With working GPIO, during init the GPIO state s reset.
This causes the sdmmc regulator to shut down, preventing detection.
Removing and replacing the card will allow it to be detected, but that should not be necessary.
Fix this by setting the regulator on at boot.
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Link: https://lore.kernel.org/r/20191016185945.1962-1-pgwipeout@gmail.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

For rk3399-roc-pc is a mezzanine board available that carries M.2 and
POE interfaces. Use it with a separate dts.
Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/0fb4e21a-fe78-00aa-6142-ca8682a913eb@fivetechno.deSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Beelink A1 is a TV box implementing the higher-end options of the
RK3328 reference design - the DTB from the stock Android firmware is
clearly the "rk3328-box-plus" variant from the Rockchip 3.10 BSP with
minor modifications to accommodate the USB WiFi module and additional
VFD-style LED driver. It features:

- 4GB of 32-bit LPDDR3
- 16GB of HS200 eMMC (newer models with 32GB also exist)
- Realtek RTL8211F phy for gigabit ethernet
- Fn-Link 6221E-UUC module (RealTek RTL8821CU) for 11ac WiFi
  and Bluetooth 4.2
- HDMI and analog A/V
- 1x USB 3.0 type A host, 1x USB 2.0 type A OTG, 1x micro SD
- IR receiver and a neat little LED clock display.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/2aa21c5f3020062cf6a47057bdf3c01f0ec863ea.1571090991.git.robin.murphy@arm.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add a binding for the RK3328-based Beelink A1 TV box.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/82324d17b770fa8ea189fa708490d2c8c0c9290e.1571090991.git.robin.murphy@arm.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

The audio pipelines for HDMI and the analog codec are internal to the
SoC, so it makes sense to describe them at that level such that boards
need only enable the respective nodes for outputs they implement.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/a09c8d795e7a66fb7bc47af2b6580f6e8dbec91e.1571090991.git.robin.murphy@arm.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

ROC-RK3308-CC is a rk3308 based board designed by Firelfy,
with eMMC and 256MB DDR3 and RTL8188 Wifi on board.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Link: https://lore.kernel.org/r/20191030072811.29882-1-andy.yan@rock-chips.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add compatible for Firefly ROC-RK3308-CC board.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Link: https://lore.kernel.org/r/20191030072648.29738-1-andy.yan@rock-chips.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Fixup some typos and inconsistencies in the grf binding.
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Link: https://lore.kernel.org/r/20191028182254.30739-3-pgwipeout@gmail.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Correct the voltage supplies according to the board schematics
ROC-3399-PC-V10-A-20180804.
Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
Link: https://lore.kernel.org/r/22b56700-3c9e-0f60-cd74-7ff24d4f1a23@fivetechno.deSigned-off-by: Heiko Stuebner <heiko@sntech.de>

rk3399-roc-pc has vcc_sys 5V supply for USB and other peripherals.
Add the GPIO pin to enable the regulator.
Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
Link: https://lore.kernel.org/r/c72db0ad-c261-af4f-efe6-22bbcf4a0b7b@fivetechno.deSigned-off-by: Heiko Stuebner <heiko@sntech.de>

rk3399-roc-pc has a power and a recovery button, enable them.
Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
Link: https://lore.kernel.org/r/1ce152cc-bd6b-63af-7892-221e084d087f@fivetechno.deSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Enable the phy node ion the px30 evb board.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20190917082659.25549-13-heiko@sntech.de

Add the usb2phy node on the px30 and hook it up to the usb controllers
it supplies.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20190917082659.25549-12-heiko@sntech.de

Having a default optee node in a soc devicetree is not really good.
For one there is no guarantee that any tee got loaded and there's even
the possibility that a completely different TEE got loaded.

OP-Tee however will insert relevant nodes to the devicetree (firmware
+reserved memory sections) during its own startup, so there really is
no need to provide a default node.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20191023224409.3550-1-heiko@sntech.de

Set the supplying regulator and enable the gpu node on the rk3399-puma som.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20191023223954.3139-1-heiko@sntech.de

The px30 soc contains a controller for one-time-programmable memory,
so add the necessary node for it and the fields defined in it by default.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20191023224113.3268-1-heiko@sntech.de

rk3399-roc-pc has three gpio LEDs, enable them.
Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
Link: https://lore.kernel.org/r/7d8d85c9-5fde-7943-a6b6-639bca38bdc1@fivetechno.deSigned-off-by: Heiko Stuebner <heiko@sntech.de>

This board use uart4 as debug port and arm core voltage
is modulated by pwm, logic voltage is fixed to 1.05V.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Link: https://lore.kernel.org/r/20191021084657.28629-1-andy.yan@rock-chips.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Add compatible for RK3308 Evaluation board
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20191021084642.28562-1-andy.yan@rock-chips.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

RK3308 is a quad Cortex A35 based SOC with rich audio
interfaces(I2S/PCM/TDM/PDM/SPDIF/VAD/HDMI ARC), which
designed for intelligent voice interaction and audio
input/output processing.

