Page-flipping updates the scanout address, nukes the FBC compressed
image and so forces an FBC update so that the displayed image remains
consistent. However, page-flipping does not update the FBC registers
themselves, which remain pointing to both the old address and the old
CPU fence. Future updates to the new front-buffer (scanout) are then
undetected!

This first approach to demonstrate the issue and highlight the fix,
simply disables FBC upon page-flip (a recompression will be forced on
every flip so FBC becomes immaterial) and then re-enables FBC in the
page-flip finish work function, so that the FBC registers are now
pointing to the new framebuffer and front-buffer rendering works once
more.

Ideally, we want to only re-enable FBC after page-flipping is complete,
as otherwise we are just wasting cycles and power (with needless
recompression) whilst the page-flipping application is still running.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=33487Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>

Persistent mode is intended for use with front-buffer rendering, such as
X, where it is necessary to detect writes to the scanout either by the
GPU or through the CPU's fence, and recompress the dirty regions on the
fly. (By comparison to the back-buffer rendering, the scanout is always
recompressed after a page-flip.)

References: https://bugs.freedesktop.org/show_bug.cgi?id=33487
References: https://bugs.freedesktop.org/show_bug.cgi?id=31742Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>

...and this requirement is enforced by intel_update_fbc() so we can
remove the later check from g4x_enable_fbc() and ironlake_enable_fbc().
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>

The cfb_pitch was only used for 8xx_enable_fbc(), every later routine
was just overwriting the value with itself thanks to a copy'n'paste
error.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>

...to ensure that any pending FBC enable tasklet is cancelled.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>

As the enable/disable routines will be gain additional complexity in
future patches, it is necessary that all callers do not bypass the
generic interface by calling into the chipset routines directly. to do
this we make the chipset routines static, so there is no choice.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>

According to the hardware documentation, GDRST is exactly the same as on
Sandybridge.  So simply enable the existing code.
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Keith Packard <keithp@keithp.com>

On sinks with a DPCD rev of 1.1 or greater, we can send sink power
management commands to address 0x600 per section 5.1.5 of the
DisplayPort 1.1a spec.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>

When checking link status during a hot plug event or detecting sink
presence, we need to retry 3 times per the spec (section 9.1 of the 1.1a
DisplayPort spec).  Consolidate the retry code into a
native_aux_read_retry function for use by get_link_status and _detect.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>

We currently use this when a hot plug event is received, only checking
the link status and re-training if we had previously configured a link.
However if we want to preserve the DP configuration across both hot plug
and DPMS events (which we do for userspace apps that don't respond to
hot plug uevents), we need to unconditionally check the link and try to
bring it up on hot plug.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>

If ->detect is called too soon after a hot plug event, the sink may not
be ready yet.  So try up to 3 times with 1ms sleeps in between tries to
get the data (spec dictates that receivers must be ready to respond within
1ms and that sources should try 3 times).

See section 9.1 of the 1.1a DisplayPort spec.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>

When a hotplug event is received, we need to check the receiver cap bits
in case they've changed (as they might with a hub or chain config).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>

Makes it easier to search for DP related constants.
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>

Especially after a hotplug or power status change, the sink may not
reply immediately to a link status query.  So retry 3 times per the spec
to really make sure nothing is there.

See section 9.1 of the 1.1a DisplayPort spec.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>

Now that we track bpp on a per-pipe basis, we can use the actual value
rather than assuming 24bpp.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>

This will catch bad fb configs earlier.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>

To properly drive a framebuffer with a new depth or bpp, dither settings
and link bandwidth calculations may change, so make sure we go through a
full mode set in that case.
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>

The Intel HDMI encoder can support 8bpc or 12bpc.  Set the appropriate
value based on the pipe bpp when configuring the output.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>

The pipe may be driving various bpp values depending on the display
configuration, so take that into account when calculating link bandwidth
requirements.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>

Updating the planes is device specific, so create a new display callback
and use it in pipe_set_base.  (In fact we could go even further, valid
display plane bits have changed with each generation, as has tiled
buffer handling.)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>

Figuring out which pipe bpp to use is a bit painful.  It depends on both
the encoder and display configuration attached to a pipe.  For instance,
to drive a 24bpp framebuffer out to an 18bpp panel, we need to use 6bpc
on the pipe but also enable dithering.  But driving that same
framebuffer to a DisplayPort output on another pipe means using 8bpc and
no dithering.

