This firmware is not supported anymore - stop loading this firmware.
Remove code handling older versions.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

There's no need to forward RX MPDUs to notification wait tests, nor
do we need to check them for firmware dump triggers, nor could they
be asynchronous. It's thus more efficient to handle them separately,
before going into the regular RX handlers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

In scenarios where we haven't converged yet to a specific modulation
and rate it could be better to report to userspace the last tx rate
based on the STA capabilities and RSSI. This is important as sometimes
userspace displays the last tx rate as the link speed.
This avoids being presented with low legacy rates when rs just begins
its search or after an idle period in which it resets itself.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Pull networking updates from David Miller:

 1) Add TX fast path in mac80211, from Johannes Berg.

 2) Add TSO/GRO support to ibmveth, from Thomas Falcon

 3) Move away from cached routes in ipv6, just like ipv4, from Martin
    KaFai Lau.

 4) Lots of new rhashtable tests, from Thomas Graf.

 5) Run ingress qdisc lockless, from Alexei Starovoitov.

 6) Allow servers to fetch TCP packet headers for SYN packets of new
    connections, for fingerprinting.  From Eric Dumazet.

 7) Add mode parameter to pktgen, for testing receive.  From Alexei
    Starovoitov.

 8) Cache access optimizations via simplifications of build_skb(), from
    Alexander Duyck.

 9) Move page frag allocator under mm/, also from Alexander.

10) Add xmit_more support to hv_netvsc, from KY Srinivasan.

11) Add a counter guard in case we try to perform endless reclassify
    loops in the packet scheduler.

12) Extern flow dissector to be programmable and use it in new "Flower"
    classifier.  From Jiri Pirko.

13) AF_PACKET fanout rollover fixes, performance improvements, and new
    statistics.  From Willem de Bruijn.

14) Add netdev driver for GENEVE tunnels, from John W Linville.

15) Add ingress netfilter hooks and filtering, from Pablo Neira Ayuso.

16) Fix handling of epoll edge triggers in TCP, from Eric Dumazet.

17) Add an ECN retry fallback for the initial TCP handshake, from Daniel
    Borkmann.

18) Add tail call support to BPF, from Alexei Starovoitov.

19) Add several pktgen helper scripts, from Jesper Dangaard Brouer.

20) Add zerocopy support to AF_UNIX, from Hannes Frederic Sowa.

21) Favor even port numbers for allocation to connect() requests, and
    odd port numbers for bind(0), in an effort to help avoid
    ip_local_port_range exhaustion.  From Eric Dumazet.

22) Add Cavium ThunderX driver, from Sunil Goutham.

23) Allow bpf programs to access skb_iif and dev->ifindex SKB metadata,
    from Alexei Starovoitov.

24) Add support for T6 chips in cxgb4vf driver, from Hariprasad Shenai.

25) Double TCP Small Queues default to 256K to accomodate situations
    like the XEN driver and wireless aggregation.  From Wei Liu.

26) Add more entropy inputs to flow dissector, from Tom Herbert.

27) Add CDG congestion control algorithm to TCP, from Kenneth Klette
    Jonassen.

28) Convert ipset over to RCU locking, from Jozsef Kadlecsik.

29) Track and act upon link status of ipv4 route nexthops, from Andy
    Gospodarek.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1670 commits)
  bridge: vlan: flush the dynamically learned entries on port vlan delete
  bridge: multicast: add a comment to br_port_state_selection about blocking state
  net: inet_diag: export IPV6_V6ONLY sockopt
  stmmac: troubleshoot unexpected bits in des0 & des1
  net: ipv4 sysctl option to ignore routes when nexthop link is down
  net: track link-status of ipv4 nexthops
  net: switchdev: ignore unsupported bridge flags
  net: Cavium: Fix MAC address setting in shutdown state
  drivers: net: xgene: fix for ACPI support without ACPI
  ip: report the original address of ICMP messages
  net/mlx5e: Prefetch skb data on RX
  net/mlx5e: Pop cq outside mlx5e_get_cqe
  net/mlx5e: Remove mlx5e_cq.sqrq back-pointer
  net/mlx5e: Remove extra spaces
  net/mlx5e: Avoid TX CQE generation if more xmit packets expected
  net/mlx5e: Avoid redundant dev_kfree_skb() upon NOP completion
  net/mlx5e: Remove re-assignment of wq type in mlx5e_enable_rq()
  net/mlx5e: Use skb_shinfo(skb)->gso_segs rather than counting them
  net/mlx5e: Static mapping of netdev priv resources to/from netdev TX queues
  net/mlx4_en: Use HW counters for rx/tx bytes/packets in PF device
  ...

