Pull powerpc fixes from Ben Herrenschmidt:
 "A bit more endian problems found during testing of 3.13 and a few
  other simple fixes and regressions fixes"

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc: Fix alignment of secondary cpu spin vars
  powerpc: Align p_end
  powernv/eeh: Add buffer for P7IOC hub error data
  powernv/eeh: Fix possible buffer overrun in ioda_eeh_phb_diag()
  powerpc: Make 64-bit non-VMX __copy_tofrom_user bi-endian
  powerpc: Make unaligned accesses endian-safe for powerpc
  powerpc: Fix bad stack check in exception entry
  powerpc/512x: dts: disable MPC5125 usb module
  powerpc/512x: dts: remove misplaced IRQ spec from 'soc' node (5125)

Pull networking fixes from David Miller:
 "Some holiday bug fixes for 3.13...  There is still one bug I'd like to
  get fixed before 3.13-final.

  The vlan code erroneously assignes the header ops of the underlying
  real device to the VLAN device above it when the real device can
  hardware offload VLAN handling.  That's completely bogus because
  header ops are tied to the device type, so they only expect to see a
  'dev' argument compatible with their ops.

  The fix is the have the VLAN code use a special set of header ops that
  does the pass-thru correctly, by calling the underlying real device's
  header ops but _also_ passing in the real device instead of the VLAN
  device.

  That fix is currently waiting some testing.

  Anyways, of note here:

   1) Fix bitmap edge case in radiotap, from Johannes Berg.

   2) Fix oops on driver unload in rtlwifi, from Larry Finger.

   3) Bonding doesn't do locking correctly during speed/duplex/link
      changes, from Ding Tianhong.

   4) Fix header parsing in GRE code, this bug has been around for a few
      releases.  From Timo Teräs.

   5) SIT tunnel driver MTU check needs to take GSO into account, from
      Eric Dumazet.

   6) Minor info leak in inet_diag, from Daniel Borkmann.

   7) Info leak in YAM hamradio driver, from Salva Peiró.

   8) Fix route expiration state handling in ipv6 routing code, from Li
      RongQing.

   9) DCCP probe module does not check request_module()'s return value,
      from Wang Weidong.

  10) cpsw driver passes NULL device names to request_irq(), from
      Mugunthan V N.

  11) Prevent a NULL splat in RDS binding code, from Sasha Levin.

  12) Fix 4G overflow test in tg3 driver, from Nithin Sujir.

  13) Cure use after free in arc_emac and fec driver's software
      timestamp handling, from Eric Dumazet.

  14) SIT driver can fail to release the route when
      iptunnel_handle_offloads() throws an error.  From Li RongQing.

  15) Several batman-adv fixes from Simon Wunderlich and Antonio
      Quartulli.

  16) Fix deadlock during TIPC socket release, from Ying Xue.

  17) Fix regression in ROSE protocol recvmsg() msg_name handling, from
      Florian Westphal.

  18) stmmac PTP support releases wrong spinlock, from Vince Bridgers"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (73 commits)
  stmmac: Fix incorrect spinlock release and PTP cap detection.
  phy: IRQ cannot be shared
  net: rose: restore old recvmsg behavior
  xen-netback: fix guest-receive-side array sizes
  fec: Do not assume that PHY reset is active low
  tipc: fix deadlock during socket release
  netfilter: nf_tables: fix wrong datatype in nft_validate_data_load()
  batman-adv: fix vlan header access
  batman-adv: clean nf state when removing protocol header
  batman-adv: fix alignment for batadv_tvlv_tt_change
  batman-adv: fix size of batadv_bla_claim_dst
  batman-adv: fix size of batadv_icmp_header
  batman-adv: fix header alignment by unrolling batadv_header
  batman-adv: fix alignment for batadv_coded_packet
  netfilter: nf_tables: fix oops when updating table with user chains
  netfilter: nf_tables: fix dumping with large number of sets
  ipv6: release dst properly in ipip6_tunnel_xmit
  netxen: Correct off-by-one errors in bounds checks
  net: Add some clarification to skb_tx_timestamp() comment.
  arc_emac: fix potential use after free
  ...

