By using SOC_WAKE register it is possible to bring
down power consumption of QCA61X4 from 36mA to
16mA when associated and idle.

Currently the sleep threshold/grace period is at a
very conservative value of 60ms.

Contrary to QCA61X4 the QCA988X firmware doesn't
have Rx/beacon filtering available for client mode
and SWBA events are used for beaconing in AP/IBSS
so the SoC needs to be woken up at least every
~100ms in most cases. This means that QCA988X
is at a disadvantage and the power consumption
won't drop as much as for QCA61X4.

Due to putting irq-safe spinlocks on every MMIO
read/write it is expected this can cause a little
performance regression on some systems. I haven't
done any thorough measurements but some of my
tests don't show any extreme degradation.

The patch removes some explicit pci_wake calls
that were added in 320e14b8db51aa ("ath10k: fix
some pci wake/sleep issues"). This is safe because
all MMIO accesses are now wrapped and the device
is woken up automatically if necessary.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

mac80211 can update vif powersave state while
disconnected. Firmware doesn't behave nicely and
consumes more power than necessary if PS is
disabled on a non-started vdev. Hence
force-enable PS for non-running vdevs.

This reduces power drain on QCA61X4 from 88mA to
36mA when interface is up and not associated.
QCA988X wasn't measured.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

It is actually safe to enable ASPM after the
device is booted up.

This reduces power drain of QCA61X4 when driver is
simply loaded (no interface is up) from 31mA to
14mA. QCA988X wasn't measured but doesn't seem to
regress in any other way.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Fix format specifier used for dma_addr_t, namely use %pad
Debug print virtual address for the same buffer as well.

Fixes: dc16427b ("wil6210: Add pmc debug mechanism memory management")
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Rx clear count reported in wmi_chan_info_event is actually channel_busy_count
not rx_frame_count. Send rx_clear_count through time_busy of survey_info
and set SURVEY_INFO_TIME_BUSY in filled.

iw wlan0 survey dump

urvey data from wlan0
        frequency:                      5180 MHz [in use]
        noise:                          -103 dBm
        channel active time:            150 ms
        channel busy time:              22 ms
Survey data from wlan0
        frequency:                      5200 MHz
        noise:                          -102 dBm
        channel active time:            146 ms
        channel busy time:              0 ms
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Spectral scan supported by ath10k has capability to monitor and report
through whole bands and channels, but current buffer size is too small
to save reported spectral scan data.
This results in dropping 5G channel reports at all when dual band card
is used, so that users are not able to analyze spectral environments.
Hence increase the buffer size to fix the problem.

A spectral data size is vary based on the number of bins, so the unit
buffer size, 1140, is chose to minimize relay buffer fragmentation.

The total buffer size is also chose in tradeoff with spectral scan
support vs. kernel memory consumption.
Since theoretical maximum buffer size, 9.5MB, can be consumed with
512 bins in dual bands, we target to cover up to 128 bins for all
channels in dual bands and due to the buffer size limitation,
spectral scan with bin number bigger than 128 needs to be run on
single band each.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

WSC connection is secure (privacy bit set in various frames)
but authentication suite, keys etc. are absent.

Support this mode in the connect WMI command. Detect WSC by
having 'sme->privacy' and no RSN IE. Inform firmware about WSC
session by setting dot11_auth_mode to WMI_AUTH11_WSC.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Introduce 2 types of GTK, Tx (for this STA) and Rx (for each peer).
Now, AP has only Tx GTK, STA - only Rx one. PBSS not supported yet;
for it, continue using pseudo-DMS.
Handle per-vring .1x state, update it from WMI_VRING_EN_EVENTID
event. This allows unification for unicast and broadcast vrings.
This mechanism replaces former per-CID "data_port_open"
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Pmc is a hardware debug mechanism which allows capturing phy data,
packets, and internally generated events and messages synchronized
and time stamped by the hardware. It requires memory buffers
allocated by the driver in order to be used by hardware dma to
upstream real time debug data to host memory.
Driver will handle memory allocation and release, and fetching
the data from the memory to application layer via debug file
system. The configuration of pmc is handled entirely by the
application layer.
Signed-off-by: Vladimir Shulman <qca_shulmanv@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Parameters for the start_ap and change_bcon contains
probe response template and probe response IE's.

supplicant puts in the proberesp_ies only WPS related IE's,
while firmware need all IE's, most notable is RSN that is not
included in the proberesp_ies.

