- 21 Aug, 2016 40 commits
-
-
Alex Deucher authored
commit d814b24f upstream. ATPX dGPU power control requires a 200ms delay between power off and on. This should fix dGPU failures on resume from power off. Reviewed-by:
Hawking Zhang <Hawking.Zhang@amd.com> Acked-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by:
Willy Tarreau <w@1wt.eu>
-
Alex Deucher authored
commit 05082b8b upstream. When executing in a PCI passthrough based virtuzliation environment, the hypervisor will usually attempt to send a PCIe bus reset signal to the ASIC when the VM reboots. In this scenario, the card is not correctly initialized, but we still consider it to be posted. Therefore, in a passthrough based environemnt we should always post the card to guarantee it is in a good state for driver initialization. Ported from amdgpu commit: amdgpu: fix asic initialization for virtualized environments Cc: Andres Rodriguez <andres.rodriguez@amd.com> Cc: Alex Williamson <alex.williamson@redhat.com> Signed-off-by:
-
Lyude authored
commit 255f0e7c upstream. During boot, MST hotplugs are generally expected (even if no physical hotplugging occurs) and result in DRM's connector topology changing. This means that using num_connector from the current mode configuration can lead to the number of connectors changing under us. This can lead to some nasty scenarios in fbcon: - We allocate an array to the size of dev->mode_config.num_connectors. - MST hotplug occurs, dev->mode_config.num_connectors gets incremented. - We try to loop through each element in the array using the new value of dev->mode_config.num_connectors, and end up going out of bounds since dev->mode_config.num_connectors is now larger then the array we allocated. fb_helper->connector_count however, will always remain consistent while we do a modeset in fb_helper. Note: This is just polish for 4.7, Dave Airlie's drm_connector refcounting fixed these bugs for real. But it's good enough duct-tape for stable kernel backporting, since backporting the refcounting changes is way too invasive. Signed-off-by:
Lyude <cpaul@redhat.com> [danvet: Clarify why we need this. Also remove the now unused "dev" local variable to appease gcc.] Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Link: http://patchwork.freedesktop.org/patch/msgid/1463065021-18280-3-git-send-email-cpaul@redhat.comSigned-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Itai Handler authored
commit 7ccca1d5 upstream. Fix possible out of bounds read, by adding missing comma. The code may read pass the end of the dsi_errors array when the most significant bit (bit #31) in the intr_stat register is set. This bug has been detected using CppCheck (static analysis tool). Cc: stable@vger.kernel.org Signed-off-by:
Itai Handler <itai_handler@hotmail.com> Signed-off-by:
Patrik Jakobsson <patrik.r.jakobsson@gmail.com> Signed-off-by:
-
Tomáš Trnka authored
commit c0cb8bf3 upstream. The length of the GSS MIC token need not be a multiple of four bytes. It is then padded by XDR to a multiple of 4 B, but unwrap_integ_data() would previously only trim mic.len + 4 B. The remaining up to three bytes would then trigger a check in nfs4svc_decode_compoundargs(), leading to a "garbage args" error and mount failure: nfs4svc_decode_compoundargs: compound not properly padded! nfsd: failed to decode arguments! This would prevent older clients using the pre-RFC 4121 MIC format (37-byte MIC including a 9-byte OID) from mounting exports from v3.9+ servers using krb5i. The trimming was introduced by commit 4c190e2f ("sunrpc: trim off trailing checksum before returning decrypted or integrity authenticated buffer"). Fixes: 4c190e2f "unrpc: trim off trailing checksum..." Signed-off-by:
Tomáš Trnka <ttrnka@mail.muni.cz> Cc: stable@vger.kernel.org Acked-by:
Jeff Layton <jlayton@poochiereds.net> Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Signed-off-by:
-
Cyril Bur authored
commit 8e96a87c upstream. Userspace can quite legitimately perform an exec() syscall with a suspended transaction. exec() does not return to the old process, rather it load a new one and starts that, the expectation therefore is that the new process starts not in a transaction. Currently exec() is not treated any differently to any other syscall which creates problems. Firstly it could allow a new process to start with a suspended transaction for a binary that no longer exists. This means that the checkpointed state won't be valid and if the suspended transaction were ever to be resumed and subsequently aborted (a possibility which is exceedingly likely as exec()ing will likely doom the transaction) the new process will jump to invalid state. Secondly the incorrect