Anatolij writes:

Please pull two DTS fixes for MPC5125 tower board. Without
them the v3.13-rcX kernels do not boot.

This patch corrects a problem in stmmac_ptp.c, functions
stmmac_adjust_time and stmmac_adjust_freq where the incorrect spinlocks
were released. This patch also addresses a problem in stmmac_main,
function stmmac_init_ptp where the capability detection for
advanced timestamping was masked by message masking.

This patch was touch tested using linuxptp, and runs without the previously
observed instabilities. More extensive testing is ongoing.

Vince
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With the way PHY IRQ handler is implemented (all real handling being pushed to
the workqueue and returning IRQ_HANDLED all the time PHY is active), we cannot
really claim that PHY IRQ can be shared when calling request_irq().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

recvmsg handler in net/rose/af_rose.c performs size-check ->msg_namelen.

After commit f3d33426
(net: rework recvmsg handler msg_name and msg_namelen logic), we now
always take the else branch due to namelen being initialized to 0.

Digging in netdev-vger-cvs git repo shows that msg_namelen was
initialized with a fixed-size since at least 1995, so the else branch
was never taken.

Compile tested only.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The sizes chosen for the metadata and grant_copy_op arrays on the guest
receive size are wrong;

- The meta array is needlessly twice the ring size, when we only ever
  consume a single array element per RX ring slot
- The grant_copy_op array is way too small. It's sized based on a bogus
  assumption: that at most two copy ops will be used per ring slot. This
  may have been true at some point in the past but it's clear from looking
  at start_new_rx_buffer() that a new ring slot is only consumed if a frag
  would overflow the current slot (plus some other conditions) so the actual
  limit is MAX_SKB_FRAGS grant_copy_ops per ring slot.

This patch fixes those two sizing issues and, because grant_copy_ops grows
so much, it pulls it out into a separate chunk of vmalloc()ed memory.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We should not assume that the PHY reset is always active low.

Retrieve this information from the device tree instead, so that the PHY reset
can work on both cases.
Reported-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A deadlock might occur if name table is withdrawn in socket release
routine, and while packets are still being received from bearer.

       CPU0                       CPU1
T0:   recv_msg()               release()
T1:   tipc_recv_msg()          tipc_withdraw()
T2:   [grab node lock]         [grab port lock]
T3:   tipc_link_wakeup_ports() tipc_nametbl_withdraw()
T4:   [grab port lock]*        named_cluster_distribute()
T5:   wakeupdispatch()         tipc_link_send()
T6:                            [grab node lock]*

The opposite order of holding port lock and node lock on above two
different paths may result in a deadlock. If socket lock instead of
port lock is used to protect port instance in tipc_withdraw(), the
reverse order of holding port lock and node lock will be eliminated,
as a result, the deadlock is killed as well.
Reported-by: Lars Everbrand <lars.everbrand@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 5c0484e2 ('powerpc: Endian safe trampoline') resulted in
losing proper alignment of the spinlock variables used when booting
secondary CPUs, causing some quite odd issues with failing to boot on
PA Semi-based systems.

This showed itself on ppc64_defconfig, but not on pasemi_defconfig,
so it had gone unnoticed when I initially tested the LE patch set.

Fix is to add explicit alignment instead of relying on good luck. :)

[ It appears that there is a different issue with PA Semi systems
  however this fix is definitely correct so applying anyway -- BenH
]

Fixes: 5c0484e2 ('powerpc: Endian safe trampoline')
Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=67811Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

p_end is an 8 byte value embedded in the text section. This means it
is only 4 byte aligned when it should be 8 byte aligned. Fix this
by adding an explicit alignment.

