- 13 Mar, 2020 7 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pmLinus Torvalds authored
Pull power management fix from Rafael Wysocki: "Fix cpupower utility build failures with -fno-common enabled (Mike Gilbert)" * tag 'pm-5.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: cpupower: avoid multiple definition with gcc -fno-common
-
git://git.kernel.dk/linux-blockLinus Torvalds authored
Pull io_uring fix from Jens Axboe: "Just a single fix here, improving the RCU callback ordering from last week. After a bit more perusing by Paul, he poked a hole in the original" * tag 'io_uring-5.6-2020-03-13' of git://git.kernel.dk/linux-block: io_uring: ensure RCU callback ordering with rcu_barrier()
-
git://git.kernel.dk/linux-blockLinus Torvalds authored
Pull block fixes from Jens Axboe: "A few fixes that should go into this release. This contains: - Fix for a corruption issue with the s390 dasd driver (Stefan) - Fixup/improvement for the flush insertion change that we had in this series (Ming) - Fix for the partition suppor for host aware zoned devices (Shin'ichiro) - Fix incorrect blk-iocost comparison (Tejun) The diffstat looks large, but that's a) mostly dasd, and b) the flush fix from Ming adds a big comment" * tag 'block-5.6-2020-03-13' of git://git.kernel.dk/linux-block: block: Fix partition support for host aware zoned block devices blk-mq: insert flush request to the front of dispatch queue s390/dasd: fix data corruption for thin provisioned devices blk-iocost: fix incorrect vtime comparison in iocg_is_idle() -
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmcLinus Torvalds authored
Pull MMC fixes from Ulf Hansson: "MMC core: - Fix HW busy detection support for host controllers requiring the MMC_RSP_BUSY response flag (R1B) to be set for the command. In particular for CMD6 (eMMC), erase/trim/discard (SD/eMMC) and CMD5 (eMMC sleep). MMC host: - sdhci-omap|tegra: Fix support for HW busy detection" * tag 'mmc-v5.6-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: mmc: core: Respect MMC_CAP_NEED_RSP_BUSY for eMMC sleep command mmc: sdhci-tegra: Fix busy detection by enabling MMC_CAP_NEED_RSP_BUSY mmc: sdhci-omap: Fix busy detection by enabling MMC_CAP_NEED_RSP_BUSY mmc: core: Respect MMC_CAP_NEED_RSP_BUSY for erase/trim/discard mmc: core: Allow host controllers to require R1B for CMD6 -
Jann Horn authored
afs_put_addrlist() casts kfree() to rcu_callback_t. Apart from being wrong in theory, this might also blow up when people start enforcing function types via compiler instrumentation, and it means the rcu_head has to be first in struct afs_addr_list. Use kfree_rcu() instead, it's simpler and more correct. Signed-off-by:
Jann Horn <jannh@google.com> Signed-off-by:
David Howells <dhowells@redhat.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
git://anongit.freedesktop.org/drm/drmLinus Torvalds authored
Pull drm fixes from Dave Airlie: "It's a bit quieter, probably not as much as it could be. There is on large regression fix in here from Lyude for displayport bandwidth calculations, there've been reports of multi-monitor in docks not working since -rc1 and this has been tested to fix those. Otherwise it's a bunch of i915 (with some GVT fixes), a set of amdgpu watermark + bios fixes, and an exynos iommu cleanup fix. core: - DP MST bandwidth regression fix. i915: - hard lockup fix - GVT fixes - 32-bit alignment issue fix - timeline wait fixes - cacheline_retire and free amdgpu: - Update the display watermark bounding box for navi14 - Fix fetching vbios directly from rom on vega20/arcturus - Navi and renoir watermark fixes exynos: - iommu object cleanup fix" ` * tag 'drm-fixes-2020-03-13' of git://anongit.freedesktop.org/drm/drm: drm/dp_mst: Rewrite and fix bandwidth limit checks drm/dp_mst: Reprobe path resources in CSN handler drm/dp_mst: Use full_pbn instead of available_pbn for bandwidth checks drm/dp_mst: Rename drm_dp_mst_is_dp_mst_end_device() to be less redundant drm/i915: Defer semaphore priority bumping to a