- 07 Jan, 2013 40 commits
-
-
Hauke Mehrtens authored
Signed-off-by:
Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Hauke Mehrtens authored
The assignment of the IRQs to the cores of the chips by iterating over the cores is complicated and causes problems with SoC like the BCM4706 with two GMAC core where just one should get a dedicated IRQ number. Now the code assigns the same IRQs to the cores as the code from the Broadcom SDK does. If the SoC is not know the current assigned IRQs are only read out and an error message is printed. Signed-off-by:
-
Hauke Mehrtens authored
This bcma_find_core_unit() is needed by the mips driver in the next patch. Signed-off-by:
-
Sujith Manoharan authored
TX_IQ_ON_AGC_CAL should not be enabled for AR9340. TX-IQ calibration is run as part of AGC calibration only for AR9485, AR9462 and AR9565. For the others (AR9300, AR9330, AR9340), TX-IQ cal is done independent of AGC-cal. Signed-off-by:
Sujith Manoharan <c_manoha@qca.qualcomm.com> Signed-off-by:
-
Yogesh Ashok Powar authored
New firmware is required to support a) Add support for additional ampdu streams b) Handle corresponding watchdog events to destroy ampdu streams Bumping firmware API version by one. Signed-off-by:
Nishant Sarmukadam <nishants@marvell.com> Signed-off-by:
Yogesh Ashok Powar <yogeshp@marvell.com> Signed-off-by:
-
Yogesh Ashok Powar authored
Currently, command path waits till all the tx host queues are empty. Whenever watchdog event is raised, firmware expects driver to destroy ampdu queues immediately. This requires corresponding commands i.e. mwl8k_cmd_get_watchdog_bitmap and mwl8k_destroy_ba to be sent without waiting for the tx queues to be completely empty. Use "watchdog_event_pending" to ensure the above mentioned two commands are sent down immediately. Signed-off-by:
-
Yogesh Ashok Powar authored
With more ampdu streams, we need to handle watchdog events for the new ampdu streams. Handle these events appropriately. Earlier mwl8k_cmd_get_watchdog_bitmap used to return only one stream index and hence bitwise operations on the return value were not required. Now the function returns a bitmap with different bits are mapped with different stream indices. Signed-off-by:
-
Yogesh Ashok Powar authored
Currently, mwl8k_ampdu_stream is passed as one of the argument to the function mwl8k_destroy_ba. Instead of this pass only the stream index. This will be helpful during watchdog event handling when bitmap of stream indices are received. Signed-off-by:
-
Yogesh Ashok Powar authored
Currently, we have 2 ampdu streams that can be created simultaneously. Firmware is capable of supporting additional streams. Add support to use these streams. Signed-off-by:
-
Yogesh Ashok Powar authored
Set ACK policy to NORMAL when its not going to be an AMPDU packet. Signed-off-by:
-
Yogesh Ashok Powar authored
Ampdu stream index can be derived from stream->idx. So we no longer need stream->txq_idx, hence removing it. Signed-off-by:
-
Sujith Manoharan authored
This is not enabled for any chip and is unused. Signed-off-by:
-
Sujith Manoharan authored
Doing this in ath9k_hw_fill_cap_info() is odd and it's cleaner to do this in the init function for calibration. Also, setup the supported calibration type in init_cal_settings. Signed-off-by:
-
Avinash Patil authored
This patch adds support for parsing WMM IEs from hostapd and setting them to FW via sys configure command. Patch also sets wiphy flag to advertise AP uAPSD support. Signed-off-by:
Avinash Patil <patila@marvell.com> Signed-off-by:
Bing Zhao <bzhao@marvell.com> Signed-off-by:
-
Amitkumar Karwar authored
It is observed that same htcapinfo ie is included in beacon for HT20, HT40+ and HT40- ibss networks. This patch makes sure that we will not advertise 40Mhz flags while creating/joining ibss network in HT20 mode. Signed-off-by:
Amitkumar Karwar <akarwar@marvell.com> Signed-off-by:
-
Sasha Levin authored
We know 'firmware' is non-NULL from the beginning of mwifiex_prog_fw_w_helper, remove all !firmware paths from the rest of the function. Signed-off-by:
Sasha Levin <sasha.levin@oracle.com> Signed-off-by:
-
Alexey Khoroshilov authored
If pci_set_dma_mask() or pci_set_consistent_dma_mask() fails in p54p_probe(), it breaks off initialization, deallocates all resources, but returns zero. Similar issue is if check for returned value of pci_resource_len() fails. The patch implements proper error code propagation. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
Alexey Khoroshilov <khoroshilov@ispras.ru> Acked-by:
Christian Lamparter <chunkeey@googlemail.com> Signed-off-by:
-
Hante Meuleman authored
On interface up dongle gets inialized. Move UP command to common routine and update these common init routines using ifp. Reviewed-by:
Arend Van Spriel <arend@broadcom.com> Reviewed-by:
Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by:
Hante Meuleman <meuleman@broadcom.com> Signed-off-by:
-
Hante Meuleman authored
Reviewed-by:
-
Hante Meuleman authored
Netdev xmit routine brcfm_netdev_start_xmit was defined incorrectly and used wrong return codes. Always eat the packet and return ok. Remove drvr_up check since it is not relevant. Reviewed-by:
-
Hante Meuleman authored
CDC errors are retained. However, it is never used so it can be removed. Reviewed-by:
-
Arend van Spriel authored
Stumbled into a curly braces used for if statement with only one conditional statement. Removing them. Reviewed-by:
-
Arend van Spriel authored
The header of the ethernet packet is processed conditionally, but the check is wrong as it checks skb length is at least ETH_ALEN. It should check it is at least sizeof struct ethhdr instead. Reviewed-by:
-
Arend van Spriel authored
The driver had some global definitions in dhd.h to map event identifiers to event names. With redesign of firmware event processing this has all moved to fweh module so these definitions can be removed. Reviewed-by:
-
Hante Meuleman authored
CDC debug is partly done with TRACE and partly with CTL, however CDC hardly ever needs debugging. Use dedicated level CDC and replace TRACE and CTL in dhd_cdc with that. Reviewed-by:
-
Arend van Spriel authored
The use of the function brcmf_proto_hdrpull() is moved to the common part of the driver and consequently it can be removed from the bus interface. Reviewed-by:
-
Arend van Spriel authored
The bus interface provided a wrapper function to pass a single packet to the common driver part filling a skb queue with one packet. For clarity the caller now sets up the skb queue and call the rx bus interface function. Reviewed-by:
-
Arend van Spriel authored
Several source files (but not all) define the pr_fmt() macro in exactly the same way. Instead this commit defines it in a header file so driver logging is consistent. Cc: Joe Perches <joe@perches.com> Reviewed-by:
-
Arend van Spriel authored
Upon unloading the brcmfmac module the USB firmware should be reset as the device remains powered. The reset assures a known device state when a new brcmfmac driver load is being done. Reviewed-by:
-
Hante Meuleman authored
Set bitrate_mask is not desired anymore. The firmware will determine the correct rates to be used. Reviewed-by:
-
Hante Meuleman authored
When USB device gets removed rx complete comes with 0-length packets. Do not refill those packets. In some rare cases it can cause infinite loop. Reviewed-by:
-
Piotr Haber authored
Dead code after AMPDU restructure. Reviewed-by:
Piotr Haber <phaber@broadcom.com> Signed-off-by:
-
Arend van Spriel authored
The interface address of the wireless device is determined by the permanent address stored in the device. This patch allows it to be overridden from user-space. Reported-by:
Maximilian Engelhardt <maxi@daemonizer.de> Reviewed-by:
-
Arend van Spriel authored
All callbacks that access driver functions should do that under perimeter lock protection. The add_interface() callback was lacking this lock. Reviewed-by:
-
Piotr Haber authored
On hardware reintialization reference count of already existing timers would be increased again. This leads to problems on module unloading. Reviewed-by:
-
Gabor Juhos authored
Both the rtt2x00usb_eeprom_read and the ioremap functions are allowed to fail, however their return values are not checked in the read_eeprom functions in the rt2800{pci,usb} drivers. The patch adds the missing checks, and converts all read_eeprom functions to return an int value, so the error values can be propagated up to the 'rt2800_validate_eeprom' function. Signed-off-by:Gabor Juhos <juhosg@openwrt.org> Signed-off-by:
-
Sujith Manoharan authored
Signed-off-by:
-
Geert Uytterhoeven authored
drivers/net/wireless/brcm80211/brcmsmac/main.c: In function ‘brcms_b_recv’: drivers/net/wireless/brcm80211/brcmsmac/main.c:7636: warning: ‘morepending’ may be used uninitialized in this function Signed-off-by:
Geert Uytterhoeven <geert@linux-m68k.org> Acked-by:
-
Stanislaw Gruszka authored
Power save support was removed from iwlegacy due to possible firmware crashes problems it cause. I use to plan first inspect code to find reason of problems, fix them and then allow to enable PS. But realistically - code inspection will not happen, so let's do it, and wait for eventual bug reports. Signed-off-by:
Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by:
-
Stanislaw Gruszka authored
Dump implementation of flush, which just wait until all TX queues become empty. Signed-off-by:
-
