We are going to reuse some of this functionality to implement retimer
NVM upgrade so move common NVM functionality into its own file. We also
rename the structure from tb_switch_nvm to tb_nvm to make it clear that
it is not just for switches.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

With USB4 Intel is also using its USB-IF ID (0x8087) with the new
devices. The NVM format is the same. Add this to the driver so NVM
upgrade is possible with these devices as well.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

We can test some parts of tunneling, like path allocation without access
to test hardware so add KUnit tests for PCIe, DP and USB3 tunneling.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

USB3 supports both isochronous and non-isochronous traffic. The former
requires guaranteed bandwidth and can take up to 90% of the total
bandwidth. With USB4 USB3 is tunneled over USB4 fabric which means that
we need to make sure there is enough bandwidth allocated for the USB3
tunnels in addition to DisplayPort tunnels.

Whereas DisplayPort bandwidth management is static and done before the
DP tunnel is established, the USB3 bandwidth management is dynamic and
allows increasing and decreasing the allocated bandwidth according to
what is currently consumed. This is done through host router USB3
downstream adapter registers.

This adds USB3 bandwidth management to the software connection manager
so that we always try to allocate maximum bandwidth for DP tunnels and
what is left is allocated for USB3.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

We need to call this from tb.c when we improve the bandwidth management
to take USB3 into account.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

Each host router USB3 downstream adapter has a set of registers that are
used to negotiate bandwidth between the connection manager and the
internal xHCI controller. These registers allow dynamic bandwidth
management for USB3 isochronous traffic based on what is actually
consumed vs. allocated at any given time.

Implement these USB3 bandwidth negotiation routines to allow the
software connection manager take advantage of these.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

Sometimes it takes longer for DPRX to be set so increase the timeout to
cope with this.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

Whereas DisplayPort bandwidth is consumed only in one direction (from DP
IN adapter to DP OUT adapter), USB3 adds separate bandwidth for both
upstream and downstream directions.

For this reason extend the tunnel consumed bandwidth routines to support
both directions and implement this for DP.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

Just for symmetry with the usb4_switch_map_usb3_down() make this one
also return ports that are enabled.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

We need to call this on enabled ports in order to find the mapping from
host router USB4 port to a USB 3.x downstream adapter, so make the
function return enabled ports as well.

While there fix parameter alignment in tb_find_usb3_down().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

USB3 tunneling is possible only over USB4 link so don't create USB3
tunnels if that's not the case.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

USB4 spec allows DP tunneling from any router that has DP IN adapter,
not just from host router. The driver currently only added the DP IN
resources for the host router because Thunderbolt 1, 2 and 3 devices do
not have DP IN adapters. However, USB4 allows device routers to have DP
IN adapter as well so update the driver to add DP IN resources for each
device that has one. One example would be an eGPU enclosure where the
eGPU output is forwarded to DP IN port and then tunneled over the USB4
fabric.

Only limitation we add now is that the DP IN and DP OUT that gets paired
for tunnel creation should both be under the same topology starting from
host router downstream port. In other words we do not create DP tunnels
across host router at this time even though that is possible as well but
it complicates the bandwidth management and there is no real use-case
for this anyway.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

This adds KUnit tests for path walking which is only dependent on
software structures, so no hardware is needed to run these.

We make these available only when both KUnit and the driver itself are
built into the kernel image. The reason for this is that KUnit adds its
own module_init() call in kunit_test_suite() which generates linker
error because the driver does the same in nhi.c. This should be fine for
now because these tests are only meant to run by developers anyway.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

Currently we have only supported paths that follow daisy-chain topology
but USB4 also allows to build trees of devices. For this reason increase
maximum path length we use for discovery to be from the lowest level to
the host router and back to the same level.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

If the path is not complete when we do discovery the number of hops may
be less than with the full path. As an example when this can happen is
that user unloads the driver, disconnects the topology, and loads the
driver back. If there is PCIe or USB3 tunnel involved this may happen.

Take this into account in tb_pcie_init_path() and tb_usb3_init_path()
and prevent potential access over array limits.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

Add sanity check that given src and dst ports are reachable through path
walk before allocating a path. If they are not then bail out early.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

With USB4, topologies are not limited to daisy-chains anymore so when
calculating how many hops are between two ports we need to walk the
whole path instead.

Add helper function tb_for_each_port_on_path() that can be used to walk
over each port on a path and make tb_path_alloc() to use it.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

USB4 makes it possible to have tree topology of devices connected in the
same way than USB3. This was actually possible in Thunderbolt 1, 2 and 3
as well but all the available devices only had two ports which allows
building only daisy-chains of devices.

