- 30 Aug, 2017 3 commits
-
-
Andreas Born authored
[ Upstream commit 11e9d782 ] bond_miimon_commit() handles the UP transition for each slave of a bond in the case of MII. It is triggered 10 times per second for the default MII Polling interval of 100ms. For device drivers that do not implement __ethtool_get_link_ksettings() the call to bond_update_speed_duplex() fails persistently while the MII status could remain UP. That is, in this and other cases where the speed/duplex update keeps failing over a longer period of time while the MII state is UP, a warning is printed every MII polling interval. To address these excessive warnings net_ratelimit() should be used. Printing a warning once would not be sufficient since the call to bond_update_speed_duplex() could recover to succeed and fail again later. In that case there would be no new indication what went wrong. Fixes: b5bf0f5b (bonding: correctly update link status during mii-commit phase) Signed-off-by:
Andreas Born <futur.andy@googlemail.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Andreas Born authored
[ Upstream commit ad729bc9 ] The patch c4adfc82 ("bonding: make speed, duplex setting consistent with link state") puts the link state to down if bond_update_speed_duplex() cannot retrieve speed and duplex settings. Assumably the patch was written with 802.3ad mode in mind which relies on link speed/duplex settings. For other modes like active-backup these settings are not required. Thus, only for these other modes, this patch reintroduces support for slaves that do not support reporting speed or duplex such as wireless devices. This fixes the regression reported in bug 196547 (https://bugzilla.kernel.org/show_bug.cgi?id=196547). Fixes: c4adfc82 ("bonding: make speed, duplex setting consistent with link state") Signed-off-by:
Mahesh Bandewar <maheshb@google.com> Signed-off-by:
-
Tushar Dave authored
[ Upstream commit 6170a506 ] There is no need to log message if ATU hvapi couldn't get register. Unlike PCI hvapi, ATU hvapi registration failure is not hard error. Even if ATU hvapi registration fails (on system with ATU or without ATU) system continues with legacy IOMMU. So only log message when ATU hvapi successfully get registered. Signed-off-by:
Tushar Dave <tushar.n.dave@oracle.com> Signed-off-by:
-
- 25 Aug, 2017 37 commits
-
-
Greg Kroah-Hartman authored
-
Hector Martin authored
commit bed9ff16 upstream. Signed-off-by:
Hector Martin <marcan@marcan.st> Signed-off-by:
-
Mathias Nyman authored
commit ed18c5fa upstream. This optimization significantly reduces xhci driver load time. In ACPI tables the acpi companion port devices are children of the hub device. The port devices are identified by their port number returned by the ACPI _ADR method. _ADR 0 is reserved for the root hub device. The current implementation to find a acpi companion port device loops through all acpi port devices under that parent hub, evaluating their _ADR method each time a new port device is added. for a xHC controller with 25 ports under its roothub it will end up invoking ACPI bytecode 625 times before all ports are ready, making it really slow. The _ADR values are already read and cached earler. So instead of running the bytecode again we can check the cached _ADR value first, and then fall back to the old way. As one of the more significant changes, the xhci load time on Intel kabylake reduced by 70%, (28ms) from initcall xhci_pci_init+0x0/0x49 returned 0 after 39537 usecs to initcall xhci_pci_init+0x0/0x49 returned 0 after 11270 usecs Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Josh Poimboeuf authored
commit 325cdacd upstream. Mike Galbraith reported a situation where a WARN_ON_ONCE() call in DRM code turned into an oops. As it turns out, WARN_ON_ONCE() seems to be completely broken when called from a module. The bug was introduced with the following commit: 19d43626 ("debug: Add _ONCE() logic to report_bug()") That commit changed WARN_ON_ONCE() to move its 'once' logic into the bug trap handler. It requires a writable bug table so that the BUGFLAG_DONE bit can be written to the flags to indicate the first warning has occurred. The bug table was made writable for vmlinux, which relies on vmlinux.lds.S and vmlinux.lds.h for laying out the sections. However, it wasn't made writable for modules, which rely on the ELF section header flags. Reported-by:
Mike Galbraith <efault@gmx.de> Tested-by:
Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by:
Josh Poimboeuf <jpoimboe@redhat.com> Acked-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 19d43626 ("debug: Add _ONCE() logic to report_bug()") Link: http://lkml.kernel.org/r/a53b04235a65478dd9afc51f5b329fdc65c84364.1500095401.git.jpoimboe@redhat.comSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
Changbin Du <changbin.du@intel.com> Signed-off-by:
-
Oleg Nesterov authored
commit dd1c1f2f upstream. This was reported many times, and this was even mentioned in commit 52ee2dfd ("pids: refactor vnr/nr_ns helpers to make them safe") but somehow nobody bothered to fix the obvious problem: task_tgid_nr_ns() is not safe because task->group_leader points to nowhere after the exiting task passes exit_notify(), rcu_read_lock() can not help. We really need to change __unhash_process() to nullify group_leader, parent, and real_parent, but this needs some cleanups. Until then we can turn task_tgid_nr_ns() into another user of __task_pid_nr_ns() and fix the problem. Reported-by:
Troy Kensinger <tkensinger@google.com> Signed-off-by:
Oleg Nesterov <oleg@redhat.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Linus Torvalds authored
commit 197e7e52 upstream. The 'move_paghes()' system call was introduced long long ago with the same permission checks as for sending a signal (except using CAP_SYS_NICE instead of CAP_SYS_KILL for the overriding capability). That turns out to not be a great choice - while the system call really only moves physical page allocations around (and you need other capabilities to do a lot of it), you can check the return value to map out some the virtual address choices and defeat ASLR of a binary that still shares your uid. So change the access checks to the more common 'ptrace_may_access()' model instead. This tightens the access checks for the uid, and also effectively changes the CAP_SYS_NICE check to CAP_SYS_PTRACE, but it's unlikely that anybody really _uses_ this legacy system call any more (we hav ebetter NUMA placement models these days), so I expect nobody to notice. Famous last words. Reported-by:
Otto Ebeling <otto.ebeling@iki.fi> Acked-by:
Eric W. Biederman <ebiederm@xmission.com> Cc: Willy Tarreau <w@1wt.eu> Signed-off-by:
-
Thomas Gleixner authored
commit 7edaeb68 upstream. The hardlockup detector on x86 uses a performance counter based on unhalted CPU cycles and a periodic hrtimer. The hrtimer period is about 2/5 of the performance counter period, so the hrtimer should fire 2-3 times before the performance counter NMI fires. The NMI code checks whether the hrtimer fired since the last invocation. If not, it assumess a hard lockup. The calculation of those periods is based on the nominal CPU frequency. Turbo modes increase the CPU clock frequency and therefore shorten the period of the perf/NMI watchdog. With extreme Turbo-modes (3x nominal frequency) the perf/NMI period is shorter than the hrtimer period which leads to false positives. A simple fix would be to shorten the hrtimer period, but that comes with the side effect of more frequent hrtimer and softlockup thread wakeups, which is not desired. Implement a low pass filter, which checks the perf/NMI period against kernel time. If the perf/NMI fires before 4/5 of the watchdog period has elapsed then the event is ignored and postponed to the next perf/NMI. That solves the problem and avoids the overhead of shorter hrtimer periods and more frequent softlockup thread wakeups. Fixes: 58687acb ("lockup_detector: Combine nmi_watchdog and softlockup detector") Reported-and-tested-by:
Kan Liang <Kan.liang@intel.com> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Cc: dzickus@redhat.com Cc: prarit@redhat.com Cc: ak@linux.intel.com Cc: babu.moger@oracle.com Cc: peterz@infradead.org Cc: eranian@google.com Cc: acme@redhat.com Cc: atomlin@redhat.com Cc: akpm@linux-foundation.org Cc: torvalds@linux-foundation.org Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1708150931310.1886@nanosSigned-off-by:
-
Alexey Dobriyan authored
commit 8fbbe2d7 upstream. Valid CPU ids are [0, nr_cpu_ids-1] inclusive. Fixes: 3b8e29a8 ("genirq: Implement ipi_send_mask/single()") Fixes: f9bce791 ("genirq: Add a new function to get IPI reverse mapping") Signed-off-by:
Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by:
-
Marc Zyngier authored
