- 06 Sep, 2018 4 commits
-
-
Govind Singh authored
WCN3990 target uses separate htc service for pktlog. Add pktlog service request and support for pktlog rx path handling. Testing: Tested on WCN3990 and QCA6174 HW. Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1, WLAN.RM.4.4.1-00109-QCARMSWPZ-1 Signed-off-by: Govind Singh <govinds@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Govind Singh authored
Existing copy engine interrupt enable logic assumes that last CE is using polling mode and due to this interrupt for last copy engine are always disabled. WCN3990 uses last CE for pktlog and interrupt remains disabled with existing logic. To mitigate this issue, introduce CE_ATTR_POLL flag and control the interrupt based on the flag which can be set in ce_attr. Testing: Tested on WCN3990 and QCA6174 HW. Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1, WLAN.RM.4.4.1-00109-QCARMSWPZ-1 Signed-off-by: Govind Singh <govinds@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Sathishkumar Muruganandam authored
To support dual-band variant of QCA9984, new extended board data (eBDF) is introduced since existing board data ran out of space. Below is the brief implementation & design detail, ---------------------------------------------------- 1. New OTP changes to inform eBDF support in existing OTP download to fetch board ID and chip ID. This is backward compatible and older card sends 0 by default for eBDF support bit (bit 18 of OTP response) we check in ath10k driver. 2. If eBDF is supported, then we need to fetch eBDF ID which is bundled in downloaded board data. So again OTP is executed for knowing the eBDF ID. This is done once we set 'board_data_initialized' bit. If eBDF ID returned is zero, we continue booting with previous board data downloaded. 3. Based on the eBDF ID fetched, ath10k driver tries to download the extended board data to a new offset ahead of already downloaded board data address. 4. A new BD IE type, ATH10K_BD_IE_BOARD_EXT is added to differentiate in bundling eBDF separately in board-2.bin and also to parse through board bundle for eBDF download in ath10k boot. 5. If eBDF is not present in the board-2.bin bundle or when board ID is zero, we do a fallback boot to "eboard.bin" in the same QCA9984/hw1.0 dir. This is same as done to existing "board.bin" if board ID is not present in board-2.bin bundle. Current design is that eBDF size will be 2KB and eBDF ID will be byte value. Tested the above changes with dual-band variant of QCA9984 card. OTP update needed for the test will be part of next FW release 10.4-3.6-xxxx. Below are the logs with ath10k BOOT debugs enabled. First OTP response : --------------------- .. boot upload otp to 0x1234 len 9478 for board id boot get otp board id result 0x00040400 board_id 1 chip_id 0 ext_bid_support 1 .. Second OTP response : --------------------- .. boot upload otp to 0x1234 len 9478 for ext board id boot get otp ext board id result 0x00000005 ext_board_id 5 boot using eboard name 'bus=pci,bmi-chip-id=0,bmi-eboard-id=5' .. Extended board data download: ------------------------------ .. board name 00000000: 62 75 73 3d 70 63 69 2c 62 6d 69 2d 63 68 69 70 bus=pci,bmi-chip 00000010: 2d 69 64 3d 30 2c 62 6d 69 2d 65 62 6f 61 72 64 -id=0,bmi-eboard 00000020: 2d 69 64 3d 35 -id=5 boot found match for name 'bus=pci,bmi-chip-id=0,bmi-eboard-id=5' boot found eboard data for 'bus=pci,bmi-chip-id=0,bmi-eboard-id=5' using board api 2 boot writing ext board data to addr 0xc3000 .. Fallback Extended board data download from "eboard.bin": --------------------------------------------------------- .. board name 00000000: 62 75 73 3d 70 63 69 2c 62 6d 69 2d 63 68 69 70 bus=pci,bmi-chip 00000010: 2d 69 64 3d 30 2c 62 6d 69 2d 62 6f 61 72 64 2d -id=0,bmi-board- 00000020: 69 64 3d 31 30 id=10 failed to fetch board data for bus=pci,bmi-chip-id=0,bmi-eboard-id=5 from ath10k/QCA9984/hw1.0/board-2.bin boot fw request 'ath10k/QCA9984/hw1.0/eboard.bin': 0 using board api 1 boot writing ext board data to addr 0xc3000 .. Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Sathishkumar Muruganandam authored
Just moving functions down in the file, no functional changes. Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
- 03 Sep, 2018 4 commits
-
-
Niklas Cassel authored
ATH10K_SNOC builds just fine with COMPILE_TEST, so make that possible. Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Rob Herring authored
In preparation to remove the node name pointer from struct device_node, convert printf users to use the %pOFn format specifier. Cc: Kalle Valo <kvalo@codeaurora.org> Cc: "David S. Miller" <davem@davemloft.net> Cc: linux-wireless@vger.kernel.org Cc: netdev@vger.kernel.org Signed-off-by: Rob Herring <robh@kernel.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Wen Gong authored
