- 23 Oct, 2013 3 commits
-
-
Eliad Peller authored
Add new ap_event_mask field, to indicate events that should be unmasked only when there's an ap interface. This is done in order to avoid spurious wakeups when we don't care about the incoming event anyway. Signed-off-by:
Eliad Peller <eliad@wizery.com> Signed-off-by:
Luciano Coelho <luciano.coelho@intel.com>
-
Victor Goldenshtein authored
Print current active channel/s and a role type for that channel in the driver_state debugfs. Signed-off-by:
Victor Goldenshtein <victorg@ti.com> Signed-off-by:
-
Igal Chernobelsky authored
Driver default config is aligned with phy default parameters. Now that RDL1_3 has 2 antennas defined by default we need to explicitly define ht.mode to HT_MODE_WIDE to have SISO40 as default. Signed-off-by:
Yair Shapira <yair.shapira@ti.com> Signed-off-by:
Igal Chernobelsky <igalc@ti.com> Signed-off-by:
-
- 18 Oct, 2013 37 commits
-
-
Gabor Juhos authored
Use the module_pci_driver() macro to make the code simpler by eliminating module_init and module_exit calls. Signed-off-by:
Gabor Juhos <juhosg@openwrt.org> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Gabor Juhos authored
The PCI and SoC specific drivers are using separate code now so it is not reasonable to use the same module for both drivers anymore. Signed-off-by:
-
Gabor Juhos authored
The 'rt2800pci_hwcrypt_disabled' function is the only PCI specific callback which is used by the SoC driver. Create a clone of that to get rid of the dependency. Even though the two functions are using the same variable, but the SoC specific code will be moved into a separate module which will have its own 'modparam_nohwcrypt' variable. Signed-off-by:
-
Gabor Juhos authored
Move the function into the rt2800mmio module, in order to make it usable from other modules. Signed-off-by:
-
Gabor Juhos authored
The function is called for PCI and SoC devices however the MCU related part of the function has no effect on SoC devices. Move the common part of the function into a separate helper and use that for the SoC devices. Signed-off-by:
-
Gabor Juhos authored
The function contain code for SoC devices only. Rename the function to 'rt2800soc_disable_radio' and move it to the SoC specific section. Use the renamed function in the SoC specific code only and remove the 'if rt2x00_is_soc(rt2x00dev)' condition from the function body. Signed-off-by:
-
Gabor Juhos authored
The 'rt2800pci_set_state' function uses MCU commands to set the device state, however these have no effect on SoC devices. Use a different set_state callback which does not use the MCU fcuntions. Signed-off-by:
-
Gabor Juhos authored
Use empty firmware callbacks for SoC devices because those don't require firmware. Signed-off-by:
-
Gabor Juhos authored
Rename the 'rt2800pci_read_eeprom_soc function' to 'rt2800soc_read_eeprom' and use that directly in the SoC specific 'rt2800_ops' structure. Also move the 'rt2800pci_eeprom_read' function into an 'ifdef PCI' section and remove the 'rt2800pci_read_eeprom_soc' call from that. Additionally, remove the dummy inline eeprom functions. Those are not used anymore. Signed-off-by:
-
Gabor Juhos authored
This makes it possible to use different callback functions for PCI and SoC devices which will allow to move the SoC driver into a separate module. Signed-off-by:
-
Gabor Juhos authored
Move the functions into a separate module, in order to make those usable from other modules. Signed-off-by:
-
Gabor Juhos authored
The functions are used for devices with memory mapped I/O and contain no PCI specific code at all. Use rt2800mmio prefix instead of rt2800pci in the function names to reflect that. The patch contains no functional changes. Signed-off-by:
-
Gabor Juhos authored
Move the functions into a separate module, in order to make those usable from other modules. Also move the queue register offset macros from rt2800pci.h into rt2800mmio.h. Signed-off-by:
-
Gabor Juhos authored
The functions are used for devices with memory mapped I/O and contain no PCI specific code at all. Use rt2800mmio prefix instead of rt2800pci in the function names to reflect that. The patch contains no functional changes. Signed-off-by:
-
Gabor Juhos authored
Move the functions into a separate module, in order to make those usable from other modules. Signed-off-by:
-
Gabor Juhos authored
The functions are used for devices with memory mapped I/O and contain no PCI specific code at all. Use rt2800mmio prefix instead of rt2800pci in the function names to reflect that. The patch contains no functional changes. Signed-off-by:
-
Gabor Juhos authored
Move the functions into a separate module, in order to make those usable from other modules. Also move the RX descriptor related defines from rt2800pci.h into rt2800mmio.h Signed-off-by:
-
Gabor Juhos authored
The functions are used for devices with memory mapped I/O and contain no PCI specific code at all. Use rt2800mmio prefix instead of rt2800pci in the function names to reflect that. The patch contains no functional changes. Signed-off-by:
-
Gabor Juhos authored
Move the functions into a separate module, in order to make those usable from other modules. Also move the TX descriptor related defines from rt2800pci.h into rt2800mmio.h. Signed-off-by:
-
Gabor Juhos authored
The functions are used for devices with memory mapped I/O and contain no PCI specific code at all. Use rt2800mmio prefix instead of rt2800pci in the function names to reflect that. The patch contains no functional changes. Signed-off-by:
-
Gabor Juhos authored
Create a new module for common code which can be used for rt2800 device with memory mapped I/O. It is an empty module for now, but it will be populated by subsequent patches. Signed-off-by:
-
Felipe Pena authored
There is a typo where the checking for priv->ReAssociationRequestRetryCnt must be, it was checking for priv->AssociationRequestRetryCnt instead. Signed-off-by:
Felipe Pena <felipensp@gmail.com> Signed-off-by:
-
Arend van Spriel authored
If the SDIO host controller does not support scatter-gather the glom superframe must be transfered from the device and the data for each packet in the queue must be extracted from it. Reviewed-by:
Franky Lin <frankyl@broadcom.com> Reviewed-by:
Hante Meuleman <meuleman@broadcom.com> Reviewed-by:
Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by:
Arend van Spriel <arend@broadcom.com> Signed-off-by:
-
Arend van Spriel authored
When running on a host controller that does not support scatter-gather transfers the function brcmf_sdio_txpkt_prep() should not add tail padding buffers. Reviewed-by:
-
Arend van Spriel authored
If the host does not support scatter-gather transmit the packets in the pktq individually using brcmf_sdio_buffrw(). Reviewed-by:
-
Arend van Spriel authored
The function brcmf_sdcard_recv_chain() has been reworked with commit "brcmfmac: add sdio sg list support", but the incr_fix variable is only assigned but not used so removing it now. Reviewed-by:
-
Arend van Spriel authored
Not all calls to the function brcmf_sdio_addrprep() check the return value, but it may fail so better verify it. Reviewed-by:
-
Arend van Spriel authored
The function brcmf_sdio_sglist_rw() does a different code path when packet queue length is 1. Move this to a separate function reducing overhead in the calling context. Reviewed-by:
-
Arend van Spriel authored
The function brcmf_sdio_buffrw() is intended to be used for transfering list of packets using scatter-gather functionality. Rename function to brcmf_sdio_sglist_rw() to clarify this. Reviewed-by:
-
Arend van Spriel authored
Moving a number of assignments outside of the loop as they are the same for each request. Reviewed-by:
-
Arend van Spriel authored
Instead of determining the limits for scatter-gather MMC transfer request upon each transmit it is now determined during the probe of the SDIO function. Reviewed-by:
-
Arend van Spriel authored
The variable max_seg_sz in brcmf_sdio_buffrw() respresents the maximum number of buffers that can be sent in one MMC transfer request. Rename it to max_seg_cnt to avoid confusion. Reviewed-by:
-
Arend van Spriel authored
Having the SDPCM header information in the traces is a valuable piece of information. Reviewed-by:
-
Arend van Spriel authored
The trace function trace_brcmf_hexdump() stores the length, but having the address of the buffer being dumped helps putting it in context. Reviewed-by:
-
Luis R. Rodriguez authored
TX99 support enables Specific Absorption Rate (SAR) testing. SAR is the unit of measurement for the amount of radio frequency(RF) absorbed by the body when using a wireless device. The RF exposure limits used are expressed in the terms of SAR, which is a measure of the electric and magnetic field strength and power density for transmitters operating at frequencies from 300 kHz to 100 GHz. Regulatory bodies around the world require that wireless device be evaluated to meet the RF exposure limits set forth in the governmental SAR regulations. In the examples below, for more bit rate options see the iw TX bitrate setting documentation: http://wireless.kernel.org/en/users/Documentation/iw#Modifying_transmit_bitrates Example usage: iw phy phy0 interface add moni0 type monitor ip link set dev moni0 up iw dev moni0 set channel 36 HT40+ iw set bitrates mcs-5 4 echo 10 > /sys/kernel/debug/ieee80211/phy0/ath9k/tx99_power echo 1 > /sys/kernel/debug/ieee80211/phy0/ath9k/tx99 Signed-off-by:
Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by:
Luis R. Rodriguez <mcgrof@do-not-panic.com> Signed-off-by:
-
Luis R. Rodriguez authored
ieee80211_get_rts_cts_rate() can return NULL, so don't rely on its members when it does return NULL. Signed-off-by:
-
Luis R. Rodriguez authored
This enables support for dynamic user regulatory hints. This is enabled only when CFG80211_CERTIFICATION_ONUS is selected. For US and JP this is explicitly disabled unless the systems are being used for strict controlled testing. Signed-off-by:
-
