- 21 Oct, 2019 7 commits
-
-
Chris Wilson authored
Currently even though i915_vma_parked() operates on a per-gt struct, it is called from a global pm notify. This oddity was only because the long term plan is to decouple the vma cache from the pm notification, but right now the oddity stands out like a sore thumb! Suggested-by:
Tvrtko Ursulin <tvrtko.ursulin@intel.com> Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk> Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com> Reviewed-by:
-
Chris Wilson authored
To flush idle barriers, and even inflight requests, we want to send a preemptive 'pulse' along an engine. We use a no-op request along the pinned kernel_context at high priority so that it should run or else kick off the stuck requests. We can use this to ensure idle barriers are immediately flushed, as part of a context cancellation mechanism, or as part of a heartbeat mechanism to detect and reset a stuck GPU. Signed-off-by:
-
Chris Wilson authored
i915_active must track over any engine, so expand the selftest to iterate over all uabi engines. Signed-off-by:
-
Ville Syrjälä authored
On ILK+ the documented min hdisplay is 64, min hblank is 32, and min vblank is 5. On earlier platforms min hblank is also 32, and min vblank is 3. Make sure the mode satisfies those limits. There are further limits for HDMI and pfit use cases, but we'll check for those in a more specific location. Signed-off-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190718144340.1114-2-ville.syrjala@linux.intel.comReviewed-by:
Manasi Navare <manasi.d.navare@intel.com>
-
Chris Wilson authored
If we change the priority of the active context, then it has no impact on the decision of whether to preempt the active context -- we don't preempt the context with itself. In this situation, we elide the tasklet rescheduling and should *not* be marking up the queue_priority_hint as that may mask a later submission where we decide we don't have to kick the tasklet as a higher priority submission is pending (spoiler alert, it was not). Signed-off-by:
Mika Kuoppala <mika.kuoppala@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191021080226.537-1-chris@chris-wilson.co.uk
-
Joonas Lahtinen authored
Signed-off-by:Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
-
Chris Wilson authored
Use the local vgpu_lock while preparing workloads to avoid taking the obsolete i915->drm.struct_mutex Signed-off-by:
Zhenyu Wang <zhenyuw@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191016183902.13614-1-chris@chris-wilson.co.uk
-
- 20 Oct, 2019 2 commits
-
-
Andi Shyti authored
Although the ring management is much smaller compared to the other GT power management functions, continue the theme of extracting it out of the huge intel_pm.c for maintenance. Based on a patch by Chris Wilson. Signed-off-by:
Andi Shyti <andi.shyti@intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by:
-
Lionel Landwerlin authored
The current logic just reapplies the same configuration already stored into stream->oa_config instead of the newly selected one. Signed-off-by:
Lionel Landwerlin <lionel.g.landwerlin@intel.com> Fixes: 7831e9a9 ("drm/i915/perf: Allow dynamic reconfiguration of the OA stream") Cc: Chris Wilson <chris@chris-wilson.co.uk> Reviewed-by:
-
- 19 Oct, 2019 5 commits
-
-
Lucas De Marchi authored
s/?/:/ so it gets correctly colored by dmesg. Signed-off-by:
Lucas De Marchi <lucas.demarchi@intel.com> Reviewed-by:
-
Lucas De Marchi authored
This way it's easier to figure out what didn't match when we have multiple pipes enabled. v2: pass drm_crtc and use the more common [CRTC:%d:%s] format (Ville) v3: use struct intel_crtc type to pass crtc around (Ville) Signed-off-by: -
Lucas De Marchi authored
The new line is already added by pipe_config_mismatch(), so the callers shouldn't add it. Signed-off-by:
-
Lucas De Marchi authored
Both Ice Lake and Elkhart Lake (gen 11) support MST on all external connections except DDI A. Tiger Lake (gen 12) supports on all external connections. Move the check to happen inside intel_dp_mst_encoder_init() and add specific platform checks. v2: Replace != with == checks for ports on gen < 11 (Ville) Signed-off-by:
-
Lucas De Marchi authored
Instead of the ever growing switch, just compute the ddi io power domain based on the port number. Signed-off-by:
José Roberto de Souza <jose.souza@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191011010907.103309-2-lucas.demarchi@intel.com
-
- 18 Oct, 2019 26 commits
-
-
Manasi Navare authored
In the transcoder port sync mode, the slave transcoders mask their vblanks until master transcoder's vblank so while disabling them, make sure slaves are disabled first and then the masters. v5: * Dont pass dev priv to get_slave_crtc (Ville) v4: * Obtain slave state from master (Maarten) v3: * Rebase v2: * Use the intel_old_crtc_state_disables() helper Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Matt Roper <matthew.d.roper@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Signed-off-by:
Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20191018172725.1338-6-manasi.d.navare@intel.com
-
Manasi Navare authored
This clears the transcoder port sync bits of the TRANS_DDI_FUNC_CTL2 register during crtc_disable(). v3: * Rebase on maarten's patches v2: * Directly write the trans_port_sync reg value (Maarten) Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Matt Roper <matthew.d.roper@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Signed-off-by:
-
Manasi Navare authored
As per the display enable sequence, we need to follow the enable sequence for slaves first with DP_TP_CTL set to Idle and configure the transcoder port sync register to select the corersponding master, then follow the enable sequence for master leaving DP_TP_CTL to idle. At this point the transcoder port sync mode is configured and enabled and the Vblanks of both ports are synchronized so then set DP_TP_CTL for the slave and master to Normal and do post crtc enable updates. v11: * Rebase (Manasi) v10: * in trans sync mode, dont stop link train for tgl (Manasi) v9: Remove update_scanline_offset to rebase on Maarten's patch (Manasi) v8: * Rebase on Maarten's patches (Manasi) v7: * Use ffs(slaves) to get slave crtc (Ville) v6: * Modeset implies active_changed, remove one condition (Maarten) v5: * Fix checkpatch warning (Manasi) v4: * Reuse skl_commit_modeset_enables() hook (Maarten) * Obtain slave crtc and states from master (Maarten) v3: * Rebase on drm-tip (Manasi) v2: * Create a icl_update_crtcs hook (Maarten, Danvet) * This sequence only for CRTCs in trans port sync mode (Maarten) Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Matt Roper <matthew.d.roper@intel.com> Signed-off-by:
-
Manasi Navare authored
After the state is committed, we readout the HW registers and compare the HW state with the SW state that we just committed. For Transcdoer port sync, we add master_transcoder and the salves bitmask to the crtc_state, hence we need to read those during the HW state readout to avoid pipe state mismatch. v11: * Move master trans init to get pipe_Config hooks (Ville) v10: * Initialize master_tarnscoder readout for all platforms (Ville) v9: * Initialize master_transcoder = INVALID at get config (Ville) v8: * Use master_select -1, address TRANS_EDP case (Ville) * Rename master_transcoder to _readout (Lucas) v7: * NDont read HW state for DSI v6: * Go through both parts of HW readout (Maarten) * Add a WARN if the same trans configured as master and slave (Ville, Maarten) v5: * Add return INVALID in defaut case (Maarten) v4: * Get power domains in master loop for get_config (Ville) v3: * Add TRANSCODER_D (Maarten) * v3 Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> v2: * Add Transcoder_D and MISSING_CASE (Maarten) Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Matt Roper <matthew.d.roper@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Signed-off-by:
-
Manasi Navare authored