Always use IE's provided by the bcon->probe_resp
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Boot loader "ready" indication has changed from "bit0 set"
to "only bit0 set". This is to address hardware glitches.
Due to glitches, sometimes right after reset register reads
0xffffffff, or (rarely) other garbage.

Reflect this in the driver
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Rx descriptor fields accordingly to the updated
hardware documentation
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Sometimes it takes for the firmware more than 20ms to
react on "echo" command after reset. Increase timeout
from 20 to 50ms
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

qca6174 otp binary seems to always return an error to the host, even if the
calibration succeeded. Add a firmware feature flag to detect if the firmware
image which have this problem and workaround the issue in ath10k by ignoring
the error code.

I was also considering making this hw specific flag but as this is strictly a
firmware issue it's best to handle this via a firmware feature flag so that it
will be easy to disable the workaround.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Firmware "board" file name has changed from wil6210.board
to wil6210.brd by the FW generation tools.

Reflect this in the driver.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

cfg80211_ops.stop_ap supposed to have interface carried turned off as
post condition. Fulfill this requirement.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Trace where wil6210_disconnect() is called from.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Provide info for [add|del]_key.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

refactor module parameter debug_fw to act as "fw debug mode",
where driver do nothing but allow card memory access.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Major changes in ath10k:

* enable channel 144 on 5 GHz
* enable Adaptive Noise Immunity (ANI) by default
* add Wake on Wireless LAN (WOW) patterns support
* add basic Tunneled Direct Link Setup (TDLS) support
* add multi-channel support for QCA6174
* enable IBSS RSN support
* enable Bluetooth Coexistance whenever firmware supports it
* add more versatile way to set bitrates used by the firmware

Pull networking fixes from David Miller:

 1) mlx4 doesn't check fully for supported valid RSS hash function, fix
    from Amir Vadai

 2) Off by one in ibmveth_change_mtu(), from David Gibson

 3) Prevent altera chip from reporting false error interrupts in some
    circumstances, from Chee Nouk Phoon

 4) Get rid of that stupid endless loop trying to allocate a FIN packet
    in TCP, and in the process kill deadlocks.  From Eric Dumazet

 5) Fix get_rps_cpus() crash due to wrong invalid-cpu value, also from
    Eric Dumazet

 6) Fix two bugs in async rhashtable resizing, from Thomas Graf

 7) Fix topology server listener socket namespace bug in TIPC, from Ying
    Xue

 8) Add some missing HAS_DMA kconfig dependencies, from Geert
    Uytterhoeven

 9) bgmac driver intends to force re-polling but does so by returning
    the wrong value from it's ->poll() handler.  Fix from Rafał Miłecki

10) When the creater of an rhashtable configures a max size for it,
    don't bark in the logs and drop insertions when that is exceeded.
    Fix from Johannes Berg

11) Recover from out of order packets in ppp mppe properly, from Sylvain
    Rochet

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (41 commits)
  bnx2x: really disable TPA if 'disable_tpa' option is set
  net:treewide: Fix typo in drivers/net
  net/mlx4_en: Prevent setting invalid RSS hash function
  mdio-mux-gpio: use new gpiod_get_array and gpiod_put_array functions
  netfilter; Add some missing default cases to switch statements in nft_reject.
  ppp: mppe: discard late packet in stateless mode
  ppp: mppe: sanity error path rework
  net/bonding: Make DRV macros private
  net: rfs: fix crash in get_rps_cpus()
  altera tse: add support for fixed-links.
  pxa168: fix double deallocation of managed resources
  net: fix crash in build_skb()
  net: eth: altera: Resolve false errors from MSGDMA to TSE
  ehea: Fix memory hook reference counting crashes
  net/tg3: Release IRQs on permanent error
  net: mdio-gpio: support access that may sleep
  inet: fix possible panic in reqsk_queue_unlink()
  rhashtable: don't attempt to grow when at max_size
  bgmac: fix requests for extra polling calls from NAPI
  tcp: avoid looping in tcp_send_fin()
  ...

bnx2x's 'disable_tpa=1' module option is not respected properly and TPA
(transparent packet aggregation) remains enabled. Even though the
module option causes LRO to be disabled, TPA is enabled in GRO mode.

