Add support for extended command id in notification system.
Extended command id header contains group id in addition to command id.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This makes various functions in the file rs.c void due to these
functions never returning a error code to signal to their callers
if and how they have failed to complete their intended work.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Move the TX PN assignment (for CCMP only) to the driver. This prepares
the driver for future DSO (driver segmentation offload) where it will
split an SKB into multiple MPDUs by itself.

For TDLS, split out the CCMP TX command handling so that it won't get
a PN assigned, the firmware assigns the PN in that case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Since the CSR_DRAM_INIT_TBL_WRITE_POINTER bit wasn't set
on ict reset, in some flows (like disable ict followed by
immediate reset ict) the driver and hardware went out
of sync (the driver cleared the ict_index, while the hw
kept it intact).

Fix it by setting the flag when resetting ict.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Some CSR registers have to be configured also
in case of suspend/resume with unified image
(which doesn't includes reconfiguration flow).

Reuse the existing d3_suspend/d3_resume trans ops,
while making sure some configurations are a bit
different, according to the wowlan type.

After this change, we no longer need the special
wowlan_d0i3 configurations done in iwl_pci_resume,
as they are already being done in the d3_resume op.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

CQM overwrites a few thresholds in the bf command. On the other hand,
when entering D0i3 the thresholds are set to higher values on purpose,
so ignore CQM in this case.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The slow filtering threshold should be higher in D0i3 case.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

TCP software implementation on the host requires extensive computing
power.  Offloading even some of the TCP/IP stack to the NIC might save
a significant overhead. In order to enable this feature on our hw,
we need to configure it first. Once done, we mark this capability,
to be advertised later to the OS via ieee80211_register_hw.
The driver Rx indications for TCP Checksum is integrated within the
standard Rx status. The driver responds to those indications as follows:
If the frame was tested by hw and checksum ok report CHECKSUM_UNNECESSARY.
Otherwise, report CHECKSUM_NONE.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The firmware debug infrastructure allows the user to
provide a firmware that will toggle a few registers to
configure the debugging capabilities.
On certain devices, certain operations are forbidden.
Executing a forbidden operation will cause the hardware to
die in a way that only driver unload / load will bring it
back to life.
Fortunately, there is a way to know in advance if those
operations will be accepted by the device. This is where
the new PRPH_BLOCKBIT operation plays its role. If the bit
X from PRPH register Y is set, then we should prevent any
further register configuration. When that happens, drop a
line in the kernel log since this is really an error state:
the user won't have his device configured as he expected.
Add operations that will be used in the future:
INDIRECT_ASSIGN, INDIRECT_SETBIT, and INDIRECT_CLEARBIT.

Other debugging configurations (such as destination
configuration for the monitor) will take place in any case.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

In iwl_mvm_tx_skb_non_sta(), in case of managed interface,
use the AP station for multicast frames instead of the auxiliary
station as otherwise the frames can be sent to an absent P2P GO as
the FW does not block transmissions for the auxiliary station
since it is not associated with the station MAC context.

Note that this is not possible for unicast frames, as a TDLS
discovery response is sent without a station entry, and in this
case the P2P GO NoA should not block transmission to the peer.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Allow the transport layer to return an error upon suspend.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This reverts commit 088070a2.

When working in d0i3_on_idle mode, we explicitly go out
of d0i3 on resume (so other potential commands could
be sent).

However, D0I3_DEFER_WAKEUP is currently cleared on
resume complete (which happens only later on), causing
d0i3 exit to timeout.

Since mac80211 was modified to accept incoming frames
once drv_resume was called, we can safely revert this
patch, and handle the pending work on iwl_mvm_resume().
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Existing UMAC commands already use the long header, but are sent
with group 0 and the long header inserted manually. Move them to
the group 1 to take advantage of the header building in the low-
level transport.

Existing firmware ignores the group_id field (it's reserved) and
the first firmware that really supports long command headers can
parse all commands in both group 0 (with short header) and group
1 (with long header.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

As the firmware is slowly running out of command IDs and grouping of
commands is desirable anyway, the firmware is extending the command
header from 4 bytes to 8 bytes to introduce a group (in place of the
former flags field, since that's always 0 on commands and thus can
be easily used to distinguish between the two.

