- 11 Aug, 2012 13 commits
-
-
Laurent Pinchart authored
Rearrange the CFA interpolation coefficients table based on the Bayer pattern. Support for non-Bayer CFA patterns is dropped as they were not correctly supported, and have never been tested. Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Acked-by:
Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com>
-
Laurent Pinchart authored
Enabling gamma bypass disables gamma correction and vice versa. Merge the two parameters. Signed-off-by:
-
Laurent Pinchart authored
Reorder the configuration and enable functions to match the parameters order. Signed-off-by:
-
Laurent Pinchart authored
Instead of using void pointers and offset arithmetics to compute a pointer to configuration parameters in a generic way, pass the complete parameters structure to configuration functions and let them access the parameters they need. Also modify the enable functions to use a bool enable parameter instead of a u8. Signed-off-by:
-
Laurent Pinchart authored
The feature isn't fully implemented and doesn't work, remove it. Signed-off-by:
-
Michael Jones authored
Signed-off-by:
Michael Jones <michael.jones@matrix-vision.de> Signed-off-by:
-
Peter Meerwald authored
Signed-off-by:
Peter Meerwald <pmeerw@pmeerw.net> Signed-off-by:
-
Laurent Pinchart authored
This needs to be performed before enabling interrupts as the sensor might be free-running and the ISP default setting (HS edge) would put an unnecessary burden on the CPU. Signed-off-by:
-
Laurent Pinchart authored
Use the existing omap3isp_subclk_enable() and omap3isp_subclk_disable() functions instead. Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
-
Hans Verkuil authored
Signed-off-by:
-
Hans Verkuil authored
Two of the four possible YUV formats got the wrong colorspace. Signed-off-by:
-
Devin Heitmueller authored
The register read function is referencing the dev->ctrlmsg structure outside of the dev->mutex lock, which can cause corruption of the value if multiple callers are invoking au0828_readreg() simultaneously. Use a stack variable to hold the result, and copy the buffer returned by usb_control_msg() to that variable. In reality, the whole recv_control_msg() function can probably be collapsed into au0288_readreg() since it is the only caller. Also get rid of cmd_msg_dump() since the only case in which the function is ever called only is ever passed a single byte for the response (and it is already logged). Signed-off-by:
Devin Heitmueller <dheitmueller@kernellabs.com> Signed-off-by:
-
- 10 Aug, 2012 3 commits
-
-
Ezequiel García authored
Signed-off-by:
Ezequiel Garcia <elezegarcia@gmail.com> Signed-off-by:
-
Igor M. Liplianin authored
This patch seems for rectifying a typo. But actually the difference between mantis_vp2040.c and mantis_vp2033.c code is a card name only. Signed-off-by:
Igor M. Liplianin <liplianin@me.by> Signed-off-by:
-
Devin Heitmueller authored
The original xc5000c driver support was based on a beta version of the firmware, and there were no redistribution rights. Change over to using the release version, for which freely redistributable firmware can be found here: http://kernellabs.com/firmware/xc5000/README.xc5000c http://kernellabs.com/firmware/xc5000/dvb-fe-xc5000c-4.1.30.7.fw Thanks to Ramon Cazares from Cresta Technology for making the firmware available as well as working out the licensing issues. [mchehab@redhat.com: Fix a merge conflict with the patch that added support for MODULE_FIRMWARE() macro] Signed-off-by:
-
- 09 Aug, 2012 24 commits
-
-
Devin Heitmueller authored
Make the firmware speedup work for the 5000c as well as the original xc5000. This cuts firmware load time in half. Thanks to John Casey at Hauppauge for loaning me a board for testing. Signed-off-by:
-
Devin Heitmueller authored
This patch addresses a couple of cases where I forgot to pop open the gate when in analog mode (a correlary to fix the change made in patch 1c58d5b4a5fca42dce5428bd79b9405878017735). Signed-off-by:
-
Devin Heitmueller authored
The driver prints out a dotted version number but it's in hex. As a result, the version doesn't visibly match the filename for the firmware, and it caused a bunch of confusion while discussing different versions with the chip manufacturer. Change the firmware printout to be in decimal. Signed-off-by:
-
Devin Heitmueller authored
The hack I put in a couple of years ago to avoid clock stretching issues when talking to the xc5000 worked fine for writes, but intermittently fails for register reads, because the xc5000 may stretch the clock for longer between bytes (I was seeing cases of 21 us on the analyzer). The problem manifested itself as the xc5000 firmware version and PLL lock register intermittently showing garbage values. Slow down the i2c bus from 30 KHz to 20 KHz to accommodate. Signed-off-by:
-
Devin Heitmueller authored
The xc5000c and newer versions of the xc5000a firmware need minor revisions to their initialization process. Add support for validating the firmware was properly loaded, as well as checking the init status after initialization. Based on advice from CrestaTech support as well as xc5000 datasheet v2.3. Signed-off-by:
-
Devin Heitmueller authored
It's possible for the xc5000 to enter an unknown state such that all subsequent tuning requests fail. The only way to recover is to reset the tuner and reload the firmware. This problem was detected after several days straight of issuing tuning requests every five seconds. Reset the firmware in the event that the PLL is in an unlocked state. This solution was provided by the engineer at CrestaTech (the company that acquired Xceive). Signed-off-by:
-
Devin Heitmueller authored
Adjust the retry timeout and number of retries to speed up xc5000 firmware download. With this change it goes from 4.2 seconds to 2.9. The net time waited is pretty much the same, but we just poll more often. Tested at 250 KHz as well as 30 KHz. Signed-off-by:
-
Devin Heitmueller authored
There are no cases where a control message is ever sent to the au0828 with an actual buffer defined. Remove the reference to dev->ctrlmsg, which currently requires us to hold a mutex since it is shared with the read function. Signed-off-by:
-
Devin Heitmueller authored