Additionally, disabling GRO via ethtool then has no effect. One can
still observe tpa_* statistics increase and large packets being received
in tcpdump.

The bug was an unintended consequence of commit aebf6244 "bnx2x: Be
more forgiving toward SW GRO".

Fix it by following the bp->disable_tpa flag when initializing fp's.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fix spelling typo in printk.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlx4_en_check_rxfh_func() was checking for hardware support before
setting a known RSS hash function, but didn't do any check before
setting unknown RSS hash function. Need to make it fail on such values.
In this occasion, moved the actual setting of the new value from the
check function into mlx4_en_set_rxfh().

Fixes: 947cbb0a ("net/mlx4_en: Support for configurable RSS hash function")
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the new gpiod_get_array and gpiod_put_array functions
(added to mainline in the v4.1 merge window) for obtaining and
disposing of GPIO descriptors.

Cc: David Miller <davem@davemloft.net>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This fixes:

====================
net/netfilter/nft_reject.c: In function ‘nft_reject_dump’:
net/netfilter/nft_reject.c:61:2: warning: enumeration value ‘NFT_REJECT_TCP_RST’ not handled in switch [-Wswitch]
  switch (priv->type) {
  ^
net/netfilter/nft_reject.c:61:2: warning: enumeration value ‘NFT_REJECT_ICMPX_UNREACH’ not handled in switch [-Wswi\
tch]
net/netfilter/nft_reject_inet.c: In function ‘nft_reject_inet_dump’:
net/netfilter/nft_reject_inet.c:105:2: warning: enumeration value ‘NFT_REJECT_TCP_RST’ not handled in switch [-Wswi\
tch]
  switch (priv->type) {
  ^
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Until now only a single fixed tx rate or nss was
allowed to be set.

The patch attempts to improve this by allowing
most bitrate masks. The limitation is VHT MCS
rates cannot be expressed separately using
existing firmware interfaces and only the
following VHT MCS ranges are supported: none, 0-7,
0-8, and 0-9.

This keeps the old behaviour when requesting
single tx rate or single nss. The new bitrate mask
logic is only applied to other cases that would
return -EINVAL until now.

Depending on firmware revisions some combinations
may crash firmware so use with care, please.

This depends on "ath10k: don't use reassoc flag".
Without it key cache would effectively be
invalidated upon bitrate change leading to
communication being no longer possible.

These work:

  iw wlan0 set bitrates legacy-5 6 12 ht-mcs-5 1 2 3
  iw wlan0 set bitrates legacy-5 ht-mcs-5 7 8 9
  iw wlan0 set bitrates legacy-5 24 ht-mcs-5 vht-mcs-5 1:0-9

These won't work:

  iw wlan0 set bitrates legacy-5 ht-mcs-5 vht-mcs-5 1:0-5
  iw wlan0 set bitrates vht-mcs-5 2:7-9

(note the invalid VHT MCS ranges)
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>

Sylvain Rochet says:

====================
ppp: mppe: fixes MPPE desync on links which don't guarantee packet ordering

I am currently having an issue with PPP over L2TP (UDP) and MPPE in
stateless mode (default mode), UDP does not guarantee packet ordering so
we might get out of order packet. MPPE needs to be continuously synched
so we should drop late UDP packet.

I added a printk on the number of time we rekeyed in MPPE decompressor,
this is what we currently have if we receive a slightly out of order UDP
packet:

[1731001.049206] mppe_decompress[1]: ccount 1559
[1731001.049216] mppe_decompress[1]: rekeyed 1 times

[1731001.049228] mppe_decompress[1]: ccount 1560
[1731001.049232] mppe_decompress[1]: rekeyed 1 times

[1731001.050170] mppe_decompress[1]: ccount 1562
[1731001.050182] mppe_decompress[1]: rekeyed 2 times

[1731001.050191] mppe_decompress[1]: ccount 1561
[1731001.062576] mppe_decompress[1]: rekeyed 4095 times
                                             ^^^^
This is obviously wrong, we missed packet 1561 and we already rekeyed 2
times for 1562 we previously received, we can't recover the decryption
key we need for 1561, we should drop it instead of rekeying 4095 times.