Pull scheduler updates from Thomas Gleixner:
 "This series of scheduler updates depends on sched/core and timers/core
  branches, which are already in your tree:

   - Scheduler balancing overhaul to plug a hard to trigger race which
     causes an oops in the balancer (Peter Zijlstra)

   - Lockdep updates which are related to the balancing updates (Peter
     Zijlstra)"

* 'sched-hrtimers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched,lockdep: Employ lock pinning
  lockdep: Implement lock pinning
  lockdep: Simplify lock_release()
  sched: Streamline the task migration locking a little
  sched: Move code around
  sched,dl: Fix sched class hopping CBS hole
  sched, dl: Convert switched_{from, to}_dl() / prio_changed_dl() to balance callbacks
  sched,dl: Remove return value from pull_dl_task()
  sched, rt: Convert switched_{from, to}_rt() / prio_changed_rt() to balance callbacks
  sched,rt: Remove return value from pull_rt_task()
  sched: Allow balance callbacks for check_class_changed()
  sched: Use replace normalize_task() with __sched_setscheduler()
  sched: Replace post_schedule with a balance callback list

Pull locking updates from Thomas Gleixner:
 "These locking updates depend on the alreay merged sched/core branch:

   - Lockless top waiter wakeup for rtmutex (Davidlohr)

   - Reduce hash bucket lock contention for PI futexes (Sebastian)

   - Documentation update (Davidlohr)"

* 'sched-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  locking/rtmutex: Update stale plist comments
  futex: Lower the lock contention on the HB lock during wake up
  locking/rtmutex: Implement lockless top-waiter wakeup

Pull arm64 updates from Catalin Marinas:
 "Mostly refactoring/clean-up:

   - CPU ops and PSCI (Power State Coordination Interface) refactoring
     following the merging of the arm64 ACPI support, together with
     handling of Trusted (secure) OS instances

   - Using fixmap for permanent FDT mapping, removing the initial dtb
     placement requirements (within 512MB from the start of the kernel
     image).  This required moving the FDT self reservation out of the
     memreserve processing

   - Idmap (1:1 mapping used for MMU on/off) handling clean-up

   - Removing flush_cache_all() - not safe on ARM unless the MMU is off.
     Last stages of CPU power down/up are handled by firmware already

   - "Alternatives" (run-time code patching) refactoring and support for
     immediate branch patching, GICv3 CPU interface access

   - User faults handling clean-up

  And some fixes:

   - Fix for VDSO building with broken ELF toolchains

   - Fix another case of init_mm.pgd usage for user mappings (during
     ASID roll-over broadcasting)

   - Fix for FPSIMD reloading after CPU hotplug

   - Fix for missing syscall trace exit

   - Workaround for .inst asm bug

   - Compat fix for switching the user tls tpidr_el0 register"

* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (42 commits)
  arm64: use private ratelimit state along with show_unhandled_signals
  arm64: show unhandled SP/PC alignment faults
  arm64: vdso: work-around broken ELF toolchains in Makefile
  arm64: kernel: rename __cpu_suspend to keep it aligned with arm
  arm64: compat: print compat_sp instead of sp
  arm64: mm: Fix freeing of the wrong memmap entries with !SPARSEMEM_VMEMMAP
  arm64: entry: fix context tracking for el0_sp_pc
  arm64: defconfig: enable memtest
  arm64: mm: remove reference to tlb.S from comment block
  arm64: Do not attempt to use init_mm in reset_context()
  arm64: KVM: Switch vgic save/restore to alternative_insn
  arm64: alternative: Introduce feature for GICv3 CPU interface
  arm64: psci: fix !CONFIG_HOTPLUG_CPU build warning
  arm64: fix bug for reloading FPSIMD state after CPU hotplug.
  arm64: kernel thread don't need to save fpsimd context.
  arm64: fix missing syscall trace exit
  arm64: alternative: Work around .inst assembler bugs
  arm64: alternative: Merge alternative-asm.h into alternative.h
  arm64: alternative: Allow immediate branch as alternative instruction
  arm64: Rework alternate sequence for ARM erratum 845719
  ...

Pull first batch of KVM updates from Paolo Bonzini:
 "The bulk of the changes here is for x86.  And for once it's not for
  silicon that no one owns: these are really new features for everyone.

  Details:

   - ARM:
        several features are in progress but missed the 4.2 deadline.
        So here is just a smattering of bug fixes, plus enabling the
        VFIO integration.

   - s390:
        Some fixes/refactorings/optimizations, plus support for 2GB
        pages.

   - x86:
        * host and guest support for marking kvmclock as a stable
          scheduler clock.
        * support for write combining.
        * support for system management mode, needed for secure boot in
          guests.
        * a bunch of cleanups required for the above
        * support for virtualized performance counters on AMD
        * legacy PCI device assignment is deprecated and defaults to "n"
          in Kconfig; VFIO replaces it

        On top of this there are also bug fixes and eager FPU context
        loading for FPU-heavy guests.

   - Common code:
        Support for multiple address spaces; for now it is used only for
        x86 SMM but the s390 folks also have plans"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (124 commits)
  KVM: s390: clear floating interrupt bitmap and parameters
  KVM: x86/vPMU: Enable PMU handling for AMD PERFCTRn and EVNTSELn MSRs
  KVM: x86/vPMU: Implement AMD vPMU code for KVM
  KVM: x86/vPMU: Define kvm_pmu_ops to support vPMU function dispatch
  KVM: x86/vPMU: introduce kvm_pmu_msr_idx_to_pmc
  KVM: x86/vPMU: reorder PMU functions
  KVM: x86/vPMU: whitespace and stylistic adjustments in PMU code
  KVM: x86/vPMU: use the new macros to go between PMC, PMU and VCPU
  KVM: x86/vPMU: introduce pmu.h header
  KVM: x86/vPMU: rename a few PMU functions
  KVM: MTRR: do not map huge page for non-consistent range
  KVM: MTRR: simplify kvm_mtrr_get_guest_memory_type
  KVM: MTRR: introduce mtrr_for_each_mem_type
  KVM: MTRR: introduce fixed_mtrr_addr_* functions
  KVM: MTRR: sort variable MTRRs
  KVM: MTRR: introduce var_mtrr_range
  KVM: MTRR: introduce fixed_mtrr_segment table
  KVM: MTRR: improve kvm_mtrr_get_guest_memory_type
  KVM: MTRR: do not split 64 bits MSR content
  KVM: MTRR: clean up mtrr default type
  ...