If there are some tx packets pending in firmware, and then system enters suspend, firmware will fail for wow enable. This will trigger mac80211 to stop ath10k and download firmware again, then it is non-wow suspend. After add the waiting htt tx complete, then firmware will have some time window to send or flush the pending tx packets. Tested with QCA6174 PCI with firmware WLAN.RM.4.4.1-00109-QCARMSWPZ-1, but this will also affect QCA9377 PCI. It's not a regression with new firmware releases. Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Brian Norris authored
Devices may provide their own MAC address via system firmware (e.g., device tree), especially in the case where the device doesn't have a useful EEPROM on which to store its MAC address (e.g., for integrated Wifi). Use the generic device helper to retrieve the MAC address, and (if present) honor it above the MAC address advertised by the card. Signed-off-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
- 28 Aug, 2018 18 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.gitKalle Valo authored
ath.git patches for 4.20. Major changes: ath10k * limit available channels via DT ieee80211-freq-limit wil6210 * add 802.11r Fast Roaming support for AP and station modes * add support for channel 4
-
Sven Eckelmann authored
Tri-band devices (1x 2.4GHz + 2x 5GHz) often incorporate special filters in the RX and TX path. These filtered channel can in theory still be used by the hardware but the signal strength is reduced so much that it makes no sense. There is already a DT property to limit the available channels but ath10k has to manually call this functionality to limit the currrently set wiphy channels further. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Dedy Lansky authored
Check rx_buff_mgmt is allocated before accessing its internal fields. Signed-off-by: Dedy Lansky <dlansky@codeaurora.org> Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Ahmad Masri authored
This feature is needed for enterprise APs and clients to enable fast roaming as defined in 802.11r between APs in the same ESS. On AP side, this feature is supported only when disable_ap_sme is enabled. Signed-off-by: Ahmad Masri <amasri@codeaurora.org> Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Maya Erez authored
RX SKBs are released in both wil6210 rmmod and RX handle. As there is no lock to protect the buffers DMA unmap, the SKB pointer in buff_arr is used to check if the buffer memory was already released. Setting wil->rx_buff_mgmt.buff_arr[buff_id].skb to NULL before the DMA memory unmap will prevent duplicate unmapping of the same memory. Move the buffer ID to the free list also in case the SKB is NULL. Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Maya Erez authored
In enhanced DMA ring 0 is used for RX ring, hence TX ring 0 is an unused element in ring_tx and ring2cid_tid arrays. Initialize ring2cid_tid CID to WIL6210_MAX_CID to prevent a false match of CID 0. Go over the ring_tx and ring2cid_tid from wil_get_min_tx_ring_id and on to prevent access to index 0 in eDMA. Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Maya Erez authored
wil_addba_rx_request allocates the rx reorder buffer regardless of use_rx_hw_reordering settings. Fix this by checking wil->use_rx_hw_reordering before allocating the reorder buffer. Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Maya Erez authored
use_rx_hw_reordering is already set to true in wil_set_capabilities for Talyn-MB devices. Remove its setting from wil_priv_init to prevent its activation for older chips. Similarly, move the setting of use_compressed_rx_status to wil_set_capabilities. Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Dedy Lansky authored
Delivering a looped-back multicast packet to network stack can cause higher layer protocols to fail like for example IPv6 DAD. In STA mode, upon receiving Rx multicast packet, check if the source MAC address is equal to our own MAC address and if so drop the packet. Signed-off-by: Dedy Lansky <dlansky@codeaurora.org> Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Alexei Avshalom Lazar authored
wil6210 supports channels 1-3 of the 60GHz band. New FW added support for channel 4. Add support for channel 4 also in wil6210 driver. Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org> Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Karthick Gopalasubramanian authored
Reset file is not used and may cause race conditions with operational driver if used. Signed-off-by: Karthick Gopalasubramanian <kargop@codeaurora.org> Signed-off-by: Maya Erez <merez@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Varsha Rao authored
Remove extra parentheses to fix the clang warning of extraneous parentheses. Signed-off-by: Varsha Rao <rvarsha016@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Felix Fietkau authored
Tx99 is typically configured via a monitor mode interface, which does not get added to the driver as a vif. Since the code currently expects a configured virtual interface for tx99, enabling tx99 via debugfs fails. Since the vif is not needed anyway, remove all checks for it. Signed-off-by: Felix Fietkau <nbd@nbd.name> [kvalo@codeaurora.org: s/CPTCFG/CONFIG/] Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Colin Ian King authored
