bpf_alloc_binary() adds 128 bytes of room to JITed program image
and rounds it up to the nearest page size. If image size is close
to page size (like 4000), it is rounded to two pages:
round_up(4000 + 4 + 128) == 8192
then 'hole' is computed as 8192 - (4000 + 4) = 4188
If prandom_u32() % hole selects a number >= PAGE_SIZE - sizeof(*header)
then kernel will crash during bpf_jit_free():

kernel BUG at arch/x86/mm/pageattr.c:887!
Call Trace:
 [<ffffffff81037285>] change_page_attr_set_clr+0x135/0x460
 [<ffffffff81694cc0>] ? _raw_spin_unlock_irq+0x30/0x50
 [<ffffffff810378ff>] set_memory_rw+0x2f/0x40
 [<ffffffffa01a0d8d>] bpf_jit_free_deferred+0x2d/0x60
 [<ffffffff8106bf98>] process_one_work+0x1d8/0x6a0
 [<ffffffff8106bf38>] ? process_one_work+0x178/0x6a0
 [<ffffffff8106c90c>] worker_thread+0x11c/0x370

since bpf_jit_free() does:
  unsigned long addr = (unsigned long)fp->bpf_func & PAGE_MASK;
  struct bpf_binary_header *header = (void *)addr;
to compute start address of 'bpf_binary_header'
and header->pages will pass junk to:
  set_memory_rw(addr, header->pages);

Fix it by making sure that &header->image[prandom_u32() % hole] and &header
are in the same page

Fixes: 314beb9b ("x86: bpf_jit_comp: secure bpf jit against spraying attacks")
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Included changes:
- properly release neigh_ifinfo in batadv_iv_ogm_process_per_outif()
- properly release orig_ifinfo->router when freeing orig_ifinfo
- properly release neigh_node objects during periodic check
- properly release neigh_info objects when the related hard_iface
  is free'd

These changes are all very important because they fix some
reference counting imbalances that lead to the
impossibility of releasing the netdev object used by
batman-adv on shutdown.
The consequence is that such object cannot be destroyed by
the networking stack (the refcounter does not reach zero)
thus bringing the system in hanging state during a normal
reboot operation or a network reconfiguration.

Since commit 7e980569("ipv6: router reachability probing"), a router falls
into NUD_FAILED will be probed.

Now if function rt6_select() selects a router which neighbour state is NUD_FAILED,
and at the same time function rt6_probe() changes the neighbour state to NUD_PROBE,
then function dst_neigh_output() can directly send packets, but actually the
neighbour still is unreachable. If we set nud_state to NUD_INCOMPLETE instead
NUD_PROBE, packets will not be sent out until the neihbour is reachable.

In addition, because the route should be probes with a single NS, so we must
set neigh->probes to neigh_max_probes(), then the neigh timer timeout and function
neigh_timer_handler() will not send other NS Messages.
Signed-off-by: Duan Jiong <duanj.fnst@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function ip6_tnl_validate assumes that the rtnl
attribute IFLA_IPTUN_PROTO always be filled . If this
attribute is not filled by  the userspace application
kernel get crashed with NULL pointer dereference. This
patch fixes the potential kernel crash when
IFLA_IPTUN_PROTO is missing .
Signed-off-by: Susant Sahani <susant@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the sfc driver is in legacy interrupt mode (either explicitly by
using interrupt_mode module param or by falling back to it) it will
hit a warning at kernel/irq/manage.c because it will try to free an irq
which wasn't allocated by it in the first place because the MSI(X) irqs are
zero and it'll try to free them unconditionally. So fix it by checking if
we're in legacy mode and freeing the appropriate irqs.

CC: Zenghui Shi <zshi@redhat.com>
CC: Ben Hutchings <ben@decadent.org.uk>
CC: <linux-net-drivers@solarflare.com>
CC: Shradha Shah <sshah@solarflare.com>
CC: David S. Miller <davem@davemloft.net>

Fixes: 1899c111 ("sfc: Fix IRQ cleanup in case of a probe failure")
Reported-by: Zenghui Shi <zshi@redhat.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Acked-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Clearing the IFF_ALLMULTI flag on a down interface could cause an allmulti
overflow on the underlying interface.

Attempting the set IFF_ALLMULTI on the underlying interface would cause an
error and the log message:

"allmulti touches root, set allmulti failed."
Signed-off-by: Peter Christensen <pch@ordbogen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix kconfig warnings:

PTP_1588_CLOCK selects NET_PTP_CLASSIFY, which depends on NET,
so PTP_1588_CLOCK should also depend on NET.

