The bit of sdio interrupt is 16 in designware implementation,
but it is 24 on Rockchip SoCs.This patch add sdio_id0 for the
number of slot0 in the SDIO interrupt registers.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In order to use the mvsdio driver for sdio, it has been necessary to
use a module parameter to disable DMA so to force PIO is used. It is
then possible to use wireless LAN devices like mwifiex found on
topkick and mirabox. However, accessing an MMC SD card does work with
DMA.

Investigation has shown that MMC block device accesses are always
aligned to 64 byte boundaries, where as transfers from mwifiex are
rarely more than word aligned. It has also been determined that card
to host transfers work with DMA for SDIO devices, but host to card
transfers with DMA have problems.

This patch extends the current checks for buffers which are not word
aligned or multiple of words. All host to card transfers which are not
64 byte aligned are now also performed via PIO. This should not affect
the performance of SD cards, but allow sdio devices to work out of the
box, and they are likely to be more efficient since DMA will be used
for card to host transfers.

Tested on mirabox for wifi via mwifiex
Tested on 370 RD for file systems on an SD card.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Currently the driver imposes a limit of 256 total minor numbers,
apparently based on the historic Unix/Linux limit.  This is quite
restrictive, particularly if we raise the maximum number of
partitions per card to 256 to match sd.

In order to make the full minor number space available we would
have to replace the static dev_use and name_use arrays with struct
ida.  But we can at least allow use of 256 cards rather than just
256 minors, with only a small change.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

There are upcoming ARM64 SoCs with dw_mmc host controller.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc_sdio_power_restore() calls
	mmc_send_if_cond(host, host->card->ocr);

	ret = mmc_send_io_op_cond(host, 0, NULL);

between mmc_go_idle() and mmc_sdio_init_card().
mmc_sdio_resume() needs to as well, else my libertas sdio wifi
device doesn't resume properly from suspend.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

As we are restoring power to a known card, it makes sense to use
the 'ocr' value known for the card rather than the generic one
for the host interface.
This matches the use of card->ocr passed to mmc_power_up in
mmc_sdio_runtime_resume  (just before mmc_sdio_power_restore is
called), and the value passed to mmc_sdio_init_card() a little
later in mmc_sdio_power_restore().
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This patch resurrects an old never-finished driver for Toshiba PCI SD
controllers found in some older Toshiba laptops (such as Portege R100):

02:0d.0 System peripheral [0880]: Toshiba America Info Systems SD TypA Controller [1179:0805] (rev 05)

The code is fixed, cleaned up and successfully tested with SD, SDHC, SDXC and
MMC cards on Portege R100. (MMC cards don't even work in Windows!)
SDIO probably does not work (don't have any SDIO card).

The hardware is slow (around 2 MB/s - same in Windows) because it does not
support bus mastering (busmaster enable bit cannot be set in PCI control reg).
Also the card clock is limited to 16MHz (33MHz PCI clock divided by 2).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The Exynos7 has a DWMMC controller (v2.70a) which is different from
prior versions. This patch adds new compatible strings for exynos7.
This patch also fixes the CLKSEL register offset on exynos7.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Tested-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

mmc_do_hw_reset(), mmc_power_up() and mmc_power_off() all set similar
initial values for bus_mode, bus_width, chip_select and timing. Let's
make this handling simpler and more consistent by sticking them
together in a common function. This will introduce small changes in
behavior in the following places:

mmc_power_off():

  For SPI hosts, explicitly set bus_mode = MMC_BUSMODE_PUSHPULL and
  chip_select = MMC_CS_HIGH, before we left them as they were.

  For non-SPI hosts, set bus_mode = MMC_BUSMODE_PUSHPULL instead of
  MMC_BUSMODE_OPENDRAIN as before.

  These two changes should not be a problem since the device will be
  powered off anyway.

mmc_do_hw_reset():

  Always set bus_mode = MMC_BUSMODE_PUSHPULL, as required by SD/SDIO
  cards. MMC cards require MMC_BUSMODE_OPENDRAIN, but this is taken
  care of by mmc_init_card() and mmc_attach_mmc().
Signed-off-by: Johan Rudholm <johanru@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

omap_hsmmc only supports one slot. So slot id is always zero, and
slot id was never used in the callbacks anyway
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

These callbacks are set during driver probe and not from the platform
init, -- evtl. they had been for oamp 1/2 -- for omap3 they are local
functions of the driver. These indirection could be dropped
altogether in favor of regular function calls TODO
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

this is needed when installing callbacks in the host struct and not
in the platform data, e.g. cover detect irq should be stored in
omap_hsmmc_host and not platform data
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

omap_hsmmc supports only one slot per controller, see OMAP_MMC_MAX_SLOTS.
This unnecessary indirection leads to confusion in the omap_hsmmc driver.
For example the card_detect callback is not installed by platform code
but from the driver probe function. So it should be a field of
omap_hsmmc_host. But since it is declared under the platform slot while
the drivers struct omap_hsmmc_host has no slot abstraction, this looks
like a bug, especially when not familiar that this driver only supports
1 slot anyway.
Either we should add a slot abstraction to omap_hsmmc_host or remove
it from the platform data struct. Removed since slot multiplexing is
an un-implemented feature
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

trigger of this callback has been removed in 0a82e06eAcked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

these fields are never read, probably an unimplemented feature
or superseded by pm_runtime
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

these callbacks are not set, probably legacy omap 1/2 features
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

platform data is built from omap2_hsmmc_info, remove all fields that
are never set in omap_hsmmc_info, hence never copied to platform data.
Note that the omap_hsmmc driver is not affected by this patch those
fields were completely unused.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

- omap mmc driver supports multiplexing, omap_mmc_hs doesn't
this leads to one of the major confusions in the omap_hsmmc driver