This patch series drop any packet with are not within the 4096/2 forward
window.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When PPP is used over a link which does not guarantee packet ordering,
we might get late MPPE packets. This is a problem because MPPE must be
kept synchronized and the current implementation does not drop them and
rekey 4095 times instead of 0, which is wrong.

In order to prevent rekeying about a whole count space times (~ 4095
times), drop packets which are not within the forward 4096/2 window and
increase sanity error counter.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We are going to need sanity error path a little further, rework to be
able to use the sanity error path anywhere in decompressor.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The bonding modules currently defines four macros with
general names that pollute the global namespace:
DRV_VERSION
DRV_RELDATE
DRV_NAME
DRV_DESCRIPTION

Fixing that by defining a private bonding_priv.h
header files which includes those defines.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

AMD CPUs don't reinitialize the SS descriptor on SYSRET, so SYSRET with
SS == 0 results in an invalid usermode state in which SS is apparently
equal to __USER_DS but causes #SS if used.

Work around the issue by setting SS to __KERNEL_DS __switch_to, thus
ensuring that SYSRET never happens with SS set to NULL.

This was exposed by a recent vDSO cleanup.

Fixes: e7d6eefa x86/vdso32/syscall.S: Do not load __USER32_DS to %ss
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Peter Anvin <hpa@zytor.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Brian Gerst <brgerst@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull intel drm fixes from Dave Airlie.

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/i915: vlv: fix save/restore of GFX_MAX_REQ_COUNT reg
  drm/i915: Workaround to avoid lite restore with HEAD==TAIL
  drm/i915: cope with large i2c transfers

Pull intel iommu updates from David Woodhouse:
 "This lays a little of the groundwork for upcoming Shared Virtual
  Memory support — fixing some bogus #defines for capability bits and
  adding the new ones, and starting to use the new wider page tables
  where we can, in anticipation of actually filling in the new fields
  therein.

  It also allows graphics devices to be assigned to VM guests again.
  This got broken in 3.17 by disallowing assignment of RMRR-afflicted
  devices.  Like USB, we do understand why there's an RMRR for graphics
  devices — and unlike USB, it's actually sane.  So we can make an
  exception for graphics devices, just as we do USB controllers.

  Finally, tone down the warning about the X2APIC_OPT_OUT bit, due to
  persistent requests.  X2APIC_OPT_OUT was added to the spec as a nasty
  hack to allow broken BIOSes to forbid us from using X2APIC when they
  do stupid and invasive things and would break if we did.

  Someone noticed that since Windows doesn't have full IOMMU support for
  DMA protection, setting the X2APIC_OPT_OUT bit made Windows avoid
  initialising the IOMMU on the graphics unit altogether.

  This means that it would be available for use in "driver mode", where
  the IOMMU registers are made available through a BAR of the graphics
  device and the graphics driver can do SVM all for itself.

  So they started setting the X2APIC_OPT_OUT bit on *all* platforms with
  SVM capabilities.  And even the platforms which *might*, if the
  planets had been aligned correctly, possibly have had SVM capability
  but which in practice actually don't"

* git://git.infradead.org/intel-iommu:
  iommu/vt-d: support extended root and context entries
  iommu/vt-d: Add new extended capabilities from v2.3 VT-d specification
  iommu/vt-d: Allow RMRR on graphics devices too
  iommu/vt-d: Print x2apic opt out info instead of printing a warning
  iommu/vt-d: kill bogus ecap_niotlb_iunits()

Pull i2c fixes from Wolfram Sang:
 "This has a mixture of merge window cleanups and bugfixes"

* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: st: add include for pinctrl
  i2c: mux: use proper dev when removing "channel-X" symlinks
  i2c: digicolor: remove duplicate include
  i2c: Mark adapter devices with pm_runtime_no_callbacks
  i2c: pca-platform: fix broken email address
  i2c: mxs: fix broken email address
  i2c: rk3x: report number of messages transmitted

Pull btrfs fixes from Chris Mason:
 "Filipe hit two problems in my block group cache patches.  We finalized
  the fixes last week and ran through more tests"

* 'for-linus-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Btrfs: prevent list corruption during free space cache processing
  Btrfs: fix inode cache writeout

Merge tag 'drm-intel-next-fixes-2015-04-25' of git://anongit.freedesktop.org/drm-intel into drm-fixes

three fixes for i915.