Pull powerpc updates from Michael Ellerman:

 - disable the 32-bit vdso when building LE, so we can build with a
   64-bit only toolchain.

 - EEH fixes from Gavin & Richard.

 - enable the sys_kcmp syscall from Laurent.

 - sysfs control for fastsleep workaround from Shreyas.

 - expose OPAL events as an irq chip by Alistair.

 - MSI ops moved to pci_controller_ops by Daniel.

 - fix for kernel to userspace backtraces for perf from Anton.

 - merge pseries and pseries_le defconfigs from Cyril.

 - CXL in-kernel API from Mikey.

 - OPAL prd driver from Jeremy.

 - fix for DSCR handling & tests from Anshuman.

 - Powernv flash mtd driver from Cyril.

 - dynamic DMA Window support on powernv from Alexey.

 - LLVM clang fixes & workarounds from Anton.

 - reworked version of the patch to abort syscalls when transactional.

 - fix the swap encoding to support 4TB, from Aneesh.

 - various fixes as usual.

 - Freescale updates from Scott: Highlights include more 8xx
   optimizations, an e6500 hugetlb optimization, QMan device tree nodes,
   t1024/t1023 support, and various fixes and cleanup.

* tag 'powerpc-4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (180 commits)
  cxl: Fix typo in debug print
  cxl: Add CXL_KERNEL_API config option
  powerpc/powernv: Fix wrong IOMMU table in pnv_ioda_setup_bus_dma()
  powerpc/mm: Change the swap encoding in pte.
  powerpc/mm: PTE_RPN_MAX is not used, remove the same
  powerpc/tm: Abort syscalls in active transactions
  powerpc/iommu/ioda2: Enable compile with IOV=on and IOMMU_API=off
  powerpc/include: Add opal-prd to installed uapi headers
  powerpc/powernv: fix construction of opal PRD messages
  powerpc/powernv: Increase opal-irqchip initcall priority
  powerpc: Make doorbell check preemption safe
  powerpc/powernv: pnv_init_idle_states() should only run on powernv
  macintosh/nvram: Remove as unused
  powerpc: Don't use gcc specific options on clang
  powerpc: Don't use -mno-strict-align on clang
  powerpc: Only use -mtraceback=no, -mno-string and -msoft-float if toolchain supports it
  powerpc: Only use -mabi=altivec if toolchain supports it
  powerpc: Fix duplicate const clang warning in user access code
  vfio: powerpc/spapr: Support Dynamic DMA windows
  vfio: powerpc/spapr: Register memory and define IOMMU v2
  ...

Pull s390 updates from Martin Schwidefsky:
 "Pretty boring for a merge window pull.

  One change in behaviour is the patch for dasd driver, the module which
  provides the diagnose discipline is now loaded automatically.

  The SCLP code got a nice cleanup, a new global structure replaces a
  bunch of accessor functions.

  And a couple of random, small improvements"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/pci: improve handling of hotplug event 0x301
  s390/setup: fix DMA_API_DEBUG warnings
  s390/zcrypt: remove obsolete __constant
  s390/keyboard: avoid off-by-one when using strnlen_user()
  s390/sclp: pass timeout as HZ independent value
  s390/mm: s/specifiation/specification/, s/an specification/a specification/
  s390/sclp: Use DECLARE_BITMAP
  s390/dasd: Enable automatic loading of dasd_diag_mod
  s390/sclp: move sclp_facilities into "struct sclp"
  s390/sclp: get rid of sclp_get_mtid() and sclp_get_mtid_max()
  s390/sclp: unify basic sclp access by exposing "struct sclp"
  s390/sclp: prepare smp_fill_possible_mask for global "struct sclp"

Pull Microblaze updates from Michal Simek:

 - some PCI fixups

 - add new MB versions

 - sparse fixups

* tag 'microblaze-4.2-rc1' of git://git.monstr.eu/linux-2.6-microblaze:
  microblaze/PCI: Remove unnecessary struct pci_dev declaration
  microblaze/PCI: Remove unnecessary pci_bus_find_capability() declaration
  microblaze/PCI: Remove unused declarations
  microblaze: Label local function static
  microblaze: Add missing release version code

Add a new argument to br_fdb_delete_by_port which allows to specify a
vid to match when flushing entries and use it in nbp_vlan_delete() to
flush the dynamically learned entries of the vlan/port pair when removing
a vlan from a port. Before this patch only the local mac was being
removed and the dynamically learned ones were left to expire.
Note that the do_all argument is still respected and if specified, the
vid will be ignored.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a comment to explain why we're not disabling port's multicast when it
goes in blocking state. Since there's a check in the timer's function which
bypasses the timer if the port's in blocking/disabled state, the timer will
simply expire and stop without sending more queries.
Suggested-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/ethernet/mellanox/mlx4/main.c
	net/packet/af_packet.c

Both conflicts were cases of simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>

For AF_INET6 sockets, the value of struct ipv6_pinfo.ipv6only is
exported to userspace. It indicates whether a socket bound to in6addr_any
listens on IPv4 as well as IPv6. Since the socket is natively IPv6, it is not
listed by e.g. 'ss -l -4'.

