- 14 Dec, 2014 40 commits
-
-
Pali Rohár authored
commit 4ab8f7f3 upstream. 5th and 6th byte of ALPS trackstick V3 protocol match condition for first byte of PS/2 3 bytes packet. When driver enters out of sync state and ALPS trackstick is sending data then driver match 5th, 6th and next 1st bytes as PS/2. It basically means if user is using trackstick when driver is in out of sync state driver will never resync. Processing these bytes as 3 bytes PS/2 data cause total mess (random cursor movements, random clicks) and make trackstick unusable until psmouse driver decide to do full device reset. Lot of users reported problems with ALPS devices on Dell Latitude E6440, E6540 and E7440 laptops. ALPS device or Dell EC for unknown reason send some invalid ALPS PS/2 bytes which cause driver out of sync. It looks like that i8042 and psmouse/alps driver always receive group of 6 bytes packets so there are no missing bytes and no bytes were inserted between valid ones. This patch does not fix root of problem with ALPS devices found in Dell Latitude laptops but it does not allow to process some (invalid) subsequence of 6 bytes ALPS packets as 3 bytes PS/2 when driver is out of sync. So with this patch trackstick input device does not report bogus data when also driver is out of sync, so trackstick should be usable on those machines. Signed-off-by:
Pali Rohár <pali.rohar@gmail.com> Tested-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
Ben Hutchings <ben@decadent.org.uk>
-
Thor Thayer authored
commit 0a8727e6 upstream. An IOCTL call that calls spi_setup() and then dw_spi_setup() will overwrite the persisted last transfer speed. On each transfer, the SPI speed is compared to the last transfer speed to determine if the clock divider registers need to be updated (did the speed change?). This bug was observed with the spidev driver using spi-config to update the max transfer speed. This fix: Don't overwrite the persisted last transaction clock speed when updating the SPI parameters in dw_spi_setup(). On the next transaction, the new speed won't match the persisted last speed and the hardware registers will be updated. On initialization, the persisted last transaction clock speed will be 0 but will be updated after the first SPI transaction. Move zeroed clock divider check into clock change test because chip->clk_div is zero on startup and would cause a divide-by-zero error. The calculation was wrong as well (can't support odd #). Reported-by:
Vlastimil Setka <setka@vsis.cz> Signed-off-by:
Thor Thayer <tthayer@opensource.altera.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Imre Deak authored
commit 9e326f78 upstream. We can call this function for a dummy console that doesn't support setting the font mapping, which will result in a null ptr BUG. So check for this case and return error for consoles w/o font mapping support. Reference: https://bugzilla.kernel.org/show_bug.cgi?id=59321Signed-off-by:
Imre Deak <imre.deak@intel.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.2: this function doesn't take a lock, so doesn't need to unlock on error] Signed-off-by:
-
Peter Hurley authored
commit 37b16457 upstream. Kernel oops can cause the tty to be unreleaseable (for example, if n_tty_read() crashes while on the read_wait queue). This will cause tty_release() to endlessly loop without sleeping. Use a killable sleep timeout which grows by 2n+1 jiffies over the interval [0, 120 secs.) and then jumps to forever (but still killable). NB: killable just allows for the task to be rewoken manually, not to be terminated. Signed-off-by:
Peter Hurley <peter@hurleysoftware.com> Signed-off-by:
-
Peter Hurley authored