commit e8f24189 upstream. irq_modify_status starts by clearing the trigger settings from irq_data before applying the new settings, but doesn't restore them, leaving them to IRQ_TYPE_NONE. That's pretty confusing to the potential request_irq() that could follow. Instead, snapshot the settings before clearing them, and restore them if the irq_modify_status() invocation was not changing the trigger. Fixes: 1e2a7d78 ("irqdomain: Don't set type when mapping an IRQ") Reported-and-tested-by:
jeffy <jeffy.chen@rock-chips.com> Signed-off-by:
Marc Zyngier <marc.zyngier@arm.com> Signed-off-by:
-
Boris Brezillon authored
commit 277867ad upstream. of_find_compatible_node() is calling of_node_put() on its first argument thus leading to an unbalanced of_node_get/put() issue if the node has not been retained before that. Instead of passing the root node, pass NULL, which does exactly the same: iterate over all DT nodes, starting from the root node. Signed-off-by:
Boris Brezillon <boris.brezillon@free-electrons.com> Reported-by:
Alexandre Belloni <alexandre.belloni@free-electrons.com> Fixes: 3d61467f ("irqchip: atmel-aic: Implement RTC irq fixup") Signed-off-by:
-
Boris Brezillon authored
commit 469bcef5 upstream. aic_common_irq_fixup() is calling twice of_node_put() on the same node thus leading to an unbalanced refcount on the root node. Signed-off-by:
-
Oleg Nesterov authored
commit 01578e36 upstream. The ADDR_NO_RANDOMIZE checks in stack_maxrandom_size() and randomize_stack_top() are not required. PF_RANDOMIZE is set by load_elf_binary() only if ADDR_NO_RANDOMIZE is not set, no need to re-check after that. Signed-off-by:
Dmitry Safonov <dsafonov@virtuozzo.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Borislav Petkov <bp@suse.de> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Link: http://lkml.kernel.org/r/20170815154011.GB1076@redhat.comSigned-off-by:
-
Oleg Nesterov authored
commit 47ac5484 upstream. Documentation/admin-guide/kernel-parameters.txt says: norandmaps Don't use address space randomization. Equivalent to echo 0 > /proc/sys/kernel/randomize_va_space but it doesn't work because arch_rnd() which is used to randomize mm->mmap_base returns a random value unconditionally. And as Kirill pointed out, ADDR_NO_RANDOMIZE is broken by the same reason. Just shift the PF_RANDOMIZE check from arch_mmap_rnd() to arch_rnd(). Fixes: 1b028f78 ("x86/mm: Introduce mmap_compat_base() for 32-bit mmap()") Signed-off-by:
Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Acked-by:
Cyrill Gorcunov <gorcunov@openvz.org> Reviewed-by:
-
Andy Lutomirski authored
commit e93c1730 upstream. This closes a hole in our SMAP implementation. This patch comes from grsecurity. Good catch! Signed-off-by:
Andy Lutomirski <luto@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Josh Poimboeuf <jpoimboe@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/314cc9f294e8f14ed85485727556ad4f15bb1659.1502159503.git.luto@kernel.orgSigned-off-by:
-
Peter Zijlstra authored
commit bfe33492 upstream. Vince reported the following rdpmc() testcase failure: > Failing test case: > > fd=perf_event_open(); > addr=mmap(fd); > exec() // without closing or unmapping the event > fd=perf_event_open(); > addr=mmap(fd); > rdpmc() // GPFs due to rdpmc being disabled The problem is of course that exec() plays tricks with what is current->mm, only destroying the old mappings after having installed the new mm. Fix this confusion by passing along vma->vm_mm instead of relying on current->mm. Reported-by:
Vince Weaver <vincent.weaver@maine.edu> Tested-by:
-
Munehisa Kamata authored
commit b15bd8cb upstream. Since commit d05d7f40 ("Merge branch 'for-4.8/core' of git://git.kernel.dk/linux-block") and 3fc9d690 ("Merge branch 'for-4.8/drivers' of git://git.kernel.dk/linux-block"), blkfront_resume() has been using an index for iterating ring_info to check request when iterating blk_shadow in an inner loop. This seems to have been accidentally introduced during the massive rewrite of the block layer macros in the commits. This may cause crash like this: [11798.057074] BUG: unable to handle kernel NULL pointer dereference at 0000000000000048 [11798.058832] IP: [<ffffffff814411fa>] blkfront_resume+0x10a/0x610 .... [11798.061063] Call Trace: [11798.061063] [<ffffffff8139ce93>] xenbus_dev_resume+0x53/0x140 [11798.061063] [<ffffffff8139ce40>] ? xenbus_dev_probe+0x150/0x150 [11798.061063] [<ffffffff813f359e>] dpm_run_callback+0x3e/0x110 [11798.061063] [<ffffffff813f3a08>] device_resume+0x88/0x190 [11798.061063] [<ffffffff813f4cc0>] dpm_resume+0x100/0x2d0 [11798.061063] [<ffffffff813f5221>] dpm_resume_end+0x11/0x20 [11798.061063] [<ffffffff813950a8>] do_suspend+0xe8/0x1a0 [11798.061063] [<ffffffff813954bd>] shutdown_handler+0xfd/0x130 [11798.061063] [<ffffffff8139aba0>] ? split+0x110/0x110 [11798.061063] [<ffffffff8139ac26>] xenwatch_thread+0x86/0x120 [11798.061063] [<ffffffff810b4570>] ? prepare_to_wait_event+0x110/0x110 [11798.061063] [<ffffffff8108fe57>] kthread+0xd7/0xf0 [11798.061063] [<ffffffff811da811>] ? kfree+0x121/0x170 [11798.061063] [<ffffffff8108fd80>] ? kthread_park+0x60/0x60 [11798.061063] [<ffffffff810863b0>] ? call_usermodehelper_exec_work+0xb0/0xb0 [11798.061063] [<ffffffff810864ea>] ? call_usermodehelper_exec_async+0x13a/0x140 [11798.061063] [<ffffffff81534a45>] ret_from_fork+0x25/0x30 Use the right index in the inner loop. Fixes: d05d7f40 ("Merge branch 'for-4.8/core' of git://git.kernel.dk/linux-block") Fixes: 3fc9d690 ("Merge branch 'for-4.8/drivers' of git://git.kernel.dk/linux-block") Signed-off-by:
Munehisa Kamata <kamatam@amazon.com> Reviewed-by:
Thomas Friebel <friebelt@amazon.de> Reviewed-by:
Eduardo Valentin <eduval@amazon.com> Reviewed-by:
Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Juergen Gross <jgross@suse.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Reviewed-by:
Roger Pau Monne <roger.pau@citrix.com> Cc: xen-devel@lists.xenproject.org Signed-off-by:
Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by:
-
Benjamin Herrenschmidt authored
commit 5a69aec9 upstream. VSX uses a combination of the old vector registers, the old FP registers and new "second halves" of the FP registers. Thus when we need to see the VSX state in the thread struct (flush_vsx_to_thread()) or when we'll use the VSX in the kernel (enable_kernel_vsx()) we need to ensure they are all flushed into the thread struct if either of them is individually enabled. Unfortunately we only tested if the whole VSX was enabled, not if they were individually enabled. Fixes: 72cd7b44 ("powerpc: Uncomment and make enable_kernel_vsx() routine available") Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Christoph Hellwig authored
commit c0053903 upstream. While pci_irq_get_affinity should never fail for SMP kernel that implement the affinity mapping, it will always return NULL in the UP case, so provide a fallback mapping of all queues to CPU 0 in that case. Signed-off-by:
Christoph Hellwig <hch@lst.de> Reviewed-by:
Omar Sandoval <osandov@fb.com> Signed-off-by:
Jens Axboe <axboe@kernel.dk> Signed-off-by:
-
Gary Bisson authored
commit c40bc54f upstream. Previous value was a bad copy of nitrogen6_max device tree. Signed-off-by:
Gary Bisson <gary.bisson@boundarydevices.com> Fixes: 3faa1bb2 ("ARM: dts: imx: add Boundary Devices Nitrogen6_SOM2 support") Signed-off-by:
Shawn Guo <shawnguo@kernel.org> Signed-off-by:
-
Roger Pau Monne authored
commit 462cdace upstream. The current test for bio vec merging is not fully accurate and can be tricked into merging bios when certain grant combinations are used. The result of these malicious bio merges is a bio that extends past the memory page used by any of the originating bios. Take into account the following scenario, where a guest creates two grant references that point to the same mfn, ie: grant 1 -> mfn A, grant 2 -> mfn A. These references are then used in a PV block request, and mapped by the backend domain, thus obtaining two different pfns that point to the same mfn, pfn B -> mfn A, pfn C -> mfn A. If those grants happen to be used in two consecutive sectors of a disk IO operation becoming two different bios in the backend domain, the checks in xen_biovec_phys_mergeable will succeed, because bfn1 == bfn2 (they both point to the same mfn). However due to the bio merging, the backend domain will end up with a bio that expands past mfn A into mfn A + 1. Fix this by making sure the check in xen_biovec_phys_mergeable takes into account the offset and the length of the bio, this basically replicates whats done in __BIOVEC_PHYS_MERGEABLE using mfns (bus addresses). While there also remove the usage of __BIOVEC_PHYS_MERGEABLE, since that's already checked by the callers of xen_biovec_phys_mergeable. Reported-by:
"Jan H. Schönherr" <jschoenh@amazon.de> Signed-off-by:
Juergen Gross <jgross@suse.com> Signed-off-by:
-
Kees Cook authored