Array firstep_table is being assigned but is never used hence it is redundant and can be removed. Cleans up clang warning: warning: 'firstep_table' defined but not used [-Wunused-const-variable=] Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Varsha Rao authored
Remove extra parentheses to fix the clang warning of extraneous parentheses. Signed-off-by: Varsha Rao <rvarsha016@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Gustavo A. R. Silva authored
One of the more common cases of allocation size calculations is finding the size of a structure that has a zero-sized array at the end, along with memory for some number of elements for that array. For example: struct foo { int stuff; void *entry[]; }; instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL); Instead of leaving these open-coded and prone to type mistakes, we can now use the new struct_size() helper: instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL); This issue was detected with the help of Coccinelle. Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Reviewed-by: Kees Cook <keescook@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Martin Willi authored
When running in AP mode, ath10k sometimes suffers from TX credit starvation. The issue is hard to reproduce and shows up once in a few days, but has been repeatedly seen with QCA9882 and a large range of firmwares, including 10.2.4.70.67. Once the module is in this state, TX credits are never replenished, which results in "SWBA overrun" errors, as no beacons can be sent. Even worse, WMI commands run in a timeout while holding the conf mutex for three seconds each, making any further operations slow and the whole system unresponsive. The firmware/driver never recovers from that state automatically, and triggering TX flush or warm restarts won't work over WMI. So issue a hardware restart if a WMI command times out due to missing TX credits. This implies a connectivity outage of about 1.4s in AP mode, but brings back the interface and the whole system to a usable state. WMI command timeouts have not been seen in absent of this specific issue, so taking such drastic actions seems legitimate. Signed-off-by: Martin Willi <martin@strongswan.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
Rakesh Pillai authored
WCN3990 has the MAC_PCU_ADDR1 configured properly and hence it will not send spurious ack frames during boot up. Hence the reset_rx_filter workaround is not needed for WCN3990. Add a hw_param to indicate if hardware rx filter reset is needed and skip the reset_rx_filter for WCN3990. Tested HW: WCN3990 Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1 Signed-off-by: Rakesh Pillai <pillair@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
-
- 27 Aug, 2018 2 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds authored
Pull networking fixes from David Miller: 1) ICE, E1000, IGB, IXGBE, and I40E bug fixes from the Intel folks. 2) Better fix for AB-BA deadlock in packet scheduler code, from Cong Wang. 3) bpf sockmap fixes (zero sized key handling, etc.) from Daniel Borkmann. 4) Send zero IPID in TCP resets and SYN-RECV state ACKs, to prevent attackers using it as a side-channel. From Eric Dumazet. 5) Memory leak in mediatek bluetooth driver, from Gustavo A. R. Silva. 6) Hook up rt->dst.input of ipv6 anycast routes properly, from Hangbin Liu. 7) hns and hns3 bug fixes from Huazhong Tan. 8) Fix RIF leak in mlxsw driver, from Ido Schimmel. 9) iova range check fix in vhost, from Jason Wang. 10) Fix hang in do_tcp_sendpages() with tls, from John Fastabend. 11) More r8152 chips need to disable RX aggregation, from Kai-Heng Feng. 12) Memory exposure in TCA_U32_SEL handling, from Kees Cook. 13) TCP BBR congestion control fixes from Kevin Yang. 14) hv_netvsc, ignore non-PCI devices, from Stephen Hemminger. 15) qed driver fixes from Tomer Tayar. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (77 commits) net: sched: Fix memory exposure from short TCA_U32_SEL qed: fix spelling mistake "comparsion" -> "comparison" vhost: correctly check the iova range when waking virtqueue qlge: Fix netdev features configuration. net: macb: do not disable MDIO bus at open/close time Revert "net: stmmac: fix build failure due to missing COMMON_CLK dependency" net: macb: Fix regression breaking non-MDIO fixed-link PHYs mlxsw: spectrum_switchdev: Do not leak RIFs when removing bridge i40e: fix condition of WARN_ONCE for stat strings i40e: Fix for Tx timeouts when interface is brought up if DCB is enabled ixgbe: fix driver behaviour after issuing VFLR ixgbe: Prevent unsupported configurations with XDP ixgbe: Replace GFP_ATOMIC with GFP_KERNEL igb: Replace mdelay() with msleep() in igb_integrated_phy_loopback() igb: Replace GFP_ATOMIC with GFP_KERNEL in igb_sw_init() igb: Use an advanced ctx descriptor for launchtime e1000: ensure to free old tx/rx rings in set_ringparam() e1000: check on netif_running() before calling e1000_up() ixgb: use dma_zalloc_coherent instead of allocator/memset ice: Trivial formatting fixes ...