commit 547039ec upstream. uart_get_baud_rate() will return baud == 0 if the max rate is set to the "magic" 38400 rate and the SPD_* flags are also specified. On the first iteration, if the current baud rate is higher than the max, the baud rate is clamped at the max (which in the degenerate case is 38400). On the second iteration, the now-"magic" 38400 baud rate selects the possibly higher alternate baud rate indicated by the SPD_* flag. Since only two loop iterations are performed, the loop is exited, a kernel WARNING is generated and a baud rate of 0 is returned. Reproducible with: setserial /dev/ttyS0 spd_hi base_baud 38400 Only perform the "magic" 38400 -> SPD_* baud transform on the first loop iteration, which prevents the degenerate case from recognizing the clamped baud rate as the "magic" 38400 value. Reported-by:
Robert Święcki <robert@swiecki.net> Signed-off-by:
-
Johan Hovold authored
commit 4473d054 upstream. Make sure to only raise DTR on transitions from B0 in set_termios. Also allow set_termios to be called from open with a termios_old of NULL. Note that DTR will not be raised prematurely in this case. Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Lars-Peter Clausen authored
commit b598aacc upstream. "raw" is a property of a channel, but should not be part of the name of channel. Signed-off-by:
Lars-Peter Clausen <lars@metafoo.de> Signed-off-by:
Jonathan Cameron <jic23@kernel.org> [bwh: Backported to 3.2: using IIO_CHAN() macro to initialise the structures] Signed-off-by:
-
Takashi Iwai authored
commit 0725dda2 upstream. Some USB-audio devices show weird sysfs warnings at disconnecting the devices, e.g. usb 1-3: USB disconnect, device number 3 ------------[ cut here ]------------ WARNING: CPU: 0 PID: 973 at fs/sysfs/group.c:216 device_del+0x39/0x180() sysfs group ffffffff8183df40 not found for kobject 'midiC1D0' Call Trace: [<ffffffff814a3e38>] ? dump_stack+0x49/0x71 [<ffffffff8103cb72>] ? warn_slowpath_common+0x82/0xb0 [<ffffffff8103cc55>] ? warn_slowpath_fmt+0x45/0x50 [<ffffffff813521e9>] ? device_del+0x39/0x180 [<ffffffff81352339>] ? device_unregister+0x9/0x20 [<ffffffff81352384>] ? device_destroy+0x34/0x40 [<ffffffffa00ba29f>] ? snd_unregister_device+0x7f/0xd0 [snd] [<ffffffffa025124e>] ? snd_rawmidi_dev_disconnect+0xce/0x100 [snd_rawmidi] [<ffffffffa00c0192>] ? snd_device_disconnect+0x62/0x90 [snd] [<ffffffffa00c025c>] ? snd_device_disconnect_all+0x3c/0x60 [snd] [<ffffffffa00bb574>] ? snd_card_disconnect+0x124/0x1a0 [snd] [<ffffffffa02e54e8>] ? usb_audio_disconnect+0x88/0x1c0 [snd_usb_audio] [<ffffffffa015260e>] ? usb_unbind_interface+0x5e/0x1b0 [usbcore] [<ffffffff813553e9>] ? __device_release_driver+0x79/0xf0 [<ffffffff81355485>] ? device_release_driver+0x25/0x40 [<ffffffff81354e11>] ? bus_remove_device+0xf1/0x130 [<ffffffff813522b9>] ? device_del+0x109/0x180 [<ffffffffa01501d5>] ? usb_disable_device+0x95/0x1f0 [usbcore] [<ffffffffa014634f>] ? usb_disconnect+0x8f/0x190 [usbcore] [<ffffffffa0149179>] ? hub_thread+0x539/0x13a0 [usbcore] [<ffffffff810669f5>] ? sched_clock_local+0x15/0x80 [<ffffffff81066c98>] ? sched_clock_cpu+0xb8/0xd0 [<ffffffff81070730>] ? bit_waitqueue+0xb0/0xb0 [<ffffffffa0148c40>] ? usb_port_resume+0x430/0x430 [usbcore] [<ffffffffa0148c40>] ? usb_port_resume+0x430/0x430 [usbcore] [<ffffffff8105973e>] ? kthread+0xce/0xf0 [<ffffffff81059670>] ? kthread_create_on_node+0x1c0/0x1c0 [<ffffffff814a8b7c>] ? ret_from_fork+0x7c/0xb0 [<ffffffff81059670>] ? kthread_create_on_node+0x1c0/0x1c0 ---[ end trace 40b1928d1136b91e ]--- This comes from the fact that usb-audio driver may receive the disconnect callback multiple times, per each usb interface. When a device has both audio and midi interfaces, it gets called twice, and currently the driver tries to release resources at the last call. At this point, the first parent interface has been already deleted, thus deleting a child of the first parent hits such a warning. For fixing this problem, we need to call snd_card_disconnect() and cancel pending operations at the very first disconnect while the release of the whole objects waits until the last disconnect call. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=80931Reported-and-tested-by:
Tomas Gayoso <tgayoso@gmail.com> Reported-and-tested-by:
Chris J Arges <chris.j.arges@canonical.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Oliver Neukum authored
