To reconfigure clocks, controlled by FRQCRA and FRQCRB, a kick bit has to
be set and to make sure the setting has taken effect, it has to be read
back repeatedly until it is cleared by the hardware. This patch adds the
waiting part, that was missing until now.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a platform device for the r8a73a4 PFC.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add IRQC interrupt controller support to r8a73a4 by
hooking up two IRQC instances to handle 58 external
IRQ signals. There IRQC controllers are tied to SPIs
of the GIC. On r8a73a4 exact IRQ pin routing is handled
by the PFC which is excluded from this patch.

Both platform devices and DT devices are added in this
patch. The platform device versions are used to provide
a static interrupt map configuration for board code
written in C.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

V3 of SCIF serial port support for the r8a73a4 SoC.
This is done by adding platform devices for SCIFA0
-> SCIFA1 as well as SCIFB0 -> SCIFB3 together with
clock bindings. DT device description is excluded at
this point since such bindings are still under
development.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

V3 of initial support for the r8a73a4 SoC including:
 - Single Cortex-A15 CPU Core
 - GIC
 - Architecture timer

No static virtual mappings are used, all the components
make use of ioremap(). DT_MACHINE_START is still wrapped
in CONFIG_USE_OF to match other mach-shmobile code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Update for Renesas INTC External IRQ pin driver for v3.10

This adds support for shared interrupt lines to the
Renesas INTC External IRQ pin driver which has already
been queued up for v3.10 (tag renesas-intc-external-irq-for-v3.10).

The patch "irqchip: intc-irqpin: Add support for shared interrupt lines"
in renesas-intc-external-irq2-for-v3.10 is a dependency for
"ARM: shmobile: r8a7740: Migrate from INTC to GIC". That dependency is
the reason for this merge.

On some hardware we don't have a 1-1 mapping from the external
interrupts coming from INTC to the GIC SPI pins. We can however
share lines to demux incoming IRQs on these SoCs.

This patch enables the intc_irqpin driver to detect requests for shared
interrupt lines and demuxes them properly by querying the INTC INTREQx0A
registers.

If you need multiple shared intc_irqpin device instances, be sure to mask
out all interrupts on the INTC that share the one line before you start
to register them. Else you run into IRQ floods that would be caused by
interrupts for which no handler has been set up yet when the first
intc_irqpin device is registered.
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add DT support to the IRQC External IRQ Pin driver.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add initial DT support to the INTC External IRQ Pin
driver. At this point only hardware with 4-bit wide
sense registers is supported via DT.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The platform data for the INTC irq pin driver
seems to be global symbols, make it static to
allow multi-soc build.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The platform data for the INTC irq pin driver
seems to be global symbols, make it static to
allow multi-soc build.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch adds a driver for external IRQ pins connected
to the IRQC hardware block on recent SoCs from Renesas.

The IRQC hardware block is used together with more
recent ARM based SoCs using the GIC. As usual the GIC
requires external IRQ trigger setup somewhere else
which in this particular case happens to be IRQC.

This driver implements the glue code needed to configure
IRQ trigger and also handle mask/unmask and demux of
external IRQ pins hooked up from the IRQC to the GIC.

Tested on r8a73a4 but is designed to work with a wide
range of SoCs. The driver requires one GIC SPI per
external IRQ pin to operate.  Each driver instance
will handle up to 32 external IRQ pins.

The SoCs using this driver are currently mainly used
together with regular platform devices so this driver
allows configuration via platform data to support things
like static interrupt base address. DT support will
be added incrementally in the not so distant future.
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add GPL header to platform data include file.
Signed-off-by: Magnus Damm <damm@opensource.se>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Use devm_kzalloc(), devm_ioremap_nocache()
and devm_request_irq() to simplify error
handling.
Signed-off-by: Magnus Damm <damm@opensource.se>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add comments to describe the special case for
"force" versions of enable and disable functions.
Signed-off-by: Magnus Damm <damm@opensource.se>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Cache IRQ in domain_irq variable instead of
making use of irq_find_mapping(). While at it
rename the irq variable to requested_irq.
Signed-off-by: Magnus Damm <damm@opensource.se>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Remove whitespace damage and add newline
between variables and code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Update the r8a7779 IRQ code to make use of the
INTC External IRQ pin driver for external
interrupt pins IRQ0 -> IRQ3.

The r8a7779 SoC can like older SH SoCs configure
to use the IRQ0 -> IRQ3 signals as individual
interrupts or a combined IRL mode.

Without this patch the r8a7779 SoC code does
not fully support external IRQ pins in individual
IRQ mode. The r8a7779 PFC code does not yet have
gpio_to_irq() support so no need to update such
code.

At this point the DT reference implementations
are not covered. In the future such code shall
tie in the INTC External IRQ pin driver via
DT, so this kind of verbose code is not needed
for the long term DT case.
Signed-off-by: Magnus Damm <damm@opensource.se>
Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Adjust the sh73a0 IRQ code to make use of the
INTC External IRQ pin driver for external
interrupt pins IRQ0 -> IRQ31.

This removes quite a bit of special-case code
in intc-sh73a0.c but the number of lines get
replaced with platform device information in
setup-sh73a0.c. The PFC code is also adjusted
to make gpio_to_irq() return the correct
interrupt number.