This fixes an issue where POWER7 little endian builds with
CONFIG_RELOCATABLE=y fail to boot.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Prevent ioda_eeh_hub_diag() from clobbering itself when called by supplying
a per-PHB buffer for P7IOC hub diagnostic data.  Take care to inform OPAL of
the correct size for the buffer.

[Small style change to the use of sizeof -- BenH]
Signed-off-by: Brian W Hart <hartb@linux.vnet.ibm.com>
Acked-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

PHB diagnostic buffer may be smaller than PAGE_SIZE, especially when
PAGE_SIZE > 4KB.
Signed-off-by: Brian W Hart <hartb@linux.vnet.ibm.com>
Acked-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The powerpc 64-bit __copy_tofrom_user() function uses shifts to handle
unaligned invocations.  However, these shifts were designed for
big-endian systems: On little-endian systems, they must shift in the
opposite direction.

This commit relies on the C preprocessor to insert the correct shifts
into the assembly code.

[ This is a rare but nasty LE issue. Most of the time we use the POWER7
optimised __copy_tofrom_user_power7 loop, but when it hits an exception
we fall back to the base __copy_tofrom_user loop. - Anton ]
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

The generic put_unaligned/get_unaligned macros were made endian-safe by
calling the appropriate endian dependent macros based on the endian type
of the powerpc processor.
Signed-off-by: Rajesh B Prathipati <rprathip@linux.vnet.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

In EXCEPTION_PROLOG_COMMON() we check to see if the stack pointer (r1)
is valid when coming from the kernel.  If it's not valid, we die but
with a nice oops message.

Currently we allocate a stack frame (subtract INT_FRAME_SIZE) before we
check to see if the stack pointer is negative.  Unfortunately, this
won't detect a bad stack where r1 is less than INT_FRAME_SIZE.

This patch fixes the check to compare the modified r1 with
-INT_FRAME_SIZE.  With this, bad kernel stack pointers (including NULL
pointers) are correctly detected again.

Kudos to Paulus for finding this.
Signed-off-by: Michael Neuling <mikey@neuling.org>
cc: stable@vger.kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>

Pull ARM SoC fixes from Olof Johansson:
 "Another smallish batch of fixes, it's been quiet due to the holidays.
  Nothing controversial here, a handful of things across the board"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: pxa: fix USB gadget driver compilation regression
  ARM: OMAP2+: Fix LCD panel backlight regression for LDP legacy booting
  ARM: OMAP2+: hwmod_data: fix missing OMAP_INTC_START in irq data
  ARM: DRA7: hwmod: Fix boot crash with DEBUG_LL
  ARM: shmobile: r8a7790: fix shdi resource sizes
  ARM: shmobile: bockw: fixup DMA mask
  ARM: shmobile: armadillo: Add PWM backlight power supply

Pull x86 fixes from Peter Anvin:
 "There is a small EFI fix and a big power regression fix in this batch.

  My queue also had a fix for downing a CPU when there are insufficient
  number of IRQ vectors available, but I'm holding that one for now due
  to recent bug reports"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/efi: Don't select EFI from certain special ACPI drivers
  x86 idle: Repair large-server 50-watt idle-power regression

Pull ACPI and power management fixes and new device IDs from Rafael Wysocki:

 - Fix for a cpufreq regression causing stale sysfs files to be left
   behind during system resume if cpufreq_add_dev() fails for one or
   more CPUs from Viresh Kumar.

 - Fix for a bug in cpufreq causing CONFIG_CPU_FREQ_DEFAULT_* to be
   ignored when the intel_pstate driver is used from Jason Baron.

 - System suspend fix for a memory leak in pm_vt_switch_unregister()
   that forgot to release objects after removing them from
   pm_vt_switch_list.  From Masami Ichikawa.

 - Intel Valley View device ID and energy unit encoding update for the
   (recently added) Intel RAPL (Running Average Power Limit) driver from
   Jacob Pan.