commit b45abacd upstream. The switch back is limited to ULT even on HP. The contrary finding arose by bad luck in BIOS versions for testing. This fixes spontaneous resume from S3 on some HP laptops. Signed-off-by:
Oliver Neukum <oneukum@suse.de> Signed-off-by:
-
Alan Stern authored
commit 93c9bf4d upstream. Sometimes mass-storage devices using the Bulk-only transport will mistakenly skip the data phase of a command. Rather than sending the data expected by the host or sending a zero-length packet, they go directly to the status phase and send the CSW. This causes problems for usb-storage, for obvious reasons. The driver will interpret the CSW as a short data transfer and will wait to receive a CSW. The device won't have anything left to send, so the command eventually times out. The SCSI layer doesn't retry commands after they time out (this is a relatively recent change). Therefore we should do our best to detect a skipped data phase and handle it promptly. This patch adds code to do that. If usb-storage receives a short 13-byte data transfer from the device, and if the first four bytes of the data match the CSW signature, the driver will set the residue to the full transfer length and interpret the data as a CSW. This fixes Bugzilla #86611. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net> Tested-by:
Paul Osmialowski <newchief@king.net.pl> Signed-off-by:
-
Hans de Goede authored
commit 90a646c7 upstream. This commit fixes the following oops: [10238.622067] scsi host3: uas_eh_bus_reset_handler start [10240.766164] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd [10245.779365] usb 3-4: device descriptor read/8, error -110 [10245.883331] usb 3-4: reset SuperSpeed USB device number 3 using xhci_hcd [10250.897603] usb 3-4: device descriptor read/8, error -110 [10251.058200] BUG: unable to handle kernel NULL pointer dereference at 0000000000000040 [10251.058244] IP: [<ffffffff815ac6e1>] xhci_check_streams_endpoint+0x91/0x140 <snip> [10251.059473] Call Trace: [10251.059487] [<ffffffff815aca6c>] xhci_calculate_streams_and_bitmask+0xbc/0x130 [10251.059520] [<ffffffff815aeb5f>] xhci_alloc_streams+0x10f/0x5a0 [10251.059548] [<ffffffff810a4685>] ? check_preempt_curr+0x75/0xa0 [10251.059575] [<ffffffff810a46dc>] ? ttwu_do_wakeup+0x2c/0x100 [10251.059601] [<ffffffff810a49e6>] ? ttwu_do_activate.constprop.111+0x66/0x70 [10251.059635] [<ffffffff815779ab>] usb_alloc_streams+0xab/0xf0 [10251.059662] [<ffffffffc0616b48>] uas_configure_endpoints+0x128/0x150 [uas] [10251.059694] [<ffffffffc0616bac>] uas_post_reset+0x3c/0xb0 [uas] [10251.059722] [<ffffffff815727d9>] usb_reset_device+0x1b9/0x2a0 [10251.059749] [<ffffffffc0616f42>] uas_eh_bus_reset_handler+0xb2/0x190 [uas] [10251.059781] [<ffffffff81514293>] scsi_try_bus_reset+0x53/0x110 [10251.059808] [<ffffffff815163b7>] scsi_eh_bus_reset+0xf7/0x270 <snip> The problem is the following call sequence (simplified): 1) usb_reset_device 2) usb_reset_and_verify_device 2) hub_port_init 3) hub_port_finish_reset 3) xhci_discover_or_reset_device This frees xhci->devs[slot_id]->eps[ep_index].ring for all eps but 0 4) usb_get_device_descriptor This fails 5) hub_port_init fails 6) usb_reset_and_verify_device fails, does not restore device config 7) uas_post_reset 8) xhci_alloc_streams NULL deref on the free-ed ring This commit fixes this by not allowing usb_alloc_streams to continue if the device is not configured. Note that we do allow usb_free_streams to continue after a (logical) disconnect, as it is necessary to explicitly free the streams at the xhci controller level. Signed-off-by:
-
Johan Hovold authored
commit cf84a691 upstream. Add device-id entry for GW Instek AFG-2225, which has a byte swapped bInterfaceSubClass (0x20). Reported-by:
Karl Palsson <karlp@tweak.net.au> Signed-off-by:
-
Johannes Berg authored
commit b8fff407 upstream. Upon receiving the last fragment, all but the first fragment are freed, but the multicast check for statistics at the end of the function refers to the current skb (the last fragment) causing a use-after-free bug. Since multicast frames cannot be fragmented and we check for this early in the function, just modify that check to also do the accounting to fix the issue. Reported-by:
