Implement Tx status reporting using skb_complete_wifi_ack().
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Interrupt moderation parameters will never be passed as module
parameters. For product, they will be hard-coded after lab testing,
and for debugging, they can be altered via debugfs.
Signed-off-by: Vladimir Shulman <qca_shulmanv@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Due to HW limitation, inter-packet gap timeout max value is 13 usec.
Update of current thresholds from 15 to 13 usec.
Signed-off-by: Vladimir Shulman <qca_shulmanv@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Tuning rings size for performance optimization.
Increasing Tx ring size, allows buffering more packets for HW, thus
eliminating idle periods which were observed with smaller ring at
high throughput, because HW was fetching packets faster than driver was
filling them into the TX ring. Rx ring was similarly increased to
avoid same problems in Rx.
Signed-off-by: Vladimir Shulman <qca_shulmanv@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Tx queue was hard-coded to 1000 in ether_setup. Add wil_dev_setup
function which configures tx queue len to chosen default value
after calling ether_setup.
Signed-off-by: Vladimir Shulman <qca_shulmanv@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

upon cfg80211_stop_ap, a graceful AP shutdown is requested from firmware
followed by firmware reset.
In case graceful request failed, error was returned to cfg80211.

The change is to return success in this scenario, because firmware
reset will anyhow shutdown the AP.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

netif_carrier_on indication was too late. In case Rx packet received
before netif_carrier_on indication, upper layers could not send
Tx packet back.

The fix is to indicate netif_carrier_on earlier:
for STA, indicate netif_carrier_on when association starts.
for AP/PCP, indicate netif_carrier_on upon starting AP/PCP.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Incorporate changes from firmware.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

After rtl8192cu download firmware routine, set fw_ready flag.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Some devices do not support extended scan.
This patch adds support to enble ext_scan selectively.
For SD/PCIe interfaces, deefine ext_scan_support as part of
card structure and use it to initialize ext_scan in adapter
during registering device. For USB interfaces, we initialize
ext_scan during register_dev handler.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

USB8801 is Marvell's 1x1 802.11bgn offering.
Patch adds Device IDs support and defines TX buffer size.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Frank Huang <frankh@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

SD8801 is Marvell's 1x1 802.11bgn offering.
This patch adds Device IDs for SD8801 and also defines card
structure which has definition for register offsets, buffer sizes etc.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Frank Huang <frankh@marvell.com>
Reviewed-by: James Cameron <quozl@laptop.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ath9k and ath9k_htc use the variable name "led_blink" to indicate
whether the module parameter "blink" is on. This name is easy to
conflict with other variables, and has caused a compiler error found
by kbuild test bot. The compiler error is as following:

drivers/net/wireless/ath/ath9k/ath9k_htc.o:(.data+0x47c): multiple definition of `led_blink'
drivers/net/wireless/ath/ath9k/ath9k.o:(.bss+0x20): first defined here

Fixes: 3a939a67 ("ath9k_htc: Add a module parameter to disable blink")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Hong Xu <hong@topbug.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Patch "rtlwifi: add support to send beacon frame" allows
the beaconing of rtl8192cu. But mesh beaconing is not
working. Fix this.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

In AP mode, beacon frame is necessary to keep connection.
this patch adds a sending beacon frame routine in initialization routine.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch adds fix to set carrier state off during ndo_open.
Carrier should be set to ON when device is ready to send data.
In case of station/adhoc interface device is able to transfer
data after successful association/join operation.
For AP this would be after bss_active event.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Starting with kernel 3.19-rc1 early registration of bcma on MIPS is done
a bit later, with memory allocator available. This allows us to simplify
code by using standard bus scanning method.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The kernel's string library does in fact have strcasecmp, at least
since ded220bd ("[STRING]: Move strcasecmp/strncasecmp to
lib/string.c"). Moreover, this open-coded version is in fact wrong: If
the strings only differ in their last character, a and b have already
been incremented to point to the terminating NUL bytes, so they would
wrongly be treated as equal.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

if(!wait_for_completion_interruptible_timeout(...))
only handles the timeout case - this patch adds handling the
signal case the same as timeout.
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

if(!wait_for_completion_interruptible_timeout(...))
only handles the timeout case - this patch adds handling the
signal case the same as timeout.
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Coverity: CID 114932
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This clause is conditioned on htc_hdr != NULL, but it will only be NULL
when that check is reached.

Coverity: CID 114318
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch introduces the use of function put_unaligned_le32.