attempt to keep the transactional state while still zeroing state for the new process creates at least two TM Bad Things. The first triggers on the rfid to return to userspace as start_thread() has given the new process a 'clean' MSR but the suspend will still be set in the hardware MSR. The second TM Bad Thing triggers in __switch_to() as the processor is still transactionally suspended but __switch_to() wants to zero the TM sprs for the new process. This is an example of the outcome of calling exec() with a suspended transaction. Note the first 700 is likely the first TM bad thing decsribed earlier only the kernel can't report it as we've loaded userspace registers. c000000000009980 is the rfid in fast_exception_return() Bad kernel stack pointer 3fffcfa1a370 at c000000000009980 Oops: Bad kernel stack pointer, sig: 6 [#1] CPU: 0 PID: 2006 Comm: tm-execed Not tainted NIP: c000000000009980 LR: 0000000000000000 CTR: 0000000000000000 REGS: c00000003ffefd40 TRAP: 0700 Not tainted MSR: 8000000300201031 <SF,ME,IR,DR,LE,TM[SE]> CR: 00000000 XER: 00000000 CFAR: c0000000000098b4 SOFTE: 0 PACATMSCRATCH: b00000010000d033 GPR00: 0000000000000000 00003fffcfa1a370 0000000000000000 0000000000000000 GPR04: 0000000000000000 0000000000000000 0000000000000000 0000000000000000 GPR08: 0000000000000000 0000000000000000 0000000000000000 0000000000000000 GPR12: 00003fff966611c0 0000000000000000 0000000000000000 0000000000000000 NIP [c000000000009980] fast_exception_return+0xb0/0xb8 LR [0000000000000000] (null) Call Trace: Instruction dump: f84d0278 e9a100d8 7c7b03a6 e84101a0 7c4ff120 e8410170 7c5a03a6 e8010070 e8410080 e8610088 e8810090 e8210078 <4c000024> 48000000 e8610178 88ed023b Kernel BUG at c000000000043e80 [verbose debug info unavailable] Unexpected TM Bad Thing exception at c000000000043e80 (msr 0x201033) Oops: Unrecoverable exception, sig: 6 [#2] CPU: 0 PID: 2006 Comm: tm-execed Tainted: G D task: c0000000fbea6d80 ti: c00000003ffec000 task.ti: c0000000fb7ec000 NIP: c000000000043e80 LR: c000000000015a24 CTR: 0000000000000000 REGS: c00000003ffef7e0 TRAP: 0700 Tainted: G D MSR: 8000000300201033 <SF,ME,IR,DR,RI,LE,TM[SE]> CR: 28002828 XER: 00000000 CFAR: c000000000015a20 SOFTE: 0 PACATMSCRATCH: b00000010000d033 GPR00: 0000000000000000 c00000003ffefa60 c000000000db5500 c0000000fbead000 GPR04: 8000000300001033 2222222222222222 2222222222222222 00000000ff160000 GPR08: 0000000000000000 800000010000d033 c0000000fb7e3ea0 c00000000fe00004 GPR12: 0000000000002200 c00000000fe00000 0000000000000000 0000000000000000 GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000 GPR20: 0000000000000000 0000000000000000 c0000000fbea7410 00000000ff160000 GPR24: c0000000ffe1f600 c0000000fbea8700 c0000000fbea8700 c0000000fbead000 GPR28: c000000000e20198 c0000000fbea6d80 c0000000fbeab680 c0000000fbea6d80 NIP [c000000000043e80] tm_restore_sprs+0xc/0x1c LR [c000000000015a24] __switch_to+0x1f4/0x420 Call Trace: Instruction dump: 7c800164 4e800020 7c0022a6 f80304a8 7c0222a6 f80304b0 7c0122a6 f80304b8 4e800020 e80304a8 7c0023a6 e80304b0 <7c0223a6> e80304b8 7c0123a6 4e800020 This fixes CVE-2016-5828. Fixes: bc2a9408 ("powerpc: Hook in new transactional memory code") Cc: stable@vger.kernel.org # v3.9+ Signed-off-by:
Cyril Bur <cyrilbur@gmail.com> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Gavin Shan authored
commit 8a934efe upstream. In commit 8445a87f "powerpc/iommu: Remove the dependency on EEH struct in DDW mechanism", the PE address was replaced with the PCI config address in order to remove dependency on EEH. According to PAPR spec, firmware (pHyp or QEMU) should accept "xxBBSSxx" format PCI config address, not "xxxxBBSS" provided by the patch. Note that "BB" is PCI bus number and "SS" is the combination of slot and function number. This fixes the PCI address passed to DDW RTAS calls. Fixes: 8445a87f ("powerpc/iommu: Remove the dependency on EEH struct in DDW mechanism") Cc: stable@vger.kernel.org # v3.4+ Reported-by:
Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com> Signed-off-by:
Gavin Shan <gwshan@linux.vnet.ibm.com> Tested-by:
-
Guilherme G. Piccoli authored
commit 8445a87f upstream. Commit 39baadbf ("powerpc/eeh: Remove eeh information from pci_dn") changed the pci_dn struct by removing its EEH-related members. As part of this clean-up, DDW mechanism was modified to read the device configuration address from eeh_dev struct. As a consequence, now if we disable EEH mechanism on kernel command-line for example, the DDW mechanism will fail, generating a kernel oops by dereferencing a NULL pointer (which turns to be the eeh_dev pointer). This patch just changes the configuration address calculation on DDW functions to a manual calculation based on pci_dn members instead of using eeh_dev-based address. No functional changes were made. This was tested on pSeries, both in PHyp and qemu guest. Fixes: 39baadbf ("powerpc/eeh: Remove eeh information from pci_dn") Cc: stable@vger.kernel.org # v3.4+ Reviewed-by:
-
Russell Currey authored
commit 871e178e upstream. In the "ibm,configure-pe" and "ibm,configure-bridge" RTAS calls, the spec states that values of 9900-9905 can be returned, indicating that software should delay for 10^x (where x is the last digit, i.e. 990x) milliseconds and attempt the call again. Currently, the kernel doesn't know about this, and respecting it fixes some PCI failures when the hypervisor is busy. The delay is capped at 0.2 seconds. Cc: <stable@vger.kernel.org> # 3.10+ Signed-off-by:
Russell Currey <ruscur@russell.cc> Acked-by:
-
Thomas Huth authored
commit 8dd75ccb upstream. We are already using the privileged versions of MMCR0, MMCR1 and MMCRA in the kernel, so for MMCR2, we should better use the privileged versions, too, to be consistent. Fixes: 240686c1 ("powerpc: Initialise PMU related regs on Power8") Suggested-by:
Paul Mackerras <paulus@ozlabs.org> Signed-off-by:
Thomas Huth <thuth@redhat.com> Acked-by:
-
Thomas Huth authored
commit d23fac2b upstream. The SIAR and SDAR registers are available twice, one time as SPRs 780 / 781 (unprivileged, but read-only), and one time as the SPRs 796 / 797 (privileged, but read and write). The Linux kernel code currently uses the unprivileged SPRs - while this is OK for reading, writing to that register of course does not work. Since the KVM code tries to write to this register, too (see the mtspr in book3s_hv_rmhandlers.S), the contents of this register sometimes get lost for the guests, e.g. during migration of a VM. To fix this issue, simply switch to the privileged SPR numbers instead. Signed-off-by:
-
Hari Bathini authored
commit 8ed8ab40 upstream. Some of the interrupt vectors on 64-bit POWER server processors are only 32 bytes long (8 instructions), which is not enough for the full first-level interrupt handler. For these we need to branch to an out-of-line (OOL) handler. But when we are running a relocatable kernel, interrupt vectors till __end_interrupts marker are copied down to real address 0x100. So, branching to labels (ie. OOL handlers) outside this section must be handled differently (see LOAD_HANDLER()), considering relocatable kernel, which would need at least 4 instructions. However, branching from interrupt vector means that we corrupt the CFAR (come-from address register) on POWER7 and later processors as mentioned in commit 1707dd16. So, EXCEPTION_PROLOG_0 (6 instructions) that contains the part up to the point where the CFAR is saved in the PACA should be part of the short interrupt vectors before we branch out to OOL handlers. But as mentioned already, there are interrupt vectors on 64-bit POWER server processors that are only 32 bytes long (like vectors 0x4f00, 0x4f20, etc.), which cannot accomodate the above two cases at the same time owing to space constraint. Currently, in these interrupt vectors, we simply branch out to OOL handlers, without using LOAD_HANDLER(), which leaves us vulnerable when running a relocatable kernel (eg. kdump case). While this has been the case for sometime now and kdump is used widely, we were fortunate not to see any problems so far, for three reasons: 1. In almost all cases, production kernel (relocatable) is used for kdump as well, which would mean that crashed kernel's OOL handler would be at the same place where we end up branching to, from short interrupt vector of kdump kernel. 2. Also, OOL handler was unlikely the reason for crash in almost all the kdump scenarios, which meant we had a sane OOL handler from crashed kernel that we branched to. 3. On most 64-bit POWER server processors, page size is large enough that marking interrupt vector code as executable (see commit 429d2e83) leads to marking OOL handler code from crashed kernel, that sits right below interrupt vector code from kdump kernel, as executable as well. Let us fix this by moving the __end_interrupts marker down past OOL handlers to make sure that we also copy OOL handlers to real address 0x100 when running a relocatable kernel. This fix has been tested successfully in kdump scenario, on an LPAR with 4K page size by using different default/production kernel and kdump kernel. Also tested by manually corrupting the OOL handlers in the first kernel and then kdump'ing, and then causing the OOL handlers to fire - mpe. Fixes: c1fb6816 ("powerpc: Add relocation on exception vector handlers") Signed-off-by:
Hari Bathini <hbathini@linux.vnet.ibm.com> Signed-off-by:
Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com> Signed-off-by:
-
wang yanqing authored
commit 873ffe15 upstream. In commit a269913c ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter() to use work queue"), the tests for enter/exit power-save mode were inverted. With this change applied, the wifi connection becomes much more stable. Fixes: a269913c ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter() to use work queue") Signed-off-by:
Wang YanQing <udknight@gmail.com> Acked-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Prarit Bhargava authored
commit ad67b437 upstream. b84106b4 ("PCI: Disable IO/MEM decoding for devices with non-compliant BARs") disabled BAR sizing for BARs 0-5 of devices that don't comply with the PCI spec. But it didn't do anything for expansion ROM BARs, so we still try to size them, resulting in warnings like this on Broadwell-EP: pci 0000:ff:12.0: BAR 6: failed to assign [mem size 0x00000001 pref] Move the non-compliant BAR check from __pci_read_base() up to pci_read_bases() so it applies to the expansion ROM BAR as well as to BARs 0-5. Note that direct callers of __pci_read_base(), like sriov_init(), will now bypass this check. We haven't had reports of devices with broken SR-IOV BARs yet. [bhelgaas: changelog] Fixes: b84106b4 ("PCI: Disable IO/MEM decoding for devices with non-compliant BARs") Signed-off-by:
Prarit Bhargava <prarit@redhat.com> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> CC: Thomas Gleixner <tglx@linutronix.de> CC: Ingo Molnar <mingo@redhat.com> CC: "H. Peter Anvin" <hpa@zytor.com> CC: Andi Kleen <ak@linux.intel.com> Signed-off-by:
-
Raghava Aditya Renukunta authored
commit fc4bf75e upstream. Typically under error conditions, it is possible for aac_command_thread() to miss the wakeup from kthread_stop() and go back to sleep, causing it to hang aac_shutdown. In the observed scenario, the adapter is not functioning correctly and so aac_fib_send() never completes (or time-outs depending on how it was called). Shortly after aac_command_thread() starts it performs aac_fib_send(SendHostTime) which hangs. When aac_probe_one /aac_get_adapter_info send time outs, kthread_stop is called which breaks the command thread out of it's hang. The code will still go back to sleep in schedule_timeout() without checking kthread_should_stop() so it causes aac_probe_one to hang until the schedule_timeout() which is 30 minutes. Fixed by: Adding another kthread_should_stop() before schedule_timeout() Cc: stable@vger.kernel.org Signed-off-by:
Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com> Reviewed-by:
Johannes Thumshirn <jthumshirn@suse.de> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Raghava Aditya Renukunta authored
commit 07beca2b upstream. aac_fib_send has a special function case for initial commands during driver initialization using wait < 0(pseudo sync mode). In this case, the command does not sleep but rather spins checking for timeout.This loop is calls cpu_relax() in an attempt to allow other processes/threads to use the CPU, but this function does not relinquish the CPU and so the command will hog the processor. This was observed in a KDUMP "crashkernel" and that prevented the "command thread" (which is responsible for completing the command from being timed out) from starting because it could not get the CPU. Fixed by replacing "cpu_relax()" call with "schedule()" Cc: stable@vger.kernel.org Signed-off-by:
-
Joseph Salisbury authored
commit 7b9bc799 upstream. BugLink: http://bugs.launchpad.net/bugs/972604 Commit 09c9bae2 ("ath5k: add led pin configuration for compaq c700 laptop") added a pin configuration for the Compaq c700 laptop. However, the polarity of the led pin is reversed. It should be red for wifi off and blue for wifi on, but it is the opposite. This bug was reported in the following bug report: http://pad.lv/972604 Fixes: 09c9bae2 ("ath5k: add led pin configuration for compaq c700 laptop") Signed-off-by:
Joseph Salisbury <joseph.salisbury@canonical.com> Cc: stable@vger.kernel.org Signed-off-by:
Kalle Valo <kvalo@qca.qualcomm.com> Signed-off-by:
-
Cameron Gutman authored
commit caca925f upstream. This prevents a malicious USB device from causing an oops. Signed-off-by:
Cameron Gutman <aicommander@gmail.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Ping Cheng authored
commit 12afb344 upstream. Somehow the patch that added two-finger touch support forgot to update W8001_MAX_LENGTH from 11 to 13. Signed-off-by:
Ping Cheng <pingc@wacom.com> Reviewed-by:
Peter Hutterer <peter.hutterer@who-t.net> Cc: stable@vger.kernel.org Signed-off-by:
-
Ricky Liang authored