- platform data should be read-only for the driver
most callbacks are not set by the omap3 platform init code while still
required. So they are set from the driver probe function, which is against
the paradigm that platform-data should not be modified by the driver
typical examples are card_detect, read_only callbacks

un-bundling by searching for driver name \"omap_hsmmc in the
arch/arm folder. omap_hsmmc_platform_data is not initialized directly,
but from omap2_hsmmc_info, which is defined in a separate header file
not touched by this patch

hwmod includes platform headers to declare features of the platform. All
the declared features are prefixed OMAP_HSMMC. There is no need to
include platform header from hwmod other except for feature defines
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Only a few files really need that platform header. When later splitting
omap_mmc_platform_data into omap_mmc and omap_mmc_hs, those files
declaring an hs mmc platform data will have to change the platform
include, which is a good sanity check.
Also removing omap242x_init_mmc, which is not used anywhere, checked
with grep.
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Amend the atmel mci pin controller to optionally take a pin control
handle and set the state of the pins to:
- "default" on boot, resume and before performing an transfer.
- "sleep" on suspend().

This should make it possible to optimize energy usage for the pins
both for the suspend/resume cycle.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

MMC core already has support for HS400.  Add HS400
support to SDHCI driver.  The SDHC Standard specification
does not define HS400 so consequently HS400 support is
non-standard.  However HS400 is not selected without
the host controller setting the corresponding capability
flags so host controllers not yet supporting HS400
will not be affected.  To support that, a quirk
SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400 is introduced to
enable the use of capabilities register reserved bit-63
to indicate HS400 support.

Because HS400 is non-standard for SDHCI, it is possible
that different vendors will do things in different ways.
However HS200 support faced the same issue but currently
there is only one solution.  As such, no attempt has
been made to provide for alternate HS400 solutions except
for SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

1.2V HS200 mode capability is cleared if there is not a voltage
regulator that supports 1.2V.  Do the same for 1.2V HS400 mode.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

supply.vqmmc is used with the IS_ERR macro which means
the value must be valid or an error code.  NULL is
neither, so replace with ERR_PTR(-EINVAL).
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

SDHCI_CTRL_HS_SDR200 is unused.  Remove it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Synopsys DW_MMC IP core supports Internal DMA Controller with 64-bit address mode from IP version 2.70a onwards.
Updated the driver to support IDMAC 64-bit addressing mode.
Signed-off-by: Prabu Thangamuthu <prabu.t@synopsys.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

AMD SD controller supports the SDR104 mode, but caps2 can not
be promoted to support hs200 for eMMC.
Signed-off-by: Vincent Wan <vincent.wan@amd.com>
Signed-off-by: Wan Zongshun <mcuos.com@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This patch is to enable the quirk for AMD sdhci requiring transfer
mode register need to be cleared for commands without data
Signed-off-by: Vincent Wan <vincent.wan@amd.com>
Signed-off-by: Wan Zongshun <mcuos.com@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

SDHC controller in AMD chipsets require SDHC transfer mode
register to be cleared for commands without data. The issue was
uncovered during testing eMMC cards on KB/ML based platforms
Signed-off-by: Vincent Wan <vincent.wan@amd.com>
Signed-off-by: Wan Zongshun <mcuos.com@gmail.com>
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Tested-by: Vikram B <vikram.b@amd.com>
Tested-by: Raghavendra Swamy <raghavendra.swamy@amd.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Signed-off-by: Johan Rudholm <johanru@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

It is possible that we may fail to set the clock rate, if we do so then
log the failure and don't bother reprogramming the IP.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add runtime pm support to atmel mci controller.
Use runtime pm APIs to enable/disable atmel mci's clock.
Use runtime autosuspend APIs to enable auto suspend delay.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[Ulf: Fixed compile error]

The "Badly aligned" tests, test reading/writing with alignments
of 1,2 and 3.  SDHCI now has 64-bit ADMA which has 8-byte
alignment, so extend the tests to test up to 7.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Set a 64-bit DMA mask when using 64-bit DMA.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Set the DMA mask during the first call to ->enable_dma() to
make use of the SDHCI_USE_64_BIT_DMA flag.

This patch is dependent on
commit 8a2f38dd ("ACPI / platform: provide default DMA mask")
which provides the dev->dma_mask pointer without
which dma_set_mask_and_coherent() will always fail.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add 64-bit ADMA support including:
	- add 64-bit ADMA descriptor
	- add SDHCI_USE_64_BIT_DMA flag
	- set upper 32-bits of DMA addresses
	- ability to select 64-bit ADMA
	- ability to use 64-bit ADMA sizes and alignment
	- display "ADMA 64-bit" when host is added

It is assumed that a 64-bit capable device has set a 64-bit DMA mask
and *must* do 64-bit DMA.  A driver has the opportunity to change
that during the first call to ->enable_dma().  Similarly
SDHCI_QUIRK2_BROKEN_64_BIT_DMA must be left to the drivers to
implement.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Define the ADMA descriptor structure instead of
using manual offsets and casts.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Define all the ADMA constants instead of having numbers
scattered throughout the code.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Define the maximum number of segments instead of
having the constant 128 appearing in the code in
various places.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In preparation for 64-bit ADMA, parameterize ADMA sizes
and alignment.  64-bit ADMA has a larger descriptor
because it contains a 64-bit address instead of a 32-bit
address.  Also data must be 8-byte aligned instead
of 4-byte aligned.  Consequently, sdhci_host members
are added for descriptor, table, and buffer sizes
and alignment.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

It is kernel-style to use 'void *' for anonymous data.
This is being applied to the ADMA bounce buffer which
contains unaligned bytes, and to the ADMA descriptor
table which will contain 32-bit ADMA descriptors
or 64-bit ADMA descriptors when support is added.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>