With USB4 it is possible for example that there is DP IN adapter as part
of eGPU device router and that should be tunneled over the tree topology
to a DP OUT adapter. This updates the tb_next_port_on_path() to support
such topologies.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

The USB3 discovery used wrong indices when tunnel is discovered. It
should use TB_USB3_PATH_DOWN for path that flows downstream and
TB_USB3_PATH_UP when it flows upstream. This should not affect the
functionality but better to fix it.

Fixes: e6f81858 ("thunderbolt: Add support for USB 3.x tunnels")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@vger.kernel.org # v5.6+

The end-to-end (E2E) workaround is needed for Falcon Ridge (TBT 2)
controller when E2E is enabled for both ends of the host-to-host
connection. However, we never supported full E2E in the first place so
this code is not necessary at the moment. Further this allows us to use
all available rings for data except ring 0 which is reserved for the
control path.

The complete E2E flow control is explained in the USB4 spec so we may
add it back later if needed but at least the networking driver seems to
work fine without, and the higher level stack, like TCP will retransmit
lost packets anyway.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

NHI (The host interface adapter) is allowed to use HopIDs 1-7 as well so
relax the restriction in tb_port_alloc_hopid() to support this.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

While Intel hardware typically has hop_count (Total Paths in the spec)
12 the USB4 spec allows this to be anything between 1 and 21 so no need
to warn about this. Simply log number of paths at debug level.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

On a systems where the Thunderbolt controller is present all the time
the kernel nodename may not yet set by the userspace when the driver is
loaded. This means when another host is connected it may see the default
"(none)" hostname instead of the system real hostname.

For this reason build the initial XDomain property block only upon first
connect. This should make sure the userspace has had chance to set it up.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

Fix the spelling of "specification", and add a missing "the" article.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>

Pull SafeSetID update from Micah Morton:
 "Add additional LSM hooks for SafeSetID

  SafeSetID is capable of making allow/deny decisions for set*uid calls
  on a system, and we want to add similar functionality for set*gid
  calls.

  The work to do that is not yet complete, so probably won't make it in
  for v5.8, but we are looking to get this simple patch in for v5.8
  since we have it ready.

  We are planning on the rest of the work for extending the SafeSetID
  LSM being merged during the v5.9 merge window"

* tag 'LSM-add-setgid-hook-5.8-author-fix' of git://github.com/micah-morton/linux:
  security: Add LSM hooks to set*gid syscalls

The SafeSetID LSM uses the security_task_fix_setuid hook to filter
set*uid() syscalls according to its configured security policy. In
preparation for adding analagous support in the LSM for set*gid()
syscalls, we add the requisite hook here. Tested by putting print
statements in the security_task_fix_setgid hook and seeing them get hit
during kernel boot.
Signed-off-by: Thomas Cedeno <thomascedeno@google.com>
Signed-off-by: Micah Morton <mortonm@chromium.org>

Pull btrfs updates from David Sterba:
 "This reverts the direct io port to iomap infrastructure of btrfs
  merged in the first pull request. We found problems in invalidate page
  that don't seem to be fixable as regressions or without changing iomap
  code that would not affect other filesystems.

  There are four reverts in total, but three of them are followup
  cleanups needed to revert a43a67a2 cleanly. The result is the
  buffer head based implementation of direct io.

  Reverts are not great, but under current circumstances I don't see
  better options"

* tag 'for-5.8-part2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  Revert "btrfs: switch to iomap_dio_rw() for dio"
  Revert "fs: remove dio_end_io()"
  Revert "btrfs: remove BTRFS_INODE_READDIO_NEED_LOCK"
  Revert "btrfs: split btrfs_direct_IO to read and write part"

Pull networking fixes from David Miller:

 1) Fix cfg80211 deadlock, from Johannes Berg.

 2) RXRPC fails to send norigications, from David Howells.

 3) MPTCP RM_ADDR parsing has an off by one pointer error, fix from
    Geliang Tang.

 4) Fix crash when using MSG_PEEK with sockmap, from Anny Hu.

 5) The ucc_geth driver needs __netdev_watchdog_up exported, from
    Valentin Longchamp.

 6) Fix hashtable memory leak in dccp, from Wang Hai.

 7) Fix how nexthops are marked as FDB nexthops, from David Ahern.

 8) Fix mptcp races between shutdown and recvmsg, from Paolo Abeni.

 9) Fix crashes in tipc_disc_rcv(), from Tuong Lien.

10) Fix link speed reporting in iavf driver, from Brett Creeley.

11) When a channel is used for XSK and then reused again later for XSK,
    we forget to clear out the relevant data structures in mlx5 which
    causes all kinds of problems. Fix from Maxim Mikityanskiy.

12) Fix memory leak in genetlink, from Cong Wang.