In order to support this most easily in the driver widen the command
command ID used in the command sending functions and encode the new
values (group and version) in the ID. That way existing code doesn't
have to be changed (since the higher bits are 0 automatically) and
newer code can easily use the new ID generation function to create a
value to use in place of just the command ID.
Signed-off-by: Aviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

ToF is a time based method for measurement of the WiFi device
location within a WiFi environment. The driver functionality provided
by this patch is the interface for communication with FW and receiving
location related updates from the FW. The interface provided by this
patch is via debugfs.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

All the supported firmwares support this API.
This includes removing dwell per band, as band is no longer a factor
in calculating the dwell. Only basic dwell is used and FW will calculate
the actual dwell time.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The 'flags' field really has been reserved in the firmware API for a
very long time, probably since 4965. As a consequence, the field is
always 0 and checking for a IWL_CMD_FAILED_MSK flag makes no sense.

Rename the field to 'reserved', get rid of IWL_CMD_FAILED_MSK and
all the code for it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

In iwlmvm firmwares, the Byte count written in the scheduler
byte count table is in DWORDs and not in bytes.
We should check that this value fits in the 12 bits and
the value can be either in bits of in DWORD or bytes
depending on the firmware. Check the value after the
translation to DWORDs is done (if needed).
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

In a few places, we were disabling interrupts but didn't
make sure that the interrupt handler has finished running.
Add calls to synchronize_irq() to ensure we finish handling
the interrupts before we free resources or other things that
could lead to a crash if the interrupt were to be handled
later.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

When the firmware crashes, we can't expect the Tx queues to
progress. Cancel their timer.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Since the time-event is sent with the immediate flag set, there is
no need to sample the device time.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

With the previous patch series, no opmode continues using the
command or handler_status (i.e. the return value from the RX)
so it can be removed now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

In the mvm driver, neither the old command nor the return value
are used, so remove them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

After the previous patches, the command that's passed in nor the
return value are used any more, so can be removed.

While at it, make some functions static.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This makes the logging a little less useful, but as they're mostly
synchronous commands it won't matter much. It gets rid of the
dependency on the input command, which this is the only user of.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This driver currently has some very confusing ADD_STA response handling
that runs asynchronously in the background for all of the commands, but
is only really necessary for synchronous ones (the really asynchronous
ones can only be done for already existing stations), and for the sync
ones it actually waits for the RX handler to return a status code.

Rework this to keep the debug printing in the handler, but do the code
that's supposed to have an effect only for sync commands in the command
sending function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The current key offset assignment algorithm always uses the lowest
unused key offset, which will potentially lead to issues when the
firmware will change to take the key material for TX from the key
table rather than from the TX command.

In order to avoid those issues (and avoid forgetting about them)
change the key offset allocation algorithm now to avoid reusing key
offsets quickly.

The new algorithm always picks as the next offset the least recently
freed offset, i.e. the offset that has been unused for the longest
amount of time. This is implemented by having a generation counter
for each key offset that is incremented every time a key is deleted,
except for the one that's deleted, which is reset to zero. Thus the
highest counter is the key that's been unused longest.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

During NIC initialization shared HW is reset and this disables the
scheduler. Some HW platforms do not activate the scheduler after it.
Consequently all HCMD sent by the driver stay at the queues which cause
to queue stuck.
Set the scheduler to work on auto active mode so it would be activated upon
change over one of the queues' write pointer.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This allows to ensure that we don't have races between them.
A user reported that stop_device was called twice upon
rfkill interrupt after suspend. When the interrupts are
enabled, and right after when we directly check the rfkill
state.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The new locking in PCIe transport requires to start_hw
before start_fw. This uncovered a bug in dvm which failed
to do so.
Fix that.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This firmware is not supported anymore - stop loading this firmware.
Remove code handling older versions.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

There's no need to forward RX MPDUs to notification wait tests, nor
do we need to check them for firmware dump triggers, nor could they
be asynchronous. It's thus more efficient to handle them separately,
before going into the regular RX handlers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

In scenarios where we haven't converged yet to a specific modulation
and rate it could be better to report to userspace the last tx rate
based on the STA capabilities and RSSI. This is important as sometimes
userspace displays the last tx rate as the link speed.
This avoids being presented with low legacy rates when rs just begins
its search or after an idle period in which it resets itself.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Pull networking updates from David Miller:

 1) Add TX fast path in mac80211, from Johannes Berg.

