- 19 Jan, 2017 8 commits
-
-
Gabriel Krisman Bertazi authored
This avoids using the deprecated drm_put_dev() and unload() hook interfaces in the qxl driver. Signed-off-by:
Gabriel Krisman Bertazi <krisman@collabora.co.uk> Cc: Dave Airlie <airlied@redhat.com> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Gustavo Padovan <gustavo.padovan@collabora.com> Signed-off-by:
Gustavo Padovan <gustavo.padovan@collabora.com> Link: http://patchwork.freedesktop.org/patch/msgid/20170119134806.8926-2-krisman@collabora.co.uk
-
Gabriel Krisman Bertazi authored
This avoids using the deprecated drm_get_pci_dev() and load() hook interfaces in the qxl driver. The only tricky part is to ensure TTM debugfs initialization happens after the debugfs root node is created, which is done by moving that code into the debufs_init() hook. Tested on qemu with igt and running a WM on top of X. Changes since v1: - Drop verification for primary minor in qxl_debugsfs_init. Changes since V2: - Put new header together with other debugfs headers. Signed-off-by:
-
John Stultz authored
I've found that by just turning the chip on and off via the POWER_DOWN register, I end up getting i2c_transfer errors on HiKey. Investigating further, it turns out that some of the register state in hardware is getting lost, as the device registers are reset when the chip is powered down. Thus this patch simply re-writes the i2c address to the ADV7511_REG_EDID_I2C_ADDR register to ensure its properly set before we try to read the EDID data. Cc: David Airlie <airlied@linux.ie> Cc: Archit Taneja <architt@codeaurora.org> Cc: Wolfram Sang <wsa+renesas@sang-engineering.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: dri-devel@lists.freedesktop.org Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Tested-by:
John Stultz <john.stultz@linaro.org> Signed-off-by:
Archit Taneja <architt@codeaurora.org> Link: http://patchwork.freedesktop.org/patch/msgid/1484614372-15342-7-git-send-email-john.stultz@linaro.org
-
John Stultz authored
Thus this patch changes the EDID probing logic so that we re-use the __adv7511_power_on/off() calls instead of duplciating logic. This does change behavior slightly as it adds the HPD signal pulse to the EDID probe path, but Archit has had a patch to add HPD signal pulse to the EDID probe path before, so this should address the cases where that helped. Another difference is that regcache_mark_dirty() is also called in the power off path once EDID is probed. Cc: David Airlie <airlied@linux.ie> Cc: Archit Taneja <architt@codeaurora.org> Cc: Wolfram Sang <wsa+renesas@sang-engineering.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: dri-devel@lists.freedesktop.org Reviewed-by:
-
John Stultz authored
In chasing down issues with EDID probing, I found some duplicated but incomplete logic used to power the chip on and off. This patch refactors the adv7511_power_on/off functions, so they can be used for internal needs. Cc: David Airlie <airlied@linux.ie> Cc: Archit Taneja <architt@codeaurora.org> Cc: Wolfram Sang <wsa+renesas@sang-engineering.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: dri-devel@lists.freedesktop.org Signed-off-by:
-
Archit Taneja authored
On some adv7511 implementations, we can get some spurious disconnect signals which can cause monitor probing to fail. This patch enables HPD (hot plug detect) interrupt support which allows the monitor to be properly re-initialized when the spurious disconnect signal goes away. This also enables proper hotplug support. Cc: David Airlie <airlied@linux.ie> Cc: Archit Taneja <architt@codeaurora.org> Cc: Wolfram Sang <wsa+renesas@sang-engineering.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: dri-devel@lists.freedesktop.org Acked-by:
-
John Stultz authored
In chasing down a previous issue with EDID probing from calling drm_helper_hpd_irq_event() from irq context, Laurent noticed that the DRM documentation suggests that drm_kms_helper_hotplug_event() should be used instead. Thus this patch replaces drm_helper_hpd_irq_event() with drm_kms_helper_hotplug_event(), which requires we update the connector.status entry and only call _hotplug_event() when the status changes. Cc: David Airlie <airlied@linux.ie> Cc: Archit Taneja <architt@codeaurora.org> Cc: Wolfram Sang <wsa+renesas@sang-engineering.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: dri-devel@lists.freedesktop.org Reviewed-by:
-
John Stultz authored
I was recently seeing issues with EDID probing, where the logic to wait for the EDID read bit to be set by the IRQ wasn't happening and the code would time out and fail. Digging deeper, I found this was due to the fact that IRQs were disabled as we were running in IRQ context from the HPD signal. Thus this patch changes the logic to handle the HPD signal via a work_struct so we can be out of irq context. With this patch, the EDID probing on hotplug does not time out. Cc: David Airlie <airlied@linux.ie> Cc: Archit Taneja <architt@codeaurora.org> Cc: Wolfram Sang <wsa+renesas@sang-engineering.com> Cc: Lars-Peter Clausen <lars@metafoo.de> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: dri-devel@lists.freedesktop.org Reviewed-by:
-
- 18 Jan, 2017 26 commits
-
-
Shawn Guo authored
Use drm_crtc_from_index() to find drm_crtc for given index, so that we do not need to maintain a pointer array in struct vc4_dev. Signed-off-by:
Shawn Guo <shawn.guo@linaro.org> Cc: Eric Anholt <eric@anholt.net> Signed-off-by:
Sean Paul <seanpaul@chromium.org> Link: http://patchwork.freedesktop.org/patch/msgid/1483961145-18453-7-git-send-email-shawnguo@kernel.org
-
Shawn Guo authored
Function tegra_crtc_from_pipe() does the exactly same thing as what crtc helper drm_crtc_from_index() provides. Use the helper to save some code. Signed-off-by:
-
Shawn Guo authored
Use drm_crtc_from_index() to find drm_crtc for given index. Signed-off-by:
-
Shawn Guo authored
Use drm_crtc_from_index() to find drm_crtc for given index, so that we do not need to maintain a pointer array in struct mtk_drm_private. Signed-off-by:
-
Shawn Guo authored
Use drm_crtc_from_index() to find drm_crtc for given index, so that we do not need to maintain a pointer array in struct kirin_drm_private. Reviewed-by: Xinliang Liu<z.liuxinliang@hisilicon.com> Signed-off-by:
-
Shawn Guo authored
Use drm_crtc_from_index() to find drm_crtc for given index, so that we do not need to maintain a pointer array in struct exynos_drm_private. Signed-off-by:
-
Laurent Pinchart authored
Make it clear that the core bridge/dw_hdmi.txt document isn't a device tree binding by itself but is meant to be referenced by platform device tree bindings, and update the Rockchip and Freescale DWC HDMI TX bindings to reference it. Signed-off-by:
Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Acked-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Laurent Pinchart authored
According to the PHY IP core vendor, the SVSRET signal must be asserted before resetting the PHY. Tests on RK3288 and R-Car Gen3 showed no regression, the change should thus be safe. Signed-off-by:
Jose Abreu <joabreu@synopsys.com> Signed-off-by:
-
Laurent Pinchart authored
The PHY reset signal is controlled by bit PHYRSTZ in the MC_PHYRSTZ register. The signal is active low on Gen1 PHYs and active high on Gen2 PHYs. The driver toggles the signal high then low, which is correct for all currently supported platforms, but the register values macros are incorrectly named. Replace them with a single macro named after the bit, and add a comment to the source code to explain the behaviour. The driver's behaviour isn't changed by this rename, the code will still need to be fixed to support Gen1 PHYs. Signed-off-by:
-
Laurent Pinchart authored
Replace the hardcoded register address numerical values with macros to clarify the code. This change has been tested by comparing the assembly code before and after the change. Signed-off-by:
-
Laurent Pinchart authored
Detect the PHY type and use it to handle the PHY type-specific SVSRET signal. Signed-off-by:
-
Laurent Pinchart authored
Use the device version queried at runtime instead of the device type provided through platform data to handle the overflow workaround. This will make support of other SoCs integrating the same HDMI TX controller version easier. Among the supported platforms only i.MX6DL and i.MX6Q have been identified as needing the workaround. Disabling it on Rockchip RK3288 (which integrates a v2.00a controller) didn't produce any error or artifact. Signed-off-by:
-
Laurent Pinchart authored
Bit 0 in CONFIG1_ID tells whether the IP core uses an AHB slave interface for control. The correct way to identify AHB audio DMA support is through bit 1 in CONFIG3_ID. Signed-off-by:
-
Laurent Pinchart authored
The DWC HDMI TX can be recognized by the two product identification registers. If the registers don't read as expect the IP will be very different than what the driver has been designed for, or will be misconfigured in a way that makes it non-operational (invalid memory address, incorrect clocks, ...). We should reject this situation with an error. While this isn't critical for proper operation with supported IPs at the moment, the driver will soon gain automatic device-specific handling based on runtime device identification. This change makes it easier to implement that without having to default to a random guess in case the device can't be identified. While at it print a readable version number in the device identification message instead of raw register values. Signed-off-by:
-
Laurent Pinchart authored
The bit is documented in a Rockchip BSP as #define m_SVSRET_SIG (1 << 5) /* depend on PHY_MHL_COMB0=1 */ This is confirmed by a Renesas platform, which uses a 2.0 DWC HDMI TX as the RK3288. Rename the bit accordingly. Signed-off-by:
-
Kieran Bingham authored