This patch is accompanied by an appropriate one for iproute2 to enable
the additional information in 'ss -e'.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

Current implementation of descriptor init procedure only takes
care about setting/clearing ownership flag in "des0"/"des1"
fields while it is perfectly possible to get unexpected bits
set because of the following factors:

 [1] On driver probe underlying memory allocated with
     dma_alloc_coherent() might not be zeroed and so
     it will be filled with garbage.

 [2] During driver operation some bits could be set by SD/MMC
     controller (for example error flags etc).

And unexpected and/or randomly set flags in "des0"/"des1"
fields may lead to unpredictable behavior of GMAC DMA block.

This change addresses both items above with:

 [1] Use of dma_zalloc_coherent() instead of simple
     dma_alloc_coherent() to make sure allocated memory is
     zeroed. That shouldn't affect performance because
     this allocation only happens once on driver probe.

 [2] Do explicit zeroing of both "des0" and "des1" fields
     of all buffer descriptors during initialization of
     DMA transfer.

And while at it fixed identation of dma_free_coherent()
counterpart as well.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: arc-linux-dev@synopsys.com
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org
Cc: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andy Gospodarek says:

====================
changes to make ipv4 routing table aware of next-hop link status

This series adds the ability to have the Linux kernel track whether or
not a particular route should be used based on the link-status of the
interface associated with the next-hop.

Before this patch any link-failure on an interface that was serving as a
gateway for some systems could result in those systems being isolated
from the rest of the network as the stack would continue to attempt to
send frames out of an interface that is actually linked-down.  When the
kernel is responsible for all forwarding, it should also be responsible
for taking action when the traffic can no longer be forwarded -- there
is no real need to outsource link-monitoring to userspace anymore.

This feature is only enabled with the new per-interface or ipv4 global
sysctls called 'ignore_routes_with_linkdown'.

net.ipv4.conf.all.ignore_routes_with_linkdown = 0
net.ipv4.conf.default.ignore_routes_with_linkdown = 0
net.ipv4.conf.lo.ignore_routes_with_linkdown = 0
...

When the above sysctls are set, the kernel will not only report to
userspace that the link is down, but it will also report to userspace
that a route is dead.  This will signal to userspace that the route will
not be selected.

With the new sysctls set, the following behavior can be observed
(interface p8p1 is link-down):

default via 10.0.5.2 dev p9p1
10.0.5.0/24 dev p9p1  proto kernel  scope link  src 10.0.5.15
70.0.0.0/24 dev p7p1  proto kernel  scope link  src 70.0.0.1
80.0.0.0/24 dev p8p1  proto kernel  scope link  src 80.0.0.1 dead linkdown
90.0.0.0/24 via 80.0.0.2 dev p8p1  metric 1 dead linkdown
90.0.0.0/24 via 70.0.0.2 dev p7p1  metric 2
90.0.0.1 via 70.0.0.2 dev p7p1  src 70.0.0.1
    cache
local 80.0.0.1 dev lo  src 80.0.0.1
    cache <local>
80.0.0.2 via 10.0.5.2 dev p9p1  src 10.0.5.15
    cache

While the route does remain in the table (so it can be modified if
needed rather than being wiped away as it would be if IFF_UP was
cleared), the proper next-hop is chosen automatically when the link is
down.  Now interface p8p1 is linked-up:

default via 10.0.5.2 dev p9p1
10.0.5.0/24 dev p9p1  proto kernel  scope link  src 10.0.5.15
70.0.0.0/24 dev p7p1  proto kernel  scope link  src 70.0.0.1
80.0.0.0/24 dev p8p1  proto kernel  scope link  src 80.0.0.1
90.0.0.0/24 via 80.0.0.2 dev p8p1  metric 1
90.0.0.0/24 via 70.0.0.2 dev p7p1  metric 2
192.168.56.0/24 dev p2p1  proto kernel  scope link  src 192.168.56.2
90.0.0.1 via 80.0.0.2 dev p8p1  src 80.0.0.1
    cache
local 80.0.0.1 dev lo  src 80.0.0.1
    cache <local>
80.0.0.2 dev p8p1  src 80.0.0.1
    cache

and the output changes to what one would expect.

If the global or interface sysctl is not set, the following output would
be expected when p8p1 is down:

default via 10.0.5.2 dev p9p1
10.0.5.0/24 dev p9p1  proto kernel  scope link  src 10.0.5.15
70.0.0.0/24 dev p7p1  proto kernel  scope link  src 70.0.0.1
80.0.0.0/24 dev p8p1  proto kernel  scope link  src 80.0.0.1 linkdown
90.0.0.0/24 via 80.0.0.2 dev p8p1  metric 1 linkdown
90.0.0.0/24 via 70.0.0.2 dev p7p1  metric 2

If the dead flag does not appear there should be no expectation that the
kernel would skip using this route due to link being down.

v2: Split kernel changes into 2 patches: first to add linkdown flag and
second to add new sysctl settings.  Also took suggestion from Alex to
simplify code by only checking sysctl during fib lookup and suggestion
from Scott to add a per-interface sysctl.  Added iproute2 patch to
recognize and print linkdown flag.

v3: Code cleanups along with reverse-path checks suggested by Alex and
small fixes related to problems found when multipath was disabled.

v4: Drop binary sysctls

v5: Whitespace and variable declaration fixups suggested by Dave

v6: Style changes noticed by Dave and checkpath suggestions.

v7: Last checkpatch fixup.