workqueue drm/i915/gt: Close race between cacheline_retire and free drm/i915/execlists: Enable timeslice on partial virtual engine dequeue drm/i915: be more solid in checking the alignment drm/i915/gvt: Fix dma-buf display blur issue on CFL drm/i915: Return early for await_start on same timeline drm/i915: Actually emit the await_start drm/amdgpu/powerplay: nv1x, renior copy dcn clock settings of watermark to smu during boot up drm/exynos: Fix cleanup of IOMMU related objects drm/amdgpu: correct ROM_INDEX/DATA offset for VEGA20 drm/amd/display: update soc bb for nv14 drm/i915/gvt: Fix emulated vbt size issue drm/i915/gvt: Fix unnecessary schedule timer when no vGPU exits
-
Dave Airlie authored
Merge tag 'topic/mst-bw-check-fixes-for-airlied-2020-03-12-2' of git://anongit.freedesktop.org/drm/drm-misc into drm-fixes UAPI Changes: None Cross-subsystem Changes: None Core Changes: Fixed regressions introduced by commit cd82d82c ("drm/dp_mst: Add branch bandwidth validation to MST atomic check"), which would cause us to: * Calculate the available bandwidth on an MST topology incorrectly, and as a result reject most display configurations that would try to enable more then one sink on a topology * Occasionally expose MST connectors to userspace before finishing probing their PBN capabilities, resulting in us rejecting display configurations because we assumed briefly that no bandwidth was available Driver Changes: None Signed-off-by:
Dave Airlie <airlied@redhat.com> From: Lyude Paul <lyude@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/bf16ee577567beed91c86b7d9cda3ec2e8c50a71.camel@redhat.com
-
- 12 Mar, 2020 33 commits
-
-
Dave Airlie authored
Merge tag 'drm-intel-fixes-2020-03-12' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes drm/i915 fixes for v5.6-rc6: - hard lockup fix - GVT fixes - 32-bit alignment issue fix - timeline wait fixes - cacheline_retire and free Signed-off-by:
-
Dave Airlie authored
Merge tag 'amd-drm-fixes-5.6-2020-03-11' of git://people.freedesktop.org/~agd5f/linux into drm-fixes amd-drm-fixes-5.6-2020-03-11: amdgpu: - Update the display watermark bounding box for navi14 - Fix fetching vbios directly from rom on vega20/arcturus - Navi and renoir watermark fixes Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds authored
Pull networking fixes from David Miller: "It looks like a decent sized set of fixes, but a lot of these are one liner off-by-one and similar type changes: 1) Fix netlink header pointer to calcular bad attribute offset reported to user. From Pablo Neira Ayuso. 2) Don't double clear PHY interrupts when ->did_interrupt is set, from Heiner Kallweit. 3) Add missing validation of various (devlink, nl802154, fib, etc.) attributes, from Jakub Kicinski. 4) Missing *pos increments in various netfilter seq_next ops, from Vasily Averin. 5) Missing break in of_mdiobus_register() loop, from Dajun Jin. 6) Don't double bump tx_dropped in veth driver, from Jiang Lidong. 7) Work around FMAN erratum A050385, from Madalin Bucur. 8) Make sure ARP header is pulled early enough in bonding driver, from Eric Dumazet. 9) Do a cond_resched() during multicast processing of ipvlan and macvlan, from Mahesh Bandewar. 10) Don't attach cgroups to unrelated sockets when in interrupt context, from Shakeel Butt. 11) Fix tpacket ring state management when encountering unknown GSO types. From Willem de Bruijn. 12) Fix MDIO bus PHY resume by checking mdio_bus_phy_may_suspend() only in the suspend context. From Heiner Kallweit" * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (112 commits) net: systemport: fix index check to avoid an array out of bounds access tc-testing: add ETS scheduler to tdc build configuration net: phy: fix MDIO bus PM PHY resuming net: hns3: clear port base VLAN when unload PF net: hns3: fix RMW issue for VLAN filter switch net: hns3: fix VF VLAN table entries inconsistent issue net: hns3: fix "tc qdisc del" failed issue taprio: Fix sending packets without dequeueing them net: mvmdio: avoid error message for