Change default to RTS/CTS protection. This has a cost of transmitting
one more control frame (RTS) however protect us from traffic from
hidden node.

On station mode will use CTS-to-self if AP will configure that
for the network.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Those TX_SW_CFG1 values are used in vendor driver.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Initialize AUTO_RSP_CFG register to similar value as vendor driver does.

Do not set BAC_ACK_POLICY based on short preamble setting, those are
unrelated.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

We already initlized WPDMA_GLO_CFG_WP_DMA_BURST_SIZE to 3 on
rt2800_init_registers() for USB devices. For PCI devices we will use
HW default setting, which is 2, so patch does not change behaviour
on PCI devices.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

We should not reset USB_DMA_CFG on rt2800usb_init_registers() as this
function is called indirectly from rt2800_enable_radio(). If we
do so, we wipe out USB_DMA_CFG settings from rt2800usb_enable_radio().
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

We should only set IEEE80211_HT_MCS_TX_RX_DIF when TX and RX MCS sets
are not equal, i.e. when number of tx streams is different than
number of RX streams.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Firmware doesn't update beacon/Probe Response vendor IEs correctly when
bss is down, so we move brcmf_config_ap_mgmt_ie after BSS up. And host
driver should clear IEs when AP stopped so that the IEs in host side will
be synced with in firmware side.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In device removal routine, usage of "#ifdef CONFIG_RT2X00_LIB_USB"
will not cover the case when it is configured as module. This will
omit the entire if-block which does cleanup of URBs and cancellation
of pending work. Changing the #ifdef to #if IS_ENABLED() to fix it.
Signed-off-by: Vishal Thanki <vishalthanki@gmail.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ath.git patches for 4.10. Major changes:

ath9k

* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
  latency and fix bufferbloat

It should never be NULL here, and to think otherwise makes things
confusing.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

These are never NULL, so stop making people think they might be.

I don't change this for SDIO because SDIO has a racy card-reset handler
that reallocates this struct. I'd rather not touch that mess right now.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Tested-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

sdio_func is retrieved via container_of() and should never be NULL.
Checking for NULL just makes the logic more confusing than necessary.
Stop doing that.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Tested-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

SDIO and PCIe drivers handle this. Let's imitate it.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Tested-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

card->adapter gets initialized in mwifiex_register_dev(). As it's not
cleared in mwifiex_unregister_dev(), we may end up accessing the memory
which is already free in below scenario.

Scenario: Driver initialization is failed due to incorrect firmware or
some other reason. Meanwhile device reboot/unload occurs.

This is safe, now that we've properly synchronized suspend() and
remove() with the FW initialization thread; now that code can simply
check for 'card->adapter == NULL' and exit safely.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Tested-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Signed-off-by: Brian Norris <briannorris@chromium.org>
Tested-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The device core will not allow suspend() to race with remove().
Signed-off-by: Brian Norris <briannorris@chromium.org>
Tested-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

to_pci_dev() would just do struct offset arithmetic on struct
device to get 'pdev' pointer. We never get NULL pdev pointer.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Tested-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

It's possible for the FW init sequence to fail, which will trigger a
device cleanup sequence in mwifiex_fw_dpc(). This sequence can race with
device suspend() or remove() (e.g., reboot or unbind), and can trigger
use-after-free issues. Currently, this driver attempts (poorly) to
synchronize remove() using a semaphore, but it doesn't protect some of
the critical sections properly. Particularly, we grab a pointer to the
adapter struct (card->adapter) without checking if it's being freed or
not. We later do a NULL check on the adapter, but that doesn't work if
the adapter was freed.

Also note that the PCIe interface driver doesn't ever set card->adapter
to NULL, so even if we get the synchronization right, we still might try
to redo the cleanup in ->remove(), even if the FW init failure sequence
already did it.

This patch replaces the static semaphore with a per-device completion
struct, and uses that completion to synchronize the remove() thread with
the mwifiex_fw_dpc(). A future patch will utilize this completion to
synchronize the suspend() thread as well.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Power save handshake with firmware might be blocked by on-going
data transfer.
this patch check the PS status in main process and complete
previous blocked PS handshake.
this patch also remove redudant check before call
mwifiex_check_ps_cond function.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Shengzhen Li <szli@marvell.com>
Tested-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

We may get SLEEP event from firmware even if TXDone interrupt
for last Tx packet is still pending. In this case, we may
end up accessing PCIe memory for handling TXDone after power
save handshake is completed. This causes kernel crash with
external abort.