commit affa80bd upstream. When running a 32-bit userspace on a 64-bit kernel, the UI_SET_PHYS ioctl needs to be treated with special care, as it has the pointer size encoded in the command. Signed-off-by:
Ricky Liang <jcliang@chromium.org> Cc: stable@vger.kernel.org Signed-off-by:
-
James Hogan authored
commit 797179bc upstream. Copy __kvm_mips_vcpu_run() into unmapped memory, so that we can never get a TLB refill exception in it when KVM is built as a module. This was observed to happen with the host MIPS kernel running under QEMU, due to a not entirely transparent optimisation in the QEMU TLB handling where TLB entries replaced with TLBWR are copied to a separate part of the TLB array. Code in those pages continue to be executable, but those mappings persist only until the next ASID switch, even if they are marked global. An ASID switch happens in __kvm_mips_vcpu_run() at exception level after switching to the guest exception base. Subsequent TLB mapped kernel instructions just prior to switching to the guest trigger a TLB refill exception, which enters the guest exception handlers without updating EPC. This appears as a guest triggered TLB refill on a host kernel mapped (host KSeg2) address, which is not handled correctly as user (guest) mode accesses to kernel (host) segments always generate address error exceptions. Signed-off-by:
James Hogan <james.hogan@imgtec.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: Radim KrÄmáŠ<rkrcmar@redhat.com> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: kvm@vger.kernel.org Cc: linux-mips@linux-mips.org Cc: <stable@vger.kernel.org> # 3.10.x- Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> [james.hogan@imgtec.com: backported for stable 3.14] Signed-off-by:
-
Ralf Baechle authored
commit d7de4134 upstream. TASK_SIZE was defined as 0x7fff8000UL which for 64k pages is not a multiple of the page size. Somewhere further down the math fails such that executing an ELF binary fails. Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Tested-by:
Joshua Henderson <joshua.henderson@microchip.com> Cc: James Hogan <james.hogan@imgtec.com> Signed-off-by:
-
Matthias Schiffer authored
commit f5b556c9 upstream. This makes the ath79 bootconsole behave the same way as the generic 8250 bootconsole. Also waiting for TEMT (transmit buffer is empty) instead of just THRE (transmit buffer is not full) ensures that all characters have been transmitted before the real serial driver starts reconfiguring the serial controller (which would sometimes result in garbage being transmitted.) This change does not cause a visible performance loss. In addition, this seems to fix a hang observed in certain configurations on many AR7xxx/AR9xxx SoCs during autoconfig of the real serial driver. A more complete follow-up patch will disable 8250 autoconfig for ath79 altogether (the serial controller is detected as a 16550A, which is not fully compatible with the ath79 serial, and the autoconfig may lead to undefined behavior on ath79.) Cc: <stable@vger.kernel.org> Signed-off-by:
Matthias Schiffer <mschiffer@universe-factory.net> Signed-off-by:
-
James Hogan authored
commit 5daebc47 upstream. Commit 85efde6f ("make exported headers use strict posix types") changed the asm-generic siginfo.h to use the __kernel_* types, and commit 3a471cbc ("remove __KERNEL_STRICT_NAMES") make the internal types accessible only to the kernel, but the MIPS implementation hasn't been updated to match. Switch to proper types now so that the exported asm/siginfo.h won't produce quite so many compiler errors when included alone by a user program. Signed-off-by:
-
Paul Burton authored
commit ab4a92e6 upstream. When emulating a jalr instruction with rd == $0, the code in isBranchInstr was incorrectly writing to GPR $0 which should actually always remain zeroed. This would lead to any further instructions emulated which use $0 operating on a bogus value until the task is next context switched, at which point the value of $0 in the task context would be restored to the correct zero by a store in SAVE_SOME. Fix this by not writing to rd if it is $0. Fixes: 102cedc3 ("MIPS: microMIPS: Floating point support.") Signed-off-by:
Paul Burton <paul.burton@imgtec.com> Cc: Maciej W. Rozycki <macro@imgtec.com> Cc: James Hogan <james.hogan@imgtec.com> Cc: linux-mips@linux-mips.org Cc: linux-kernel@vger.kernel.org Patchwork: https://patchwork.linux-mips.org/patch/13160/Signed-off-by:
-
James Hogan authored
commit 9b731bcf upstream. Propagate errors from kvm_mips_handle_kseg0_tlb_fault() and kvm_mips_handle_mapped_seg_tlb_fault(), usually triggering an internal error since they normally indicate the guest accessed bad physical memory or the commpage in an unexpected way. Fixes: 858dd5d4 ("KVM/MIPS32: MMU/TLB operations for the Guest.") Fixes: e685c689 ("KVM/MIPS32: Privileged instruction/target branch emulation.") Signed-off-by:
Radim KrÄmáŠ<rkrcmar@redhat.com> [james.hogan@imgtec.com: Backport to v3.10.y - v3.15.y] Signed-off-by:
-
James Hogan authored
commit 0741f52d upstream. Two consecutive gfns are loaded into host TLB, so ensure the range check isn't off by one if guest_pmap_npages is odd. Fixes: 858dd5d4 ("KVM/MIPS32: MMU/TLB operations for the Guest.") Signed-off-by:
-
James Hogan authored
commit 8985d503 upstream. kvm_mips_handle_mapped_seg_tlb_fault() calculates the guest frame number based on the guest TLB EntryLo values, however it is not range checked to ensure it lies within the guest_pmap. If the physical memory the guest refers to is out of range then dump the guest TLB and emit an internal error. Fixes: 858dd5d4 ("KVM/MIPS32: MMU/TLB operations for the Guest.") Signed-off-by:
-
James Hogan authored
commit c604cffa upstream. kvm_mips_handle_mapped_seg_tlb_fault() appears to map the guest page at virtual address 0 to PFN 0 if the guest has created its own mapping there. The intention is unclear, but it may have been an attempt to protect the zero page from being mapped to anything but the comm page in code paths you wouldn't expect from genuine commpage accesses (guest kernel mode cache instructions on that address, hitting trapping instructions when executing from that address with a coincidental TLB eviction during the KVM handling, and guest user mode accesses to that address). Fix this to check for mappings exactly at KVM_GUEST_COMMPAGE_ADDR (it may not be at address 0 since commit 42aa12e7 ("MIPS: KVM: Move commpage so 0x0 is unmapped")), and set the corresponding EntryLo to be interpreted as 0 (invalid). Fixes: 858dd5d4 ("KVM/MIPS32: MMU/TLB operations for the Guest.") Signed-off-by:
-
Soheil Hassas Yeganeh authored
commit f626300a upstream. tcp_select_initial_window() intends to advertise a window scaling for the maximum possible window size. To do so, it considers the maximum of net.ipv4.tcp_rmem[2] and net.core.rmem_max as the only possible upper-bounds. However, users with CAP_NET_ADMIN can use SO_RCVBUFFORCE to set the socket's receive buffer size to values larger than net.ipv4.tcp_rmem[2] and net.core.rmem_max. Thus, SO_RCVBUFFORCE is effectively ignored by tcp_select_initial_window(). To fix this, consider the maximum of net.ipv4.tcp_rmem[2], net.core.rmem_max and socket's initial buffer space. Fixes: b0573dea ("[NET]: Introduce SO_{SND,RCV}BUFFORCE socket options") Signed-off-by:
Soheil Hassas Yeganeh <soheil@google.com> Suggested-by:
Neal Cardwell <ncardwell@google.com> Acked-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Yuchung Cheng authored
commit ce3cf4ec upstream. The v6 tcp stats scan do not provide TLP and ER timer information correctly like the v4 version . This patch fixes that. Fixes: 6ba8a3b1 ("tcp: Tail loss probe (TLP)") Fixes: eed530b6 ("tcp: early retransmit") Signed-off-by:
Yuchung Cheng <ycheng@google.com> Signed-off-by:
-
Charles (Chas) Williams authored
commit 75ff39cc upstream. From: Eric Dumazet <edumazet@google.com> Yue Cao claims that current host rate limiting of challenge ACKS (RFC 5961) could leak enough information to allow a patient attacker to hijack TCP sessions. He will soon provide details in an academic paper. This patch increases the default limit from 100 to 1000, and adds some randomization so that the attacker can no longer hijack sessions without spending a considerable amount of probes. Based on initial analysis and patch from Linus. Note that we also have per socket rate limiting, so it is tempting to remove the host limit in the future. v2: randomize the count of challenge acks per second, not the period. Fixes: 282f23c6 ("tcp: implement RFC 5961 3.2") Reported-by:
Yue Cao <ycao009@ucr.edu> Signed-off-by:
Eric Dumazet <edumazet@google.com> Suggested-by:
Linus Torvalds <torvalds@linux-foundation.org> Cc: Yuchung Cheng <ycheng@google.com> Cc: Neal Cardwell <ncardwell@google.com> Acked-by:
Chas Williams <ciwillia@brocade.com> Signed-off-by:
-
Hugh Dickins authored
commit 7f556567 upstream. The well-spotted fallocate undo fix is good in most cases, but not when fallocate failed on the very first page. index 0 then passes lend -1 to shmem_undo_range(), and that has two bad effects: (a) that it will undo every fallocation throughout the file, unrestricted by the current range; but more importantly (b) it can cause the undo to hang, because lend -1 is treated as truncation, which makes it keep on retrying until every page has gone, but those already fully instantiated will never go away. Big thank you to xfstests generic/269 which demonstrates this. Fixes: b9b4bb26 ("tmpfs: don't undo fallocate past its last page") Signed-off-by:
Hugh Dickins <hughd@google.com> Signed-off-by:
-
Anthony Romano authored
commit b9b4bb26 upstream. When fallocate is interrupted it will undo a range that extends one byte past its range of allocated pages. This can corrupt an in-use page by zeroing out its first byte. Instead, undo using the inclusive byte range. Fixes: 1635f6a7 ("tmpfs: undo fallocation on failure") Link: http://lkml.kernel.org/r/1462713387-16724-1-git-send-email-anthony.romano@coreos.comSigned-off-by:
Anthony Romano <anthony.romano@coreos.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: Hugh Dickins <hughd@google.com> Cc: Brandon Philips <brandon@ifup.co> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Ilya Dryomov authored
commit 930c5328 upstream. Currently, osd_weight and osd_state fields are updated in the encoding order. This is wrong, because an incremental map may look like e.g. new_up_client: { osd=6, addr=... } # set osd_state and addr new_state: { osd=6, xorstate=EXISTS } # clear osd_state Suppose osd6's current osd_state is EXISTS (i.e. osd6 is down). After applying new_up_client, osd_state is changed to EXISTS | UP. Carrying on with the new_state update, we flip EXISTS and leave osd6 in a weird "!EXISTS but UP" state. A non-existent OSD is considered down by the mapping code 2087 for (i = 0; i < pg->pg_temp.len; i++) { 2088 if (ceph_osd_is_down(osdmap, pg->pg_temp.osds[i])) { 2089 if (ceph_can_shift_osds(pi)) 2090 continue; 2091 2092 temp->osds[temp->size++] = CRUSH_ITEM_NONE; and so requests get directed to the second OSD in the set instead of the first, resulting in OSD-side errors like: [WRN] : client.4239 192.168.122.21:0/2444980242 misdirected client.4239.1:2827 pg 2.5df899f2 to osd.4 not [1,4,6] in e680/680 and hung rbds on the client: [ 493.566367] rbd: rbd0: write 400000 at 11cc00000 (0) [ 493.566805] rbd: rbd0: result -6 xferred 400000 [ 493.567011] blk_update_request: I/O error, dev rbd0, sector 9330688 The fix is to decouple application from the decoding and: - apply new_weight first - apply new_state before new_up_client - twiddle osd_state flags if marking in - clear out some of the state if osd is destroyed Fixes: http://tracker.ceph.com/issues/14901Signed-off-by:
Ilya Dryomov <idryomov@gmail.com> Reviewed-by:
Josh Durgin <jdurgin@redhat.com> [idryomov@gmail.com: backport to 3.10-3.14: strip primary-affinity] Signed-off-by:
-
Scott Bauer authored
commit 93a2001b upstream. This patch validates the num_values parameter from userland during the HIDIOCGUSAGES and HIDIOCSUSAGES commands. Previously, if the report id was set to HID_REPORT_ID_UNKNOWN, we would fail to validate the num_values parameter leading to a heap overflow. CVE-2016-5829 Cc: stable@vger.kernel.org Signed-off-by:
Scott Bauer <sbauer@plzdonthack.me> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Tejun Heo authored
commit 8d91f8b1 upstream. @console_may_schedule tracks whether console_sem was acquired through lock or trylock. If the former, we're inside a sleepable context and console_conditional_schedule() performs cond_resched(). This allows console drivers which use console_lock for synchronization to yield while performing time-consuming operations such as scrolling. However, the actual console outputting is performed while holding irq-safe logbuf_lock, so console_unlock() clears @console_may_schedule before starting outputting lines. Also, only a few drivers call console_conditional_schedule() to begin with. This means that when a lot of lines need to be output by console_unlock(), for example on a console registration, the task doing console_unlock() may not yield for a long time on a non-preemptible kernel. If this happens with a slow console devices, for example a serial console, the outputting task may occupy the cpu for a very long time. Long enough to trigger softlockup and/or RCU stall warnings, which in turn pile more messages, sometimes enough to trigger the next cycle of warnings incapacitating the system. Fix it by making console_unlock() insert cond_resched() between lines if @console_may_schedule. Signed-off-by:
Tejun Heo <tj@kernel.org> Reported-by:
Calvin Owens <calvinowens@fb.com> Acked-by:
Jan Kara <jack@suse.com> Cc: Dave Jones <davej@codemonkey.org.uk> Cc: Kyle McMartin <kyle@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Hugh Dickins authored