 - Intel Bay Trail SoC GPIO and ACPI device IDs for the Low Power
   Subsystem (LPSS) ACPI driver from Paul Drews.

* tag 'pm+acpi-3.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  powercap / RAPL: add support for ValleyView Soc
  PM / sleep: Fix memory leak in pm_vt_switch_unregister().
  cpufreq: Use CONFIG_CPU_FREQ_DEFAULT_* to set initial policy for setpolicy drivers
  cpufreq: remove sysfs files for CPUs which failed to come back after resume
  ACPI: Add BayTrail SoC GPIO and LPSS ACPI IDs

Included changes:

- reset netfilter-bridge state when removing the batman-adv
  header from an incoming packet. This prevents netfilter
  bridge from being fooled when the same packet enters a
  bridge twice (or more): the first time within the
  batman-adv header and the second time without.

- adjust the packet layout to prevent any architecture from
  adding padding bytes. All the structs sent over the wire
  now have size multiple of 4bytes (unless pack(2) is used).

- fix access to the inner vlan_eth header when reading the
  VID in the rx path.
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter/IPVS fixes for net

This patchset contains four nf_tables fixes, one IPVS fix due to
missing updates in the interaction with the new sedadj conntrack
extension that was added to support the netfilter synproxy code,
and a couple of one-liners to fix netnamespace netfilter issues.
More specifically, they are:

* Fix ipv6_find_hdr() call without offset being explicitly initialized
  in nft_exthdr, as required by that function, from Daniel Borkmann.

* Fix oops in nfnetlink_log when using netns and unloading the kernel
  module, from Gao feng.

* Fix BUG_ON in nf_ct_timestamp extension after netns is destroyed,
  from Helmut Schaa.

* Fix crash in IPVS due to missing sequence adjustment extension being
  allocated in the conntrack, from Jesper Dangaard Brouer.

* Add bugtrap to spot a warning in case you deference sequence adjustment
  conntrack area when not available, this should help to catch similar
  invalid dereferences in the Netfilter tree, also from Jesper.

* Fix incomplete dumping of sets in nf_tables when retrieving by family,
  from me.

* Fix oops when updating the table state (dormant <-> active) and having
  user (not base ) chains, from me.

* Fix wrong validation in set element data that results in returning
  -EINVAL when using the nf_tables dictionary feature with mappings,
  also from me.

We don't usually have this amount of fixes by this time (as we're already
in -rc5 of the development cycle), although half of them are related to
nf_tables which is a relatively new thing, and I also believe that holidays
have also delayed the flight of bugfixes to mainstream a bit.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'omap-for-v3.13/intc-ldp-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

From Tony Lindgren:
Fix a regression for wrong interrupt numbers for some devices after
the sparse IRQ conversion, fix DRA7 console output for earlyprintk,
and fix the LDP LCD backlight when DSS is built into the kernel and
not as a loadable module.

* tag 'omap-for-v3.13/intc-ldp-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP2+: Fix LCD panel backlight regression for LDP legacy booting
  ARM: OMAP2+: hwmod_data: fix missing OMAP_INTC_START in irq data
  ARM: DRA7: hwmod: Fix boot crash with DEBUG_LL
  + v3.13-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'renesas-fixes2-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes

From Simon Horman:
Second Round of Renesas ARM based SoC Fixes for v3.13

* r8a7790 (R-Car H2) based Lager board
  - Correct SHDI resource sizes
    This bug has been present since sdhi resources were added to the r8a7790 by
    8c9b1aa4 ("ARM: shmobile: r8a7790: add MMCIF and SDHI DT
    templates") in v3.11-rc2.

* r8a7778 (R-Car M1) based Bock-W board
  - Correct DMA mask
    This resolves a regression introduced by 4dcfa600
    ("ARM: DMA-API: better handing of DMA masks for coherent allocations")
    in v3.12-rc1.