At this point the DT reference implementations
are not covered. In the future such code shall
tie in the INTC External IRQ pin driver via
DT, so this kind of verbose code is not needed
for the long term DT case.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the macro irq_pin() to let board-specific code using
platform devices tie in external IRQn pins in a common way.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This patch adds a driver for external IRQ pins connected
to the INTC block on recent SoCs from Renesas.

The INTC hardware block usually contains a rather wide
range of features ranging from external IRQ pin handling
to legacy interrupt controller support. On older SoCs
the INTC is used as a general purpose interrupt controller
both for external IRQ pins and on-chip devices.

On more recent ARM based SoCs with Cortex-A9 the main
interrupt controller is the GIC, but IRQ trigger setup
still need to happen in the INTC hardware block.

This driver implements the glue code needed to configure
IRQ trigger and also handle mask/unmask and demux of
external IRQ pins hooked up from the INTC to the GIC.

Tested on sh73a0 and r8a7779. The hardware varies quite
a bit with SoC model, for instance register width and
bitfield widths vary wildly. The driver requires one GIC
SPI per external IRQ pin to operate.  Each driver instance
will handle up to 8 external IRQ pins.

The SoCs using this driver are currently mainly used
together with regular platform devices so this driver
allows configuration via platform data to support things
like static interrupt base address. DT support will
be added incrementally in the not so distant future.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
[Rename device from to rcarfb to rcar-du]
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[Manual conflict resolution]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Commit "ARM: shmobile: r8a7779: use gic_iid macro" switched R8A7779 platform
devices to using gic_iid() macro instead of gic_spi() but commit "ARM: mach-
shmobile: r8a7779: add SATA support" added another use of gic_spi(). Convert
the SATA IRQ resource to using gic_iid().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add SATA clock for r8a7779 SoC (for both device tree and usual cases).
Register SATA controller as a "late" platform device on r8a7779 SoC.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Allow configuration of the r8a7779 SoC SATA controller using a flattened device
tree.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

76cc1887
(thermal: rcar: add Device Tree support)
supported rcar_thermal DT probing.

rcar thermal driver doesn't support IRQ on r8a7779 chip
since it is using old design IRQ.
R-Car/R-Mobile next generation chips are using new design IRQ,
and rcar thermal driver is supporting these.

This patch adds rcar_thermal DT support for r8a7779 without IRQ.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

move r8a7740_meram_workaround() to r8a7740 area
from r8a7779 area
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

"ARM: shmobile: add gic_iid macro for ICCIAR / interrupt ID"
enabled to use gic_iid macro.
This patch exchange current GIC interrupt setting
from gic_spi() to gic_iid()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
[ horms+renesas@verge.net.au: Updated git commit id in changelog ]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

r8a7779 is not sh73a0
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

r8a7779 is not r8a7740 chip
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

R-Car H1 datasheet GIC number is indicating
GIC ICCIAR / interrupt ID number, not SPI number,
but current marzen board code is using gic_spi() with
un-understandable calculation.

This patch adds new gic_iid() macro which means
ICCIAR / interrupt ID, and used the number
currently written on datasheet.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
[ horms+renesas@verge.net.au: Split board-marzen.c portion into a separate patch ]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This adds temporarily the alternative device names to the clock list
that are used when booting via Device Tree setup.
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Each CPU Hotplug implementation for mach-shmobile
is now self-contained, so this change removes unused
helper code in hotplug.c. The two CPU Hotplug capable
SoCs sh73a0 and r8a7779 remain unchanged.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Update the r8a7779 SMP code and CPU Hotplug in particular
to follow the same style as sh73a0. This means dropping
__maybe_unused for #ifdef CONFIG_HOTPLUG_CPU.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Convert the sh73a0 CPU Hotplug code to use a local
implementation of ->cpu_disable(). With this change
in place the sh73a0 SMP code does no longer depend
on hotplug.c.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Update the SMP code for R8A7779 to make use of the
shared SCU function scu_power_mode() together with
the early setup code in shmobile_secondary_vector_scu.

With this patch in place the secondary CPUs modify the
SCU setting during early boot instead of letting other
CPUs deal with the coherency setting before boot. In
other words, we used to setup coherency before boot
in r8a7779_boot_secondary() but that bit is now instead
handled by the code in shmobile_secondary_vector_scu.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Update the r8a7779 CPU Hotplug code to use SCU PSR
to wait for the target CPU core. Previously the
shared code in hotplug.c was used to let cpu_kill()
wait for cpu_die(). With this change in place the
r8a7779 SMP code does not depend on hotplug.c anymore.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Rework the IOMEM() usage for the SCU base address in the
case of r8a7779. Adjusts the TWD to use R8A7779_SCU_BASE.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Rework the IOMEM() usage for the SCU base address in the
case of sh73a0. Removes recently introduced build warnings:

arch/arm/mach-shmobile/smp-sh73a0.c:45:15: warning: initialization makes integer from pointer without a cast [enabled by default]
arch/arm/mach-shmobile/smp-sh73a0.c:45:15: warning: (near initialization for 'twd_local_timer.res[0].start') [enabled by default]
arch/arm/mach-shmobile/smp-sh73a0.c:45:15: warning: initialization makes integer from pointer without a cast [enabled by default]
/arch/arm/mach-shmobile/smp-sh73a0.c:45:15: warning: (near initialization for 'twd_local_timer.res[0].end') [enabled by default]
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Rework the early SCU setup code in headsmp-scu.S to read
the base address in the same way as we use to fetch the
address of the invalidation function.
Reported-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>