Florian Fainelli says:

====================
Documentation: net: phy: Improve documentation

This patch series addresses discussions and feedback that was recently received
on the mailing-list in the area of: flow control/pause frames, interpretation of
phy_interface_t and finally add some links to useful standards documents.

Changes in v3:

- add Timur's feedback into patch 3

Changes in v2:

- clarify a few things in the RGMII section, add a paragraph about common issues
  with RGMII delay mismatches
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add links to the IEEE 802.3-2008 document, and the RGMII v1.3 and v2.0
revisions of the standard.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RGMII is a recurring source of pain for people with Gigabit Ethernet
hardware since it may require PHY driver and MAC driver level
configuration hints. Document what are the expectations from PHYLIB and
what options exist.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Describe that the Ethernet MAC controller is ultimately responsible for
dealing with proper pause frames/flow control advertisement and
enabling, and that it is therefore allowed to have it change
phydev->supported/advertising with SUPPORTED_Pause and
SUPPORTED_AsymPause.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove the function pointers documentation which duplicates information
found in include/linux/phy.h. Maintaining documentation about two
different locations just does not work, but the code is less likely to
be outdated.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mv88e6xxx_g1_irq_setup() sets up chip->g1_irq.nirqs interrupt mappings,
so free the same amount. This will be 8 or 9 in practice, less than 16.

Fixes: dc30c35b ("net: dsa: mv88e6xxx: Implement interrupt support.")
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
Mellanox 100G mlx5 DCBX and ethtool updates

This series provides the following mlx5 updates:

From Huy:
DCBX CEE API and DCBX firmware/host modes support.
    - 1st patch ensures the dcbnl_rtnl_ops is published only when the qos
      capability bits is on.
    - 2nd patch adds the support for CEE interfaces into mlx5 dcbnl_rtnl_ops
    - 3rd patch refactors ETS query to read ETS configuration directly from
      firmware rather than having a software shadow to it. The existing IEEE
      interfaces stays the same.
    - 4th patch adds the support for MLX5_REG_DCBX_PARAM and MLX5_REG_DCBX_APP
      firmware commands to manipulate mlx5 DCBX mode.
    - 5th patch adds the driver support for the new DCBX firmware.  This ensures
      the backward compatibility versus the old and new firmware. With the new DCBX
      firmware, qos settings can be controlled by either firmware or software
      depending on the DCBX mode.

From Kamal and Saeed:
    - mlx5 self-test support.

From Shaker:
    - Private flag to give the user the ability to enable/disable mlx5 CQE
      compression.

V1->V2:
    - Check ETS capability where needed in:
	("net/mlx5e: Read ETS settings directly from firmware")
    - Fix return value of mlx5e_dcbnl_switch_to_host_mode in:
	("net/mlx5e: ConnectX-4 firmware support for DCBX")
    - Update commit message of:
	("net/mlx5e: ConnectX-4 firmware support for DCBX")
    - Fix two sparse static check warnings in en_selftest.c

This series was generated against commit:
e5f12b3f ("Merge branch 'mlxsw-trap-groups-and-policers'")
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The user can now override the automatic driver decision using the
rx_cqe_compress flag, which is the preference for CQE compression.
The flag is initialized with the automatic driver decision.
Signed-off-by: Shaker Daibes <shakerd@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

pflags is a configuration parameter for the netdev, naturally it belongs
to priv->params.
Also introduce MLX5E_GET_PFLAG
Signed-off-by: Shaker Daibes <shakerd@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Extend the self diagnostic tests to support loopback test.

The loopback test doesn't require the offline flag, it will use the
generic dev_queue_xmit and a dedicated packet_type to capture and verify
mlx5e selftest loopback packets.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The self diagnostics test implementaion include the following features:
1. Link Test: Check that link is in up state.
2. Speed Test: Check that link was negotiated correctly.
3. Health Test: Check the device health.
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use setdcbx interface to set the DCBX mode to firmware or os.
If setdcbx is called with mode value of zero, the DCBX mode
is set to firmware.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

DBCX by default is controlled by firmware where dcbx capability bit
is set. In this mode, firmware is responsible for reading/sending the
TLV packets from/to the remote partner.