13) Disallow sockmap attachments to UDP sockets, it simply won't work.
    From Lorenz Bauer.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (83 commits)
  net: ethernet: ti: ale: fix allmulti for nu type ale
  net: ethernet: ti: am65-cpsw-nuss: fix ale parameters init
  net: atm: Remove the error message according to the atomic context
  bpf: Undo internal BPF_PROBE_MEM in BPF insns dump
  libbpf: Support pre-initializing .bss global variables
  tools/bpftool: Fix skeleton codegen
  bpf: Fix memlock accounting for sock_hash
  bpf: sockmap: Don't attach programs to UDP sockets
  bpf: tcp: Recv() should return 0 when the peer socket is closed
  ibmvnic: Flush existing work items before device removal
  genetlink: clean up family attributes allocations
  net: ipa: header pad field only valid for AP->modem endpoint
  net: ipa: program upper nibbles of sequencer type
  net: ipa: fix modem LAN RX endpoint id
  net: ipa: program metadata mask differently
  ionic: add pcie_print_link_status
  rxrpc: Fix race between incoming ACK parser and retransmitter
  net/mlx5: E-Switch, Fix some error pointer dereferences
  net/mlx5: Don't fail driver on failure to create debugfs
  net/mlx5e: CT: Fix ipv6 nat header rewrite actions
  ...

This reverts commit a43a67a2.

This patch reverts the main part of switching direct io implementation
to iomap infrastructure. There's a problem in invalidate page that
couldn't be solved as regression in this development cycle.

The problem occurs when buffered and direct io are mixed, and the ranges
overlap. Although this is not recommended, filesystems implement
measures or fallbacks to make it somehow work. In this case, fallback to
buffered IO would be an option for btrfs (this already happens when
direct io is done on compressed data), but the change would be needed in
the iomap code, bringing new semantics to other filesystems.

Another problem arises when again the buffered and direct ios are mixed,
invalidation fails, then -EIO is set on the mapping and fsync will fail,
though there's no real error.

There have been discussions how to fix that, but revert seems to be the
least intrusive option.

Link: https://lore.kernel.org/linux-btrfs/20200528192103.xm45qoxqmkw7i5yl@fiona/Signed-off-by: David Sterba <dsterba@suse.com>

On AM65xx MCU CPSW2G NUSS and 66AK2E/L NUSS allmulti setting does not allow
unregistered mcast packets to pass.

This happens, because ALE VLAN entries on these SoCs do not contain port
masks for reg/unreg mcast packets, but instead store indexes of
ALE_VLAN_MASK_MUXx_REG registers which intended for store port masks for
reg/unreg mcast packets.
This path was missed by commit 9d1f6447 ("net: ethernet: ti: ale: fix
seeing unreg mcast packets with promisc and allmulti disabled").

Hence, fix it by taking into account ALE type in cpsw_ale_set_allmulti().

Fixes: 9d1f6447 ("net: ethernet: ti: ale: fix seeing unreg mcast packets with promisc and allmulti disabled")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ALE parameters structure is created on stack, so it has to be reset
before passing to cpsw_ale_create() to avoid garbage values.

Fixes: 93a76530 ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexei Starovoitov says:

====================
pull-request: bpf 2020-06-12

The following pull-request contains BPF updates for your *net* tree.

We've added 26 non-merge commits during the last 10 day(s) which contain
a total of 27 files changed, 348 insertions(+), 93 deletions(-).

The main changes are:

1) sock_hash accounting fix, from Andrey.

2) libbpf fix and probe_mem sanitizing, from Andrii.

3) sock_hash fixes, from Jakub.

4) devmap_val fix, from Jesper.

5) load_bytes_relative fix, from YiFei.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Looking into the context (atomic!) and the error message should be dropped.
Signed-off-by: Liao Pingfang <liao.pingfang@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull more cifs updates from Steve French:
 "12 cifs/smb3 fixes, 2 for stable.

   - add support for idsfromsid on create and chgrp/chown allowing
     ability to save owner information more naturally for some workloads

   - improve query info (getattr) when SMB3.1.1 posix extensions are
     negotiated by using new query info level"

* tag '5.8-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
  smb3: Add debug message for new file creation with idsfromsid mount option
  cifs: fix chown and chgrp when idsfromsid mount option enabled
  smb3: allow uid and gid owners to be set on create with idsfromsid mount option
  smb311: Add tracepoints for new compound posix query info
  smb311: add support for using info level for posix extensions query
  smb311: Add support for lookup with posix extensions query info
  smb311: Add support for SMB311 query info (non-compounded)
  SMB311: Add support for query info using posix extensions (level 100)
  smb3: add indatalen that can be a non-zero value to calculation of credit charge in smb2 ioctl
  smb3: fix typo in mount options displayed in /proc/mounts
  cifs: Add get_security_type_str function to return sec type.
  smb3: extend fscache mount volume coherency check

Let's keep "git status" happy and quiet.