Put a hack in place to speed up the firmware load in the case that the xc5000 has just been reset. The chip can safely do 400 KHz in this mode, while in normal operation it can only do 100 KHz. This reduces the firmware load time from 6.9 seconds to 4.2. Signed-off-by:
-
Devin Heitmueller authored
We weren't checking whether the resource was in use before calling res_free(), so applications which called STREAMOFF on a v4l2 device that wasn't already streaming would cause a BUG() to be hit (MythTV). Reported-by:
Larry Finger <larry.finger@lwfinger.net> Reported-by:
Jay Harbeston <jharbestonus@gmail.com> Signed-off-by:
-
Devin Heitmueller authored
The original implementation of the analog support would use an i2c_gate_ctrl function when using the digital side of the au8522, but on the analog side we would always just force the gate open and leave it open all the time. This can have adverse effects on the xc5000 given the tuner is receiving all the spurious i2c traffic (a problem which can be exaggerated due to bugs in the au0828 i2c hardware implementation). Rework the existing hack to only open/close the gate when actually talking to the tuner. This logic might need to be reworked a bit if anybody ever tries to add support for a board that has the au0828/au8522 but doesn't have digital support implemented (because the i2c_gate_ctrl callback is being set in the DVB attach). However given how few different models are in circulation, this can be deferred until such a situation arises (if ever). Signed-off-by:
-
Devin Heitmueller authored
The current code invokes the auto calibration of the tuner whenever the init routine is called (whenever the DVB frontend opens the device). However we should really only be invoking the calibration if we actually did reset the device and reload the firmware. Rework the routine to only do calibration if reset and firmware load was performed. Also because the called function is now a no-op if the firmware is already loaded, the caller no longer needs to invoke is_firmware_loaded(). Signed-off-by:
-
Devin Heitmueller authored
The au8522 driver was broken into three modules (dig, decoder, common), and as a result the debug modprobe option doesn't work for any of the common functions. Copy the module macros over to the common module so that the debug option works again. Signed-off-by:
-
Devin Heitmueller authored
If the user performs a tuning attempt without explicitly calling the s_std ioctl(), a value of zero is sent from tuner-core to xc5000. This causes the xc5000 driver to leave the standard unchanged. The problem was masked by the fact that the xc5000 driver defaulted to NTSC, but if you happened to perform an ATSC/ClearQAM tuning attempt and then do an analog tune, the net effect is an analog tune with the standard still set to DTV6. Keep track of whether the standard has ever been sent to tuner-core. We don't make an s_std subdev call explicitly during probe because that will cause a firmware load (which is very time consuming on the 950q). With the logic in this patch, the s_std call will occur automatically on the s_freq call if it hasn't already been set. Signed-off-by:
-
Devin Heitmueller authored
In some cases users would see the xc5000_attach() call failing for the digital side of the tuner on initialization. This is because of udev running v4l-id while the digital side of the board is still coming up. This is the exact same race condition which was present in em28xx (not surprising since I copied all the locking logic from that driver when I added analog support). Reproduce Mauro's fix from the em28xx driver in au0828. Reported-by:
Rick Harding <rharding@mitechie.com> Signed-off-by:
-
Devin Heitmueller authored
The logic as written would *never* actually return an error condition, since the loop would run until the counter hit zero but the check was for a value less than zero. Signed-off-by:
-
Devin Heitmueller authored
When debugging is enabled, also show the analog SNR and the total gain status values. Signed-off-by:
-
Devin Heitmueller authored
The quality register only has relevant data in bits 2-0, so discard the other bits (which results in a value being printed that is consistent with the expected 0-7 range). Signed-off-by:
-
Devin Heitmueller authored
The g_reg and s_reg calls worked properly if acting on subdev registers (such as the au8522), but didn't work against the au0828 itself. Copy the logic over from em28xx. Signed-off-by:
-
Devin Heitmueller authored
There is an apparent bug in the au8522 TS clocking which can result in it delivering a TS payload to the au0828 that is shifted by some number of bits. For example, the device will announce a packet containing "FA 38 FF F8" which if you shift left one bit is "1F 47 1F FF F0..." This presents itself as no TS stream being delivered from the kernel to userland, since the kernel demux will drop every packet. In the event that this condition occurs, restart the DVB stream. Also, this patch includes a couple of lines of cleanup to not change the FIFO configuration while the FIFO is running (which can screw up the state machine), and dequeue the buffers before turning off the FIFO. This puts the logic in sync with the Windows driver. Signed-off-by:
-
Devin Heitmueller authored
The table of valid SNR values for QAM 256 is off by one, and as a result if the SNR is oscillating between 40.0 and 39.9 dB, tools like azap show it going back and forth between 40.0 and 0 (misleading some people, including myself, to think signal lock is being lost or there is a problem with register reads). Fix the table so that 40.0 dB is properly represented. Cc: Steven Toth <stoth@kernellabs.com> Signed-off-by:
-
Devin Heitmueller authored
It turns up the autodetection for the video standard in the au8522 is prone to hanging the chip until a reset is performed. This condition is trivial to reproduce simply by tuning to a station and then rapidly unplugging/ replugging the coax feed. Because we've never claimed to support anything other than NTSC-M, just disable the video-standard autodetection logic and force it to always be NTSC-M. Signed-off-by:
-
Hans Verkuil authored
All drivers that needed V4L2_FL_LOCK_ALL_FOPS have been converted, so remove this flag altogether. Signed-off-by:
-
Hans Verkuil authored
Add proper locking to the file operations, allowing for the removal of the V4L2_FL_LOCK_ALL_FOPS flag. Signed-off-by:
-
