export anything by default and thus allows to use MyDocs
partition as before...

[ balbi@ti.com: make it build ]
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Pull perf fix from Thomas Gleixner:
 "A single fix for the intel cqm perf facility to prevent IPIs from
  interrupt context"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/intel/cqm: Return cached counter value from IRQ context