 2) Add TSO/GRO support to ibmveth, from Thomas Falcon

 3) Move away from cached routes in ipv6, just like ipv4, from Martin
    KaFai Lau.

 4) Lots of new rhashtable tests, from Thomas Graf.

 5) Run ingress qdisc lockless, from Alexei Starovoitov.

 6) Allow servers to fetch TCP packet headers for SYN packets of new
    connections, for fingerprinting.  From Eric Dumazet.

 7) Add mode parameter to pktgen, for testing receive.  From Alexei
    Starovoitov.

 8) Cache access optimizations via simplifications of build_skb(), from
    Alexander Duyck.

 9) Move page frag allocator under mm/, also from Alexander.

10) Add xmit_more support to hv_netvsc, from KY Srinivasan.

11) Add a counter guard in case we try to perform endless reclassify
    loops in the packet scheduler.

12) Extern flow dissector to be programmable and use it in new "Flower"
    classifier.  From Jiri Pirko.

13) AF_PACKET fanout rollover fixes, performance improvements, and new
    statistics.  From Willem de Bruijn.

14) Add netdev driver for GENEVE tunnels, from John W Linville.

15) Add ingress netfilter hooks and filtering, from Pablo Neira Ayuso.

16) Fix handling of epoll edge triggers in TCP, from Eric Dumazet.

17) Add an ECN retry fallback for the initial TCP handshake, from Daniel
    Borkmann.

18) Add tail call support to BPF, from Alexei Starovoitov.

19) Add several pktgen helper scripts, from Jesper Dangaard Brouer.

20) Add zerocopy support to AF_UNIX, from Hannes Frederic Sowa.

21) Favor even port numbers for allocation to connect() requests, and
    odd port numbers for bind(0), in an effort to help avoid
    ip_local_port_range exhaustion.  From Eric Dumazet.

22) Add Cavium ThunderX driver, from Sunil Goutham.

23) Allow bpf programs to access skb_iif and dev->ifindex SKB metadata,
    from Alexei Starovoitov.

24) Add support for T6 chips in cxgb4vf driver, from Hariprasad Shenai.

25) Double TCP Small Queues default to 256K to accomodate situations
    like the XEN driver and wireless aggregation.  From Wei Liu.

26) Add more entropy inputs to flow dissector, from Tom Herbert.

27) Add CDG congestion control algorithm to TCP, from Kenneth Klette
    Jonassen.

28) Convert ipset over to RCU locking, from Jozsef Kadlecsik.

29) Track and act upon link status of ipv4 route nexthops, from Andy
    Gospodarek.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1670 commits)
  bridge: vlan: flush the dynamically learned entries on port vlan delete
  bridge: multicast: add a comment to br_port_state_selection about blocking state
  net: inet_diag: export IPV6_V6ONLY sockopt
  stmmac: troubleshoot unexpected bits in des0 & des1
  net: ipv4 sysctl option to ignore routes when nexthop link is down
  net: track link-status of ipv4 nexthops
  net: switchdev: ignore unsupported bridge flags
  net: Cavium: Fix MAC address setting in shutdown state
  drivers: net: xgene: fix for ACPI support without ACPI
  ip: report the original address of ICMP messages
  net/mlx5e: Prefetch skb data on RX
  net/mlx5e: Pop cq outside mlx5e_get_cqe
  net/mlx5e: Remove mlx5e_cq.sqrq back-pointer
  net/mlx5e: Remove extra spaces
  net/mlx5e: Avoid TX CQE generation if more xmit packets expected
  net/mlx5e: Avoid redundant dev_kfree_skb() upon NOP completion
  net/mlx5e: Remove re-assignment of wq type in mlx5e_enable_rq()
  net/mlx5e: Use skb_shinfo(skb)->gso_segs rather than counting them
  net/mlx5e: Static mapping of netdev priv resources to/from netdev TX queues
  net/mlx4_en: Use HW counters for rx/tx bytes/packets in PF device
  ...