PTP_1588_CLOCK_PCH selects PTP_1588_CLOCK so the former should
depend on NET.

warning: (IXP4XX_ETH && PTP_1588_CLOCK) selects NET_PTP_CLASSIFY which has unmet direct dependencies (NET)

warning: (SFC && TILE_NET && BFIN_MAC_USE_HWSTAMP && TIGON3 && FEC && E1000E && IGB && IXGBE && I40E && MLX4_EN && SXGBE_ETH && STMMAC_ETH && TI_CPTS && PTP_1588_CLOCK_GIANFAR && PTP_1588_CLOCK_IXP46X && DP83640_PHY && PTP_1588_CLOCK_PCH) selects PTP_1588_CLOCK which has unmet direct dependencies (NET)
[This warning is caused by the new 'depends on NET' in PTP_1588_CLOCK.]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When an interface is removed separately, all neighbors need to be
checked if they have a neigh_ifinfo structure for that particular
interface. If that is the case, remove that ifinfo so any references to
a hard interface can be freed.

This is a regression introduced by
89652331
("batman-adv: split tq information in neigh_node struct")
Reported-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>

The current code will not execute batadv_purge_orig_neighbors() when an
orig_ifinfo has already been purged. However we need to run it in any
case. Fix that.

This is a regression introduced by
7351a482
("batman-adv: split out router from orig_node")
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>

When an interface is removed from batman-adv, the orig_ifinfo of a
orig_node may be removed without releasing the router first.
This will prevent the reference for the neighbor pointed at by the
orig_ifinfo->router to be released, and this leak may result in
reference leaks for the interface used by this neighbor. Fix that.

This is a regression introduced by
7351a482
("batman-adv: split out router from orig_node").
Reported-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>

The neigh_ifinfo object must be freed if it has been used in
batadv_iv_ogm_process_per_outif().

This is a regression introduced by
89652331
("batman-adv: split tq information in neigh_node struct")
Reported-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>

John W. Linville says:

====================
pull request: wireless 2014-05-08

This one is all from Johannes:

"Here are a few small fixes for the current cycle: radiotap TX flags were
wrong (fix by Bob), Chun-Yeow fixes an SMPS issue with mesh interfaces,
Eliad fixes a locking bug and a cfg80211 state problem and finally
Henning sent me a fix for IBSS rate information."

Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In the cas_lock_tx function we acquire multiple locks in a loop and
need to use nested lock annotation to prevent lockdep warnings.
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 91ebb928b "bnx2x: Add support for Multi-Function UNDI" contains a bug
which prevent the emptying of the device's Rx buffers before reset.
As a result, on new boards it is likely HW will reach some fatal assertion
once its interfaces load after UNDI was previously loaded.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Johan Hovold says:

====================
net: cpsw and mdio-gpio fixes for v3.15-final

These patches against v3.15-rc4 fix a few issues in the cpsw and
mdio-gpio drivers.

Resend with proper stable CC (git send-email still fails to parse the

Sorry about the noise.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add missing of_node_put to avoid kref leak.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix null-pointer dereference at probe when the mdio platform device is
missing (e.g. when it has been disabled in DT).

Cc: stable <stable@vger.kernel.org>	# v3.8
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit f8d56d8f ("net:
 eth: cpsw: Correctly attach to GPIO bitbang MDIO driver").

Fix potential null-pointer dereference at probe if the mdio-gpio device
has not been successfully probed yet.

The offending commit is plain wrong for a number of reasons. First of
all it accesses internal driver data of an unrelated device. Neither
does it check that the data is non-null (which it is in case the device
has not been probed yet).

Furthermore, the decision on whether to treat any driver data according
to the mdio-gpio driver's internals is made based on the node name. But
the name is not compared against "mdio" which is the normal name for the
node, but rather against "gpio" which the node does not have to be named
(and shouldn't be according to the binding documentation). [ If this
hack is to be kept out-of-tree it should at least be matching against
the compatible property. ]

Cc: Stefan Roese <sr@denx.de>
Cc: stable <stable@vger.kernel.org>	# v3.14
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use a sane default bus id (rather than -ENODEV) and print a warning when
the bus alias id is missing.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix aliases syntax in device-tree binding example to avoid
copy-paste errors (the alias would be dropped silently).
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This driver maps 802.1q VLANs to MBIM sessions. The mapping is based on
a bogus assumption that all tagged frames will use the acceleration API
because we enable NETIF_F_HW_VLAN_CTAG_TX. This fails for e.g. frames
tagged in userspace using packet sockets. Such frames will erroneously
be considered as untagged and silently dropped based on not being IP.

Fix by falling back to looking into the ethernet header for a tag if no
accelerated tag was found.