In case of tiled displays where different tiles are displayed across different ports, we need to synchronize the transcoders involved. This patch implements the transcoder port sync feature for synchronizing one master transcoder with one or more slave transcoders. This is only enbaled in slave transcoder and the master transcoder is unaware that it is operating in this mode. This has been tested with tiled display connected to ICL. v7: * Rebase on Maarten's patches v6: * Use master_trans +1 and address missing trans_edp case (Ville) v5: * Add TRANSCODER_D case and MISSING_CASE (Maarten) v4: Rebase v3: * Check of DP_MST moved to atomic_check (Maarten) v2: * Do not use RMW, just write to the register in commit (Jani N) Cc: Daniel Vetter <daniel.vetter@intel.com> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Matt Roper <matthew.d.roper@intel.com> Cc: Jani Nikula <jani.nikula@intel.com> Signed-off-by:
-
Manasi Navare authored
In case of tiled displays when the two tiles are sent across two CRTCs over two separate DP SST connectors, we need a mechanism to synchronize the two CRTCs and their corresponding transcoders. So use the master-slave mode where there is one master corresponding to last horizontal and vertical tile that needs to be genlocked with all other slave tiles. This patch identifies saves the master transcoder in all the slave CRTC states. This is needed to select the master CRTC/transcoder while configuring transcoder port sync for the corresponding slaves. v6: Rebase (manasi) v5: * Address Ville's comments * Just pass crtc_state, no need to check GEN (Ville) v4: * Rebase v3: * Use master_tramscoder instead of master_crtc for valid HW state readouts (Ville) v2: * Move this to intel_mode_set_pipe_config(Jani N, Ville) * Use slave_bitmask to save associated slaves in master crtc state (Ville) Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Matt Roper <matthew.d.roper@intel.com> Signed-off-by:
-
Janusz Krzysztofik authored
Commit 2d6f6f35 ("drm/i915: add i915_driver_modeset_remove()") claimed removal of asymmetry in probe() and remove() calls, however, it didn't take care of calling intel_irq_uninstall() on driver remove. That doesn't hurt as long as we still call it from intel_modeset_driver_remove() but in order to have full symmetry we should call it again from i915_driver_modeset_remove(). Note that it's safe to call intel_irq_uninstall() twice thanks to commit b318b824 ("drm/i915: Nuke drm_driver irq vfuncs"). We may only want to mention the case we are adding in a related FIXME comment provided by that commit. While being at it, update the name of function mentioned as calling it out of sequence as that name has been changed meanwhile by commit 78dae1ac ("drm/i915: Propagate "_remove" function name suffix down"). Suggested-by:
Michal Wajdeczko <michal.wajdeczko@intel.com> Signed-off-by:
Janusz Krzysztofik <janusz.krzysztofik@linux.intel.com> Cc: Michal Wajdeczko <michal.wajdeczko@intel.com> Reviewed-by:
-
Vivek Kasireddy authored
JasperLake PCH (JSP) has DDI HPD pin mappings similar to TGP and not MCC. Also add the correct HPD pin mappings for the MCC PCH. Cc: Matt Roper <matthew.d.roper@intel.com> Signed-off-by:
Vivek Kasireddy <vivek.kasireddy@intel.com> Reviewed-by:
Matt Roper <matthew.d.roper@intel.com> Signed-off-by:
-
Ville Syrjälä authored
All the timeout values fit in u16, so let's shrink the structure a bit. This ends up actually increasing the .text size a bit due to some changes in instructions (constant imul+small jmps replaced with mov+bigger jmpqs). Seems pretty arbitrary to me so I'll just pretend I didn't see it. text data bss dec hex filename - 34521 360 0 34881 8841 intel_hdmi.o + 34537 360 0 34897 8851 intel_hdmi.o Signed-off-by:Ramalingam C <ramalingam.c@intel.com>
-
Ville Syrjälä authored
The only reason for the timeout2 value in the array is the HDCP_2_2_AKE_SEND_HPRIME message. But that one still needs special casing inside the loop, and so just ends up making the code harder to read. Let's just remove this leaky timeout2 abstraction and special case that one command in a way that is easy to understand. We can then remove the timeout2 member from struct entirely. text data bss dec hex filename - 34633 360 0 34993 88b1 intel_hdmi.o + 34521 360 0 34881 8841 intel_hdmi.o Signed-off-by: -
Ville Syrjälä authored