Pull scheduler updates from Thomas Gleixner:
 "This series of scheduler updates depends on sched/core and timers/core
  branches, which are already in your tree:

   - Scheduler balancing overhaul to plug a hard to trigger race which
     causes an oops in the balancer (Peter Zijlstra)

   - Lockdep updates which are related to the balancing updates (Peter
     Zijlstra)"

* 'sched-hrtimers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched,lockdep: Employ lock pinning
  lockdep: Implement lock pinning
  lockdep: Simplify lock_release()
  sched: Streamline the task migration locking a little
  sched: Move code around
  sched,dl: Fix sched class hopping CBS hole
  sched, dl: Convert switched_{from, to}_dl() / prio_changed_dl() to balance callbacks
  sched,dl: Remove return value from pull_dl_task()
  sched, rt: Convert switched_{from, to}_rt() / prio_changed_rt() to balance callbacks
  sched,rt: Remove return value from pull_rt_task()
  sched: Allow balance callbacks for check_class_changed()
  sched: Use replace normalize_task() with __sched_setscheduler()
  sched: Replace post_schedule with a balance callback list

Pull locking updates from Thomas Gleixner:
 "These locking updates depend on the alreay merged sched/core branch:

   - Lockless top waiter wakeup for rtmutex (Davidlohr)

   - Reduce hash bucket lock contention for PI futexes (Sebastian)

   - Documentation update (Davidlohr)"

* 'sched-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  locking/rtmutex: Update stale plist comments
  futex: Lower the lock contention on the HB lock during wake up
  locking/rtmutex: Implement lockless top-waiter wakeup

Pull arm64 updates from Catalin Marinas:
 "Mostly refactoring/clean-up:

   - CPU ops and PSCI (Power State Coordination Interface) refactoring
     following the merging of the arm64 ACPI support, together with
     handling of Trusted (secure) OS instances

   - Using fixmap for permanent FDT mapping, removing the initial dtb
     placement requirements (within 512MB from the start of the kernel
     image).  This required moving the FDT self reservation out of the
     memreserve processing

   - Idmap (1:1 mapping used for MMU on/off) handling clean-up

   - Removing flush_cache_all() - not safe on ARM unless the MMU is off.
     Last stages of CPU power down/up are handled by firmware already

   - "Alternatives" (run-time code patching) refactoring and support for
     immediate branch patching, GICv3 CPU interface access

   - User faults handling clean-up

  And some fixes:

   - Fix for VDSO building with broken ELF toolchains

   - Fix another case of init_mm.pgd usage for user mappings (during
     ASID roll-over broadcasting)

   - Fix for FPSIMD reloading after CPU hotplug

   - Fix for missing syscall trace exit

   - Workaround for .inst asm bug

   - Compat fix for switching the user tls tpidr_el0 register"

* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (42 commits)
  arm64: use private ratelimit state along with show_unhandled_signals
  arm64: show unhandled SP/PC alignment faults
  arm64: vdso: work-around broken ELF toolchains in Makefile
  arm64: kernel: rename __cpu_suspend to keep it aligned with arm
  arm64: compat: print compat_sp instead of sp
  arm64: mm: Fix freeing of the wrong memmap entries with !SPARSEMEM_VMEMMAP
  arm64: entry: fix context tracking for el0_sp_pc
  arm64: defconfig: enable memtest
  arm64: mm: remove reference to tlb.S from comment block
  arm64: Do not attempt to use init_mm in reset_context()
  arm64: KVM: Switch vgic save/restore to alternative_insn
  arm64: alternative: Introduce feature for GICv3 CPU interface
  arm64: psci: fix !CONFIG_HOTPLUG_CPU build warning
  arm64: fix bug for reloading FPSIMD state after CPU hotplug.
  arm64: kernel thread don't need to save fpsimd context.
  arm64: fix missing syscall trace exit
  arm64: alternative: Work around .inst assembler bugs
  arm64: alternative: Merge alternative-asm.h into alternative.h
  arm64: alternative: Allow immediate branch as alternative instruction
  arm64: Rework alternate sequence for ARM erratum 845719
  ...

Pull first batch of KVM updates from Paolo Bonzini:
 "The bulk of the changes here is for x86.  And for once it's not for
  silicon that no one owns: these are really new features for everyone.

  Details:

   - ARM:
        several features are in progress but missed the 4.2 deadline.
        So here is just a smattering of bug fixes, plus enabling the
        VFIO integration.

   - s390:
        Some fixes/refactorings/optimizations, plus support for 2GB
        pages.