Fixes: a82c7ce5 ("net: cdc_ncm: map MBIM IPS SessionID to VLAN ID")
Cc: Greg Suarez <gsuarez@smithmicro.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following batch contains netfilter fixes for your net tree, they are:

1) Fix use after free in nfnetlink when sending a batch for some
   unsupported subsystem, from Denys Fedoryshchenko.

2) Skip autoload of the nat module if no binding is specified via
   ctnetlink, from Florian Westphal.

3) Set local_df after netfilter defragmentation to avoid a bogus ICMP
   fragmentation needed in the forwarding path, also from Florian.

4) Fix potential user after free in ip6_route_me_harder() when returning
   the error code to the upper layers, from Sergey Popovich.

5) Skip possible bogus ICMP time exceeded emitted from the router (not
   valid according to RFC) if conntrack zones are used, from Vasily Averin.

6) Fix fragment handling when nf_defrag_ipv4 is loaded but nf_conntrack
   is not present, also from Vasily.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This driver adds support for EtherCAT master module located on CCAT
FPGA found on Beckhoff CX series industrial PCs. The driver exposes
EtherCAT master as an ethernet interface.

EtherCAT is a fieldbus protocol defined on top of ethernet and Beckhoff
CX5020 PCs come with built-in EtherCAT master module located on a FPGA,
which in turn is connected to a PCI bus.
Signed-off-by: Dariusz Marcinkiewicz <reksio@newterm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

Similarly, when CONFIG_SYSCTL is not set, ping_group_range should still
work, just that no one can change it. Therefore we should move it out of
sysctl_net_ipv4.c. And, it should not share the same seqlock with
ip_local_port_range.

BTW, rename it to ->ping_group_range instead.

Cc: David S. Miller <davem@davemloft.net>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Reported-by: Stefan de Konink <stefan@konink.de>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When CONFIG_SYSCTL is not set, ip_local_port_range should still work,
just that no one can change it. Therefore we should move it out of sysctl_inet.c.
Also, rename it to ->ip_local_ports instead.

Cc: David S. Miller <davem@davemloft.net>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Reported-by: Stefan de Konink <stefan@konink.de>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Dst is released one line before we access it again with dst->error.

Fixes: 58e35d14 netfilter: ipv6: propagate routing errors from
ip6_route_me_harder()
Signed-off-by: Sergey Popovich <popovich_sergei@mail.ru>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem

If CONFIG_OF is not set, make of_mdiobus_register() call
mdiobus_register() instead of returning -ENOSYS.

This way, we can just call of_mdiobus_register() from all DT-enabled
drivers to handle the compat cases.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Increment fib_info_cnt in fib_create_info() right after successfuly
alllocating fib_info structure, overwise fib_metrics allocation failure
leads to fib_info_cnt incorrectly decremented in free_fib_info(), called
on error path from fib_create_info().
Signed-off-by: Sergey Popovich <popovich_sergei@mail.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rajesh Borundia says:

====================
qlcnic: Bug fixes.

This patch series contain following bug fixes.

* Fix panic where driver was accessing un-initialized crb_intr_mask
  in non Multi-Tx queue mode while dumping TX queue.
* Do not set netdev->real_num_tx_queues directly from driver instead
  use kernel defined netif_set_real_num_tx_queues() API. Also notify
  stack about change in number of Rx queues.

Please apply this series to net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Do not set netdev->real_num_tx_queues directly,
let netif_set_real_num_tx_queues() take care of it.
Do not overwrite netdev->num_tx_queues everytime when driver
changes its Tx ring size through ethtool -L and also notify
stack to update number of Rx queues.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

o In case of non-multi TX queue mode driver does not initialize "crb_intr_mask" pointer
  and driver was accessing that un-initialized pointer while dumping TX queue.
  So dump "crb_intr_mask" only when it is initilaized.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The jme driver forgot to check the return status from pci_map_page in its tx
path, causing a dma api warning on unmap.  Easy fix, just do the check and
augment the tx path to tell the stack that the driver is busy so we re-queue the
frame.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: Guo-Fu Tseng <cooldavid@cooldavid.org>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Westphal says:

====================
net: ip: push gso skb forwarding handling down the stack

Turns out doing the segmentation in forwarding was not a bright idea,
there are corner-cases where this has unintended side-effects.

This patch pushes the segmentation downwards.

After this, netif_skb_dev_features() function can be removed
again, it was only added to fetch the features of the output device,
we can just use skb->dev after the pushdown.

Tested with following setup:

host -> kvm_router  -> kvm_host
  mtu 1500        mtu1280

- 'host' has route to kvm_host with locked mtu of 1500
- gso/gro enabled on all interfaces

Did tests with all of following combinations:
- netfilter conntrack off and on on kvm_router
- virtio-net and e1000 driver on kvm_router
- tcp and udp bulk xmit from host to kvm_host

for tcp, I added TCPMSS mangling on kvm_host to make it lie about tcp mss.