This patch add basic core dtsi file for it.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Link: https://lore.kernel.org/r/20191021084616.28431-1-andy.yan@rock-chips.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

RK3308 GRF is divided into four sections: GRF, SGRF,
DETECTGRF, COREGRF. This patch add documentation for
it.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20191021084555.28356-1-andy.yan@rock-chips.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

The defines RK_FUNC_1, RK_FUNC_2, RK_FUNC_3 and RK_FUNC_4
are no longer used. Mark them as "deprecated"
to prevent that someone start using them again.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20191015205852.4200-2-jbx6244@gmail.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

The define RK_FUNC_1 is no longer used,
so restyle the rockchip,pins definitions.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20191015205852.4200-1-jbx6244@gmail.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Use the now-preferred generic phy reset properties instead of the
dwmac-specific ones.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/4d16c24ae3651a2119cf5bb1213f46a9fce4b39a.1570444773.git.robin.murphy@arm.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

All the nanopi4 boards have HDMI, so let them make noise on it.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/7fe6e94e4b9f5986f19f2637b7b716f0cb54de1b.1570444701.git.robin.murphy@arm.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

Scarlet and Bob use the Google-developed cr50 chip to do things
like TPM and closed-case-debugging.

Add the nodes describing the cr50 and its spi-connection.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20180822120925.12388-1-heiko@sntech.de

This patch adds audio codec (Everest ES8316) and I2S audio nodes for
RK3399 RockPro64.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Link: https://lore.kernel.org/r/20190907174833.19957-1-katsuhiro@katsuster.netSigned-off-by: Heiko Stuebner <heiko@sntech.de>

The rk3399 gic-its was missing the #msi-cells property as found by
dt-schema checks, so add it.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20190917083625.25818-1-heiko@sntech.de

Few, know rk808 pmic regulators VCC[1-4], VCC[6-7], VCC[9-11],
VDD_LOG, VDD_GPU, VDD_CPU_B, VCC3V3_SYS are inputting with vcc_sys
which is 5V power rail from dc_12v.

So, replace the vin-supply of above mentioned regulators
with vcc_sys as per the PMIC-RK808-D page of roc-rk3399-pc
schematics.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20190919052822.10403-7-jagan@amarulasolutions.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

It is always better practice to follow regulator naming conventions
as per the schematics for future references.

This would indeed helpful to review and check the naming convention
directly on schematics, both for the code reviewers and the developers.

So, rename vcc12v_sys into dc_12v as per rk3399 power tree as per
roc-rk3399-pc schematics.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://lore.kernel.org/r/20190919052822.10403-6-jagan@amarulasolutions.comSigned-off-by: Heiko Stuebner <heiko@sntech.de>

One of the separate General Register Files contains the registers for
controlling the usb2phy, so add the necessary binding compatible for it.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20190917082659.25549-11-heiko@sntech.de

Enable i2c1 and adds the devices connected to it.
This includes a magnetometer, goodix-touchscreen and accelerometer.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20190917082659.25549-10-heiko@sntech.de

The px30 contains 2 separate clock controllers the regular cru creating
most clocks as well as the pmucru managing the GPLL and some other clocks.

The gpll of course also is needed by the cru, so while we normally do rely
on clock names to associate clocks getting probed later on (for example
xin32k coming from an i2c device in most cases) it is safer to declare the
explicit dependency between the two crus. This makes sure that for example
the clock-framework probes them in the correct order from the start.

The assigned-clocks properties were simply working by chance in the past
so split them accordingly to the 2 crus to honor the loading direction.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20190917082659.25549-9-heiko@sntech.de

These are unused gpio-settings for specific function pins, that
are not used by anything and only clutter up the dtsi.
They can be re-added when a relevant user is added.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20190917082659.25549-8-heiko@sntech.de

The px30-evb exposes uart2 through a uart-to-usb converter on the board
but these pins are shared with the sdmmc controller. With both activated
this results in a race condition depending in the probe order.
Whichever of the two probes first will break the other peripheral.

The px30-evb also exposes uart5 through pin its pin headers, so it's way
saner to use these pins for serial output and keep the sdmmc working in
all cases.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20190917082659.25549-7-heiko@sntech.de

Hook the reset line into an emmc-pwrseq for it to get initialized nicely.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20190917082659.25549-6-heiko@sntech.de

Add the board's pmic (rk809) and hook up the real supplies to their
consumers. This is especially important as cpufreq would otherwise hang
the system when scaling the frequency without adjusting the voltage.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20190917082659.25549-5-heiko@sntech.de

emmc chips are normally hooked up in standard ways using the full 8bit
bus connection, so there should be no need for all future boards to define
this on their own. So add default pin setups for 8bit busses and special
boards really only needing 4 or 1 bit connections can override.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20190917082659.25549-4-heiko@sntech.de

That gpio1-b0 can only be flash_cs apart from a regular gpio,
so there is no power-related pinmux for the emmc for this pin.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20190917082659.25549-3-heiko@sntech.de

Similar to all other Rockchip SoCs the px30 does not have a static
32kHz clock. Instead it again gets supplied from an external component
like the pmic.

So drop the static clock, so that we can hook up the right one.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20190917082659.25549-2-heiko@sntech.de