Fixes: 9762dc14 ("samples: add binderfs sample program
Fixes: fca5e949 ("samples: binderfs: really compile this sample and fix build issues")
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

I'm not convinced the script makes useful automaed help lines anyway,
but since we're trying to deprecate the use of "---help---" in Kconfig
files, let's fix the doc example code too.

See commit a7f7f624 ("treewide: replace '---help---' in Kconfig
files with 'help'")

Cc: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull more Kbuild updates from Masahiro Yamada:

 - fix build rules in binderfs sample

 - fix build errors when Kbuild recurses to the top Makefile

 - covert '---help---' in Kconfig to 'help'

* tag 'kbuild-v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  treewide: replace '---help---' in Kconfig files with 'help'
  kbuild: fix broken builds because of GZIP,BZIP2,LZOP variables
  samples: binderfs: really compile this sample and fix build issues

Pull more SCSI updates from James Bottomley:
 "This is the set of changes collected since just before the merge
  window opened. It's mostly minor fixes in drivers.

  The one non-driver set is the three optical disk (sr) changes where
  two are error path fixes and one is a helper conversion.

  The big driver change is the hpsa compat_alloc_userspace rework by Al
  so he can kill the remaining user. This has been tested and acked by
  the maintainer"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (21 commits)
  scsi: acornscsi: Fix an error handling path in acornscsi_probe()
  scsi: storvsc: Remove memset before memory freeing in storvsc_suspend()
  scsi: cxlflash: Remove an unnecessary NULL check
  scsi: ibmvscsi: Don't send host info in adapter info MAD after LPM
  scsi: sr: Fix sr_probe() missing deallocate of device minor
  scsi: sr: Fix sr_probe() missing mutex_destroy
  scsi: st: Convert convert get_user_pages() --> pin_user_pages()
  scsi: target: Rename target_setup_cmd_from_cdb() to target_cmd_parse_cdb()
  scsi: target: Fix NULL pointer dereference
  scsi: target: Initialize LUN in transport_init_se_cmd()
  scsi: target: Factor out a new helper, target_cmd_init_cdb()
  scsi: hpsa: hpsa_ioctl(): Tidy up a bit
  scsi: hpsa: Get rid of compat_alloc_user_space()
  scsi: hpsa: Don't bother with vmalloc for BIG_IOCTL_Command_struct
  scsi: hpsa: Lift {BIG_,}IOCTL_Command_struct copy{in,out} into hpsa_ioctl()
  scsi: ufs: Remove redundant urgent_bkop_lvl initialization
  scsi: ufs: Don't update urgent bkops level when toggling auto bkops
  scsi: qedf: Remove redundant initialization of variable rc
  scsi: mpt3sas: Fix memset() in non-RDPQ mode
  scsi: iscsi: Fix reference count leak in iscsi_boot_create_kobj
  ...

Pull i2c updates from Wolfram Sang:
 "I2C has quite some patches for you this time. I hope it is the move to
  per-driver-maintainers which is now showing results. We will see.

  The big news is two new drivers (Nuvoton NPCM and Qualcomm CCI),
  larger refactoring of the Designware, Tegra, and PXA drivers, the
  Cadence driver supports being a slave now, and there is support to
  instanciate SPD eeproms for well-known cases (which will be
  user-visible because the i801 driver supports it), and some
  devm_platform_ioremap_resource() conversions which blow up the
  diffstat.

  Note that I applied the Nuvoton driver quite late, so some minor fixup
  patches arrived during the merge window. I chose to apply them right
  away because they were trivial"

* 'i2c/for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (109 commits)
  i2c: Drop stray comma in MODULE_AUTHOR statements
  i2c: npcm7xx: npcm_i2caddr[] can be static
  MAINTAINERS: npcm7xx: Add maintainer for Nuvoton NPCM BMC
  i2c: npcm7xx: Fix a couple of error codes in probe
  i2c: icy: Fix build with CONFIG_AMIGA_PCMCIA=n
  i2c: npcm7xx: Remove unnecessary parentheses
  i2c: npcm7xx: Add support for slave mode for Nuvoton
  i2c: npcm7xx: Add Nuvoton NPCM I2C controller driver
  dt-bindings: i2c: npcm7xx: add NPCM I2C controller
  i2c: pxa: don't error out if there's no pinctrl
  i2c: add 'single-master' property to generic bindings
  i2c: designware: Add Baikal-T1 System I2C support
  i2c: designware: Move reg-space remapping into a dedicated function
  i2c: designware: Retrieve quirk flags as early as possible
  i2c: designware: Convert driver to using regmap API
  i2c: designware: Discard Cherry Trail model flag
  i2c: designware: Add Baytrail sem config DW I2C platform dependency
  i2c: designware: slave: Set DW I2C core module dependency
  i2c: designware: Use `-y` to build multi-object modules
  dt-bindings: i2c: dw: Add Baikal-T1 SoC I2C controller
  ...