Though there were some that preferred not to have a configuration option
and to make this behavior the default when it was discussed in Ottawa
earlier this year since "it was time to do this."  I wanted to propose
the config option to preserve the current behavior for those that desire
it.  I'll happily remove it if Dave and Linus approve.

An IPv6 implementation is also needed (DECnet too!), but I wanted to
start with the IPv4 implementation to get people comfortable with the
idea before moving forward.  If this is accepted the IPv6 implementation
can be posted shortly.

There was also a request for switchdev support for this, but that will
be posted as a followup as switchdev does not currently handle dead
next-hops in a multi-path case and I felt that infra needed to be added
first.

FWIW, we have been running the original version of this series with a
global sysctl and our customers have been happily using a backported
version for IPv4 and IPv6 for >6 months.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This feature is only enabled with the new per-interface or ipv4 global
sysctls called 'ignore_routes_with_linkdown'.

net.ipv4.conf.all.ignore_routes_with_linkdown = 0
net.ipv4.conf.default.ignore_routes_with_linkdown = 0
net.ipv4.conf.lo.ignore_routes_with_linkdown = 0
...

When the above sysctls are set, will report to userspace that a route is
dead and will no longer resolve to this nexthop when performing a fib
lookup.  This will signal to userspace that the route will not be
selected.  The signalling of a RTNH_F_DEAD is only passed to userspace
if the sysctl is enabled and link is down.  This was done as without it
the netlink listeners would have no idea whether or not a nexthop would
be selected.   The kernel only sets RTNH_F_DEAD internally if the
interface has IFF_UP cleared.

With the new sysctl set, the following behavior can be observed
(interface p8p1 is link-down):

default via 10.0.5.2 dev p9p1
10.0.5.0/24 dev p9p1  proto kernel  scope link  src 10.0.5.15
70.0.0.0/24 dev p7p1  proto kernel  scope link  src 70.0.0.1
80.0.0.0/24 dev p8p1  proto kernel  scope link  src 80.0.0.1 dead linkdown
90.0.0.0/24 via 80.0.0.2 dev p8p1  metric 1 dead linkdown
90.0.0.0/24 via 70.0.0.2 dev p7p1  metric 2
90.0.0.1 via 70.0.0.2 dev p7p1  src 70.0.0.1
    cache
local 80.0.0.1 dev lo  src 80.0.0.1
    cache <local>
80.0.0.2 via 10.0.5.2 dev p9p1  src 10.0.5.15
    cache

While the route does remain in the table (so it can be modified if
needed rather than being wiped away as it would be if IFF_UP was
cleared), the proper next-hop is chosen automatically when the link is
down.  Now interface p8p1 is linked-up:

default via 10.0.5.2 dev p9p1
10.0.5.0/24 dev p9p1  proto kernel  scope link  src 10.0.5.15
70.0.0.0/24 dev p7p1  proto kernel  scope link  src 70.0.0.1
80.0.0.0/24 dev p8p1  proto kernel  scope link  src 80.0.0.1
90.0.0.0/24 via 80.0.0.2 dev p8p1  metric 1
90.0.0.0/24 via 70.0.0.2 dev p7p1  metric 2
192.168.56.0/24 dev p2p1  proto kernel  scope link  src 192.168.56.2
90.0.0.1 via 80.0.0.2 dev p8p1  src 80.0.0.1
    cache
local 80.0.0.1 dev lo  src 80.0.0.1
    cache <local>
80.0.0.2 dev p8p1  src 80.0.0.1
    cache

and the output changes to what one would expect.

If the sysctl is not set, the following output would be expected when
p8p1 is down:

default via 10.0.5.2 dev p9p1
10.0.5.0/24 dev p9p1  proto kernel  scope link  src 10.0.5.15
70.0.0.0/24 dev p7p1  proto kernel  scope link  src 70.0.0.1
80.0.0.0/24 dev p8p1  proto kernel  scope link  src 80.0.0.1 linkdown
90.0.0.0/24 via 80.0.0.2 dev p8p1  metric 1 linkdown
90.0.0.0/24 via 70.0.0.2 dev p7p1  metric 2

Since the dead flag does not appear, there should be no expectation that
the kernel would skip using this route due to link being down.

v2: Split kernel changes into 2 patches, this actually makes a
behavioral change if the sysctl is set.  Also took suggestion from Alex
to simplify code by only checking sysctl during fib lookup and
suggestion from Scott to add a per-interface sysctl.

v3: Code clean-ups to make it more readable and efficient as well as a
reverse path check fix.

v4: Drop binary sysctl

v5: Whitespace fixups from Dave

v6: Style changes from Dave and checkpatch suggestions

v7: One more checkpatch fixup
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: Dinesh Dutt <ddutt@cumulusnetworks.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a fib flag called RTNH_F_LINKDOWN to any ipv4 nexthops that are
reachable via an interface where carrier is off.  No action is taken,
but additional flags are passed to userspace to indicate carrier status.