   - x86:
        * host and guest support for marking kvmclock as a stable
          scheduler clock.
        * support for write combining.
        * support for system management mode, needed for secure boot in
          guests.
        * a bunch of cleanups required for the above
        * support for virtualized performance counters on AMD
        * legacy PCI device assignment is deprecated and defaults to "n"
          in Kconfig; VFIO replaces it

        On top of this there are also bug fixes and eager FPU context
        loading for FPU-heavy guests.

   - Common code:
        Support for multiple address spaces; for now it is used only for
        x86 SMM but the s390 folks also have plans"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (124 commits)
  KVM: s390: clear floating interrupt bitmap and parameters
  KVM: x86/vPMU: Enable PMU handling for AMD PERFCTRn and EVNTSELn MSRs
  KVM: x86/vPMU: Implement AMD vPMU code for KVM
  KVM: x86/vPMU: Define kvm_pmu_ops to support vPMU function dispatch
  KVM: x86/vPMU: introduce kvm_pmu_msr_idx_to_pmc
  KVM: x86/vPMU: reorder PMU functions
  KVM: x86/vPMU: whitespace and stylistic adjustments in PMU code
  KVM: x86/vPMU: use the new macros to go between PMC, PMU and VCPU
  KVM: x86/vPMU: introduce pmu.h header
  KVM: x86/vPMU: rename a few PMU functions
  KVM: MTRR: do not map huge page for non-consistent range
  KVM: MTRR: simplify kvm_mtrr_get_guest_memory_type
  KVM: MTRR: introduce mtrr_for_each_mem_type
  KVM: MTRR: introduce fixed_mtrr_addr_* functions
  KVM: MTRR: sort variable MTRRs
  KVM: MTRR: introduce var_mtrr_range
  KVM: MTRR: introduce fixed_mtrr_segment table
  KVM: MTRR: improve kvm_mtrr_get_guest_memory_type
  KVM: MTRR: do not split 64 bits MSR content
  KVM: MTRR: clean up mtrr default type
  ...

Pull powerpc updates from Michael Ellerman:

 - disable the 32-bit vdso when building LE, so we can build with a
   64-bit only toolchain.

 - EEH fixes from Gavin & Richard.

 - enable the sys_kcmp syscall from Laurent.

 - sysfs control for fastsleep workaround from Shreyas.

 - expose OPAL events as an irq chip by Alistair.

 - MSI ops moved to pci_controller_ops by Daniel.

 - fix for kernel to userspace backtraces for perf from Anton.

 - merge pseries and pseries_le defconfigs from Cyril.

 - CXL in-kernel API from Mikey.

 - OPAL prd driver from Jeremy.

 - fix for DSCR handling & tests from Anshuman.

 - Powernv flash mtd driver from Cyril.

 - dynamic DMA Window support on powernv from Alexey.

 - LLVM clang fixes & workarounds from Anton.

 - reworked version of the patch to abort syscalls when transactional.

 - fix the swap encoding to support 4TB, from Aneesh.

 - various fixes as usual.

 - Freescale updates from Scott: Highlights include more 8xx
   optimizations, an e6500 hugetlb optimization, QMan device tree nodes,
   t1024/t1023 support, and various fixes and cleanup.

* tag 'powerpc-4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux: (180 commits)
  cxl: Fix typo in debug print
  cxl: Add CXL_KERNEL_API config option
  powerpc/powernv: Fix wrong IOMMU table in pnv_ioda_setup_bus_dma()
  powerpc/mm: Change the swap encoding in pte.
  powerpc/mm: PTE_RPN_MAX is not used, remove the same
  powerpc/tm: Abort syscalls in active transactions
  powerpc/iommu/ioda2: Enable compile with IOV=on and IOMMU_API=off
  powerpc/include: Add opal-prd to installed uapi headers
  powerpc/powernv: fix construction of opal PRD messages
  powerpc/powernv: Increase opal-irqchip initcall priority
  powerpc: Make doorbell check preemption safe
  powerpc/powernv: pnv_init_idle_states() should only run on powernv
  macintosh/nvram: Remove as unused
  powerpc: Don't use gcc specific options on clang
  powerpc: Don't use -mno-strict-align on clang
  powerpc: Only use -mtraceback=no, -mno-string and -msoft-float if toolchain supports it
  powerpc: Only use -mabi=altivec if toolchain supports it
  powerpc: Fix duplicate const clang warning in user access code
  vfio: powerpc/spapr: Support Dynamic DMA windows
  vfio: powerpc/spapr: Register memory and define IOMMU v2
  ...