Yosef Khyal <yosefx.khyal@intel.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Johan Hovold authored
commit e681286d upstream. Write may be called from interrupt context so make sure to use GFP_ATOMIC for all allocations in write. Fixes: 0d930e51 ("USB: opticon: Add Opticon OPN2001 write support") Signed-off-by:
-
Johan Hovold authored
commit 19125283 upstream. Write may be called from interrupt context so make sure to use GFP_ATOMIC for all allocations in write. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
-
Jan Kara authored
commit ece9c72a upstream. Priority of a merged request is computed by ioprio_best(). If one of the requests has undefined priority (IOPRIO_CLASS_NONE) and another request has priority from IOPRIO_CLASS_BE, the function will return the undefined priority which is wrong. Fix the function to properly return priority of a request with the defined priority. Fixes: d58cdfb8Signed-off-by:
Jan Kara <jack@suse.cz> Reviewed-by:
Jeff Moyer <jmoyer@redhat.com> Signed-off-by:
Jens Axboe <axboe@fb.com> [bwh: Backported to 3.2: adjust filename] Signed-off-by:
-
Sinclair Yeh authored
commit 9a72384d upstream. When screen objects are enabled, the bpp is assumed to be 32, otherwise it is set to 16. v2: * Use u32 instead of u64 for assumed_bpp. * Fixed mechanism to check for screen objects * Limit the back buffer size to VRAM. Signed-off-by:
Sinclair Yeh <syeh@vmware.com> Reviewed-by:
Thomas Hellstrom <thellstrom@vmware.com> [bwh: Backported to 3.2: drop changes for dev_priv->prim_bb_mem] Signed-off-by:
-
Rabin Vincent authored
commit 086ba77a upstream. ARM has some private syscalls (for example, set_tls(2)) which lie outside the range of NR_syscalls. If any of these are called while syscall tracing is being performed, out-of-bounds array access will occur in the ftrace and perf sys_{enter,exit} handlers. # trace-cmd record -e raw_syscalls:* true && trace-cmd report ... true-653 [000] 384.675777: sys_enter: NR 192 (0, 1000, 3, 4000022, ffffffff, 0) true-653 [000] 384.675812: sys_exit: NR 192 = 1995915264 true-653 [000] 384.675971: sys_enter: NR 983045 (76f74480, 76f74000, 76f74b28, 76f74480, 76f76f74, 1) true-653 [000] 384.675988: sys_exit: NR 983045 = 0 ... # trace-cmd record -e syscalls:* true [ 17.289329] Unable to handle kernel paging request at virtual address aaaaaace [ 17.289590] pgd = 9e71c000 [ 17.289696] [aaaaaace] *pgd=00000000 [ 17.289985] Internal error: Oops: 5 [#1] PREEMPT SMP ARM [ 17.290169] Modules linked in: [ 17.290391] CPU: 0 PID: 704 Comm: true Not tainted 3.18.0-rc2+ #21 [ 17.290585] task: 9f4dab00 ti: 9e710000 task.ti: 9e710000 [ 17.290747] PC is at ftrace_syscall_enter+0x48/0x1f8 [ 17.290866] LR is at syscall_trace_enter+0x124/0x184 Fix this by ignoring out-of-NR_syscalls-bounds syscall numbers. Commit cd0980fc "tracing: Check invalid syscall nr while tracing syscalls" added the check for less than zero, but it should have also checked for greater than NR_syscalls. Link: http://lkml.kernel.org/p/1414620418-29472-1-git-send-email-rabin@rab.in Fixes: cd0980fc "tracing: Check invalid syscall nr while tracing syscalls" Signed-off-by:
Rabin Vincent <rabin@rab.in> Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Will Deacon authored
commit 60916a93 upstream. syscall_get_nr can return -1 in the case that the task is not executing a system call. This patch fixes perf_syscall_{enter,exit} to check that the syscall number is valid before using it as an index into a bitmap. Link: http://lkml.kernel.org/r/1345137254-7377-1-git-send-email-will.deacon@arm.com Cc: Jason Baron <jbaron@redhat.com> Cc: Wade Farnsworth <wade_farnsworth@mentor.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
-
Cyril Brulebois authored
commit 664d6a79 upstream. 0x1b75 0xa200 AirLive WN-200USB wireless 11b/g/n dongle References: https://bugs.debian.org/766802Reported-by:
Martin Mokrejs <mmokrejs@fold.natur.cuni.cz> Signed-off-by:
Cyril Brulebois <kibi@debian.org> Acked-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com> Signed-off-by:
-
Ulrich Eckhardt authored
commit 8c5bcded upstream. The Tevii S480 outputs 18V on startup for the LNB supply voltage and does not automatically power down. This blocks other receivers connected to a satellite channel router (EN50494), since the receivers can not send the required DiSEqC sequences when the Tevii card is connected to a the same SCR. This patch switches off the LNB supply voltage on initialization of the frontend. [mchehab@osg.samsung.com: add a comment about why we're explicitly turning off voltage at device init] Signed-off-by:
Ulrich Eckhardt <uli@uli-eckhardt.de> Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com> [bwh: Backported to 3.2: adjust filename] Signed-off-by:
-
Jan Kara authored
commit 6050d47a upstream. When ext4_handle_dirty_dx_node() or ext4_handle_dirty_dirent_node() fail, there's really something wrong with the fs and there's no point in continuing further. Just return error from make_indexed_dir() in that case. Also initialize frames array so that if we return early due to error, dx_release() doesn't try to dereference uninitialized memory (which could happen also due to error in do_split()). Coverity-id: 741300 Signed-off-by:
Theodore Ts'o <tytso@mit.edu> [bwh: Backported to 3.2: - We have ext4_handle_dirty_metadata() not ext4_handle_dirty_{dx,dirent}_node()] - do_split() returns errors by reference not with ERR_PTR()] Signed-off-by:
-
Jan Kara authored
commit 599a9b77 upstream. When we fail to load block bitmap in __ext4_new_inode() we will dereference NULL pointer in ext4_journal_get_write_access(). So check for error from ext4_read_block_bitmap(). Coverity-id: 989065 Signed-off-by:
-
Jan Kara authored
commit 9378c676 upstream. When there are no meta block groups update_backups() will compute the backup block in 32-bit arithmetics thus possibly overflowing the block number and corrupting the filesystem. OTOH filesystems without meta block groups larger than 16 TB should be rare. Fix the problem by doing the counting in 64-bit arithmetics. Coverity-id: 741252 Signed-off-by:
Lukas Czerner <lczerner@redhat.com> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Johannes Berg authored
commit 46238845 upstream. When an interface is deleted, an ongoing hardware scan is canceled and the driver must abort the scan, at the very least reporting completion while the interface is removed. However, if it scheduled the work that might only run after everything is said and done, which leads to cfg80211 warning that the scan isn't reported as finished yet; this is no fault of the driver, it already did, but mac80211 hasn't processed it. To fix this situation, flush the delayed work when the interface being removed is the one that was executing the scan. Reported-by:
Sujith Manoharan <sujith@msujith.org> Tested-by:
-
Jan Kara authored
commit ea5d05b3 upstream. If __bitmap_shift_left() or __bitmap_shift_right() are asked to shift by a multiple of BITS_PER_LONG, they will try to shift a long value by BITS_PER_LONG bits which is undefined. Change the functions to avoid the undefined shift. Coverity id: 1192175 Coverity id: 1192174 Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
David Rientjes authored
commit 6d50e60c upstream. If an anonymous mapping is not allowed to fault thp memory and then madvise(MADV_HUGEPAGE) is used after fault, khugepaged will never collapse this memory into thp memory. This occurs because the madvise(2) handler for thp, hugepage_madvise(), clears VM_NOHUGEPAGE on the stack and it isn't stored in vma->vm_flags until the final action of madvise_behavior(). This causes the khugepaged_enter_vma_merge() to be a no-op in hugepage_madvise() when the vma had previously had VM_NOHUGEPAGE set. Fix this by passing the correct vma flags to the khugepaged mm slot handler. There's no chance khugepaged can run on this vma until after madvise_behavior() returns since we hold mm->mmap_sem. It would be possible to clear VM_NOHUGEPAGE directly from vma->vm_flags in hugepage_advise(), but I didn't want to introduce special case behavior into madvise_behavior(). I think it's best to just let it always set vma->vm_flags itself. Signed-off-by:
David Rientjes <rientjes@google.com> Reported-by:
Suleiman Souhlal <suleiman@google.com> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Cc: Andrea Arcangeli <aarcange@redhat.com> Signed-off-by:
-
Wang Nan authored
commit 401507d6 upstream. Commit ff7ee93f ("cgroup/kmemleak: Annotate alloc_page() for cgroup allocations") introduces kmemleak_alloc() for alloc_page_cgroup(), but corresponding kmemleak_free() is missing, which makes kmemleak be wrongly disabled after memory offlining. Log is pasted at the end of this commit message. This patch add kmemleak_free() into free_page_cgroup(). During page offlining, this patch removes corresponding entries in kmemleak rbtree. After that, the freed memory can be allocated again by other subsystems without killing kmemleak. bash # for x in 1 2 3 4; do echo offline > /sys/devices/system/memory/memory$x/state ; sleep 1; done ; dmesg | grep leak Offlined Pages 32768 kmemleak: Cannot insert 0xffff880016969000 into the object search tree (overlaps existing) CPU: 0 PID: 412 Comm: sleep Not tainted 3.17.0-rc5+ #86 Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 Call Trace: dump_stack+0x46/0x58 create_object+0x266/0x2c0 kmemleak_alloc+0x26/0x50 kmem_cache_alloc+0xd3/0x160 __sigqueue_alloc+0x49/0xd0 __send_signal+0xcb/0x410 send_signal+0x45/0x90 __group_send_sig_info+0x13/0x20 do_notify_parent+0x1bb/0x260 do_exit+0x767/0xa40 do_group_exit+0x44/0xa0 SyS_exit_group+0x17/0x20 system_call_fastpath+0x16/0x1b kmemleak: Kernel memory leak detector disabled kmemleak: Object 0xffff880016900000 (size 524288): kmemleak: comm "swapper/0", pid 0, jiffies 4294667296 kmemleak: min_count = 0 kmemleak: count = 0 kmemleak: flags = 0x1 kmemleak: checksum = 0 kmemleak: backtrace: log_early+0x63/0x77 kmemleak_alloc+0x4b/0x50 init_section_page_cgroup+0x7f/0xf5 page_cgroup_init+0xc5/0xd0 start_kernel+0x333/0x408 x86_64_start_reservations+0x2a/0x2c x86_64_start_kernel+0xf5/0xfc Fixes: ff7ee93f (cgroup/kmemleak: Annotate alloc_page() for cgroup allocations) Signed-off-by:
Wang Nan <wangnan0@huawei.com> Acked-by:
Johannes Weiner <hannes@cmpxchg.org> Acked-by:
Michal Hocko <mhocko@suse.cz> Cc: Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
Kuninori Morimoto authored
commit c1b9b9b1 upstream. FSI doesn't support PAUSE. Remove SNDRV_PCM_INFO_PAUSE flags from snd_pcm_hardware info Signed-off-by:
Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Signed-off-by:
-
Will Deacon authored
commit ce9ec37b upstream. When unmapping a range of pages in zap_pte_range, the page being unmapped is added to an mmu_gather_batch structure for asynchronous freeing. If we run out of space in the batch structure before the range has been completely unmapped, then we break out of the loop, force a TLB flush and free the pages that we have batched so far. If there are further pages to unmap, then we resume the loop where we left off. Unfortunately, we forget to update addr when we break out of the loop, which causes us to truncate the range being invalidated as the end address is exclusive. When we re-enter the loop at the same address, the page has already been freed and the pte_present test will fail, meaning that we do not reconsider the address for invalidation. This patch fixes the problem by incrementing addr by the PAGE_SIZE before breaking out of the loop on batch failure. Signed-off-by:
-
Alex Deucher authored
commit 8c3e4347 upstream. 0x4c6e is a secondary device id so should not be used by the driver. Noticed-by:
Mark Kettenis <mark.kettenis@xs4all.nl> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Dmitry Kasatkin authored