This also includes a cleanup to fib_disable_ip to more clearly indicate
what event made the function call to replace the more cryptic force
option previously used.

v2: Split out kernel functionality into 2 patches, this patch simply
sets and clears new nexthop flag RTNH_F_LINKDOWN.

v3: Cleanups suggested by Alex as well as a bug noticed in
fib_sync_down_dev and fib_sync_up when multipath was not enabled.

v5: Whitespace and variable declaration fixups suggested by Dave.

v6: Style fixups noticed by Dave; ran checkpatch to be sure I got them
all.
Signed-off-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: Dinesh Dutt <ddutt@cumulusnetworks.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

switchdev_port_bridge_getlink() queries SWITCHDEV_ATTR_PORT_BRIDGE_FLAGS
attributes, but a driver doesn't need to implement this in order to get
bridge link information.

So error out only on errors different than -EOPNOTSUPP.

(This is a follow-up patch for 7d4f8d87.)

Fixes: 8793d0a6 ("switchdev: add new switchdev_port_bridge_getlink")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This bug pops up with NetworkManager on Fedora 21. NetworkManager tends to
stop the interface (nicvf_stop() is called) before changing settings. In
stopped state MAC cannot be sent to a PF. However, when the interface is
restarted (nicvf_open() is called), we ping the PF using NIC_MBOX_MSG_READY
message, and the PF replies back with old MAC address, overriding what we
had after MAC setting from userspace. As a result, we cannot set MAC
address using NetworkManager.

This patch introduces special tracking of MAC change in stopped state so
that the correct new MAC address is sent to a PF when interface is reopen.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

ICMP messages can trigger ICMP and local errors. In this case
serr->port is 0 and starting from Linux 4.0 we do not return
the original target address to the error queue readers.
Add function to define which errors provide addr_offset.
With this fix my ping command is not silent anymore.

Fixes: c247f053 ("ip: fix error queue empty skb handling")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Or Gerlitz says:

====================
Mellanox NIC drivers update, June 23 2015

This series has two fixes from Eran to his recent SRIOV counters work in
mlx4 and few more updates from Saeed and Achiad to the mlx5 Ethernet
code. All fixes here relate to net-next code, so no need for -stable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Prefetch the 1st cache line used by the buffer pointed by
the skb linear data.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Separate between mlx5e_get_cqe() and mlx5_cqwq_pop(), this helps for
better code readability and better CQ buffer management.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use container_of() instead.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Coding Style fix, remove extra spaces.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In order to save PCI BW consumed by TX CQEs and to reduce the amount of
CPU cache misses caused by TX CQE reading, we request TX CQE generation
only when skb->xmit_more=0.

As a consequence of the above, a single TX CQE may now indicate the
transmission completion of multiple TX SKBs.

This also handles a problem introduced in commit b1b8105ebf41 "net/mlx5e:
Support NETIF_F_SG" where we didn't ask for NOP completions while the
driver didn't have the proper code to handle this case.

Fixes: b1b8105ebf41 ('net/mlx5e: Support NETIF_F_SG')
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

NOP completion SKBs are always NULL.
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It is already assigned at mlx5e_build_rq_param()
Signed-off-by: Achiad Shochat <achiad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of counting number of gso fragments, we can use
skb_shinfo(skb)->gso_segs.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To save per-packet calculations, we use the following static mappings:
1) priv {channel, tc} to netdev txq (used @mlx5e_selec_queue())
2) netdev txq to priv sq (used @mlx5e_xmit())

Thanks to these static mappings, no more need for a separate implementation
of ndo_start_xmit when multiple TCs are configured.
We believe the performance improvement of such separation would be negligible, if any.
The previous way of dynamically calculating the above mappings required
allocating more TX queues than actually used (@alloc_etherdev_mqs()),
which is now no longer needed.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Under SRIOV, the port rx/tx bytes/packets statistics should by read
from the HW instead of using the PF netdevice SW accounting. This is
needed in order to get the full port statistics and not just the PF
own ones
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

NUM_ALL_STATS was not updated with the new four entries, instead
NUM_FLOW_STATS was updated, fix it. that caused off-by-four for all
counters below pf_*_*.

Fixes: b42de4d0 ('net/mlx4_en: Show PF own statistics via ethtool')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull IOMMU updates from Joerg Roedel:
 "This time with bigger changes than usual:

   - A new IOMMU driver for the ARM SMMUv3.

     This IOMMU is pretty different from SMMUv1 and v2 in that it is
     configured through in-memory structures and not through the MMIO
     register region.  The ARM SMMUv3 also supports IO demand paging for
     PCI devices with PRI/PASID capabilities, but this is not
     implemented in the driver yet.

   - Lots of cleanups and device-tree support for the Exynos IOMMU
     driver.  This is part of the effort to bring Exynos DRM support
     upstream.

   - Introduction of default domains into the IOMMU core code.

     The rationale behind this is to move functionalily out of the IOMMU
     drivers to common code to get to a unified behavior between
     different drivers.  The patches here introduce a default domain for
     iommu-groups (isolation groups).

     A device will now always be attached to a domain, either the
     default domain or another domain handled by the device driver.  The
     IOMMU drivers have to be modified to make use of that feature.  So
     long the AMD IOMMU driver is converted, with others to follow.

   - Patches for the Intel VT-d drvier to fix DMAR faults that happen
     when a kdump kernel boots.

     When the kdump kernel boots it re-initializes the IOMMU hardware,
     which destroys all mappings from the crashed kernel.  As this
     happens before the endpoint devices are re-initialized, any
     in-flight DMA causes a DMAR fault.  These faults cause PCI master
     aborts, which some devices can't handle properly and go into an
     undefined state, so that the device driver in the kdump kernel
     fails to initialize them and the dump fails.