The .read_2_2() hooks is never called for any of the message types with a zero timeout. So it's all just dead weight which we can chuck. text data bss dec hex filename - 34701 360 0 35061 88f5 intel_hdmi.o + 34633 360 0 34993 88b1 intel_hdmi.o Signed-off-by: -
Ville Syrjälä authored
The array is there only for timeout, "data" doesn't mean anything so let's rename the thing to be more descriptive. Signed-off-by:
-
Ville Syrjälä authored
Make the ways/sets arrays static cosnt u8 to shrink things a bit. text data bss dec hex filename - 23935 629 128 24692 6074 i915_drv.o + 23818 629 128 24575 5fff i915_drv.o Signed-off-by: -
Ville Syrjälä authored
Despite the its name dirty_pipes refers to crtc indexes. Let's change its behaviout to match the name. Signed-off-by:
Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
-
Ville Syrjälä authored
The 'realloc_pipes' bitmask is pointless. It is either: a) the set of pipes which are already part of the state, in which case adding them again is entirely redundant b) the set of all pipes which we then add to the state Also the fact that 'realloc_pipes' uses the crtc indexes is going to bite is at some point so best get rid of it quick. Signed-off-by:
-
Ville Syrjälä authored
changed==true just means we have some crtcs in the state. All the stuff following this only operates on crtcs in the state anyway so there is no point in having this bool. Signed-off-by:
-
Ville Syrjälä authored
The DP port/pipe goes wonky if we try to use timings with hdisplay==4096 on pre-HSW platforms. The link fails to train and the pipe may not signal vblank interrupts. On HDMI such at mode works just fine (tested on ELK/SNB/CHV). So let's refuse such modes on DP on older platforms. Signed-off-by:
-
Ville Syrjälä authored
Replace the hand rolled stuff with drm_encoder_mask() when populating possible_clones, and rename the function to intel_encoder_possible_clones() to make it clear what it's used for. Signed-off-by:
Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
-
Ville Syrjälä authored
Unlike other planes the cursor currently handles 180 degree rotation adjustment during the hardware programming phase. Let's move that stuff into intel_cursor_check_surface() to match how we do things with other plane types. And while at we'll plop in the final src x/y coordinates (which will actually always be zero) into the src rect and color_plane[0].x/y, just for some extra consistency. Signed-off-by:
-
Chris Wilson authored
Use the local gt for iterating over the available set of engines. Signed-off-by:
-
Chris Wilson authored
Remember to include the newly created mock engine in the list of available engines inside the gt. Fixes: a50134b1 ("drm/i915: Make for_each_engine_masked work on intel_gt") Signed-off-by:
-
Matthew Auld authored
Convert stolen memory over to a region object. Still leaves open the question with what to do with pre-allocated objects... Signed-off-by:
Matthew Auld <matthew.auld@intel.com> Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: Abdiel Janulgue <abdiel.janulgue@linux.intel.com> Reviewed-by:
-
Matthew Auld authored
Convert shmem to an intel_memory_region. Signed-off-by:
-
Abdiel Janulgue authored
Nothing to enumerate yet... Signed-off-by:
Abdiel Janulgue <abdiel.janulgue@linux.intel.com> Signed-off-by:
-
Chris Wilson authored
Normally, we try and skip submission if ELSP[1] is filled. However, we may desire to enable timeslicing due to the queue priority, even if ELSP[1] itself does not require timeslicing. That is the queue is equal priority to ELSP[0] and higher priority then ELSP[1]. Previously, we would wait until the context switch to preempt the current ELSP[1], but with timeslicing, we want to preempt ELSP[0] and replace it with the queue. In writing the test case, it become quickly apparent that we were also suppressing the tasklet during promotion and so failing to notice when the queue started requiring timeslicing. Fixes: 2229adc8 ("drm/i915/execlist: Trim immediate timeslice expiry") Signed-off-by:
-
Tvrtko Ursulin authored
If name allocation failed the log message will contain an uninitialized error code which can be confusing. Fixes: 05488673 ("drm/i915/pmu: Support multiple GPUs") Signed-off-by:
-