commit 3b1deef6 upstream. evm_inode_setxattr() can be called with no value. The function does not check the length so that following command can be used to produce the kernel oops: setfattr -n security.evm FOO. This patch fixes it. Changes in v3: * there is no reason to return different error codes for EVM_XATTR_HMAC and non EVM_XATTR_HMAC. Remove unnecessary test then. Changes in v2: * testing for validity of xattr type [ 1106.396921] BUG: unable to handle kernel NULL pointer dereference at (null) [ 1106.398192] IP: [<ffffffff812af7b8>] evm_inode_setxattr+0x2a/0x48 [ 1106.399244] PGD 29048067 PUD 290d7067 PMD 0 [ 1106.399953] Oops: 0000 [#1] SMP [ 1106.400020] Modules linked in: bridge stp llc evdev serio_raw i2c_piix4 button fuse [ 1106.400020] CPU: 0 PID: 3635 Comm: setxattr Not tainted 3.16.0-kds+ #2936 [ 1106.400020] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011 [ 1106.400020] task: ffff8800291a0000 ti: ffff88002917c000 task.ti: ffff88002917c000 [ 1106.400020] RIP: 0010:[<ffffffff812af7b8>] [<ffffffff812af7b8>] evm_inode_setxattr+0x2a/0x48 [ 1106.400020] RSP: 0018:ffff88002917fd50 EFLAGS: 00010246 [ 1106.400020] RAX: 0000000000000000 RBX: ffff88002917fdf8 RCX: 0000000000000000 [ 1106.400020] RDX: 0000000000000000 RSI: ffffffff818136d3 RDI: ffff88002917fdf8 [ 1106.400020] RBP: ffff88002917fd68 R08: 0000000000000000 R09: 00000000003ec1df [ 1106.400020] R10: 0000000000000000 R11: 0000000000000000 R12: ffff8800438a0a00 [ 1106.400020] R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000 [ 1106.400020] FS: 00007f7dfa7d7740(0000) GS:ffff88005da00000(0000) knlGS:0000000000000000 [ 1106.400020] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 1106.400020] CR2: 0000000000000000 CR3: 000000003763e000 CR4: 00000000000006f0 [ 1106.400020] Stack: [ 1106.400020] ffff8800438a0a00 ffff88002917fdf8 0000000000000000 ffff88002917fd98 [ 1106.400020] ffffffff812a1030 ffff8800438a0a00 ffff88002917fdf8 0000000000000000 [ 1106.400020] 0000000000000000 ffff88002917fde0 ffffffff8116d08a ffff88002917fdc8 [ 1106.400020] Call Trace: [ 1106.400020] [<ffffffff812a1030>] security_inode_setxattr+0x5d/0x6a [ 1106.400020] [<ffffffff8116d08a>] vfs_setxattr+0x6b/0x9f [ 1106.400020] [<ffffffff8116d1e0>] setxattr+0x122/0x16c [ 1106.400020] [<ffffffff811687e8>] ? mnt_want_write+0x21/0x45 [ 1106.400020] [<ffffffff8114d011>] ? __sb_start_write+0x10f/0x143 [ 1106.400020] [<ffffffff811687e8>] ? mnt_want_write+0x21/0x45 [ 1106.400020] [<ffffffff811687c0>] ? __mnt_want_write+0x48/0x4f [ 1106.400020] [<ffffffff8116d3e6>] SyS_setxattr+0x6e/0xb0 [ 1106.400020] [<ffffffff81529da9>] system_call_fastpath+0x16/0x1b [ 1106.400020] Code: c3 0f 1f 44 00 00 55 48 89 e5 41 55 49 89 d5 41 54 49 89 fc 53 48 89 f3 48 c7 c6 d3 36 81 81 48 89 df e8 18 22 04 00 85 c0 75 07 <41> 80 7d 00 02 74 0d 48 89 de 4c 89 e7 e8 5a fe ff ff eb 03 83 [ 1106.400020] RIP [<ffffffff812af7b8>] evm_inode_setxattr+0x2a/0x48 [ 1106.400020] RSP <ffff88002917fd50> [ 1106.400020] CR2: 0000000000000000 [ 1106.428061] ---[ end trace ae08331628ba3050 ]--- Reported-by:
Dmitry Kasatkin <d.kasatkin@samsung.com> Signed-off-by:
Mimi Zohar <zohar@linux.vnet.ibm.com> Signed-off-by:
-
Takashi Iwai authored
commit 317168d0 upstream. In compat mode, we copy each field of snd_pcm_status struct but don't touch the reserved fields, and this leaves uninitialized values there. Meanwhile the native ioctl does zero-clear the whole structure, so we should follow the same rule in compat mode, too. Reported-by:
Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by:
-
Imre Deak authored
commit 94fb823f upstream. If a device's dev_pm_ops::freeze callback fails during the QUIESCE phase, we don't rollback things correctly calling the thaw and complete callbacks. This could leave some devices in a suspended state in case of an error during resuming from hibernation. Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
James Ralston authored
commit 690000b9 upstream. This patch adds the AHCI-mode SATA Device IDs for the Intel Sunrise Point PCH. Signed-off-by:
James Ralston <james.d.ralston@intel.com> Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Tejun Heo authored
commit 66a7cbc3 upstream. Samsung pci-e SSDs on macbooks failed miserably on NCQ commands, so 67809f85 ("ahci: disable NCQ on Samsung pci-e SSDs on macbooks") disabled NCQ on them. It turns out that NCQ is fine as long as MSI is not used, so let's turn off MSI and leave NCQ on. Signed-off-by:
Imre Kaloz <kaloz@openwrt.org> Fixes: 67809f85 ("ahci: disable NCQ on Samsung pci-e SSDs on macbooks") Signed-off-by:
-
Brian Silverman authored
commit 30a6b803 upstream. free_pi_state and exit_pi_state_list both clean up futex_pi_state's. exit_pi_state_list takes the hb lock first, and most callers of free_pi_state do too. requeue_pi doesn't, which means free_pi_state can free the pi_state out from under exit_pi_state_list. For example: task A | task B exit_pi_state_list | pi_state = | curr->pi_state_list->next | | futex_requeue(requeue_pi=1) | // pi_state is the same as | // the one in task A | free_pi_state(pi_state) | list_del_init(&pi_state->list) | kfree(pi_state) list_del_init(&pi_state->list) | Move the free_pi_state calls in requeue_pi to before it drops the hb locks which it's already holding. [ tglx: Removed a pointless free_pi_state() call and the hb->lock held debugging. The latter comes via a seperate patch ] Signed-off-by:
Brian Silverman <bsilver16384@gmail.com> Cc: austin.linux@gmail.com Cc: darren@dvhart.com Cc: peterz@infradead.org Link: http://lkml.kernel.org/r/1414282837-23092-1-git-send-email-bsilver16384@gmail.comSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Mathias Krause authored
commit 6891c450 upstream. If userland creates a timer without specifying a sigevent info, we'll create one ourself, using a stack local variable. Particularly will we use the timer ID as sival_int. But as sigev_value is a union containing a pointer and an int, that assignment will only partially initialize sigev_value on systems where the size of a pointer is bigger than the size of an int. On such systems we'll copy the uninitialized stack bytes from the timer_create() call to userland when the timer actually fires and we're going to deliver the signal. Initialize sigev_value with 0 to plug the stack info leak. Found in the PaX patch, written by the PaX Team. Fixes: 5a9fa730 ("posix-timers: kill ->it_sigev_signo and...") Signed-off-by:
Mathias Krause <minipli@googlemail.com> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Brad Spengler <spender@grsecurity.net> Cc: PaX Team <pageexec@freemail.hu> Link: http://lkml.kernel.org/r/1412456799-32339-1-git-send-email-minipli@googlemail.comSigned-off-by:
-
Hans de Goede authored
commit 993b3a3f upstream. These models need i8042.notimeout, otherwise the touchpad will not work. BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=69731 BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1111138Signed-off-by:
-
Quentin Casasnovas authored
commit 3d32e4db upstream. The third parameter of kvm_unpin_pages() when called from kvm_iommu_map_pages() is wrong, it should be the number of pages to un-pin and not the page size. This error was facilitated with an inconsistent API: kvm_pin_pages() takes a size, but kvn_unpin_pages() takes a number of pages, so fix the problem by matching the two. This was introduced by commit 350b8bdd ("kvm: iommu: fix the third parameter of kvm_iommu_put_pages (CVE-2014-3601)"), which fixes the lack of un-pinning for pages intended to be un-pinned (i.e. memory leak) but unfortunately potentially aggravated the number of pages we un-pin that should have stayed pinned. As far as I understand though, the same practical mitigations apply. This issue was found during review of Red Hat 6.6 patches to prepare Ksplice rebootless updates. Thanks to Vegard for his time on a late Friday evening to help me in understanding this code. Fixes: 350b8bdd ("kvm: iommu: fix the third parameter of... (CVE-2014-3601)") Cc: stable@vger.kernel.org Signed-off-by:
Quentin Casasnovas <quentin.casasnovas@oracle.com> Signed-off-by:
Vegard Nossum <vegard.nossum@oracle.com> Signed-off-by:
Jamie Iles <jamie.iles@oracle.com> Reviewed-by:
Sasha Levin <sasha.levin@oracle.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> [bwh: Backported to 3.2: kvm_pin_pages() also takes a struct kvm *kvm param] Signed-off-by:
-