commit 42cb14b1 upstream. clear_page_dirty_for_io() has accumulated writeback and memcg subtleties since v2.6.16 first introduced page migration; and the set_page_dirty() which completed its migration of PageDirty, later had to be moderated to __set_page_dirty_nobuffers(); then PageSwapBacked had to skip that too. No actual problems seen with this procedure recently, but if you look into what the clear_page_dirty_for_io(page)+set_page_dirty(newpage) is actually achieving, it turns out to be nothing more than moving the PageDirty flag, and its NR_FILE_DIRTY stat from one zone to another. It would be good to avoid a pile of irrelevant decrementations and incrementations, and improper event counting, and unnecessary descent of the radix_tree under tree_lock (to set the PAGECACHE_TAG_DIRTY which radix_tree_replace_slot() left in place anyway). Do the NR_FILE_DIRTY movement, like the other stats movements, while interrupts still disabled in migrate_page_move_mapping(); and don't even bother if the zone is the same. Do the PageDirty movement there under tree_lock too, where old page is frozen and newpage not yet visible: bearing in mind that as soon as newpage becomes visible in radix_tree, an un-page-locked set_page_dirty() might interfere (or perhaps that's just not possible: anything doing so should already hold an additional reference to the old page, preventing its migration; but play safe). But we do still need to transfer PageDirty in migrate_page_copy(), for those who don't go the mapping route through migrate_page_move_mapping(). CVE-2016-3070 Signed-off-by:
-
Dan Carpenter authored
commit 38327424 upstream. If __key_link_begin() failed then "edit" would be uninitialized. I've added a check to fix that. This allows a random user to crash the kernel, though it's quite difficult to achieve. There are three ways it can be done as the user would have to cause an error to occur in __key_link(): (1) Cause the kernel to run out of memory. In practice, this is difficult to achieve without ENOMEM cropping up elsewhere and aborting the attempt. (2) Revoke the destination keyring between the keyring ID being looked up and it being tested for revocation. In practice, this is difficult to time correctly because the KEYCTL_REJECT function can only be used from the request-key upcall process. Further, users can only make use of what's in /sbin/request-key.conf, though this does including a rejection debugging test - which means that the destination keyring has to be the caller's session keyring in practice. (3) Have just enough key quota available to create a key, a new session keyring for the upcall and a link in the session keyring, but not then sufficient quota to create a link in the nominated destination keyring so that it fails with EDQUOT. The bug can be triggered using option (3) above using something like the following: echo 80 >/proc/sys/kernel/keys/root_maxbytes keyctl request2 user debug:fred negate @t The above sets the quota to something much lower (80) to make the bug easier to trigger, but this is dependent on the system. Note also that the name of the keyring created contains a random number that may be between 1 and 10 characters in size, so may throw the test off by changing the amount of quota used. Assuming the failure occurs, something like the following will be seen: kfree_debugcheck: out of range ptr 6b6b6b6b6b6b6b68h ------------[ cut here ]------------ kernel BUG at ../mm/slab.c:2821! ... RIP: 0010:[<ffffffff811600f9>] kfree_debugcheck+0x20/0x25 RSP: 0018:ffff8804014a7de8 EFLAGS: 00010092 RAX: 0000000000000034 RBX: 6b6b6b6b6b6b6b68 RCX: 0000000000000000 RDX: 0000000000040001 RSI: 00000000000000f6 RDI: 0000000000000300 RBP: ffff8804014a7df0 R08: 0000000000000001 R09: 0000000000000000 R10: ffff8804014a7e68 R11: 0000000000000054 R12: 0000000000000202 R13: ffffffff81318a66 R14: 0000000000000000 R15: 0000000000000001 ... Call Trace: kfree+0xde/0x1bc assoc_array_cancel_edit+0x1f/0x36 __key_link_end+0x55/0x63 key_reject_and_link+0x124/0x155 keyctl_reject_key+0xb6/0xe0 keyctl_negate_key+0x10/0x12 SyS_keyctl+0x9f/0xe7 do_syscall_64+0x63/0x13a entry_SYSCALL64_slow_path+0x25/0x25 CVE-2016-4470 Fixes: f70e2e06 ('KEYS: Do preallocation for __key_link()') Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
David Howells <dhowells@redhat.com> cc: stable@vger.kernel.org Signed-off-by:
-
Bjørn Mork authored
commit 4d06dd53 upstream. usbnet_link_change will call schedule_work and should be avoided if bind is failing. Otherwise we will end up with scheduled work referring to a netdev which has gone away. Instead of making the call conditional, we can just defer it to usbnet_probe, using the driver_info flag made for this purpose. CVE-2016-3951 Fixes: 8a34b0ae ("usbnet: cdc_ncm: apply usbnet_link_change") Reported-by:
Andrey Konovalov <andreyknvl@gmail.com> Suggested-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