So split out and enhance the code to handle the various cases, returning
an appropriate pipe bpp as well as whether dithering should be enabled.

Save the resulting pipe bpp in the intel_crtc struct for use by encoders
in calculating bandwidth requirements (defaults to 24bpp on pre-ILK).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>

This may not be the default value, so pull the bpc out of the pipe reg
and write it to the DP transcoder so proper dithering and signaling
occurs.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>

This prevents us from setting reserved or incorrect bits on CougarPoint.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>

These bits are reserved on ILK+ (ILK+ provides this feature in the
transcoder and pipe configuration instead, which we already set).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (277 commits)
  [SCSI] isci: fix checkpatch errors
  isci: Device reset should request sas_phy_reset(phy, true)
  isci: pare back error messsages
  isci: cleanup silicon revision detection
  isci: merge scu_unsolicited_frame.h into unsolicited_frame_control.h
  isci: merge sata.[ch] into request.c
  isci: kill 'get/set' macros
  isci: retire scic_sds_ and scic_ prefixes
  isci: unify isci_host and scic_sds_controller
  isci: unify isci_remote_device and scic_sds_remote_device
  isci: unify isci_port and scic_sds_port
  isci: fix scic_sds_remote_device_terminate_requests
  isci: unify isci_phy and scic_sds_phy
  isci: unify isci_request and scic_sds_request
  isci: rename / clean up scic_sds_stp_request
  isci: preallocate requests
  isci: combine request flags
  isci: unify can_queue tracking on the tci_pool, uplevel tag assignment
  isci: Terminate dev requests on FIS err bit rx in NCQ
  isci: fix frame received locking
  ...

* 'at91/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-2.6-arm-soc:
  AT91: Change nand buswidth logic to match hardware default configuration
  at91: Use "pclk" as con_id on at91cap9 and at91rm9200
  at91: fix udc, ehci and mmc clock device name for cap9/9g45/9rl
  atmel_serial: fix internal port num
  at91: fix at91_set_serial_console: use platform device id

Merge branch 'fbdev-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-3.x

* 'fbdev-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-3.x:
  vesafb: fix memory leak
  fbdev: amba: Link fb device to its parent
  fsl-diu-fb: remove check for pixel clock ranges
  udlfb: Correct sub-optimal resolution selection.
  hecubafb: add module_put on error path in hecubafb_probe()
  sm501fb: fix section mismatch warning
  gx1fb: Fix section mismatch warnings
  fbdev: sh_mobile_meram: Correct pointer check for YCbCr chroma plane

Commits 71c29bd5 ("IB/uverbs: Add devnode method to set path/mode")
and c3af0980 ("IB: Add devnode methods to cm_class and umad_class")
added devnode methods that set the mode.

However, these methods don't check for a NULL mode, and so we get a
crash when unloading modules because devtmpfs_delete_node() calls
device_get_devnode() with mode == NULL.

Add the missing checks.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.de>
[ Also fix cm.c.  - Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The recently modified nand buswitth configuration is not aligned with
board reality: the double footprint on boards is always populated with 8bits
buswidth nand flashes.
So we have to consider that without particular configuration the 8bits
buswidth is selected by default.
Moreover, the previous logic was always using !board_have_nand_8bit(), we
change it to a simpler: board_have_nand_16bit().
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

When releasing framebuffer, free colourmap allocations.
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
  PM / Runtime: Update documentation regarding driver removal
  PM: Documentation: fix typo: pm_runtime_idle_sync() doesn't exist.

Signed-off-by: James Bottomley <JBottomley@Parallels.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
  cifs: set socket send and receive timeouts before attempting connect

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  hwmon: (k10temp) Update documentation for Fam12h
  hwmon-vid: Fix typo in VIA CPU name
  hwmon: (f71882fg) Add support for the F71869A
  hwmon: Use <> rather than () around my e-mail address
  hwmon: (emc6w201) Properly handle all errors

Add some CPU series IDs and links to the Fam12h datasheets.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

It's Nehemiah, not Nemiah.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>