This patch sets up the infrastructure to move between HOST/FW DCBX
control mode.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add set/query commands for DCBX_PARAM register
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Issue description:
Current implementation saves the ETS settings from user in
a temporal soft copy and returns this settings when user
queries the ETS settings.

With the new DCBX firmware, the ETS settings can be changed
by firmware when the DCBX is in firmware controlled mode. Therefore,
user will obtain wrong values from the temporal soft copy.

Solution:
1. Read the ETS settings directly from firmware.
2. For tc_tsa:
   a. Initialize tc_tsa to vendor IEEE_8021QAZ_TSA_VENDOR at netdev
      creation.
   b. When reading ETS setting from FW, if the traffic class bandwidth
      is less than 100, set tc_tsa to IEEE_8021QAZ_TSA_ETS. This
      implementation solves the scenarios when the DCBX is in FW control
      and willing bit is on which means the ETS setting is dictated
      by remote switch.

Also check ETS capability where needed.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add DCBX CEE API interface for ConnectX-4. Configurations are stored in
a temporary structure and are applied to the card's firmware when
the CEE's setall callback function is called.

Note:
  priority group in CEE is equivalent to traffic class in ConnectX-4
  hardware spec.

  bw allocation per priority in CEE is not supported because ConnectX-4
  only supports bw allocation per traffic class.

  user priority in CEE does not have an equivalent term in ConnectX-4.
  Therefore, user priority to priority mapping in CEE is not supported.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make sure firmware supports qos before exposing the DCB API.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We use single queue even if multiqueue is enabled and let admin to
enable it through ethtool later. This is used to avoid possible
regression (small packet TCP stream transmission). But looks like an
overkill since:

- single queue user can disable multiqueue when launching qemu
- brings extra troubles for the management since it needs extra admin
  tool in guest to enable multiqueue
- multiqueue performs much better than single queue in most of the
  cases

So this patch enables multiqueue by default: if #queues is less than or
equal to #vcpu, enable as much as queue pairs; if #queues is greater
than #vcpu, enable #vcpu queue pairs.

Cc: Hannes Frederic Sowa <hannes@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Neil Horman <nhorman@redhat.com>
Cc: Jeremy Eder <jeder@redhat.com>
Cc: Marko Myllynen <myllynen@redhat.com>
Cc: Maxime Coquelin <maxime.coquelin@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Stefan Eichenberger says:

====================
Fix support for the MV88E6097

This patchset fixes the following two issues for the MV88E6097:
- Add missing definition of g1_irqs
- Add missing comment
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a missing comment for the MV88E6097 because of unification.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@netmodule.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the missing definition of g1_irqs for MV88E6097.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@netmodule.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
BPF cleanups and misc updates

This patch set adds couple of cleanups in first few patches,
exposes owner_prog_type for array maps as well as mlocked mem
for maps in fdinfo, allows for mount permissions in fs and
fixes various outstanding issues in selftests and samples.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

1) The test_lru_map and test_lru_dist fails building on my machine since
   the sys/resource.h header is not included.

2) test_verifier fails in one test case where we try to call an invalid
   function, since the verifier log output changed wrt printing function
   names.

3) Current selftest suite code relies on sysconf(_SC_NPROCESSORS_CONF) for
   retrieving the number of possible CPUs. This is broken at least in our
   scenario and really just doesn't work.

   glibc tries a number of things for retrieving _SC_NPROCESSORS_CONF.
   First it tries equivalent of /sys/devices/system/cpu/cpu[0-9]* | wc -l,
   if that fails, depending on the config, it either tries to count CPUs
   in /proc/cpuinfo, or returns the _SC_NPROCESSORS_ONLN value instead.
   If /proc/cpuinfo has some issue, it returns just 1 worst case. This
   oddity is nothing new [1], but semantics/behaviour seems to be settled.
   _SC_NPROCESSORS_ONLN will parse /sys/devices/system/cpu/online, if
   that fails it looks into /proc/stat for cpuX entries, and if also that
   fails for some reason, /proc/cpuinfo is consulted (and returning 1 if
   unlikely all breaks down).

   While that might match num_possible_cpus() from the kernel in some
   cases, it's really not guaranteed with CPU hotplugging, and can result
   in a buffer overflow since the array in user space could have too few
   number of slots, and on perpcu map lookup, the kernel will write beyond
   that memory of the value buffer.