This patch will only allow downloading sleep confirm
when no tx done interrupt is pending in the hardware.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Shengzhen Li <szli@marvell.com>
Tested-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Commit ce4f6f0c ("mwifiex: add platform specific wakeup interrupt
support") added WoWLAN feature only for sdio. This patch moves that
code to the common module so that all the interface drivers can use
it for free. It enables pcie and sdio for its use currently.
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Introduce function mwifiex_probe_of() to parse common properties.
Interface drivers get to decide whether or not the device tree node
was a valid one (depending on the compatible property),
Lets fill "adapter->dt_node" in mwifiex_add_card().

The function mwifiex_probe_of() is currently only a place holder with
the next patch adding content to it.
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Today all the interface drivers (usb/pcie/sdio) assign the
adapter->dev in the register_dev() callback, although they
have this piece of info well before hand.

This patch makes the device structure available for mwifiex
right at the beginning, so that it can be used for early
initialization if needed.

This is needed for subsequent patches in this patchset that
intend to unify and consolidate some of the code that would
otherwise have to be duplicated among the interface drivers
(sdio, pcie, usb).
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch derives device tree node from pcie bus layer framework.
Device tree bindings file has been renamed(marvell-sd8xxx.txt ->
marvell-8xxx.txt) to accommodate PCIe changes.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Rajat Jain <rajatja@google.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The cleanup_if() callback is the inverse of init_if(). We allocate our
'card' interface structure in the probe() function, but we free it in
cleanup_if(). That gives a few problems:
(a) we leak this memory if probe() fails before we reach init_if()
(b) we can't safely utilize 'card' after cleanup_if() -- namely, in
    remove() or suspend(), both of which might race with the cleanup
    paths in our asynchronous FW initialization path

Solution: just use devm_kzalloc(), which will free this structure
properly when the device is removed -- and drop the set_drvdata(...,
NULL), since the driver core does this for us. This also removes the
temptation to use drvdata == NULL as a hack for checking if the device
has been "cleaned up."

I *do* leave the set_drvdata(..., NULL) for the hacky SDIO
mwifiex_recreate_adapter(), since the device core won't be able to clear
that one for us.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Firmware may reject calibration data from host for certain OTP
settings. In that case, we should continue initialisation ignoring
the failure.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch adds power save parameters(hs_wake_interval and
hs_inactivity_timeout) in host sleep cfg cmd.
Signed-off-by: Shengzhen Li <szli@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

kmemleak reports memory leak in mwifiex_save_hidden_ssid_channels():

unreferenced object 0xffffffc0a2914780 (size 192):
  comm "ksdioirqd/mmc2", pid 2004, jiffies 4307182506 (age 820.684s)
  hex dump (first 32 bytes):
    00 06 47 49 4e 2d 32 67 01 03 c8 60 6c 03 01 40  ..GIN-2g...`l..@
    07 10 54 57 20 34 04 1e 64 05 24 84 03 24 95 04  ..TW 4..d.$..$..
  backtrace:
    [<ffffffc0003375f4>] create_object+0x164/0x2b4
    [<ffffffc0008e3530>] kmemleak_alloc+0x50/0x88
    [<ffffffc000335120>] __kmalloc_track_caller+0x1bc/0x264
    [<ffffffc00030899c>] kmemdup+0x38/0x64
    [<ffffffbffc2311cc>] mwifiex_fill_new_bss_desc+0x3c/0x130 [mwifiex]
    [<ffffffbffc22ee9c>] mwifiex_save_curr_bcn+0x4ec/0x640 [mwifiex]
    [<ffffffbffc22f45c>] mwifiex_handle_event_ext_scan_report+0x1d4/0x268 [mwifiex]
    [<ffffffbffc2375d0>] mwifiex_process_sta_event+0x378/0x898 [mwifiex]
    [<ffffffbffc224dc8>] mwifiex_process_event+0x1a8/0x1e8 [mwifiex]
    [<ffffffbffc2228f0>] mwifiex_main_process+0x258/0x534 [mwifiex]
    [<ffffffbffc258858>] 0xffffffbffc258858
    [<ffffffc00071ee90>] process_sdio_pending_irqs+0xf8/0x160
    [<ffffffc00071efdc>] sdio_irq_thread+0x9c/0x1a4
    [<ffffffc000240d08>] kthread+0xf4/0x100
    [<ffffffc0002043fc>] ret_from_fork+0xc/0x50
    [<ffffffffffffffff>] 0xffffffffffffffff
Signed-off-by: Ricky Liang <jcliang@chromium.org>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