* r8a7740 (R-Mobile A1) based Armadillo board
  - Add PWM backlight power supply
    This resolves a regression introduced by 22ceeee1
    ("pwm-backlight: Add power supply support") in v3.12.

* tag 'renesas-fixes2-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: r8a7790: fix shdi resource sizes
  ARM: shmobile: bockw: fixup DMA mask
  ARM: shmobile: armadillo: Add PWM backlight power supply
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Olof Johansson <olof@lixom.net>

After commit 88f718e3
"ARM: pxa: delete the custom GPIO header" a compilation
error was introduced in the PXA25x gadget driver.
An attempt to fix the problem was made in
commit b144e4ab
"usb: gadget: fix pxa25x compilation problems"
by explictly stating the driver needs the <mach/hardware.h>
header, which solved the compilation for a few boards,
such as the pxa255-idp and its defconfig.

However the Lubbock board has this special clause in
drivers/usb/gadget/pxa25x_udc.c:

This include file has an implicit dependency on
<mach/irqs.h> having been included before <mach/lubbock.h>
was included.

Before commit 88f718e3
"ARM: pxa: delete the custom GPIO header" this implicit
dependency for the pxa25x_udc compile on the Lubbock was
satisfied by <linux/gpio.h> implicitly including
<mach/gpio.h> which was in turn including <mach/irqs.h>,
apart from the earlier added <mach/hardware.h>.

Fix this by having the PXA25x <mach/lubbock.h> explicitly
include <mach/irqs.h>.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Greg Kroah-Hartmann <gregkh@linuxfoundation.org>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

This patch fixes dictionary mappings, eg.

 add rule ip filter input meta dnat set tcp dport map { 22 => 1.1.1.1, 23 => 2.2.2.2 }

The kernel was returning -EINVAL in nft_validate_data_load() since
the type of the set element data that is passed was the real userspace
datatype instead of NFT_DATA_VALUE.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

When batadv_get_vid() is invoked in interface_rx() the
batman-adv header has already been removed, therefore
the header_len argument has to be 0.

Introduced by c018ad3d
("batman-adv: add the VLAN ID attribute to the TT entry")
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>

If an interface enslaved into batman-adv is a bridge (or a
virtual interface built on top of a bridge) the nf_bridge
member of the skbs reaching the soft-interface is filled
with the state about "netfilter bridge" operations.

Then, if one of such skbs is locally delivered, the nf_bridge
member should be cleaned up to avoid that the old state
could mess up with other "netfilter bridge" operations when
entering a second bridge.
This is needed because batman-adv is an encapsulation
protocol.

However at the moment skb->nf_bridge is not released at all
leading to bogus "netfilter bridge" behaviours.

Fix this by cleaning the netfilter state of the skb before
it gets delivered to the upper layer in interface_rx().
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>

Make struct batadv_tvlv_tt_change a multiple 4 bytes long
to avoid padding on any architecture.
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>

Since this is a mac address and always 48 bit, and we can assume that
it is always aligned to 2-byte boundaries, add a pack(2) pragma.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>

struct batadv_icmp_header currently has a size of 17, which
will be padded to 20 on some architectures. Fix this by
unrolling the header into the parent structures.

Moreover keep the ICMP parsing functions as generic as they
are now by using a stub icmp_header struct during packet
parsing.
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>

The size of the batadv_header of 3 is problematic on some architectures
which automatically pad all structures to a 32 bit boundary. To not lose
performance by packing this struct, better embed it into the various
host structures.
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>

The compiler may decide to pad the structure, and then it does not
have the expected size of 46 byte. Fix this by moving it in the
pragma pack(2) part of the code.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>

This patch fixes a crash while trying to deactivate a table that
contains user chains. You can reproduce it via:

% nft add table table1
% nft add chain table1 chain1
% nft-table-upd ip table1 dormant

