- 05 Nov, 2014 40 commits
-
-
David Jander authored
commit 25e92445 upstream. This patch implements the workaround mentioned in ERR005829: ERR005829: FlexCAN: FlexCAN does not transmit a message that is enabled to be transmitted in a specific moment during the arbitration process. Workaround: The workaround consists of two extra steps after setting up a message for transmission: Step 8: Reserve the first valid mailbox as an inactive mailbox (CODE=0b1000). If RX FIFO is disabled, this mailbox must be message buffer 0. Otherwise, the first valid mailbox can be found using the "RX FIFO filters" table in the FlexCAN chapter of the chip reference manual. Step 9: Write twice INACTIVE code (0b1000) into the first valid mailbox. Signed-off-by:
David Jander <david@protonic.nl> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
Ben Hutchings <ben@decadent.org.uk>
-
David Jander authored
commit fc05b884 upstream. Apparently mailboxes may contain random data at startup, causing some of them being prepared for message reception. This causes overruns being missed or even confusing the IRQ check for trasmitted messages, increasing the transmit counter instead of the error counter. This patch initializes all mailboxes after the FIFO as RX_INACTIVE. Signed-off-by:
-
Marc Kleine-Budde authored
commit c32fe4ad upstream. This patch fixes the initialization of the TX mailbox. It is now correctly initialized as TX_INACTIVE not RX_EMPTY. Signed-off-by:
-
Johannes Berg authored
commit bd8c78e7 upstream. In testmode and vendor command reply/event SKBs we use the skb cb data to store nl80211 parameters between allocation and sending. This causes the code for CONFIG_NETLINK_MMAP to get confused, because it takes ownership of the skb cb data when the SKB is handed off to netlink, and it doesn't explicitly clear it. Clear the skb cb explicitly when we're done and before it gets passed to netlink to avoid this issue. Reported-by:
Assaf Azulay <assaf.azulay@intel.com> Reported-by:
David Spinadel <david.spinadel@intel.com> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Mark authored
commit c80b4495 upstream. This patch adds quirks for Entrega Technologies (later Xircom PortGear) USB- SCSI converters. They use Shuttle Technology EUSB-01/EUSB-S1 chips. The US_FL_SCM_MULT_TARG quirk is needed to allow multiple devices on the SCSI chain to be accessed. Without it only the (single) device with SCSI ID 0 can be used. The standalone converter sold by Entrega had model number U1-SC25. Xircom acquired Entrega and re-branded the product line PortGear. The PortGear USB to SCSI Converter (model PGSCSI) is internally identical to the Entrega product, but later models may use a different USB ID. The Entrega-branded units have USB ID 1645:0007, as does my Xircom PGSCSI, but the Windows and Macintosh drivers also support 085A:0028. Entrega also sold the "Mac USB Dock", which provides two USB ports, a Mac (8-pin mini-DIN) serial port and a SCSI port. It appears to the computer as a four-port hub, USB-serial, and USB-SCSI converters. The USB-SCSI part may have initially used the same ID as the standalone U1-SC25 (1645:0007), but later production used 085A:0026. My Xircom PortGear PGSCSI has bcdDevice=0x0100. Units with bcdDevice=0x0133 probably also exist. This patch adds quirks for 1645:0007, 085A:0026 and 085A:0028. The Windows driver INF file also mentions 085A:0032 "PortStation SCSI Module", but I couldn't find any mention of that actually existing in the wild; perhaps it was cancelled before release? Signed-off-by:
Mark Knibbs <markk@clara.co.uk> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Mark authored
commit b6a3ed67 upstream. Hi, The Ariston Technologies iConnect 025 and iConnect 050 (also known as e.g. iSCSI-50) are SCSI-USB converters which use Shuttle Technology/SCM Microsystems chips. Only the connectors differ; both have the same USB ID. The US_FL_SCM_MULT_TARG quirk is required to use SCSI devices with ID other than 0. I don't have one of these, but based on the other entries for Shuttle/ SCM-based converters this patch is very likely correct. I used 0x0000 and 0x9999 for bcdDeviceMin and bcdDeviceMax because I'm not sure which bcdDevice value the products use. Signed-off-by:
-
Mark authored
commit 67d365a5 upstream. The Adaptec USBConnect 2000 is another SCSI-USB converter which uses Shuttle Technology/SCM Microsystems chips. The US_FL_SCM_MULT_TARG quirk is required to use SCSI devices with ID other than 0. I don't have a USBConnect 2000, but based on the other entries for Shuttle/ SCM-based converters this patch is very likely correct. I used 0x0000 and 0x9999 for bcdDeviceMin and bcdDeviceMax because I'm not sure which bcdDevice value the product uses. Signed-off-by:
-
Mike Christie authored
commit db9bfd64 upstream. This patches fixes a potential buffer overrun in __iscsi_conn_send_pdu. This function is used by iscsi drivers and userspace to send iscsi PDUs/ commands. For login commands, we have a set buffer size. For all other commands we do not support data buffers. This was reported by Dan Carpenter here: http://www.spinics.net/lists/linux-scsi/msg66838.htmlReported-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Mike Christie <michaelc@cs.wisc.edu> Reviewed-by:
Sagi Grimberg <sagig@mellanox.com> Signed-off-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
James Bottomley <JBottomley@Parallels.com> Signed-off-by:
-
Trond Myklebust authored
commit cd9288ff upstream. James Drew reports another bug whereby the NFS client is now sending an OPEN_DOWNGRADE in a situation where it should really have sent a CLOSE: the client is opening the file for O_RDWR, but then trying to do a downgrade to O_RDONLY, which is not allowed by the NFSv4 spec. Reported-by:
James Drews <drews@engr.wisc.edu> Link: http://lkml.kernel.org/r/541AD7E5.8020409@engr.wisc.edu Fixes: aee7af35 (NFSv4: Fix problems with close in the presence...) Signed-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Joern Engel authored
commit 8ae757d0 upstream. In iscsi_copy_param_list() a failed iscsi_param_list memory allocation currently invokes iscsi_release_param_list() to cleanup, and will promptly trigger a NULL pointer dereference. Instead, go ahead and return for the first iscsi_copy_param_list() failure case. Found by coverity. Signed-off-by:
Joern Engel <joern@logfs.org> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Nicholas Bellinger authored
commit b53b0d99 upstream. This patch fixes a bug in iscsit_logout_post_handler_diffcid() where a pointer used as storage for list_for_each_entry() was incorrectly being used to determine if no matching entry had been found. This patch changes iscsit_logout_post_handler_diffcid() to key off bool conn_found to determine if the function needs to exit early. Reported-by:
-
Al Viro authored
commit 4023bfc9 upstream. in the former we simply check if dentry is still valid after picking its ->d_inode; in the latter we fetch ->d_inode in the same places where we fetch dentry and its ->d_seq, under the same checks. Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Ben Hutchings authored
This is needed before commit 4023bfc9 ('be careful with nd->inode in path_init() and follow_dotdot_rcu()'). A similar change was made upstream as part of commit b37199e6 ('rcuwalk: recheck mount_lock after mountpoint crossing attempts'). Signed-off-by:
-
Al Viro authored
commit 7bd88377 upstream. return the value instead, and have path_init() do the assignment. Broken by "vfs: Fix absolute RCU path walk failures due to uninitialized seq number", which was Cc-stable with 2.6.38+ as destination. This one should go where it went. To avoid dummy value returned in case when root is already set (it would do no harm, actually, since the only caller that doesn't ignore the return value is guaranteed to have nd->root *not* set, but it's more obvious that way), lift the check into callers. And do the same to set_root(), to keep them in sync. Signed-off-by:
-
Richard Larocque authored
commit 474e941b upstream. Locks the k_itimer's it_lock member when handling the alarm timer's expiry callback. The regular posix timers defined in posix-timers.c have this lock held during timout processing because their callbacks are routed through posix_timer_fn(). The alarm timers follow a different path, so they ought to grab the lock somewhere else. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Sharvil Nanavati <sharvil@google.com> Signed-off-by:
Richard Larocque <rlarocque@google.com> Signed-off-by:
John Stultz <john.stultz@linaro.org> Signed-off-by:
-
Richard Larocque authored
commit 265b81d2 upstream. Avoids sending a signal to alarm timers created with sigev_notify set to SIGEV_NONE by checking for that special case in the timeout callback. The regular posix timers avoid sending signals to SIGEV_NONE timers by not scheduling any callbacks for them in the first place. Although it would be possible to do something similar for alarm timers, it's simpler to handle this as a special case in the timeout. Prior to this patch, the alarm timer would ignore the sigev_notify value and try to deliver signals to the process anyway. Even worse, the sanity check for the value of sigev_signo is skipped when SIGEV_NONE was specified, so the signal number could be bogus. If sigev_signo was an unitialized value (as it often would be if SIGEV_NONE is used), then it's hard to predict which signal will be sent. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Sharvil Nanavati <sharvil@google.com> Signed-off-by:
-
Richard Larocque authored
commit e86fea76 upstream. Returns the time remaining for an alarm timer, rather than the time at which it is scheduled to expire. If the timer has already expired or it is not currently scheduled, the it_value's members are set to zero. This new behavior matches that of the other posix-timers and the POSIX specifications. This is a change in user-visible behavior, and may break existing applications. Hopefully, few users rely on the old incorrect behavior. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@kernel.org> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Prarit Bhargava <prarit@redhat.com> Cc: Sharvil Nanavati <sharvil@google.com> Signed-off-by:
-
Andrew Hunter authored
commit d78c9300 upstream. timeval_to_jiffies tried to round a timeval up to an integral number of jiffies, but the logic for doing so was incorrect: intervals corresponding to exactly N jiffies would become N+1. This manifested itself particularly repeatedly stopping/starting an itimer: setitimer(ITIMER_PROF, &val, NULL); setitimer(ITIMER_PROF, NULL, &val); would add a full tick to val, _even if it was exactly representable in terms of jiffies_ (say, the result of a previous rounding.) Doing this repeatedly would cause unbounded growth in val. So fix the math. Here's what was wrong with the conversion: we essentially computed (eliding seconds) jiffies = usec * (NSEC_PER_USEC/TICK_NSEC) by using scaling arithmetic, which took the best approximation of NSEC_PER_USEC/TICK_NSEC with denominator of 2^USEC_JIFFIE_SC = x/(2^USEC_JIFFIE_SC), and computed: jiffies = (usec * x) >> USEC_JIFFIE_SC and rounded this calculation up in the intermediate form (since we can't necessarily exactly represent TICK_NSEC in usec.) But the scaling arithmetic is a (very slight) *over*approximation of the true value; that is, instead of dividing by (1 usec/ 1 jiffie), we effectively divided by (1 usec/1 jiffie)-epsilon (rounding down). This would normally be fine, but we want to round timeouts up, and we did so by adding 2^USEC_JIFFIE_SC - 1 before the shift; this would be fine if our division was exact, but dividing this by the slightly smaller factor was equivalent to adding just _over_ 1 to the final result (instead of just _under_ 1, as desired.) In particular, with HZ=1000, we consistently computed that 10000 usec was 11 jiffies; the same was true for any exact multiple of TICK_NSEC. We could possibly still round in the intermediate form, adding something less than 2^USEC_JIFFIE_SC - 1, but easier still is to convert usec->nsec, round in nanoseconds, and then convert using time*spec*_to_jiffies. This adds one constant multiplication, and is not observably slower in microbenchmarks on recent x86 hardware. Tested: the following program: int main() { struct itimerval zero = {{0, 0}, {0, 0}}; /* Initially set to 10 ms. */ struct itimerval initial = zero; initial.it_interval.tv_usec = 10000; setitimer(ITIMER_PROF, &initial, NULL); /* Save and restore several times. */ for (size_t i = 0; i < 10; ++i) { struct itimerval prev; setitimer(ITIMER_PROF, &zero, &prev); /* on old kernels, this goes up by TICK_USEC every iteration */ printf("previous value: %ld %ld %ld %ld\n", prev.it_interval.tv_sec, prev.it_interval.tv_usec, prev.it_value.tv_sec, prev.it_value.tv_usec); setitimer(ITIMER_PROF, &prev, NULL); } return 0; } Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Ingo Molnar <mingo@redhat.com> Cc: Paul Turner <pjt@google.com> Cc: Richard Cochran <richardcochran@gmail.com> Cc: Prarit Bhargava <prarit@redhat.com> Reviewed-by:
Paul Turner <pjt@google.com> Reported-by:
Aaron Jacobs <jacobsa@google.com> Signed-off-by:
Andrew Hunter <ahh@google.com> [jstultz: Tweaked to apply to 3.17-rc] Signed-off-by:
-
Thomas Gleixner authored
commit 13c42c2f upstream. futex_wait_requeue_pi() calls futex_wait_setup(). If futex_wait_setup() succeeds it returns with hb->lock held and preemption disabled. Now the sanity check after this does: if (match_futex(&q.key, &key2)) { ret = -EINVAL; goto out_put_keys; } which releases the keys but does not release hb->lock. So we happily return to user space with hb->lock held and therefor preemption disabled. Unlock hb->lock before taking the exit route. Reported-by:
Dave "Trinity" Jones <davej@redhat.com> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Reviewed-by:
Darren Hart <dvhart@linux.intel.com> Reviewed-by:
Davidlohr Bueso <dave@stgolabs.net> Cc: Peter Zijlstra <a.p.zijlstra@chello.nl> Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1409112318500.4178@nanosSigned-off-by:
-
Hans de Goede authored