   William Tu reported such mismatches:

     [...] The fact that sysconf(_SC_NPROCESSORS_CONF) != num_possible_cpu()
     happens when CPU hotadd is enabled. For example, in Fusion when
     setting vcpu.hotadd = "TRUE" or in KVM, setting ./qemu-system-x86_64
     -smp 2, maxcpus=4 ... the num_possible_cpu() will be 4 and sysconf()
     will be 2 [2]. [...]

   Documentation/cputopology.txt says /sys/devices/system/cpu/possible
   outputs cpu_possible_mask. That is the same as in num_possible_cpus(),
   so first step would be to fix the _SC_NPROCESSORS_CONF calls with our
   own implementation. Later, we could add support to bpf(2) for passing
   a mask via CPU_SET(3), for example, to just select a subset of CPUs.

   BPF samples code needs this fix as well (at least so that people stop
   copying this). Thus, define bpf_num_possible_cpus() once in selftests
   and import it from there for the sample code to avoid duplicating it.
   The remaining sysconf(_SC_NPROCESSORS_CONF) in samples are unrelated.

After all three issues are fixed, the test suite runs fine again:

  # make run_tests | grep self
  selftests: test_verifier [PASS]
  selftests: test_maps [PASS]
  selftests: test_lru_map [PASS]
  selftests: test_kmod.sh [PASS]

  [1] https://www.sourceware.org/ml/libc-alpha/2011-06/msg00079.html
  [2] https://www.mail-archive.com/netdev@vger.kernel.org/msg121183.html

Fixes: 3059303f ("samples/bpf: update tracex[23] examples to use per-cpu maps")
Fixes: 86af8b41 ("Add sample for adding simple drop program to link")
Fixes: df570f57 ("samples/bpf: unit test for BPF_MAP_TYPE_PERCPU_ARRAY")
Fixes: e1559671 ("samples/bpf: unit test for BPF_MAP_TYPE_PERCPU_HASH")
Fixes: ebb676da ("bpf: Print function name in addition to function id")
Fixes: 5db58faf ("bpf: Add tests for the LRU bpf_htab")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: William Tu <u9012063@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since we recently converted the BPF filesystem over to use mount_nodev(),
we now have the possibility to also hold mount options in sb's s_fs_info.
This work implements mount options support for specifying permissions on
the sb's inode, which will be used by tc when it manually needs to mount
the fs.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow for checking the owner_prog_type of a program array map. In some
cases bpf(2) can return -EINVAL /after/ the verifier passed and did all
the rewrites of the bpf program.

The reason that lets us fail at this late stage is that program array
maps are incompatible. Allow users to inspect this earlier after they
got the map fd through BPF_OBJ_GET command. tc will get support for this.

Also, display how much we charged the map with regards to RLIMIT_MEMLOCK.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit dcf80034 ("net/sched: act_mirred: Refactor detection whether
dev needs xmit at mac header") added dev_is_mac_header_xmit(); since it's
also useful elsewhere, move it to if_arp.h and reuse it for BPF.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

After setup we don't need to keep user space fd number around anymore, as
it also has no useful meaning for anyone, just remove it.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since long already bpf_func is not only about struct sk_buff * as
input anymore. Make it generic as void *, so that callers don't
need to cast for it each time they call BPF_PROG_RUN().
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

We don't use ->heap_buf after commit 46d1efd8 ("sfc: remove Software
TSO") so let's remove the last traces.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-next-for-davem-2016-11-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for 4.10

Major changes:

iwlwifi

* finalize and enable dynamic queue allocation
* use dev_coredumpmsg() to prevent locking the driver
* small fix to pass the AID to the FW
* use FW PS decisions with multi-queue

ath9k

* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
  latency and fix bufferbloat

wl18xx

* allow scanning in AP mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

sparse warns about context imbalance in any code
that uses HARD_TX_LOCK/UNLOCK - this is because it's
unable to determine that flags don't change so
lock and unlock are paired.

Seems easy enough to fix by adding __acquire/__release
calls.

With this patch af_packet.c is now sparse-clean,
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch depends on commit d8d26354 ("ptp: Introduce a high
resolution frequency adjustment method.")