commit c715b72c upstream. Moving the x86_64 and arm64 PIE base from 0x555555554000 to 0x000100000000 broke AddressSanitizer. This is a partial revert of: eab09532 ("binfmt_elf: use ELF_ET_DYN_BASE only for PIE") 02445990 ("arm64: move ELF_ET_DYN_BASE to 4GB / 4MB") The AddressSanitizer tool has hard-coded expectations about where executable mappings are loaded. The motivation for changing the PIE base in the above commits was to avoid the Stack-Clash CVEs that allowed executable mappings to get too close to heap and stack. This was mainly a problem on 32-bit, but the 64-bit bases were moved too, in an effort to proactively protect those systems (proofs of concept do exist that show 64-bit collisions, but other recent changes to fix stack accounting and setuid behaviors will minimize the impact). The new 32-bit PIE base is fine for ASan (since it matches the ET_EXEC base), so only the 64-bit PIE base needs to be reverted to let x86 and arm64 ASan binaries run again. Future changes to the 64-bit PIE base on these architectures can be made optional once a more dynamic method for dealing with AddressSanitizer is found. (e.g. always loading PIE into the mmap region for marked binaries.) Link: http://lkml.kernel.org/r/20170807201542.GA21271@beast Fixes: eab09532 ("binfmt_elf: use ELF_ET_DYN_BASE only for PIE") Fixes: 02445990 ("arm64: move ELF_ET_DYN_BASE to 4GB / 4MB") Signed-off-by:
Kees Cook <keescook@chromium.org> Reported-by:
Kostya Serebryany <kcc@google.com> Acked-by:
Will Deacon <will.deacon@arm.com> Cc: Ingo Molnar <mingo@elte.hu> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Laura Abbott authored
commit 704b862f upstream. Commit 19809c2d ("mm, vmalloc: use __GFP_HIGHMEM implicitly") added use of __GFP_HIGHMEM for allocations. vmalloc_32 may use GFP_DMA/GFP_DMA32 which does not play nice with __GFP_HIGHMEM and will trigger a BUG in gfp_zone. Only add __GFP_HIGHMEM if we aren't using GFP_DMA/GFP_DMA32. Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1482249 Link: http://lkml.kernel.org/r/20170816220705.31374-1-labbott@redhat.com Fixes: 19809c2d ("mm, vmalloc: use __GFP_HIGHMEM implicitly") Signed-off-by:
Laura Abbott <labbott@redhat.com> Acked-by:
Michal Hocko <mhocko@suse.com> Cc: Vlastimil Babka <vbabka@suse.cz> Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com> Signed-off-by:
-
zhong jiang authored
commit 73223e4e upstream. I hit a use after free issue when executing trinity and repoduced it with KASAN enabled. The related call trace is as follows. BUG: KASan: use after free in SyS_get_mempolicy+0x3c8/0x960 at addr ffff8801f582d766 Read of size 2 by task syz-executor1/798 INFO: Allocated in mpol_new.part.2+0x74/0x160 age=3 cpu=1 pid=799 __slab_alloc+0x768/0x970 kmem_cache_alloc+0x2e7/0x450 mpol_new.part.2+0x74/0x160 mpol_new+0x66/0x80 SyS_mbind+0x267/0x9f0 system_call_fastpath+0x16/0x1b INFO: Freed in __mpol_put+0x2b/0x40 age=4 cpu=1 pid=799 __slab_free+0x495/0x8e0 kmem_cache_free+0x2f3/0x4c0 __mpol_put+0x2b/0x40 SyS_mbind+0x383/0x9f0 system_call_fastpath+0x16/0x1b INFO: Slab 0xffffea0009cb8dc0 objects=23 used=8 fp=0xffff8801f582de40 flags=0x200000000004080 INFO: Object 0xffff8801f582d760 @offset=5984 fp=0xffff8801f582d600 Bytes b4 ffff8801f582d750: ae 01 ff ff 00 00 00 00 5a 5a 5a 5a 5a 5a 5a 5a ........ZZZZZZZZ Object ffff8801f582d760: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk Object ffff8801f582d770: 6b 6b 6b 6b 6b 6b 6b a5 kkkkkkk. Redzone ffff8801f582d778: bb bb bb bb bb bb bb bb ........ Padding ffff8801f582d8b8: 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZ Memory state around the buggy address: ffff8801f582d600: fb fb fb fc fc fc fc fc fc fc fc fc fc fc fc fc ffff8801f582d680: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc >ffff8801f582d700: fc fc fc fc fc fc fc fc fc fc fc fc fb fb fb fc !shared memory policy is not protected against parallel removal by other thread which is normally protected by the mmap_sem. do_get_mempolicy, however, drops the lock midway while we can still access it later. Early premature up_read is a historical artifact from times when put_user was called in this path see https://lwn.net/Articles/124754/ but that is gone since 8bccd85f ("[PATCH] Implement sys_* do_* layering in the memory policy layer."). but when we have the the current mempolicy ref count model. The issue was introduced accordingly. Fix the issue by removing the premature release. Link: http://lkml.kernel.org/r/1502950924-27521-1-git-send-email-zhongjiang@huawei.comSigned-off-by:
zhong jiang <zhongjiang@huawei.com> Acked-by:
-
Prakash Gupta authored
commit da094e42 upstream. name[] in cma_debugfs_add_one() can only accommodate 16 chars including NULL to store sprintf output. It's common for cma device name to be larger than 15 chars. This can cause stack corrpution. If the gcc stack protector is turned on, this can cause a panic due to stack corruption. Below is one example trace: Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: ffffff8e69a75730 Call trace: dump_backtrace+0x0/0x2c4 show_stack+0x20/0x28 dump_stack+0xb8/0xf4 panic+0x154/0x2b0 print_tainted+0x0/0xc0 cma_debugfs_init+0x274/0x290 do_one_initcall+0x5c/0x168 kernel_init_freeable+0x1c8/0x280 Fix the short sprintf buffer in cma_debugfs_add_one() by using scnprintf() instead of sprintf(). Link: http://lkml.kernel.org/r/1502446217-21840-1-git-send-email-guptap@codeaurora.org Fixes: f318dd08 ("cma: Store a name in the cma structure") Signed-off-by:
Prakash Gupta <guptap@codeaurora.org> Acked-by:
-
Michal Hocko authored
commit 5b53a6ea upstream. Tetsuo Handa has noticed that MMF_UNSTABLE SIGBUS path in handle_mm_fault causes a lockdep splat Out of memory: Kill process 1056 (a.out) score 603 or sacrifice child Killed process 1056 (a.out) total-vm:4268108kB, anon-rss:2246048kB, file-rss:0kB, shmem-rss:0kB a.out (1169) used greatest stack depth: 11664 bytes left DEBUG_LOCKS_WARN_ON(depth <= 0) ------------[ cut here ]------------ WARNING: CPU: 6 PID: 1339 at kernel/locking/lockdep.c:3617 lock_release+0x172/0x1e0 CPU: 6 PID: 1339 Comm: a.out Not tainted 4.13.0-rc3-next-20170803+ #142 Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 07/02/2015 RIP: 0010:lock_release+0x172/0x1e0 Call Trace: up_read+0x1a/0x40 __do_page_fault+0x28e/0x4c0 do_page_fault+0x30/0x80 page_fault+0x28/0x30 The reason is that the page fault path might have dropped the mmap_sem and returned with VM_FAULT_RETRY. MMF_UNSTABLE check however rewrites the error path to VM_FAULT_SIGBUS and we always expect mmap_sem taken in that path. Fix this by taking mmap_sem when VM_FAULT_RETRY is held in the MMF_UNSTABLE path. We cannot simply add VM_FAULT_SIGBUS to the existing error code because all arch specific page fault handlers and g-u-p would have to learn a new error code combination. Link: http://lkml.kernel.org/r/20170807113839.16695-2-mhocko@kernel.org Fixes: 3f70dc38 ("mm: make sure that kthreads will not refault oom reaped memory") Reported-by:
Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp> Signed-off-by:
David Rientjes <rientjes@google.com> Cc: Andrea Argangeli <andrea@kernel.org> Cc: "Kirill A. Shutemov" <kirill@shutemov.name> Cc: Oleg Nesterov <oleg@redhat.com> Cc: Wenwei Tao <wenwei.tww@alibaba-inc.com> Signed-off-by:
-
Vladimir Davydov authored
commit f6ba4880 upstream. To avoid a possible deadlock, sysfs_slab_remove() schedules an asynchronous work to delete sysfs entries corresponding to the kmem cache. To ensure the cache isn't freed before the work function is called, it takes a reference to the cache kobject. The reference is supposed to be released by the work function. However, the work function (sysfs_slab_remove_workfn()) does nothing in case the cache sysfs entry has already been deleted, leaking the kobject and the corresponding cache. This may happen on a per memcg cache destruction, because sysfs entries of a per memcg cache are deleted on memcg offline if the cache is empty (see __kmemcg_cache_deactivate()). The kmemleak report looks like this: unreferenced object 0xffff9f798a79f540 (size 32): comm "kworker/1:4", pid 15416, jiffies 4307432429 (age 28687.554s) hex dump (first 32 bytes): 6b 6d 61 6c 6c 6f 63 2d 31 36 28 31 35 39 39 3a kmalloc-16(1599: 6e 65 77 72 6f 6f 74 29 00 23 6b c0 ff ff ff ff newroot).#k..... backtrace: kmemleak_alloc+0x4a/0xa0 __kmalloc_track_caller+0x148/0x2c0 kvasprintf+0x66/0xd0 kasprintf+0x49/0x70 memcg_create_kmem_cache+0xe6/0x160 memcg_kmem_cache_create_func+0x20/0x110 process_one_work+0x205/0x5d0 worker_thread+0x4e/0x3a0 kthread+0x109/0x140 ret_from_fork+0x2a/0x40 unreferenced object 0xffff9f79b6136840 (size 416): comm "kworker/1:4", pid 15416, jiffies 4307432429 (age 28687.573s) hex dump (first 32 bytes): 40 fb 80 c2 3e 33 00 00 00 00 00 40 00 00 00 00 @...>3.....@.... 00 00 00 00 00 00 00 00 10 00 00 00 10 00 00 00 ................ backtrace: kmemleak_alloc+0x4a/0xa0 kmem_cache_alloc+0x128/0x280 create_cache+0x3b/0x1e0 memcg_create_kmem_cache+0x118/0x160 memcg_kmem_cache_create_func+0x20/0x110 process_one_work+0x205/0x5d0 worker_thread+0x4e/0x3a0 kthread+0x109/0x140 ret_from_fork+0x2a/0x40 Fix the leak by adding the missing call to kobject_put() to sysfs_slab_remove_workfn(). Link: http://lkml.kernel.org/r/20170812181134.25027-1-vdavydov.dev@gmail.com Fixes: 3b7b3140 ("slub: make sysfs file removal asynchronous") Signed-off-by:
Vladimir Davydov <vdavydov.dev@gmail.com> Reported-by:
Andrei Vagin <avagin@gmail.com> Tested-by:
Tejun Heo <tj@kernel.org> Acked-by:
-
Pavel Tatashin authored
commit 3010f876 upstream. There is existing use after free bug when deferred struct pages are enabled: The memblock_add() allocates memory for the memory array if more than 128 entries are needed. See comment in e820__memblock_setup(): * The bootstrap memblock region count maximum is 128 entries * (INIT_MEMBLOCK_REGIONS), but EFI might pass us more E820 entries * than that - so allow memblock resizing. This memblock memory is freed here: free_low_memory_core_early() We access the freed memblock.memory later in boot when deferred pages are initialized in this path: deferred_init_memmap() for_each_mem_pfn_range() __next_mem_pfn_range() type = &memblock.memory; One possible explanation for why this use-after-free hasn't been hit before is that the limit of INIT_MEMBLOCK_REGIONS has never been exceeded at least on systems where deferred struct pages were enabled. Tested by reducing INIT_MEMBLOCK_REGIONS down to 4 from the current 128, and verifying in qemu that this code is getting excuted and that the freed pages are sane. Link: http://lkml.kernel.org/r/1502485554-318703-2-git-send-email-pasha.tatashin@oracle.com Fixes: 7e18adb4 ("mm: meminit: initialise remaining struct pages in parallel with kswapd") Signed-off-by:
Pavel Tatashin <pasha.tatashin@oracle.com> Reviewed-by:
Steven Sistare <steven.sistare@oracle.com> Reviewed-by:
Daniel Jordan <daniel.m.jordan@oracle.com> Reviewed-by:
Bob Picco <bob.picco@oracle.com> Acked-by:
-
Jussi Laako authored
commit ed993c6f upstream. Add DSD support for new Amanero Combo384 firmware version with a new PID. This firmware uses DSD_U32_BE. Fixes: 3eff682d ("ALSA: usb-audio: Support both DSD LE/BE Amanero firmware versions") Signed-off-by:
Jussi Laako <jussi@sonarnerd.net> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Takashi Iwai authored
commit 0f174b35 upstream. C-Media devices (at least some models) mute the playback stream when volumes are set to the minimum value. But this isn't informed via TLV and the user-space, typically PulseAudio, gets confused as if it's still played in a low volume. This patch adds the new flag, min_mute, to struct usb_mixer_elem_info for indicating that the mixer element is with the minimum-mute volume. This flag is set for known C-Media devices in snd_usb_mixer_fu_apply_quirk() in turn. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=196669Signed-off-by:
-
Takashi Iwai authored
commit a8e800fe upstream. A Senheisser headset requires the typical sample-rate quirk for avoiding spurious errors from inquiring the current sample rate like: usb 1-1: 2:1: cannot get freq at ep 0x4 usb 1-1: 3:1: cannot get freq at ep 0x83 The USB ID 1395:740a has to be added to the entries in snd_usb_get_sample_rate_quirk(). Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=1052580Signed-off-by:
-
Daniel Mentz authored
commit 7e1d90f6 upstream. commit 4842e98f ("ALSA: seq: Fix race at creating a queue") attempted to fix a race reported by syzkaller. That fix has been described as follows: " When a sequencer queue is created in snd_seq_queue_alloc(),it adds the new queue element to the public list before referencing it. Thus the queue might be deleted before the call of snd_seq_queue_use(), and it results in the use-after-free error, as spotted by syzkaller. The fix is to reference the queue object at the right time. " Even with that fix in place, syzkaller reported a use-after-free error. It specifically pointed to the last instruction "return q->queue" in snd_seq_queue_alloc(). The pointer q is being used after kfree() has been called on it. It turned out that there is still a small window where a race can happen. The window opens at snd_seq_ioctl_create_queue()->snd_seq_queue_alloc()->queue_list_add() and closes at snd_seq_ioctl_create_queue()->queueptr()->snd_use_lock_use(). Between these two calls, a different thread could delete the queue and possibly re-create a different queue in the same location in queue_list. This change prevents this situation by calling snd_use_lock_use() from snd_seq_queue_alloc() prior to calling queue_list_add(). It is then the caller's responsibility to call snd_use_lock_free(&q->use_lock). Fixes: 4842e98f ("ALSA: seq: Fix race at creating a queue") Reported-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
