- 07 Jul, 2011 10 commits
-
-
Fabio Estevam authored
Fix the following warning: CC arch/arm/plat-mxc/iomux-v1.o arch/arm/plat-mxc/iomux-v1.c: In function 'mxc_gpio_setup_multiple_pins': arch/arm/plat-mxc/iomux-v1.c:160: warning: 'ret' may be used uninitialized in this function arch/arm/plat-mxc/iomux-v1.c:160: note: 'ret' was declared here Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Fabio Estevam authored
Fix the 2.8V (VMMC1) and 1.8V (VGEN) voltage generation on mx27_3ds. Also configure the IOMUX for the PMIC interrupt pin and for the CSPI chip select that is connected to the MC13783 PMIC. In order to get the voltage for the LCD (2.8V and 1.8V) it is also necessary to turn on GPO1 and GPO3 supplies because they are connected to switches that enable these two voltages. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Fabio Estevam authored
When setting the IOMUX of multiple pins via mxc_gpio_setup_multiple_pins, gpio_request is called and this prevents subsequent calls of gpio_request done by drivers to succeed. Remove gpio_request call from mxc_gpio_setup_multiple_pins function. As gpio_request is removed from mxc_gpio_setup_multiple_pins, there is no need to have mxc_gpio_release_multiple_pins anymore, so remove this function. Tested on a mx27_3ds board and after applying this patch it is possible to define all the IOMUX setup in a static array Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Fabio Estevam authored
Original code was assuming that the CSPI1 pins on the MX31PDK were the primary pin function, which is incorrect. On MX31PDK board these are the pins that provide CSPI1 functionality: DSR_DCE1 (ALT mode 1) --> CSPI1_CLK RI_DCE1 (ALT mode 1) --> CSPI1_RDY DTR_DTE1 -->CSI1_MOSI DSR_DTE1 --> CSPI1_MISO DTR_DCE2 ---> CSPI1_SS2 The 3 IOMUX settings above are done via GPR as per Table A-1 of the MX31RM. This patch fixes the CSPI1 IOMUX and makes the LCD to be functional. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Fabio Estevam authored
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Marc Kleine-Budde authored
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Fabio Estevam authored
MX53 has 4 chip selects (CS0 - CS3) and the valid combinations are: - CS0 (128MB) - CS0 (64MB), CS1 (64MB) - CS0 (64MB), CS1 (32MB), CS2 (32MB) - CS0 (32MB), CS1 (32MB), CS2 (32MB) , CS3 (32MB) Fix these addresses and also take into account all the four possibilities. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Fabio Estevam authored
MX53_PAD_PATA_DATA6 can have the following alternate modes: PATA_DATA_6: mode 0 GPIO2_6: mode 1 EMI_NANDF_D_6: mode 3 ESDHC4_DAT6 mode 4 GPU3d_GPU_DEBUG_OUT_6 mode 5 IPU_DIAG_BUS_6 mode 6 Fix the modes accordingly. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Dinh Nguyen <dinh.nguyen@freescale.com> Acked-by: Olof Johansson <olof@lixom.net> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Fabio Estevam authored
Let USB Storage be built by default. Also select NLS_ISO8859 so that the USB device can be mounted. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
Shawn Guo authored
The patch fixes the warning below. arch/arm/configs/mxs_defconfig:92:warning: symbol value 'm' invalid for RTC_CLASS Signed-off-by: Shawn Guo <shawn.guo@linaro.org> Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
-
- 21 Jun, 2011 7 commits
-
-
Linus Torvalds authored
-
Linus Torvalds authored
Commit 13e12d14 ("vfs: reorganize 'struct inode' layout a bit") moved things around a bit changed i_state to be unsigned int instead of unsigned long. That was to help structure layout for the 64-bit case, and shrink 'struct inode' a bit (admittedly that only happened when spinlock debugging was on and i_flags didn't pack with i_lock). However, Meelis Roos reports that this results in unaligned exceptions on sprc, and it turns out that the bit-locking primitives that we use for the I_NEW bit want to use the bitops. Which want 'unsigned long', not 'unsigned int'. We really should fix the bit locking code to not have that kind of requirement, but that's a much bigger change. So for now, revert that field back to 'unsigned long' (but keep the other re-ordering changes from the commit that caused this). Andi points out that we have played games with this in 'struct page', so it's solvable with other hacks too, but since right now the struct inode size advantage only happens with some rare config options, it's not worth fighting. It _would_ be worth fixing the bitlocking code, though. Especially since there is no type safety in the bitlocking code (this never caused any warnings, and worked fine on x86-64, because the bitlocks take a 'void *' and x86-64 doesn't care that deeply about alignment). So it's currently a very easy problem to trigger by mistake and never notice. Reported-by: Meelis Roos <mroos@linux.ee> Cc: Andi Kleen <andi@firstfloor.org> Cc: David Miller <davem@davemloft.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6Linus Torvalds authored