-
Jens Axboe authored
The email was botched in one entry, and I also forgot to update the location of the git tree. It'll be under the linux-block umbrella, just with different branches. Reported-by: Baruch Siach <baruch@tkos.co.il> Fixes: 7634ccd2 ("libata: maintainership update") Signed-off-by: Jens Axboe <axboe@kernel.dk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
- 26 Aug, 2018 12 commits
-
-
Kees Cook authored
Via u32_change(), TCA_U32_SEL has an unspecified type in the netlink policy, so max length isn't enforced, only minimum. This means nkeys (from userspace) was being trusted without checking the actual size of nla_len(), which could lead to a memory over-read, and ultimately an exposure via a call to u32_dump(). Reachability is CAP_NET_ADMIN within a namespace. Reported-by: Al Viro <viro@zeniv.linux.org.uk> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Cc: Cong Wang <xiyou.wangcong@gmail.com> Cc: Jiri Pirko <jiri@resnulli.us> Cc: "David S. Miller" <davem@davemloft.net> Cc: netdev@vger.kernel.org Signed-off-by: Kees Cook <keescook@chromium.org> Acked-by: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull timer update from Thomas Gleixner: "New defines for the compat time* types so they can be shared between 32bit and 64bit builds. Not used yet, but merging them now allows the actual conversions to be merged through different maintainer trees without dependencies We still have compat interfaces for 32bit on 64bit even with the new 2038 safe timespec/val variants because pointer size is different. And for the old style timespec/val interfaces we need yet another 'compat' interface for both 32bit native and 32bit on 64bit" * 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: y2038: Provide aliases for compat helpers
-
git://git.infradead.org/users/willy/linux-daxLinus Torvalds authored
Pull IDA updates from Matthew Wilcox: "A better IDA API: id = ida_alloc(ida, GFP_xxx); ida_free(ida, id); rather than the cumbersome ida_simple_get(), ida_simple_remove(). The new IDA API is similar to ida_simple_get() but better named. The internal restructuring of the IDA code removes the bitmap preallocation nonsense. I hope the net -200 lines of code is convincing" * 'ida-4.19' of git://git.infradead.org/users/willy/linux-dax: (29 commits) ida: Change ida_get_new_above to return the id ida: Remove old API test_ida: check_ida_destroy and check_ida_alloc test_ida: Convert check_ida_conv to new API test_ida: Move ida_check_max test_ida: Move ida_check_leaf idr-test: Convert ida_check_nomem to new API ida: Start new test_ida module target/iscsi: Allocate session IDs from an IDA iscsi target: fix session creation failure handling drm/vmwgfx: Convert to new IDA API dmaengine: Convert to new IDA API ppc: Convert vas ID allocation to new IDA API media: Convert entity ID allocation to new IDA API ppc: Convert mmu context allocation to new IDA API Convert net_namespace to new IDA API cb710: Convert to new IDA API rsxx: Convert to new IDA API osd: Convert to new IDA API sd: Convert to new IDA API ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linuxLinus Torvalds authored
Pull gcc plugin fix from Kees Cook: "Lift gcc test into Kconfig. This is for better behavior when the kernel is built with Clang, reported by Stefan Agner" * tag 'gcc-plugins-v4.19-rc1-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: gcc-plugins: Disable when building under Clang
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull perf updates from Thomas Gleixner: "Kernel: - Improve kallsyms coverage - Add x86 entry trampolines to kcore - Fix ARM SPE handling - Correct PPC event post processing Tools: - Make the build system more robust - Small fixes and enhancements all over the place - Update kernel ABI header copies - Preparatory work for converting libtraceevnt to a shared library - License cleanups" * 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (100 commits) tools arch: Update arch/x86/lib/memcpy_64.S copy used in 'perf bench mem memcpy' tools arch x86: Update tools's copy of cpufeatures.h perf python: Fix