commit d2682118 upstream. The sys_vendor / product_name are somewhat generic unfortunately, so this may lead to some false positives. But nomux usually does no harm, where as not having it clearly is causing problems on the Avatar AVIU-145A6. https://bugzilla.kernel.org/show_bug.cgi?id=77391Reported-by:
Hugo P <saurosii@gmail.com> Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Hans de Goede authored
commit cc18a69c upstream. https://bugzilla.kernel.org/show_bug.cgi?id=69731Reported-by:
Jason Robinson <mail@jasonrobinson.me> Signed-off-by:
-
Mathias Nyman authored
commit c207e7c5 upstream. If xhci initialization fails before the roothub bandwidth domains (xhci->rh_bw[i]) are allocated it will oops when trying to access rh_bw members in xhci_mem_cleanup(). Reported-by:
Manuel Reimer <manuel.reimer@gmx.de> Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Mark authored
commit c66f1c62 upstream. The Iomega Jaz USB Adapter is a SCSI-USB converter cable. The hardware seems to be identical to e.g. the Microtech XpressSCSI, using a Shuttle/ SCM chip set. However its firmware restricts it to only work with Jaz drives. On connecting the cable a message like this appears four times in the log: reset full speed USB device number 4 using uhci_hcd That's non-fatal but the US_FL_SINGLE_LUN quirk fixes it. Signed-off-by:
-
Joe Lawrence authored
commit c605f3cd upstream. During surprise device hotplug removal tests, it was observed that hub_events may try to call usb_lock_device on a device that has already been freed. Protect the usb_device by taking out a reference (under the hub_event_lock) when hub_events pulls it off the list, returning the reference after hub_events is finished using it. Signed-off-by:
Joe Lawrence <joe.lawrence@stratus.com> Suggested-by: David Bulkow <david.bulkow@stratus.com> for using kref Suggested-by: Alan Stern <stern@rowland.harvard.edu> for placement Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
John Sung authored
commit a80d8b02 upstream. When running a 32-bit inputattach utility in a 64-bit system, there will be error code "inputattach: can't set device type". This is caused by the serport device driver not supporting compat_ioctl, so that SPIOCSTYPE ioctl fails. Signed-off-by:
John Sung <penmount.touch@gmail.com> Signed-off-by:
-
Ilya Dryomov authored
commit c27a3e4d upstream. We hard code cephx auth ticket buffer size to 256 bytes. This isn't enough for any moderate setups and, in case tickets themselves are not encrypted, leads to buffer overflows (ceph_x_decrypt() errors out, but ceph_decode_copy() doesn't - it's just a memcpy() wrapper). Since the buffer is allocated dynamically anyway, allocated it a bit later, at the point where we know how much is going to be needed. Fixes: http://tracker.ceph.com/issues/8979Signed-off-by:
Ilya Dryomov <ilya.dryomov@inktank.com> Reviewed-by:
Sage Weil <sage@redhat.com> Signed-off-by:
-
Ilya Dryomov authored
commit 597cda35 upstream. Add a helper for processing individual cephx auth tickets. Needed for the next commit, which deals with allocating ticket buffers. (Most of the diff here is whitespace - view with git diff -b). Signed-off-by:
-
Sage Weil authored
commit 73c3d481 upstream. We preallocate a few of the message types we get back from the mon. If we get a larger message than we are expecting, fall back to trying to allocate a new one instead of blindly using the one we have. Signed-off-by:
-
Ilya Dryomov authored
commit 3cea4c30 upstream. Rename front_max field of struct ceph_msg to front_alloc_len to make its purpose more clear. Signed-off-by:
Sage Weil <sage@inktank.com> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Dmitry Torokhov authored
commit 5715fc76 upstream. ForcePads are found on HP EliteBook 1040 laptops. They lack any kind of physical buttons, instead they generate primary button click when user presses somewhat hard on the surface of the touchpad. Unfortunately they also report primary button click whenever there are 2 or more contacts on the pad, messing up all multi-finger gestures (2-finger scrolling, multi-finger tapping, etc). To cope with this behavior we introduce a delay (currently 50 msecs) in reporting primary press in case more contacts appear. Reviewed-by:
-
Cong Wang authored
commit 3577af70 upstream. We saw a kernel soft lockup in perf_remove_from_context(), it looks like the `perf` process, when exiting, could not go out of the retry loop. Meanwhile, the target process was forking a child. So either the target process should execute the smp function call to deactive the event (if it was running) or it should do a context switch which deactives the event. It seems we optimize out a context switch in perf_event_context_sched_out(), and what's more important, we still test an obsolete task pointer when retrying, so no one actually would deactive that event in this situation. Fix it directly by reloading the task pointer in perf_remove_from_context(). This should cure the above soft lockup. Signed-off-by:
Cong Wang <cwang@twopensource.com> Signed-off-by:
Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by:
Peter Zijlstra <peterz@infradead.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Link: http://lkml.kernel.org/r/1409696840-843-1-git-send-email-xiyou.wangcong@gmail.comSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Thomas Pugliese authored
commit 675f0ab2 upstream. Make sure the uwb_dev->bce entry is set before calling uwb_dev_add in uwbd_dev_onair so that usermode will only see the device after it is properly initialized. This fixes a kernel panic that can occur if usermode tries to access the IEs sysfs attribute of a UWB device before the driver has had a chance to set the beacon cache entry. Signed-off-by:
Thomas Pugliese <thomas.pugliese@gmail.com> Signed-off-by:
-
Taylor Braun-Jones authored
commit 9c491c37 upstream. Signed-off-by:
Taylor Braun-Jones <taylor.braun-jones@ge.com> Cc: Johan Hovold <johan@kernel.org> Signed-off-by:
-
Hans de Goede authored
commit 271329b3 upstream. Adjust Elantech signature validation to account fo rnewer models of touchpads. Reported-and-tested-by:
Màrius Monton <marius.monton@gmail.com> Signed-off-by:
-
Felipe Balbi authored
commit 96908589 upstream. Commit 71c731a2 (usb: host: xhci: Fix Compliance Mode on SN65LVP3502CP Hardware) implemented a workaround for a known issue with Texas Instruments' USB 3.0 redriver IC but it left a condition where any xHCI host would be taken out of reset if port was placed in compliance mode and there was no device connected to the port. That condition would trigger a fake connection to a non-existent device so that usbcore would trigger a warm reset of the port, thus taking the link out of reset. This has the side-effect of preventing any xHCI host connected to a Linux machine from starting and running the USB 3.0 Electrical Compliance Suite because the port will mysteriously taken out of compliance mode and, thus, xHCI won't step through the necessary compliance patterns for link validation. This patch fixes the issue by just adding a missing check for XHCI_COMP_MODE_QUIRK inside xhci_hub_report_usb3_link_state() when PORT_CAS isn't set. This patch should be backported to all kernels containing commit 71c731a2. Fixes: 71c731a2 (usb: host: xhci: Fix Compliance Mode on SN65LVP3502CP Hardware) Cc: Alexis R. Cortes <alexis.cortes@ti.com> Signed-off-by:
Felipe Balbi <balbi@ti.com> Acked-by:
-
Alex Deucher authored
commit 1952f24d upstream. Vbios connector table lists non-existent VGA port. Bug: https://bugs.freedesktop.org/show_bug.cgi?id=83184Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Murali Karicheri authored
commit c5edfff9 upstream. Keystone K2E EVM uses Marvel 0x9182 controller. This requires support for the ID in the ahci driver. Signed-off-by:
Murali Karicheri <m-karicheri2@ti.com> Signed-off-by:
Tejun Heo <tj@kernel.org> Cc: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by:
-
Felipe Balbi authored
commit fed33afc upstream. Currently, we disable pm_runtime before all register accesses are done, this is dangerous and might lead to abort exceptions due to the driver trying to access a register which is clocked by a clock which was long gated. Fix that by moving pm_runtime_put_sync() and pm_runtime_disable() as the last thing we do before returning from our ->remove() method. Fixes: 72246da4 (usb: Introduce DesignWare USB3 DRD Driver) Signed-off-by:
-
Felipe Balbi authored
commit 16b972a5 upstream. We are going to disable runtime_pm and we're removing the driver, we must disable the device now. Signed-off-by:
-
Jiri Kosina authored
commit 6726655d upstream. There is a following AB-BA dependency between cpu_hotplug.lock and cpuidle_lock: 1) cpu_hotplug.lock -> cpuidle_lock enable_nonboot_cpus() _cpu_up() cpu_hotplug_begin() LOCK(cpu_hotplug.lock) cpu_notify() ... acpi_processor_hotplug() cpuidle_pause_and_lock() LOCK(cpuidle_lock) 2) cpuidle_lock -> cpu_hotplug.lock acpi_os_execute_deferred() workqueue ... acpi_processor_cst_has_changed() cpuidle_pause_and_lock() LOCK(cpuidle_lock) get_online_cpus() LOCK(cpu_hotplug.lock) Fix this by reversing the order acpi_processor_cst_has_changed() does thigs -- let it first execute the protection against CPU hotplug by calling get_online_cpus() and obtain the cpuidle lock only after that (and perform the symmentric change when allowing CPUs hotplug again and dropping cpuidle lock). Spotted by lockdep. Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