Daniel Mentz <danielmentz@google.com> Signed-off-by:
-
Shaohua Li authored
commit afc1f55c upstream. ->safemode should be triggered by mdadm for external metadaa array, otherwise array's state confuses mdadm. Fixes: 33182d15(md: always clear ->safemode when md_check_recovery gets the mddev lock.) Cc: NeilBrown <neilb@suse.com> Signed-off-by:
Shaohua Li <shli@fb.com> Signed-off-by:
-
NeilBrown authored
commit 33182d15 upstream. If ->safemode == 1, md_check_recovery() will try to get the mddev lock and perform various other checks. If mddev->in_sync is zero, it will call set_in_sync, and clear ->safemode. However if mddev->in_sync is not zero, ->safemode will not be cleared. When md_check_recovery() drops the mddev lock, the thread is woken up again. Normally it would just check if there was anything else to do, find nothing, and go to sleep. However as ->safemode was not cleared, it will take the mddev lock again, then wake itself up when unlocking. This results in an infinite loop, repeatedly calling md_check_recovery(), which RCU or the soft-lockup detector will eventually complain about. Prior to commit 4ad23a97 ("MD: use per-cpu counter for writes_pending"), safemode would only be set to one when the writes_pending counter reached zero, and would be cleared again when writes_pending is incremented. Since that patch, safemode is set more freely, but is not reliably cleared. So in md_check_recovery() clear ->safemode before checking ->in_sync. Fixes: 4ad23a97 ("MD: use per-cpu counter for writes_pending") Reported-by:
Dominik Brodowski <linux@dominikbrodowski.net> Reported-by:
David R <david@unsolicited.net> Signed-off-by:
NeilBrown <neilb@suse.com> Signed-off-by:
-
NeilBrown authored
commit 81fe48e9 upstream. md_write_start() needs to clear the in_sync flag is it is set, or if there might be a race with set_in_sync() such that the later will set it very soon. In the later case it is sufficient to take the spinlock to synchronize with set_in_sync(), and then set the flag if needed. The current test is incorrect. It should be: if "flag is set" or "race is possible" "flag is set" is trivially "mddev->in_sync". "race is possible" should be tested by "mddev->sync_checkers". If sync_checkers is 0, then there can be no race. set_in_sync() will wait in percpu_ref_switch_to_atomic_sync() for an RCU grace period, and as md_write_start() holds the rcu_read_lock(), set_in_sync() will be sure ot see the update to writes_pending. If sync_checkers is > 0, there could be race. If md_write_start() happened entirely between if (!mddev->in_sync && percpu_ref_is_zero(&mddev->writes_pending)) { and mddev->in_sync = 1; in set_in_sync(), then it would not see that is_sync had been set, and set_in_sync() would not see that writes_pending had been incremented. This bug means that in_sync is sometimes not set when it should be. Consequently there is a small chance that the array will be marked as "clean" when in fact it is inconsistent. Fixes: 4ad23a97 ("MD: use per-cpu counter for writes_pending") Signed-off-by:
-
KT Liao authored
commit 76988690 upstream. Add 2 new IDs (ELAN0609 and ELAN060B) to the list of ACPI IDs that should be handled by the driver. Signed-off-by:
KT Liao <kt.liao@emc.com.tw> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Kai-Heng Feng authored
commit 1874064e upstream. Similar to commit 722c5ac7 ("Input: elan_i2c - add ELAN0605 to the ACPI table"), ELAN0608 should be handled by elan_i2c. This touchpad can be found in Lenovo ideapad 320-14IKB. BugLink: https://bugs.launchpad.net/bugs/1708852Signed-off-by:
Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by:
-
Chunming Zhou authored
commit 7a7c286d upstream. update the list first to avoid redundant checks. Signed-off-by:
Chunming Zhou <David1.Zhou@amd.com> Reviewed-by:
Christian König <christian.koenig@amd.com> Reviewed-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