pyrf_evlist__read_on_cpu() interface perf mmap: Store real cpu number in 'struct perf_mmap' perf tools: Remove ext from struct kmod_path perf tools: Add gzip_is_compressed function perf tools: Add lzma_is_compressed function perf tools: Add is_compressed callback to compressions array perf tools: Move the temp file processing into decompress_kmodule perf tools: Use compression id in decompress_kmodule() perf tools: Store compression id into struct dso perf tools: Add compression id into 'struct kmod_path' perf tools: Make is_supported_compression() static perf tools: Make decompress_to_file() function static perf tools: Get rid of dso__needs_decompress() call in __open_dso() perf tools: Get rid of dso__needs_decompress() call in symbol__disassemble() perf tools: Get rid of dso__needs_decompress() call in read_object_code() tools lib traceevent: Change to SPDX License format perf llvm: Allow passing options to llc in addition to clang perf parser: Improve error message for PMU address filters ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull x86 fixes from Thomas Gleixner: - Correct the L1TF fallout on 32bit and the off by one in the 'too much RAM for protection' calculation. - Add a helpful kernel message for the 'too much RAM' case - Unbreak the VDSO in case that the compiler desides to use indirect jumps/calls and emits retpolines which cannot be resolved because the kernel uses its own thunks, which does not work for the VDSO. Make it use the builtin thunks. - Re-export start_thread() which was unexported when the 32/64bit implementation was unified. start_thread() is required by modular binfmt handlers. - Trivial cleanups * 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/speculation/l1tf: Suggest what to do on systems with too much RAM x86/speculation/l1tf: Fix off-by-one error when warning that system has too much RAM x86/kvm/vmx: Remove duplicate l1d flush definitions x86/speculation/l1tf: Fix overflow in l1tf_pfn_limit() on 32bit x86/process: Re-export start_thread() x86/mce: Add notifier_block forward declaration x86/vdso: Fix vDSO build if a retpoline is emitted
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull irq update from Thomas Gleixner: "A small set of updats/fixes for the irq subsystem: - Allow GICv3 interrupts to be configured as wake-up sources to enable wakeup from suspend - Make the error handling of the STM32 irqchip init function work - A set of small cleanups and improvements" * 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: irqchip/gic-v3: Allow interrupt to be configured as wake-up sources irqchip/tango: Set irq handler and data in one go dt-bindings: irqchip: renesas-irqc: Document r8a774a1 support irqchip/s3c24xx: Remove unneeded comparison of unsigned long to 0 irqchip/stm32: Fix init error handling irqchip/bcm7038-l1: Hide cpu offline callback when building for !SMP
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull licking update from Thomas Gleixner: "Mark the switch cases which fall through to the next case with the proper comment so the fallthrough compiler checks can be enabled" * 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: futex: Mark expected switch fall-throughs
-
Linus Torvalds authored
Merge tag 'libnvdimm-for-4.19_dax-memory-failure' of gitolite.kernel.org:pub/scm/linux/kernel/git/nvdimm/nvdimm Pull libnvdimm memory-failure update from Dave Jiang: "As it stands, memory_failure() gets thoroughly confused by dev_pagemap backed mappings. The recovery code has specific enabling for several possible page states and needs new enabling to handle poison in dax mappings. In order to support reliable reverse mapping of user space addresses: 1/ Add new locking in the memory_failure() rmap path to prevent races that would typically be handled by the page lock. 2/ Since dev_pagemap pages are hidden from the page allocator and the "compound page" accounting machinery, add a mechanism to determine the size of the mapping that encompasses a given poisoned pfn. 3/ Given pmem errors can be repaired, change the speculatively accessed poison protection, mce_unmap_kpfn(), to