* tag 'drm-intel-next-fixes-2015-04-25' of git://anongit.freedesktop.org/drm-intel:
  drm/i915: vlv: fix save/restore of GFX_MAX_REQ_COUNT reg
  drm/i915: Workaround to avoid lite restore with HEAD==TAIL
  drm/i915: cope with large i2c transfers

Pull NFS client updates from Trond Myklebust:
 "Another set of mainly bugfixes and a couple of cleanups.  No new
  functionality in this round.

  Highlights include:

  Stable patches:
   - Fix a regression in /proc/self/mountstats
   - Fix the pNFS flexfiles O_DIRECT support
   - Fix high load average due to callback thread sleeping

  Bugfixes:
   - Various patches to fix the pNFS layoutcommit support
   - Do not cache pNFS deviceids unless server notifications are enabled
   - Fix a SUNRPC transport reconnection regression
   - make debugfs file creation failure non-fatal in SUNRPC
   - Another fix for circular directory warnings on NFSv4 "junctioned"
     mountpoints
   - Fix locking around NFSv4.2 fallocate() support
   - Truncating NFSv4 file opens should also sync O_DIRECT writes
   - Prevent infinite loop in rpcrdma_ep_create()

  Features:
   - Various improvements to the RDMA transport code's handling of
     memory registration
   - Various code cleanups"

* tag 'nfs-for-4.1-1' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: (55 commits)
  fs/nfs: fix new compiler warning about boolean in switch
  nfs: Remove unneeded casts in nfs
  NFS: Don't attempt to decode missing directory entries
  Revert "nfs: replace nfs_add_stats with nfs_inc_stats when add one"
  NFS: Rename idmap.c to nfs4idmap.c
  NFS: Move nfs_idmap.h into fs/nfs/
  NFS: Remove CONFIG_NFS_V4 checks from nfs_idmap.h
  NFS: Add a stub for GETDEVICELIST
  nfs: remove WARN_ON_ONCE from nfs_direct_good_bytes
  nfs: fix DIO good bytes calculation
  nfs: Fetch MOUNTED_ON_FILEID when updating an inode
  sunrpc: make debugfs file creation failure non-fatal
  nfs: fix high load average due to callback thread sleeping
  NFS: Reduce time spent holding the i_mutex during fallocate()
  NFS: Don't zap caches on fallocate()
  xprtrdma: Make rpcrdma_{un}map_one() into inline functions
  xprtrdma: Handle non-SEND completions via a callout
  xprtrdma: Add "open" memreg op
  xprtrdma: Add "destroy MRs" memreg op
  xprtrdma: Add "reset MRs" memreg op
  ...

Pull fourth vfs update from Al Viro:
 "d_inode() annotations from David Howells (sat in for-next since before
  the beginning of merge window) + four assorted fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  RCU pathwalk breakage when running into a symlink overmounting something
  fix I_DIO_WAKEUP definition
  direct-io: only inc/dec inode->i_dio_count for file systems
  fs/9p: fix readdir()
  VFS: assorted d_backing_inode() annotations
  VFS: fs/inode.c helpers: d_inode() annotations
  VFS: fs/cachefiles: d_backing_inode() annotations
  VFS: fs library helpers: d_inode() annotations
  VFS: assorted weird filesystems: d_inode() annotations
  VFS: normal filesystems (and lustre): d_inode() annotations
  VFS: security/: d_inode() annotations
  VFS: security/: d_backing_inode() annotations
  VFS: net/: d_inode() annotations
  VFS: net/unix: d_backing_inode() annotations
  VFS: kernel/: d_inode() annotations
  VFS: audit: d_backing_inode() annotations
  VFS: Fix up some ->d_inode accesses in the chelsio driver
  VFS: Cachefiles should perform fs modifications on the top layer only
  VFS: AF_UNIX sockets should call mknod on the top layer only