Also added a dummy '-t mangle -A POSTROUTING -p udp -f'
rule to make sure no udp fragments are seen in the 'conntrack on'
and 'virtio-net' case.

Also checked (with ping -M do -s 1400)' that it still sends the wanted
icmp error message when size exceeds 1280.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit d2069403,
there are no more callers.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Doing the segmentation in the forward path has one major drawback:

When using virtio, we may process gso udp packets coming
from host network stack.  In that case, netfilter POSTROUTING
will see one packet with udp header followed by multiple ip
fragments.

Delay the segmentation and do it after POSTROUTING invocation
to avoid this.

Fixes: fe6cc55f ("net: ip, ipv6: handle gso skbs in forwarding path")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

If conntrack defragments incoming ipv6 frags it stores largest original
frag size in ip6cb and sets ->local_df.

We must thus first test the largest original frag size vs. mtu, and not
vice versa.

Without this patch PKTTOOBIG is still generated in ip6_fragment() later
in the stack, but

1) IPSTATS_MIB_INTOOBIGERRORS won't increment
2) packet did (needlessly) traverse netfilter postrouting hook.

Fixes: fe6cc55f ("net: ip, ipv6: handle gso skbs in forwarding path")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

local_df means 'ignore DF bit if set', so if its set we're
allowed to perform ip fragmentation.

This wasn't noticed earlier because the output path also drops such skbs
(and emits needed icmp error) and because netfilter ip defrag did not
set local_df until couple of days ago.

Only difference is that DF-packets-larger-than MTU now discarded
earlier (f.e. we avoid pointless netfilter postrouting trip).

While at it, drop the repeated test ip_exceeds_mtu, checking it once
is enough...

Fixes: fe6cc55f ("net: ip, ipv6: handle gso skbs in forwarding path")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes this warning introduced by commit 5b8f15f7
("net: cdc_mbim: handle IPv6 Neigbor Solicitations"):

===============================
[ INFO: suspicious RCU usage. ]
3.15.0-rc3 #213 Tainted: G        W  O
-------------------------------
net/8021q/vlan_core.c:69 suspicious rcu_dereference_check() usage!

other info that might help us debug this:

rcu_scheduler_active = 1, debug_locks = 1
no locks held by ksoftirqd/0/3.

stack backtrace:
CPU: 0 PID: 3 Comm: ksoftirqd/0 Tainted: G        W  O  3.15.0-rc3 #213
Hardware name: LENOVO 2776LEG/2776LEG, BIOS 6EET55WW (3.15 ) 12/19/2011
 0000000000000001 ffff880232533bf0 ffffffff813a5ee6 0000000000000006
 ffff880232530090 ffff880232533c20 ffffffff81076b94 0000000000000081
 0000000000000000 ffff8802085ac000 ffff88007fc8ea00 ffff880232533c50
Call Trace:
 [<ffffffff813a5ee6>] dump_stack+0x4e/0x68
 [<ffffffff81076b94>] lockdep_rcu_suspicious+0xfa/0x103
 [<ffffffff813978a6>] __vlan_find_dev_deep+0x54/0x94
 [<ffffffffa04a1938>] cdc_mbim_rx_fixup+0x379/0x66a [cdc_mbim]
 [<ffffffff813ab76f>] ? _raw_spin_unlock_irqrestore+0x3a/0x49
 [<ffffffff81079671>] ? trace_hardirqs_on_caller+0x192/0x1a1
 [<ffffffffa059bd10>] usbnet_bh+0x59/0x287 [usbnet]
 [<ffffffff8104067d>] tasklet_action+0xbb/0xcd
 [<ffffffff81040057>] __do_softirq+0x14c/0x30d
 [<ffffffff81040237>] run_ksoftirqd+0x1f/0x50
 [<ffffffff8105f13e>] smpboot_thread_fn+0x172/0x18e
 [<ffffffff8105efcc>] ? SyS_setgroups+0xdf/0xdf
 [<ffffffff810594b0>] kthread+0xb5/0xbd
 [<ffffffff813a84b1>] ? __wait_for_common+0x13b/0x170
 [<ffffffff810593fb>] ? __kthread_parkme+0x5c/0x5c
 [<ffffffff813b147c>] ret_from_fork+0x7c/0xb0
 [<ffffffff810593fb>] ? __kthread_parkme+0x5c/0x5c

Fixes: 5b8f15f7 ("net: cdc_mbim: handle IPv6 Neigbor Solicitations")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>