be reversible and otherwise allow ongoing access from the kernel. A side effect of this enabling is that MADV_HWPOISON becomes usable for dax mappings, however the primary motivation is to allow the system to survive userspace consumption of hardware-poison via dax. Specifically the current behavior is: mce: Uncorrected hardware memory error in user-access at af34214200 {1}[Hardware Error]: It has been corrected by h/w and requires no further action mce: [Hardware Error]: Machine check events logged {1}[Hardware Error]: event severity: corrected Memory failure: 0xaf34214: reserved kernel page still referenced by 1 users [..] Memory failure: 0xaf34214: recovery action for reserved kernel page: Failed mce: Memory error not recovered <reboot> ...and with these changes: Injecting memory failure for pfn 0x20cb00 at process virtual address 0x7f763dd00000 Memory failure: 0x20cb00: Killing dax-pmd:5421 due to hardware memory corruption Memory failure: 0x20cb00: recovery action for dax page: Recovered Given all the cross dependencies I propose taking this through nvdimm.git with acks from Naoya, x86/core, x86/RAS, and of course dax folks" * tag 'libnvdimm-for-4.19_dax-memory-failure' of gitolite.kernel.org:pub/scm/linux/kernel/git/nvdimm/nvdimm: libnvdimm, pmem: Restore page attributes when clearing errors x86/memory_failure: Introduce {set, clear}_mce_nospec() x86/mm/pat: Prepare {reserve, free}_memtype() for "decoy" addresses mm, memory_failure: Teach memory_failure() about dev_pagemap pages filesystem-dax: Introduce dax_lock_mapping_entry() mm, memory_failure: Collect mapping size in collect_procs() mm, madvise_inject_error: Let memory_failure() optionally take a page reference mm, dev_pagemap: Do not clear ->mapping on final put mm, madvise_inject_error: Disable MADV_SOFT_OFFLINE for ZONE_DEVICE pages filesystem-dax: Set page->index device-dax: Set page->index device-dax: Enable page_mapping() device-dax: Convert to vmf_insert_mixed and vm_fault_t
-
Linus Torvalds authored
Pull libnvdimm updates from Dave Jiang: "Collection of misc libnvdimm patches for 4.19 submission: - Adding support to read locked nvdimm capacity. - Change test code to make DSM failure code injection an override. - Add support for calculate maximum contiguous area for namespace. - Add support for queueing a short ARS when there is on going ARS for nvdimm. - Allow NULL to be passed in to ->direct_access() for kaddr and pfn params. - Improve smart injection support for nvdimm emulation testing. - Fix test code that supports for emulating controller temperature. - Fix hang on error before devm_memremap_pages() - Fix a bug that causes user memory corruption when data returned to user for ars_status. - Maintainer updates for Ross Zwisler emails and adding Jan Kara to fsdax" * tag 'libnvdimm-for-4.19_misc' of gitolite.kernel.org:pub/scm/linux/kernel/git/nvdimm/nvdimm: libnvdimm: fix ars_status output length calculation device-dax: avoid hang on error before devm_memremap_pages() tools/testing/nvdimm: improve emulation of smart injection filesystem-dax: Do not request kaddr and pfn when not required md/dm-writecache: Don't request pointer dummy_addr when not required dax/super: Do not request a pointer kaddr when not required tools/testing/nvdimm: kaddr and pfn can be NULL to ->direct_access() s390, dcssblk: kaddr and pfn can be NULL to ->direct_access() libnvdimm, pmem: kaddr and pfn can be NULL to ->direct_access() acpi/nfit: queue issuing of ars when an uc error notification comes in libnvdimm: Export max available extent libnvdimm: Use max contiguous area for namespace size MAINTAINERS: Add Jan Kara for filesystem DAX MAINTAINERS: update Ross Zwisler's email address tools/testing/nvdimm: Fix support for emulating controller temperature tools/testing/nvdimm: Make DSM failure code injection an override acpi, nfit: Prefer _DSM over _LSR for namespace label reads libnvdimm: Introduce locked DIMM capacity support
-
Colin Ian King authored
Trivial fix to spelling mistake in DP_ERR error message Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-