When there is a CRC error in the SPROM read from the device, the code
attempts to handle a fallback SPROM. When this also fails, the driver
returns zero rather than an error code.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled, spin_lock_irqsave()
make sure always in irq disable context. So the kfree_skb()
should be replaced with dev_kfree_skb_irq().

This is detected by Coccinelle semantic patch.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

On x86, the cw1200 driver produces a rather silly warning about the
possible use of the 'ret' variable without an initialization
presumably after being confused by the architecture specific definition
of WARN_ON:

drivers/net/wireless/st/cw1200/wsm.c: In function ‘wsm_handle_rx’:
drivers/net/wireless/st/cw1200/wsm.c:1457:9: error: ‘ret’ may be used uninitialized in this function [-Werror=maybe-uninitialized]

We have already checked that 'count' is larger than 0 here, so
we know that 'ret' is initialized. Changing the 'for' loop
into do/while also makes this clear to the compiler.
Suggested-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The hostap_80211_rx() function is supposed to set up the mac addresses
for four possible cases, based on two bits of input data. For
some reason, gcc decides that it's possible that none of the these
four cases apply and the addresses remain uninitialized:

drivers/net/wireless/intersil/hostap/hostap_80211_rx.c: In function ‘hostap_80211_rx’:
arch/x86/include/asm/string_32.h:77:14: warning: ‘src’ may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/net/wireless/intel/ipw2x00/libipw_rx.c: In function ‘libipw_rx’:
arch/x86/include/asm/string_32.h:77:14: error: ‘dst’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
arch/x86/include/asm/string_32.h:78:22: error: ‘*((void *)&dst+4)’ may be used uninitialized in this function [-Werror=maybe-uninitialized]

This warning is clearly nonsense, but changing the last case into
'default' makes it obvious to the compiler too, which avoids the
warning and probably leads to better object code too.

The same code is duplicated several times in the kernel, so this
patch uses the same workaround for all copies. The exact configuration
was hit only very rarely in randconfig builds and I only saw it
in three drivers, but I assume that all of them are potentially
affected, and it's better to keep the code consistent.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

gcc 7 complains:
drivers/net/wireless/intersil/p54/fwio.c: In function 'p54_scan':
drivers/net/wireless/intersil/p54/fwio.c:491:4: warning: 'memset' used with length equal to number of elements without multiplication by element size [-Wmemset-elt-size]

Fix that by passing the correct size to memset.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This simplifies debugging. Format %s (%u) comes from similar debugging
message in brcmf_fweh_event_worker.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

* Command frame vap_capabilites is modified to use for vap add, vap delete
  and vap update in firmware, hence new filed vap status is added.
* When interface is down this frame needs to be send with vap status delete.
  Otherwise it is considered as wrong frame for the same interface in firmware.
* vap_update status is reserved for future.
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Observed crash when module is unloaded if CONFIG_RSI_DEBUGSFS is not set.
	Fix: Debugfs entry removal moved inside CONFIG_RSI_DEBUGSFS flag in
             function rsi_mac80211_detach()
Memory leak found and fixed for below structures in function rsi_mac80211_detach()
	* channel list for each supported band
	* rsi debugfs info
Signed-off-by: Prameela Rani Garnepudi <prameela.j04cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

When in AP mode, scans can be done without changing firmware to
the multi-role firmware. Allow the interface to scan if forced
in the scan request.
Signed-off-by: James Minor <james.minor@ni.com>
Signed-off-by: Xander Huff <xander.huff@ni.com>
Reviewed-by: Ben Shelton <ben.shelton@ni.com>
Reviewed-by: Jaeden Amero <jaeden.amero@ni.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Since this driver was added to the kernel, the checkpatch script was
modified to request that the address of the FSF not be included.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Since this driver was added to the kernel, the checkpatch script was
modified to request that the address of the FSF not be included.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>