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: drm/radeon/kms/r6xx+: voltage fixes drm/nouveau: drop leftover debugging drm/radeon: avoid warnings from r600/eg irq handlers on powered off card. drm/radeon/kms: add missing param for dce3.2 DP transmitter setup drm/radeon/kms/atom: fix duallink on some early DCE3.2 cards drm/nouveau: fix assumption that semaphore dmaobj is valid in x-chan sync drm/nv50/disp: fix gamma with page flipping overlay turned on drm/nouveau/pm: Prevent overflow in nouveau_perf_init() drm/nouveau: fix big-endian switch
-
git://codeaurora.org/quic/kernel/davidb/linux-msmLinus Torvalds authored
* 'msm-fix' of git://codeaurora.org/quic/kernel/davidb/linux-msm: msm: timer: Fix DGT rate on 8960 and 8660 msm: timer: compensate for timer shift in msm_read_timer_count msm: timer: Fix SMP build error
-
git://linux-nfs.org/~bfields/linuxLinus Torvalds authored
* 'for-2.6.40' of git://linux-nfs.org/~bfields/linux: nfsd4: fix break_lease flags on nfsd open nfsd: link returns nfserr_delay when breaking lease nfsd: v4 support requires CRYPTO nfsd: fix dependency of nfsd on auth_rpcgss
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds authored
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (40 commits) pxa168_eth: fix race in transmit path. ipv4, ping: Remove duplicate icmp.h include netxen: fix race in skb->len access sgi-xp: fix a use after free hp100: fix an skb->len race netpoll: copy dev name of slaves to struct netpoll ipv4: fix multicast losses r8169: fix static initializers. inet_diag: fix inet_diag_bc_audit() gigaset: call module_put before restart of if_open() farsync: add module_put to error path in fst_open() net: rfs: enable RFS before first data packet is received fs_enet: fix freescale FCC ethernet dp buffer alignment netdev: bfin_mac: fix memory leak when freeing dma descriptors vlan: don't call ndo_vlan_rx_register on hardware that doesn't have vlan support caif: Bugfix - XOFF removed channel from caif-mux tun: teach the tun/tap driver to support netpoll dp83640: drop PHY status frames in the driver. dp83640: fix phy status frame event parsing phylib: Allow BCM63XX PHY to be selected only on BCM63XX. ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6Linus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: devcgroup_inode_permission: take "is it a device node" checks to inlined wrapper fix comment in generic_permission() kill obsolete comment for follow_down() proc_sys_permission() is OK in RCU mode reiserfs_permission() doesn't need to bail out in RCU mode proc_fd_permission() is doesn't need to bail out in RCU mode nilfs2_permission() doesn't need to bail out in RCU mode logfs doesn't need ->permission() at all coda_ioctl_permission() is safe in RCU mode cifs_permission() doesn't need to bail out in RCU mode bad_inode_permission() is safe from RCU mode ubifs: dereferencing an ERR_PTR in ubifs_mount()
-
- 20 Jun, 2011 23 commits
-
-
Alex Deucher authored
0xff01 is not an actual voltage value, but a flag for the driver. If the power state as that value, skip setting the voltage. Signed-off-by: Alex Deucher <alexdeucher@gmail.com> Signed-off-by: Dave Airlie <airlied@redhat.com>
-
Stephen Boyd authored
The DGT runs at 27 MHz divided by 4 on 8660 and 8960. Signed-off-by: Stephen Boyd <sboyd@codeaurora.org> Signed-off-by: David Brown <davidb@codeaurora.org>
-
Richard Cochran authored
Because the socket buffer is freed in the completion interrupt, it is not safe to access it after submitting it to the hardware. Cc: stable@kernel.org Cc: Sachin Sanap <ssanap@marvell.com> Cc: Zhangfei Gao <zgao6@marvell.com> Cc: Philip Rakity <prakity@marvell.com> Signed-off-by: Richard Cochran <richard.cochran@omicron.at> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Jesper Juhl authored
Remove the duplicate inclusion of net/icmp.h from net/ipv4/ping.c Signed-off-by: Jesper Juhl <jj@chaosbits.net> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Eric Dumazet authored