     This is now fixed by copying over the mapping structures (only
     context tables and interrupt remapping tables) from the old kernel
     and keep the old mappings in place until the device driver of the
     new kernel takes over.  This emulates the the behavior without an
     IOMMU to the best degree possible.

   - A couple of other small fixes and cleanups"

* tag 'iommu-updates-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (69 commits)
  iommu/amd: Handle large pages correctly in free_pagetable
  iommu/vt-d: Don't disable IR when it was previously enabled
  iommu/vt-d: Make sure copied over IR entries are not reused
  iommu/vt-d: Copy IR table from old kernel when in kdump mode
  iommu/vt-d: Set IRTA in intel_setup_irq_remapping
  iommu/vt-d: Disable IRQ remapping in intel_prepare_irq_remapping
  iommu/vt-d: Move QI initializationt to intel_setup_irq_remapping
  iommu/vt-d: Move EIM detection to intel_prepare_irq_remapping
  iommu/vt-d: Enable Translation only if it was previously disabled
  iommu/vt-d: Don't disable translation prior to OS handover
  iommu/vt-d: Don't copy translation tables if RTT bit needs to be changed
  iommu/vt-d: Don't do early domain assignment if kdump kernel
  iommu/vt-d: Allocate si_domain in init_dmars()
  iommu/vt-d: Mark copied context entries
  iommu/vt-d: Do not re-use domain-ids from the old kernel
  iommu/vt-d: Copy translation tables from old kernel
  iommu/vt-d: Detect pre enabled translation
  iommu/vt-d: Make root entry visible for hardware right after allocation
  iommu/vt-d: Init QI before root entry is allocated
  iommu/vt-d: Cleanup log messages
  ...

Pull MTD updates from Brian Norris:
 "JFFS2:
   - fix a theoretical unbalanced locking issue; the lock handling was a
     bit unclean, but AFAICT, it didn't actually lead to real deadlocks

  NAND:
   - brcmnand driver: new driver supporting NAND controller found
     originally on Broadcom STB SoCs (BCM7xxx), but now also found on
     BCM63xxx, iProc (e.g., Cygnus, BCM5301x), BCM3xxx, and more

   - begin factoring out BBT code so it can be shared between
     traditional (parallel) NAND drivers and upcoming SPI NAND drivers
     (WIP)

   - add common DT-based init support, so nand_base can pick up some
     flash properties automatically, using established common NAND DT
     properties

   - mxc_nand: support 8-bit ECC

   - pxa3xx_nand:
     * fix build for ARM64
     * use a jiffies-based timeout

  SPI NOR:
   - add a few new IDs

   - clear out some unnecessary entries

   - make sure SECT_4K flags are correct for all (?) entries

  Core:
   - fix mtd->usecount race conditions (BUG_ON())

   - switch to modern PM ops

  Other:
   - CFI: save code space by de-inlining large functions

   - clean up some partition parser selection code across several
     drivers

   - various miscellaneous changes, mostly minor"

* tag 'for-linus-20150623' of git://git.infradead.org/linux-mtd: (57 commits)
  mtd: docg3: Fix kasprintf() usage
  mtd: docg3: Don't leak docg3->bbt in error path
  mtd: nandsim: Fix kasprintf() usage
  mtd: cs553x_nand: Fix kasprintf() usage
  mtd: r852: Fix device_create_file() usage
  mtd: brcmnand: drop unnecessary initialization
  mtd: propagate error codes from add_mtd_device()
  mtd: diskonchip: remove two-phase partitioning / registration
  mtd: dc21285: use raw spinlock functions for nw_gpio_lock
  mtd: chips: fixup dependencies, to prevent build error
  mtd: cfi_cmdset_0002: Initialize datum before calling map_word_load_partial
  mtd: cfi: deinline large functions
  mtd: lantiq-flash: use default partition parsers
  mtd: plat_nand: use default partition probe
  mtd: nand: correct indentation within conditional
  mtd: remove incorrect file name
  mtd: blktrans: use better error code for unimplemented ioctl()
  mtd: maps: Spelling s/reseved/reserved/
  mtd: blktrans: change blktrans_getgeo return value
  mtd: mxc_nand: generate nand_ecclayout for 8 bit ECC
  ...

Pull MFD updates from Lee Jones:
 "Changes to existing drivers:
   - Constify structures; throughout the subsystem
   - Move support to DT in; cros_ec
   - DT changes and documentation; cros-ec, max77693, max77686, arizona, da9063
   - ACPI changes and documentation; mfd-core
   - Use different platform specific API in; cros_ec_*, arizona-core
   - Remove unused parent field from; cros_ec_i2c
   - Add wake-up/reset delay in; cross_ec_spi, arizona-core
   - Staticise structures/functions in; cros_ec
   - Remove redundant code; arizona-core, max77686
   - Bugfix; twl4030-power
   - Allow compile test; aat2870, tps65910
   - MAINTAINERS adaptions; samsung, syscon
   - Resource Management (devm_*); arizona-core
   - Refactor Reset code; arizona-core
   - Insist on at least one full boot; arizona-core
   - Trivial formatting; arizona-core
   - Add low-power-sleep; arizona-core
   - IRQ ONESHOT changes; twl4030-irq, mc13xxx-core, wm831x-auxadc, htc-i2cpld,
                          wm8350-core, ab8500-debugfs, ab8500-gpadc, si476x-i2c