The current code hard codes the call of hdmi_phy_configure() to be 8bpp and provides extraneous error checking to verify that this hardcoded value is correct. Simplify the implementation by removing the argument. Signed-off-by:
Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> Signed-off-by:
-
Laurent Pinchart authored
As an option for drivers not based on the component framework, register the bridge with the DRM core with the DRM bridge API. Existing drivers based on dw_hdmi_bind() and dw_hdmi_unbind() are not affected as those functions are preserved with their current behaviour. Signed-off-by:
-
Laurent Pinchart authored
The DRM device is not guaranteed by the bridge API to be available before the attach callback. The driver performs properly at the moment as it doesn't use the drm_bridge_add() registration method. As this will be changed later, move connector creation to attach time to ensure compatibility with the API. Signed-off-by:
-
Laurent Pinchart authored
The next commit will reference structures and functions in a way that currently requires forward declarations. Reorder the functions to avoid that. No functional change to the code is performed. Signed-off-by:
-
Laurent Pinchart authored
There's no need to duplicate identical code in multiple drivers (two at the moment, one more to come soon). Move it to the dw-hdmi core where it can be shared. If resource allocation ever becomes device-specific later we'll always have the option of splitting it out again. While it at pass the platform device to the bind function to avoid having to cast struct device to struct platform_device. Signed-off-by:
-
Laurent Pinchart authored
Hotplug events should only be forwarded to the DRM core by the interrupt handler when the bridge has been attached, otherwise the DRM device pointer will be NULL, resulting in a crash. Signed-off-by:
-
Laurent Pinchart authored
The field isn't needed, remove it. Signed-off-by:
-
Laurent Pinchart authored
The drm_bridge instance is always needed, there's no point in allocating it separately. Signed-off-by:
-
Kieran Bingham authored
The 'prep' parameter passed to hdmi_phy_configure() is useless. It is hardcoded as 0, and if set, simply prevents the configure function from executing. Remove it. Signed-off-by:
-
Laurent Pinchart authored
The master argument isn't used. The data argument, a void pointer, is used by the bind function only where it's cast to a drm_device pointer, which can easily be obtained from the encoder argument instead. Remove them. Signed-off-by:
-
Laurent Pinchart authored
The latter is just an int wrapper around the former void function that unconditionally returns 0. As the return value is never checked, merge the two functions into one. Signed-off-by:
-
- 17 Jan, 2017 3 commits
-
-
Gabriel Krisman Bertazi authored
Registering the connector explicitly right after creation is not necessary for modesetting drivers, because drm_dev_register already takes care of this on the core side, by calling drm_modeset_register_all. In addition, performing the initialization too early will get in the way of the load() hook removal, because the connector interface cannot be published prior to registering the minors. Signed-off-by:
-
Archit Taneja authored
Maintain a table of regulator names expected by ADV7511 and ADV7533. Use regulator_bulk_* api to configure these. Initialize and enable the regulators during probe itself. Controlling these dynamically is left for later. Reviewed-by:
-
Archit Taneja authored
Add the regulator supply properties needed by ADV7511 and ADV7533. Acked-by:
-
- 12 Jan, 2017 3 commits
-
-
Daniel Vetter authored
This is the deprecated function for when you embedded the framebuffer somewhere else (which breaks refcounting). But Tegra is using drm_framebuffer_remove and a free-standing FB, so this is redundant. One caveat here is that the failure path in the init code still manually cleaned up the fb. I presume that was an oversight and changed it over to drm_framebuffer_remove too. Cc: Thierry Reding <thierry.reding@gmail.com> Reviewed-by:
Thierry Reding <treding@nvidia.com> Signed-off-by:
Daniel Vetter <daniel.vetter@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1482835765-12044-5-git-send-email-daniel.vetter@ffwll.ch Link: http://patchwork.freedesktop.org/patch/msgid/1482835765-12044-2-git-send-email-daniel.vetter@ffwll.ch
-
Daniel Vetter authored
This is the deprecated function for when you embedded the framebuffer somewhere else (which breaks refcounting). But cma helpers are using drm_framebuffer_remove and a free-standing fb, so this is rendundant. Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Reviewed-by:
-
Daniel Vetter authored
This is the deprecated function for when you embedded the framebuffer somewhere else (which breaks refcounting). But omapdrm is using drm_framebuffer_remove and a free-standing fb, so this is rendundant. Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Reviewed-by:
-
