Fix the "attempting to setting" message in ohci1394.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Remove the unneeded code that clears, sets and again clears the
rcvPhyPkt bit in the ohci1394 LinkControl register in ohci_initialize().
Signed-off-by: Bernhard Kauer <kauer@os.inf.tu-dresden.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

If posted write failed, an "Unhandled interrupt(s) 0x00000100" message
was logged by mistake.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

eth1394 did not work on buses consisting of S100B...S400B hardware
because it attempted to send GASP packets at S800.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

This patch fixes some error handlings in eth1394:

- check return value of kmem_cache_create()
- cleanup resources if hpsb_register_protocol() fails
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (whitespace)

This patch actually doesn't change anything because there was always 0
== NETDEV_TX_OK returned before.

TODO: Return NETDEV_TX_BUSY in error case and test in different error
conditions.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

offset > fi->offset + fi->len - 1  ==  !(offset < fi->offset + fi->len)
offset + len - 1 < fi->offset      ==  !(offset + len > fi->offset)
!(A || B)  ==  (!A && !B)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

We can't reconfigure the MAC address, hence we don't need the callback.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

because CONFIG_IEEE1394_ETH1394 depends on it.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

RFC 2734 says: "IP-capable nodes may operate with an MTU size larger
than the default [1500 octets], but the means by which a larger MTU is
configured are beyond the scope of this document."

Allow users to set an MTU bigger than 1500.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

highlevel_host_reset no longer has any modular users.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Call only eth1394's own host reset handler from .tx_timeout, not the
reset hooks of all other IEEE 1394 drivers.

A minor drawback of this patch is that ether1394_host_reset by timeout
is not serialized against ether1394_host_reset by bus reset.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

The old argument calculated the correct value in a wrong way.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Move common code into an extra function.  This implicitly adds a missing
node_info->fifo = CSR1212_INVALID_ADDR_SPACE; to .update.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Adjust white space and line wraps.  Remove unnecessary parentheses and
braces, unused macros, and some of the more redundant comments.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

There is some common code between ether1394_open and ether1394_add_host
which can be moved to a separate helper function for a slightly smaller
eth1394 driver (-160 bytes on i386.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Until now, ieee1394 put an IP-over-1394 capability entry into each new
host's config ROM.  As soon as the controller was initialized --- i.e.
right after modprobe ohci1394 --- this entry triggered a hotplug event
which typically caused auto-loading of eth1394.

This irritated or annoyed many users and distributors.  Of course they
could blacklist eth1394, but then ieee1394 wrongly advertized IP-over-
1394 capability to the FireWire bus.

Therefore
  - remove the offending kernel config option
    IEEE1394_CONFIG_ROM_IP1394,
  - let eth1394 add the ROM entry by itself, i.e. only after eth1394 was
    loaded.

This fixes http://bugzilla.kernel.org/show_bug.cgi?id=7793 .

To emulate the behaviour of older kernels, simply add the following to
to /etc/modprobe.conf:

install ohci1394 /sbin/modprobe eth1394; \
                 /sbin/modprobe --ignore-install ohci1394

Note, autoloading of eth1394 when an _external_ IP-over-1394 capable
device is discovered is _not_ affected by this patch.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Shrinks eth1394.ko by about 5%.

Many of these functions have only one caller and are therefore auto-
inlined anyway.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

ether1394_add_host() guarantees that hi->dev != NULL if hi != NULL.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Warn if hpsb_allocate_and_register_addrspace() failed.
Unregister the address space if something else failed.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

The comment says it all.  This affects only asynchronous streams sent
via raw1394; the eth1394 driver has own code and needs an own fix.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

SPIN_LOCK_UNLOCKED cleanup,use DEFINE_SPINLOCK instead
Signed-off-by: Milind Arun Choudhary <milindchoudhary@gmail.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Shrinks object file size a little bit.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Everytime when eth1394 or a libraw1394 client updates the configuration
ROM, a certain sysfs attribute cannot be added since it already exists.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

This is a coding style touch-up for ieee1394's handle_incoming_packet().

A preprocessor macro contained hardwired variable names and, even worse,
the 'break' keyword.  This macro is now unrolled and removed.

Also, all 'break's which had the effect of a return are replaced by
return.  And a FIXME comment is brought up to date.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

alpha:

drivers/ieee1394/iso.c: In function 'hpsb_iso_xmit_sync':
drivers/ieee1394/iso.c:440: error: invalid use of undefined type 'struct task_struct'
drivers/ieee1394/iso.c:440: error: 'TASK_INTERRUPTIBLE' undeclared (first use in this function)
drivers/ieee1394/iso.c:440: error: (Each undeclared identifier is reported only once
drivers/ieee1394/iso.c:440: error: for each function it appears in.)
drivers/ieee1394/iso.c:440: warning: implicit declaration of function 'signal_pending'
drivers/ieee1394/iso.c:440: error: invalid use of undefined type 'struct task_struct'
drivers/ieee1394/iso.c:440: warning: implicit declaration of function 'schedule'
drivers/ieee1394/iso.c: In function 'hpsb_iso_wake':
drivers/ieee1394/iso.c:562: error: 'TASK_INTERRUPTIBLE' undeclared (first use in this function)
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (brought into alphabetic order)

Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

drivers/ieee1394/ieee1394_transactions.c fails for me if CONFIG_SMP=n

gcc complains:
  CC      drivers/ieee1394/ieee1394_transactions.o
drivers/ieee1394/ieee1394_transactions.c: In function 'hpsb_get_tlabel':
drivers/ieee1394/ieee1394_transactions.c:183: error:
'TASK_INTERRUPTIBLE' undeclared (first use in this function)
drivers/ieee1394/ieee1394_transactions.c:183: error: (Each undeclared
identifier is reported only once
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (added comment)

Fix printk format string:
drivers/ieee1394/ieee1394_core.c:702: warning: format '%d' expects type 'int', but argument 2 has type 'size_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

This considerably reduces the memory requirements for a packet and
eliminates ieee1394's dependency on CONFIG_NET.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

This will point out firmware bugs.

I tested with 11 SBP-2 devices and one OS X PC and got these errors from
two old CD-RWs only.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Code beneath two labels called "fail" is actually also reached in case
of success.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

We want bugs to show themselves.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Make unnecessarily generic code specific and thus simpler.
Shrink a lookup table from 128 to 16 bytes.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>

Whitespace, line breaks, braces...
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>