This is done using Coccinelle and semantic patch used is as follows:

@A@
typedef u32, __le32, uint32_t;
{u32,__le32,uint32_t} e32;
identifier tmp;
expression ptr;
expression y,e;
type T;
type T;
@@

- tmp = cpu_to_le32(y);

<+... when != tmp
(
- memcpy(ptr, (T)&tmp, \(4\|sizeof(u32)\|sizeof(__le32)\|sizeof(uint32_t)\|sizeof(e32)\));
+ put_unaligned_le32(y,ptr);
|
- memcpy(ptr, (T)&tmp, ...);
+ put_unaligned_le32(y,ptr);
)
...+>
? tmp = e

@@ type T; identifier a.tmp; @@

- T tmp;
...when != tmp
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This moves main bus init code to the main.c and renames old function to
make its purpose clear.
Thanks to this change we'll also be able to separate scanning from
registration (and support PCIe Gen 2 devices) in the future.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Call b43_leds_stop during suspend to avoid this WARN:

WARNING: CPU: 1 PID: 0 at net/mac80211/util.c:755 ieee80211_can_queue_work.isra.11+0x35/0x50 [mac80211]()
queueing ieee80211 work while going to suspend

 [...]

Call Trace:
 [<c165fb2a>] dump_stack+0x48/0x69
 [<c1052f7b>] warn_slowpath_common+0x8b/0xc0
 [<f9c30225>] ? ieee80211_can_queue_work.isra.11+0x35/0x50 [mac80211]
 [<f9c30225>] ? ieee80211_can_queue_work.isra.11+0x35/0x50 [mac80211]
 [<c1052fe3>] warn_slowpath_fmt+0x33/0x40
 [<f9c30225>] ieee80211_can_queue_work.isra.11+0x35/0x50 [mac80211]
 [<f9c30260>] ieee80211_queue_work+0x20/0x40 [mac80211]
 [<f9f25d78>] b43_led_brightness_set+0x28/0x30 [b43]
 [<c14f3835>] led_timer_function+0xd5/0xe0
 [<c10cb534>] call_timer_fn+0xa4/0x4a0
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

We recently introduced a new error path which needs an unlock.

Fixes: 6d5a748d ('wlcore: add ability to reduce FW interrupts during suspend')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The else if check condition checks for the opposite of the
if check, hence the else if check is redundant and can be
replaced with a simple else:

if (rtlpriv->rtlhal.macphymode == SINGLEMAC_SINGLEPHY) {
	..
} else if (rtlpriv->rtlhal.macphymode != SINGLEMAC_SINGLEPHY) {
	..
}

replaced with:

if (rtlpriv->rtlhal.macphymode == SINGLEMAC_SINGLEPHY) {
	..
} else {
	..
}
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Add an option "blink" to enable or disable the LED blink. The default
value is set to 1 so that existing users would not experience any
unexpected changes.
Signed-off-by: Hong Xu <hong@topbug.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Currently, wcn36xx only asks for a TX BA session if it has
already established one for RX.  Thus, two wcn36xx devices cannot
do a-mpdu between themselves since they both wait for the other
to go first.  Fix this by starting a BA session after a few QoS
data frames have been sent to a STA.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The pdu is part of the buffer descriptor, so it makes
sense that one function would fill both.  Also, passing
the whole skb instead of just the header pointer to the
set_tx_data function paves the way for using its fields
for ampdu setup inside set_tx_data().
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The dxe lock is missing its initialization, so add it.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ctl->skb_lock is never initialized, a fact caught by lockdep.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The DMA engine will reset the valid bit after a descriptor is
complete; any with the valid bit still set may still be in
use by the hardware, so check that before freeing the descriptor.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

wcn36xx currently sends an incorrect sequence number into the BA session
setup firmware command: it should be saving or updating the ssn in the
TX_START ampdu_action callback instead of waiting until TX_OPERATIONAL.
However, we can sidestep the issue by letting the hardware generate the
sequence numbers for QoS frames, as is done in prima, so do that.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

bd->tx_comp is a single bit in a bitfield, so assigning
"info->flags & IEEE80211_TX_CTL_REQ_TX_STATUS" only happens
to work because TX_STATUS is defined to BIT(0); if it were
any other bit this assignment would fail.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Set up default configuration for the device when we call start.
The defaults come from dumps from the prima driver for the same
hardware.

This fixes transmit A-MPDU; previously only one MPDU would be
sent per A-MPDU due to missing MAX_MPDUS_IN_AMPDU setting.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Signed-off-by: Giel van Schijndel <me@mortis.eu>
Reported-at: http://www.viva64.com/en/b/0299/Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Avoid printing dev_{warn/dbg} messages while holding spinlock.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Ignore scan and connection requests from cfg80211 when driver
unload is in process or previous command has timed out due to
a firmware bug. This patch fixes corner case system crash
issues.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Check if the frame has been completed without any
error and use IEEE80211_TX_STAT_NOACK_TRANSMITTED to
indicate successful transmission of no-ack frames.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>