optional IRQ net: dsa: mv88e6xxx: Add missing mask of ATU occupancy register net: memcg: fix lockdep splat in inet_csk_accept() s390/qeth: implement smarter resizing of the RX buffer pool s390/qeth: refactor buffer pool code s390/qeth: use page pointers to manage RX buffer pool seg6: fix SRv6 L2 tunnels to use IANA-assigned protocol number net: dsa: Don't instantiate phylink for CPU/DSA ports unless needed net/packet: tpacket_rcv: do not increment ring index on drop sxgbe: Fix off by one in samsung driver strncpy size arg net: caif: Add lockdep expression to RCU traversal primitive MAINTAINERS: remove Sathya Perla as Emulex NIC maintainer ... -
Lyude Paul authored
Sigh, this is mostly my fault for not giving commit cd82d82c ("drm/dp_mst: Add branch bandwidth validation to MST atomic check") enough scrutiny during review. The way we're checking bandwidth limitations here is mostly wrong: For starters, drm_dp_mst_atomic_check_bw_limit() determines the pbn_limit of a branch by simply scanning each port on the current branch device, then uses the last non-zero full_pbn value that it finds. It then counts the sum of the PBN used on each branch device for that level, and compares against the full_pbn value it found before. This is wrong because ports can and will have different PBN limitations on many hubs, especially since a number of DisplayPort hubs out there will be clever and only use the smallest link rate required for each downstream sink - potentially giving every port a different full_pbn value depending on what link rate it's trained at. This means with our current code, which max PBN value we end up with is not well defined. Additionally, we also need to remember when checking bandwidth limitations that the top-most device in any MST topology is a branch device, not a port. This means that the first level of a topology doesn't technically have a full_pbn value that needs to be checked. Instead, we should assume that so long as our VCPI allocations fit we're within the bandwidth limitations of the primary MSTB. We do however, want to check full_pbn on every port including those of the primary MSTB. However, it's important to keep in mind that this value represents the minimum link rate /between a port's sink or mstb, and the mstb itself/. A quick diagram to explain: MSTB #1 / \ / \ Port #1 Port #2 full_pbn for Port #1 → | | ← full_pbn for Port #2 Sink #1 MSTB #2 | etc... Note that in the above diagram, the combined PBN from all VCPI allocations on said hub should not exceed the full_pbn value of port #2, and the display configuration on sink #1 should not exceed the full_pbn value of port #1. However, port #1 and port #2 can otherwise consume as much bandwidth as they want so long as their VCPI allocations still fit. And finally - our current bandwidth checking code also makes the mistake of not checking whether something is an end device or not before trying to traverse down it. So, let's fix it by rewriting our bandwidth checking helpers. We split the function into one part for handling branches which simply adds up the total PBN on each branch and returns it, and one for checking each port to ensure we're not going over its PBN limit. Phew. This should fix regressions seen, where we erroneously reject display configurations due to thinking they're going over our bandwidth limits when they're not. Changes since v1: * Took an even closer look at how PBN limitations are supposed to be handled, and did some experimenting with Sean Paul. Ended up rewriting these helpers again, but this time they should actually be correct! Changes since v2: * Small indenting fix * Fix pbn_used check in drm_dp_mst_atomic_check_port_bw_limit() Signed-off-by:
Lyude Paul <lyude@redhat.com> Fixes: cd82d82c ("drm/dp_mst: Add branch bandwidth validation to MST atomic check") Cc: Sean Paul <seanpaul@google.com> Acked-by:
Alex Deucher <alexander.deucher@amd.com> Reviewed-by:
Mikita Lipski <mikita.lipski@amd.com> Tested-by:
Hans de Goede <hdegoede@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200309210131.1497545-1-lyude@redhat.com
-
Lyude Paul authored
We used to punt off reprobing path resources to the link address probe work, but now that we handle CSNs asynchronously from the driver's HPD handling we can do whatever the heck we want from the CSN! So, reprobe the path resources from drm_dp_mst_handle_conn_stat(). Also, get rid of the path resource reprobing code in drm_dp_check_and_send_link_address() since it's needlessly complicated when we already reprobe path resources from drm_dp_handle_link_address_port(). And finally, teach drm_dp_send_enum_path_resources() to return 1 on PBN changes so we know if we need to send another hotplug or not. This fixes issues where we've indicated to userspace that a port has just been connected, before we actually probed it's available PBN - something that results in unexpected atomic check failures. Signed-off-by:
-
Lyude Paul authored
DisplayPort specifications are fun. For a while, it's been really unclear to us what available_pbn actually does. There's a somewhat vague explanation in the DisplayPort spec (starting from 1.2) that partially explains it: The minimum payload bandwidth number supported by the path. Each node updates this number with its available payload bandwidth number if its payload bandwidth number is less than that in the Message Transaction reply. So, it sounds like available_pbn represents the smallest link rate in use between the source and the branch device. Cool, so full_pbn is just the highest possible PBN that the branch device supports right? Well, we assumed that for quite a while until Sean Paul noticed that on some MST hubs, available_pbn will actually get set to 0 whenever there's any active payloads on the respective branch device. This caused quite a bit of confusion since clearing the payload ID table would end up fixing the available_pbn value. So, we just went with that until commit cd82d82c ("drm/dp_mst: Add branch bandwidth validation to MST atomic check") started breaking people's setups due to us getting erroneous available_pbn values. So, we did some more digging and got confused until we finally looked at the definition for full_pbn: The bandwidth of the link at the trained link rate and lane count between the DP Source device and the DP Sink device with no time slots allocated to VC Payloads, represented as a Payload Bandwidth Number. As with the Available_Payload_Bandwidth_Number, this number is determined by the link with the lowest lane count and link rate. That's what we get for not reading specs closely enough, hehe. So, since full_pbn is definitely what we want for doing bandwidth restriction checks - let's start using that instead and ignore available_pbn entirely. Signed-off-by:
-
Lyude Paul authored
It's already prefixed by dp_mst, so we don't really need to repeat ourselves here. One of the changes I should have picked up originally when reviewing MST DSC support. There should be no functional changes here Cc: Mikita Lipski <mikita.lipski@amd.com> Cc: Sean Paul <seanpaul@google.com> Cc: Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfsLinus Torvalds authored
Pull vfs fixes from Al Viro: "A couple of fixes for old crap in ->atomic_open() instances" * 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: cifs_atomic_open(): fix double-put on late allocation failure gfs2_atomic_open(): fix O_EXCL|O_CREAT handling on cold dcache
-
Colin Ian King authored
Currently the bounds check on index is off by one and can lead to an out of bounds access on array priv->filters_loc when index is RXCHK_BRCM_TAG_MAX. Fixes: bb9051a2 ("net: systemport: Add support for WAKE_FILTER") Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Davide Caratti authored
add CONFIG_NET_SCH_ETS to 'config', otherwise test suites using this file to perform a full tdc run will encounter the following warning: ok 645 e90e - Add ETS qdisc using bands # skipped - "-----> teardown stage" did not complete successfully Fixes: 82c664b6 ("selftests: qdiscs: Add test coverage for ETS Qdisc") Reported-by:
Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by:
Davide Caratti <dcaratti@redhat.com> Signed-off-by:
-
Heiner Kallweit authored
So far we have the unfortunate situation that mdio_bus_phy_may_suspend() is called in suspend AND resume path, assuming that function result is the same. After the original change this is no longer the case, resulting in broken resume as reported by Geert. To fix this call mdio_bus_phy_may_suspend() in the suspend path only, and let the phy_device store the info whether it was suspended by MDIO bus PM. Fixes: 503ba7c6 ("net: phy: Avoid multiple suspends") Reported-by:
Geert Uytterhoeven <geert@linux-m68k.org> Tested-by:
Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Al Viro authored
several iterations of ->atomic_open() calling conventions ago, we used to need fput() if ->atomic_open() failed at some point after successful finish_open(). Now (since 2016) it's not needed - struct file carries enough state to make fput() work regardless of the point in struct file lifecycle and discarding it on failure exits in open() got unified. Unfortunately, I'd missed the fact that we had an instance of ->atomic_open() (cifs one) that used to need that fput(), as well as the stale comment in finish_open() demanding such late failure handling. Trivially fixed... Fixes: fe9ec829 "do_last(): take fput() on error after opening to out:" Cc: stable@kernel.org # v4.7+ Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk>
-
Al Viro authored
with the way fs/namei.c:do_last() had been done, ->atomic_open() instances needed to recognize the case when existing file got found with O_EXCL|O_CREAT, either by falling back to finish_no_open() or failing themselves. gfs2 one didn't. Fixes: 6d4ade98 (GFS2: Add atomic_open support) Cc: stable@kernel.org # v3.11 Signed-off-by:
-
David S. Miller authored
Huazhong Tan says: ==================== net: hns3: fixes for -net This series includes several bugfixes for the HNS3 ethernet driver. [patch 1] fixes an "tc qdisc del" failure. [patch 2] fixes SW & HW VLAN table not consistent issue. [patch 3] fixes a RMW issue related to VLAN filter switch. [patch 4] clears port based VLAN when uploading PF. ==================== Signed-off-by: -
Jian Shen authored
Currently, PF missed to clear the port base VLAN for VF when unload. In this case, the VLAN id will remain in the VLAN table. This patch fixes it. Fixes: 92f11ea1 ("net: hns3: fix set port based VLAN issue for VF") Signed-off-by:
Jian Shen <shenjian15@huawei.com> Signed-off-by:
Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by:
-
Jian Shen authored
According to the user manual, the ingress and egress VLAN filter are configured at the same time. Currently, hclge_init_vlan_config() and hclge_set_vlan_spoofchk() will both change the VLAN filter switch. So it's necessary to read the old configuration before modifying it. Fixes: 22044f95 ("net: hns3: add support for spoof check setting") Signed-off-by:
-
Jian Shen authored
Currently, if VF is loaded on the host side, the host doesn't clear the VF's VLAN table entries when VF removing. In this case, when doing reset and disabling sriov at the same time the VLAN device over VF will be removed, but the VLAN table entries in hardware are remained. This patch fixes it by asking PF to clear the VLAN table entries for VF when VF is removing. It also clears the VLAN table full bit after VF VLAN table entries being cleared. Fixes: c6075b19 ("net: hns3: Record VF vlan tables") Signed-off-by:
-
Yonglong Liu authored
The HNS3 driver supports to configure TC numbers and TC to priority map via "tc" tool. But when delete the rule, will fail, because the HNS3 driver needs at least one TC, but the "tc" tool sets TC number to zero when delete. This patch makes sure that the TC number is at least one. Fixes: 30d240df ("net: hns3: Add mqprio hardware offload support in hns3 driver") Signed-off-by:
Yonglong Liu <liuyonglong@huawei.com> Signed-off-by:
-
Vinicius Costa Gomes authored
There was a bug that was causing packets to be sent to the driver without first calling dequeue() on the "child" qdisc. And the KASAN report below shows that sending a packet without calling dequeue() leads to bad results. The problem is that when checking the last qdisc "child" we do not set the returned skb to NULL, which can cause it to be sent to the driver, and so after the skb is sent, it may be freed, and in some situations a reference to it may still be in the child qdisc, because it was never dequeued. The crash log looks like this: [ 19.937538] ================================================================== [ 19.938300] BUG: KASAN: use-after-free in taprio_dequeue_soft+0x620/0x780 [ 19.938968] Read of size 4 at addr ffff8881128628cc by task swapper/1/0 [ 19.939612] [ 19.939772] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.6.0-rc3+ #97 [ 19.940397] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qe4 [ 19.941523] Call Trace: [ 19.941774] <IRQ> [ 19.941985] dump_stack+0x97/0xe0 [ 19.942323] print_address_description.constprop.0+0x3b/0x60 [ 19.942884] ? taprio_dequeue_soft+0x620/0x780 [ 19.943325] ? taprio_dequeue_soft+0x620/0x780 [ 19.943767] __kasan_report.cold+0x1a/0x32 [ 19.944173] ? taprio_dequeue_soft+0x620/0x780 [ 19.944612] kasan_report+0xe/0x20 [ 19.944954] taprio_dequeue_soft+0x620/0x780 [ 19.945380] __qdisc_run+0x164/0x18d0 [ 19.945749] net_tx_action+0x2c4/0x730 [ 19.946124] __do_softirq+0x268/0x7bc [ 19.946491] irq_exit+0x17d/0x1b0 [ 19.946824] smp_apic_timer_interrupt+0xeb/0x380 [ 19.947280] apic_timer_interrupt+0xf/0x20 [ 19.947687] </IRQ> [ 19.947912] RIP: 0010:default_idle+0x2d/0x2d0 [ 19.948345] Code: 00 00 41 56 41 55 65 44 8b 2d 3f 8d 7c 7c 41 54 55 53 0f 1f 44 00 00 e8 b1 b2 c5 fd e9 07 00 3 [ 19.950166] RSP: 0018:ffff88811a3efda0 EFLAGS: 00000282 ORIG_RAX: ffffffffffffff13 [ 19.950909] RAX: 0000000080000000 RBX: ffff88811a3a9600 RCX: ffffffff8385327e [ 19.951608] RDX: 1ffff110234752c0 RSI: 0000000000000000 RDI: ffffffff8385262f [ 19.952309] RBP: ffffed10234752c0 R08: 0000000000000001 R09: ffffed10234752c1 [ 19.953009] R10: ffffed10234752c0 R11: ffff88811a3a9607 R12: 0000000000000001 [ 19.953709] R13: 0000000000000001 R14: 0000000000000000 R15: 0000000000000000 [ 19.954408] ? default_idle_call+0x2e/0x70 [ 19.954816] ? default_idle+0x1f/0x2d0 [ 19.955192] default_idle_call+0x5e/0x70 [ 19.955584] do_idle+0x3d4/0x500 [ 19.955909] ? arch_cpu_idle_exit+0x40/0x40 [ 19.956325] ? _raw_spin_unlock_irqrestore+0x23/0x30 [ 19.956829] ? trace_hardirqs_on+0x30/0x160 [ 19.957242] cpu_startup_entry+0x19/0x20 [ 19.957633] start_secondary+0x2a6/0x380 [ 19.958026] ? set_cpu_sibling_map+0x18b0/0x18b0 [ 19.958486] secondary_startup_64+0xa4/0xb0 [ 19.958921] [ 19.959078] Allocated by task 33: [ 19.959412] save_stack+0x1b/0x80 [ 19.959747] __kasan_kmalloc.constprop.0+0xc2/0xd0 [ 19.960222] kmem_cache_alloc+0xe4/0x230 [ 19.960617] __alloc_skb+0x91/0x510 [ 19.960967] ndisc_alloc_skb+0x133/0x330 [ 19.961358] ndisc_send_ns+0x134/0x810 [ 19.961735] addrconf_dad_work+0xad5/0xf80 [ 19.962144] process_one_work+0x78e/0x13a0 [ 19.962551] worker_thread+0x8f/0xfa0 [ 19.962919] kthread+0x2ba/0x3b0 [ 19.963242] ret_from_fork+0x3a/0x50 [ 19.963596] [ 19.963753] Freed by task 33: [ 19.964055] save_stack+0x1b/0x80 [ 19.964386] __kasan_slab_free+0x12f/0x180 [ 19.964830] kmem_cache_free+0x80/0x290 [ 19.965231] ip6_mc_input+0x38a/0x4d0 [ 19.965617] ipv6_rcv+0x1a4/0x1d0 [ 19.965948] __netif_receive_skb_one_core+0xf2/0x180 [ 19.966437] netif_receive_skb+0x8c/0x3c0 [ 19.966846] br_handle_frame_finish+0x779/0x1310 [ 19.967302] br_handle_frame+0x42a/0x830 [ 19.967694] __netif_receive_skb_core+0xf0e/0x2a90 [ 19.968167] __netif_receive_skb_one_core+0x96/0x180 [ 19.968658] process_backlog+0x198/0x650 [ 19.969047] net_rx_action+0x2fa/0xaa0 [ 19.969420] __do_softirq+0x268/0x7bc [ 19.969785] [ 19.969940] The buggy address belongs to the object at ffff888112862840 [ 19.969940] which belongs to the cache