The gianfar devices offer a frequency resolution of about 0.46 ppb
(depends on actual value of tmr_add, for the calculation assumed
0x80000000). This patch lets users of the device benefit from the increased
frequency resolution when tuning the clock. Thanks to the rounding the
maximum error between the requested frequency and the applied frequency
will then be about 0.23 ppb.

Tested on a v3.3.8 kernel on a real gianfar device. Verified compilation
on net-next (currently at v4.9-rc5).
Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Per RX ring packets/bytes counters are not protected by global
priv->stats_lock.

Better not confuse the reader, and use READ_ONCE() to show we read
these counters without surrounding synchronization.

Interrupt moderation is best effort, and we do not really care of
ultra precise counters.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

udplite conflict is resolved by taking what 'net-next' did
which removed the backlog receive method assignment, since
it is no longer necessary.

Two entries were added to the non-priv ethtool operations
switch statement, one in 'net' and one in 'net-next, so
simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull vfs splice fix from Al Viro.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fix default_file_splice_read()

Botched calculation of number of pages.  As the result,
we were dropping pieces when doing splice to pipe from
e.g. 9p.
Reported-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Pull i2c fixes from Wolfram Sang:
 "Here is a revert and two bugfixes for the I2C designware driver.

  Please note that we are still hunting down a regression for the
  i2c-octeon driver. While there is a fix pending, we have unclear
  feedback from the testers currently. An rc8 would be quite helpful
  for this case"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  Revert "i2c: designware: do not disable adapter after transfer"
  i2c: designware: fix rx fifo depth tracking
  i2c: designware: report short transfers

Pull ARM fix from Russell King:
 "This resolves the ksyms issues by reverting the commit which
  introduced the breakage"

There was what I consider to be a better fix, but it's late in the rc
game, so I'll take the revert.

* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
  Revert "arm: move exports to definitions"

Pull networking fixes from David Miller:

 1) Fix leak in fsl/fman driver, from Dan Carpenter.

 2) Call flow dissector initcall earlier than any networking driver can
    register and start to use it, from Eric Dumazet.

 3) Some dup header fixes from Geliang Tang.

 4) TIPC link monitoring compat fix from Jon Paul Maloy.

 5) Link changes require EEE re-negotiation in bcm_sf2 driver, from
    Florian Fainelli.

 6) Fix bogus handle ID passed into tfilter_notify_chain(), from Roman
    Mashak.

 7) Fix dump size calculation in rtnl_calcit(), from Zhang Shengju.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (26 commits)
  tipc: resolve connection flow control compatibility problem
  mvpp2: use correct size for memset
  net/mlx5: drop duplicate header delay.h
  net: ieee802154: drop duplicate header delay.h
  ibmvnic: drop duplicate header seq_file.h
  fsl/fman: fix a leak in tgec_free()
  net: ethtool: don't require CAP_NET_ADMIN for ETHTOOL_GLINKSETTINGS
  tipc: improve sanity check for received domain records
  tipc: fix compatibility bug in link monitoring
  net: ethernet: mvneta: Remove IFF_UNICAST_FLT which is not implemented
  dwc_eth_qos: drop duplicate headers
  net sched filters: fix filter handle ID in tfilter_notify_chain()
  net: dsa: bcm_sf2: Ensure we re-negotiate EEE during after link change
  bnxt: do not busy-poll when link is down
  udplite: call proper backlog handlers
  ipv6: bump genid when the IFA_F_TENTATIVE flag is clear
  net/mlx4_en: Free netdev resources under state lock
  net: revert "net: l2tp: Treat NET_XMIT_CN as success in l2tp_eth_dev_xmit"
  rtnetlink: fix the wrong minimal dump size getting from rtnl_calcit()
  bnxt_en: Fix a VXLAN vs GENEVE issue
  ...

Pull libnvdimm fixes from Dan Williams:

 - Fix a crash that occurs at driver initialization if the memory region
   is already busy (request_mem_region() fails).

 - Fix a vma validation check that mistakenly allows a private device-
   dax mapping to be established. Device-dax explicitly forbids private
   mappings so it can guarantee a given fault granularity and backing
   memory type.

 Both of these fixes have soaked in -next and are tagged for -stable.

* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  device-dax: fail all private mapping attempts
  device-dax: check devm_nsio_enable() return value