As soon as skb is given to hardware, TX completion can free skb under us. Therefore, we should update dev stats before kicking the device. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> CC: Amit Kumar Salecha <amit.salecha@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xenLinus Torvalds authored
* 'stable/bug.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen: xen/setup: Fix for incorrect xen_extra_mem_start. xen: When calling power_off, don't call the halt function. xen: Fix compile warning when CONFIG_SMP is not defined. xen: support CONFIG_MAXSMP xen: partially revert "xen: set max_pfn_mapped to the last pfn mapped"
-
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/inputLinus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: sh_keysc - 8x8 MODE_6 fix Input: omap-keypad - add missing input_sync() Input: evdev - try to wake up readers only if we have full packet Input: properly assign return value of clamp() macro.
-
git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstableLinus Torvalds authored
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable: Btrfs: avoid delayed metadata items during commits btrfs: fix uninitialized return value btrfs: fix wrong reservation when doing delayed inode operations btrfs: Remove unused sysfs code btrfs: fix dereference of ERR_PTR value Btrfs: fix relocation races Btrfs: set no_trans_join after trying to expand the transaction Btrfs: protect the pending_snapshots list with trans_lock Btrfs: fix path leakage on subvol deletion Btrfs: drop the delalloc_bytes check in shrink_delalloc Btrfs: check the return value from set_anon_super
-
git://git.kernel.org/pub/scm/virt/kvm/kvmLinus Torvalds authored
* 'kvm-updates/3.0' of git://git.kernel.org/pub/scm/virt/kvm/kvm: KVM: Fix register corruption in pvclock_scale_delta KVM: MMU: fix opposite condition in mapping_level_dirty_bitmap KVM: VMX: do not overwrite uptodate vcpu->arch.cr3 on KVM_SET_SREGS KVM: MMU: Fix build warnings in walk_addr_generic()
-
Al Viro authored
inode_permission() calls devcgroup_inode_permission() and almost all such calls are _not_ for device nodes; let's at least keep the common path straight... Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-
Al Viro authored
CAP_DAC_OVERRIDE is enough for MAY_EXEC on directory, even if no exec bits are set. Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-
Al Viro authored
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-
Al Viro authored
nothing blocking there, since all instances of sysctl ->permissions() method are non-blocking - both of them, that is. Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-
Al Viro authored
nothing blocking other than generic_permission() (and check_acl callback does bail out in RCU mode). Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-
Al Viro authored
nothing blocking except generic_permission() Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-
Al Viro authored
Nothing blocking except for generic_permission(). Which will DTRT. Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-
Al Viro authored
... and never did, what with its ->permission() being what we do by default when ->permission is NULL... Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-
Al Viro authored
return (mask & MAY_EXEC) ? -EACCES : 0; is non-blocking... Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-
Al Viro authored
nothing potentially blocking except generic_permission(), which will DTRT Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-
Al Viro authored
return -EIO; is *not* a blocking operation, thank you very much. Nick, what the hell have you been smoking? Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-
Dan Carpenter authored
d251ed27 "ubifs: fix sget races" left out the goto from this error path so the static checkers complain that we're dereferencing "sb" when it's an ERR_PTR. Signed-off-by: Dan Carpenter <error27@gmail.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-
J. Bruce Fields authored
Thanks to Casey Bodley for pointing out that on a read open we pass 0, instead of O_RDONLY, to break_lease, with the result that a read open is treated like a write open for the purposes of lease breaking! Reported-by: Casey Bodley <cbodley@citi.umich.edu> Cc: stable@kernel.org Signed-off-by: J. Bruce Fields <bfields@redhat.com>
-
Dave Airlie authored
this printk isn't really useful, just drop it for now. Signed-off-by: Dave Airlie <airlied@redhat.com>
-