[  253.021026] BUG: unable to handle kernel NULL pointer dereference at 0000000000000030
[  253.021114] IP: [<ffffffff8134cebd>] nf_register_hook+0x35/0x6f
[  253.021167] PGD 30fa5067 PUD 30fa2067 PMD 0
[  253.021208] Oops: 0000 [#1] SMP
[...]
[  253.023305] Call Trace:
[  253.023331]  [<ffffffffa0885020>] nf_tables_newtable+0x11c/0x258 [nf_tables]
[  253.023385]  [<ffffffffa0878592>] nfnetlink_rcv_msg+0x1f4/0x226 [nfnetlink]
[  253.023438]  [<ffffffffa0878418>] ? nfnetlink_rcv_msg+0x7a/0x226 [nfnetlink]
[  253.023491]  [<ffffffffa087839e>] ? nfnetlink_bind+0x45/0x45 [nfnetlink]
[  253.023542]  [<ffffffff8134b47e>] netlink_rcv_skb+0x3c/0x88
[  253.023586]  [<ffffffffa0878973>] nfnetlink_rcv+0x3af/0x3e4 [nfnetlink]
[  253.023638]  [<ffffffff813fb0d4>] ? _raw_read_unlock+0x22/0x34
[  253.023683]  [<ffffffff8134af17>] netlink_unicast+0xe2/0x161
[  253.023727]  [<ffffffff8134b29a>] netlink_sendmsg+0x304/0x332
[  253.023773]  [<ffffffff8130d250>] __sock_sendmsg_nosec+0x25/0x27
[  253.023820]  [<ffffffff8130fb93>] sock_sendmsg+0x5a/0x7b
[  253.023861]  [<ffffffff8130d5d5>] ? copy_from_user+0x2a/0x2c
[  253.023905]  [<ffffffff8131066f>] ? move_addr_to_kernel+0x35/0x60
[  253.023952]  [<ffffffff813107b3>] SYSC_sendto+0x119/0x15c
[  253.023995]  [<ffffffff81401107>] ? sysret_check+0x1b/0x56
[  253.024039]  [<ffffffff8108dc30>] ? trace_hardirqs_on_caller+0x140/0x1db
[  253.024090]  [<ffffffff8120164e>] ? trace_hardirqs_on_thunk+0x3a/0x3f
[  253.024141]  [<ffffffff81310caf>] SyS_sendto+0x9/0xb
[  253.026219]  [<ffffffff814010e2>] system_call_fastpath+0x16/0x1b
Reported-by: Alex Wei <alex.kern.mentor@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

If not table name is specified, the dumping of the existing sets
may be incomplete with a sufficiently large number of sets and
tables. This patch fixes missing reset of the cursors after
finding the location of the last object that has been included
in the previous multi-part message.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

if a dst is not attached to anywhere, it should be released before
exit ipip6_tunnel_xmit, otherwise cause dst memory leakage.

Fixes: 61c1db7f ("ipv6: sit: add GSO/TSO support")
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netxen_process_lro() contains two bounds checks.  One for the ring number
against the number of rings, and one for the Rx buffer ID against the
array of receive buffers.

Both of these have off-by-one errors, using > instead of >=. The correct
versions are used in netxen_process_rcv(), they're just wrong in
netxen_process_lro().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

We've seen so many instances of people invoking skb_tx_timestamp()
after the device already has been given the packet, that it's worth
being a little bit more verbose and explicit in this comment.
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Eric Dumazet <edumazet@google.com>

skb_tx_timestamp(skb) should be called _before_ TX completion
has a chance to trigger, otherwise it is too late and we access
freed memory.

Fixes: e4f2379d ("ethernet/arc/arc_emac - Add new driver")
From: Eric Dumazet <edumazet@google.com>
Cc: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current driver assumes that an skb fragment can only be upto jumbo
size. Presumably this was a fast-path optimization. This assumption is
no longer true as fragments can be upto 32k.

v2: Remove unnecessary parantheses per Eric Dumazet.

Cc: stable@vger.kernel.org
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>