  (Re-)moved drivers:
   - Move protocol helpers out to drivers/platform; cros_ec

  New drivers/supported devices:
   - Add support for AXP22x into axp20x
   - Add support for OnKey into da9063-core
   - Add support for Pinctrl into mt6397-core
   - New STMicroelectronics LPC Watchdog driver
   - New STMicroelectronics LPC Real-Time Clock driver"

* tag 'mfd-for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (59 commits)
  mfd: lpc_ich: Assign subdevice ids automatically
  mfd: si476x-i2c: Pass the IRQF_ONESHOT flag
  mfd: ab8500-gpadc: Pass the IRQF_ONESHOT flag
  mfd: ab8500-debugfs: Pass the IRQF_ONESHOT flag
  mfd: wm8350-core: Pass the IRQF_ONESHOT flag
  mfd: htc-i2cpld: Pass the IRQF_ONESHOT flag
  mfd: wm831x-auxadc: Pass the IRQF_ONESHOT flag
  mfd: mc13xxx-core: Pass the IRQF_ONESHOT flag
  mfd: twl4030-irq: Pass the IRQF_ONESHOT flag
  mfd: mt6397-core: Add GPIO sub-module support
  mfd: arizona: Add convience defines for micd_rate/micd_bias_starttime
  mfd: dt: Add bindings for DA9063 OnKey
  mfd: da9063: Add support for OnKey driver
  mfd: arizona: Fix incorrect Makefile conditionals
  mfd: arizona: Add stub for wm5102_patch()
  mfd: Check ACPI device companion before checking resources
  Documentation: Add WM8998/WM1814 device tree bindings
  mfd: arizona: Split INx_MODE into two fields
  mfd: wm5110: Add delay before releasing reset line
  mfd: arizona: Add better support for system suspend
  ...

Pull regulator updates from Mark Brown:
 "Another fairly quiet release, some new drivers with generic handling
  for minor features but nothing that makes a substantial difference
  outside of the subsystem or for most boards:

   - support for a bunch of new parameters which are present on enough
     regulators to be worth having generic handling for in the
     framework.

   - fixes for some issues with printing constraints during boot which
     should probably have gone in for v4.1 but didn't.

   - new drivers for Dialog DA9062, Maxim MAX77621 and Qualcomm SPMI
     regulators"

* tag 'regulator-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (45 commits)
  regulator: qcom_spmi: Fix calculating number of voltages
  regulator: qcom_spmi: Add missing braces for aligned code
  regulator: fix simple_return.cocci warnings
  regulator: Add QCOM SPMI regulator driver
  regulator: Add docbook for soft start
  regulator: Add input current limit support
  regulator: Add soft start support
  regulator: Add pull down support
  regulator: Add system_load constraint
  regulator: max8973: Fix up ramp_delay for MAX8973_RAMP_25mV_PER_US case
  regulator: core: replace sprintf with scnprintf
  regulator: core: fix constraints output buffer
  regulator: core: Don't corrupt display when printing uV offsets
  regulator: max8973: add support for MAX77621
  regulator: max8973: configure ramp delay through callback
  regulator: pwm-regulator: Diffientiate between dev (device) and rdev (regulator_dev)
  regulator: pwm-regulator: Remove superfluous is_enabled check
  regulator: pwm-regulator: Remove unnecessary descriptor attribute from ddata
  regulator: core: Don't spew backtraces on duplicate sysfs
  regulator: da9063: Fix up irq leak
  ...

Pull spi updates from Mark Brown:
 "No framework updates for the SPI API this time around aside from one
  small fix, just driver improvments.  Some highlights include:

   - New driver support for CSR USP, Mikrotik RB4xx and Zynq GQSPI
     controllers.

   - Modernisation of the OMAP McSPI controller driver, moving it to
     current APIs to enable support for a wider range of client drivers.

   - DMA support for the bcm2835 controller"

* tag 'spi-v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (60 commits)
  spi: zynq: Remove execute bit
  spi: atmel: add support to FIFOs
  spi: atmel: update DT bindings documentation
  spi: spi-fsl-dspi: Update DT binding documentation
  spi: pxa2xx: Constify ACPI device ids
  spi: Add support for Zynq Ultrascale+ MPSoC GQSPI controller
  spi: zynq: Add DT bindings documentation for Zynq Ultrascale+ MPSoC GQSPI controller
  spi: fsl-dspi: Use pinctrl PM helpers
  spi: davinci: change the lower limit of pre-scale divider to 1
  spi: spi-fsl-dspi: Change the way of increasing spi_message->actual_length
  spi: spi-fsl-dspi: Enable TCF interrupt mode support
  spi: atmel: add support for the internal chip-select of the spi controller
  spi: spi-pxa2xx: remove legacy PXA DMA bits
  spi: pxa2xx: Make LPSS SPI general register optional
  spi: pxa2xx: Prepare for new Intel LPSS SPI type
  spi: pxa2xx: Differentiate Intel LPSS types
  spi: restore rx/tx_buf in case of unset CONFIG_HAS_DMA
  spi: rspi: Re-do the returning value of qspi_transfer_out_in
  spi: rspi: modify the name of "qspi_trigger_transfer_out_int" function
  spi: orion: Fix extended baud rates for each Armada SoCs
  ...