skbuff_head_cache of size 224 [ 19.971202] The buggy address is located 140 bytes inside of [ 19.971202] 224-byte region [ffff888112862840, ffff888112862920) [ 19.972344] The buggy address belongs to the page: [ 19.972820] page:ffffea00044a1800 refcount:1 mapcount:0 mapping:ffff88811a2bd1c0 index:0xffff8881128625c0 compo0 [ 19.973930] flags: 0x8000000000010200(slab|head) [ 19.974388] raw: 8000000000010200 ffff88811a2ed650 ffff88811a2ed650 ffff88811a2bd1c0 [ 19.975151] raw: ffff8881128625c0 0000000000190013 00000001ffffffff 0000000000000000 [ 19.975915] page dumped because: kasan: bad access detected [ 19.976461] page_owner tracks the page as allocated [ 19.976946] page last allocated via order 2, migratetype Unmovable, gfp_mask 0xd20c0(__GFP_IO|__GFP_FS|__GFP_NO) [ 19.978332] prep_new_page+0x24b/0x330 [ 19.978707] get_page_from_freelist+0x2057/0x2c90 [ 19.979170] __alloc_pages_nodemask+0x218/0x590 [ 19.979619] new_slab+0x9d/0x300 [ 19.979948] ___slab_alloc.constprop.0+0x2f9/0x6f0 [ 19.980421] __slab_alloc.constprop.0+0x30/0x60 [ 19.980870] kmem_cache_alloc+0x201/0x230 [ 19.981269] __alloc_skb+0x91/0x510 [ 19.981620] alloc_skb_with_frags+0x78/0x4a0 [ 19.982043] sock_alloc_send_pskb+0x5eb/0x750 [ 19.982476] unix_stream_sendmsg+0x399/0x7f0 [ 19.982904] sock_sendmsg+0xe2/0x110 [ 19.983262] ____sys_sendmsg+0x4de/0x6d0 [ 19.983660] ___sys_sendmsg+0xe4/0x160 [ 19.984032] __sys_sendmsg+0xab/0x130 [ 19.984396] do_syscall_64+0xe7/0xae0 [ 19.984761] page last free stack trace: [ 19.985142] __free_pages_ok+0x432/0xbc0 [ 19.985533] qlist_free_all+0x56/0xc0 [ 19.985907] quarantine_reduce+0x149/0x170 [ 19.986315] __kasan_kmalloc.constprop.0+0x9e/0xd0 [ 19.986791] kmem_cache_alloc+0xe4/0x230 [ 19.987182] prepare_creds+0x24/0x440 [ 19.987548] do_faccessat+0x80/0x590 [ 19.987906] do_syscall_64+0xe7/0xae0 [ 19.988276] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 19.988775] [ 19.988930] Memory state around the buggy address: [ 19.989402] ffff888112862780: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc [ 19.990111] ffff888112862800: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb [ 19.990822] >ffff888112862880: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb [ 19.991529] ^ [ 19.992081] ffff888112862900: fb fb fb fb fc fc fc fc fc fc fc fc fc fc fc fc [ 19.992796] ffff888112862980: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc Fixes: 5a781ccb ("tc: Add support for configuring the taprio scheduler") Reported-by:
Michael Schmidt <michael.schmidt@eti.uni-siegen.de> Signed-off-by:
Vinicius Costa Gomes <vinicius.gomes@intel.com> Acked-by:
Andre Guedes <andre.guedes@intel.com> Signed-off-by:
-
git://github.com/cminyard/linux-ipmiLinus Torvalds authored
Pull IPMI fix from Corey Minyard: "Fix a message spew on some system The call to platform_get_irq() was changed to print a log if the interrupt was not available, and that was causing bogus messages to spew out for the IPMI driver. People have requested that this get in to 5.6 so I'm sending it along" * tag 'for-linus-5.6-2' of git://github.com/cminyard/linux-ipmi: ipmi_si: Avoid spurious errors for optional IRQs
-
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6Linus Torvalds authored
Pull crypto fix from Herbert Xu: "Fix a build problem with x86/curve25519" * 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: crypto: x86/curve25519 - support assemblers with no adx support
-
Shin'ichiro Kawasaki authored
Commit b7205307 ("block: allow partitions on host aware zone devices") introduced the helper function disk_has_partitions() to check if a given disk has valid partitions. However, since this function result directly depends on the disk partition table length rather than the actual existence of valid partitions in the table, it returns true even after all partitions are removed from the disk. For host aware zoned block devices, this results in zone management support to be kept disabled even after removing all partitions. Fix this by changing disk_has_partitions() to walk through the partition table entries and return true if and only if a valid non-zero size partition is found. Fixes: b7205307 ("block: allow partitions on host aware zone devices") Cc: stable@vger.kernel.org # 5.5 Reviewed-by:
Damien Le Moal <damien.lemoal@wdc.com> Reviewed-by:
Johannes Thumshirn <johannes.thumshirn@wdc.com> Reviewed-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com> Signed-off-by:
Jens Axboe <axboe@kernel.dk>
-
Ming Lei authored
commit 01e99aec ("blk-mq: insert passthrough request into hctx->dispatch directly") may change to add flush request to the tail of dispatch by applying the 'add_head' parameter of blk_mq_sched_insert_request. Turns out this way causes performance regression on NCQ controller because flush is non-NCQ command, which can't be queued when there is any in-flight NCQ command. When adding flush rq to the front of hctx->dispatch, it is easier to introduce extra time to flush rq's latency compared with adding to the tail of dispatch queue because of S_SCHED_RESTART, then chance of flush merge is increased, and less flush requests may be issued to controller. So always insert flush request to the front of dispatch queue just like before applying commit 01e99aec ("blk-mq: insert passthrough request into hctx->dispatch directly"). Cc: Damien Le Moal <Damien.LeMoal@wdc.com> Cc: Shinichiro Kawasaki <shinichiro.kawasaki@wdc.com> Reported-by:
Ming Lei <ming.lei@redhat.com> Signed-off-by:
-
Stefan Haberland authored
Devices are formatted in multiple of tracks. For an Extent Space Efficient (ESE) volume we get errors when accessing unformatted tracks. In this case the driver either formats the track on the flight for write requests or returns zero data for read requests. In case a request spans multiple tracks, the indication of an unformatted track presented for the first track is incorrectly applied to all tracks covered by the request. As a result, tracks containing data will be handled as empty, resulting in zero data being returned on read, or overwriting existing data with zero on write. Fix by determining the track that gets the NRF error. For write requests only format the track that is surely not formatted. For Read requests all tracks before have returned valid data and should not be touched. All tracks after the unformatted track might be formatted or not. Those are returned to the blocklayer to build a new request. When using alias devices there is a chance that multiple write requests trigger a format of the same track which might lead to data loss. Ensure that a track is formatted only once by maintaining a list of currently processed tracks. Fixes: 5e2b17e7 ("s390/dasd: Add dynamic formatting support for ESE volumes") Cc: stable@vger.kernel.org # 5.3+ Signed-off-by:
Stefan Haberland <sth@linux.ibm.com> Reviewed-by:
Jan Hoeppner <hoeppner@linux.ibm.com> Reviewed-by:
Peter Oberparleiter <oberpar@linux.ibm.com> Signed-off-by:
-
Ulf Hansson authored
The busy timeout for the CMD5 to put the eMMC into sleep state, is specific to the card. Potentially the timeout may exceed the host->max_busy_timeout. If that becomes the case, mmc_sleep() converts from using an R1B response to an R1 response, as to prevent the host from doing HW busy detection. However, it has turned out that some hosts requires an R1B response no matter what, so let's respect that via checking MMC_CAP_NEED_RSP_BUSY. Note that, if the R1B gets enforced, the host becomes fully responsible of managing the needed busy timeout, in one way or the other. Suggested-by:
Sowjanya Komatineni <skomatineni@nvidia.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20200311092036.16084-1-ulf.hansson@linaro.orgSigned-off-by:
Ulf Hansson <ulf.hansson@linaro.org>
-
Chris Packham authored
Per the dt-binding the interrupt is optional so use platform_get_irq_optional() instead of platform_get_irq(). Since commit 7723f4c5 ("driver core: platform: Add an error message to platform_get_irq*()") platform_get_irq() produces an error message orion-mdio f1072004.mdio: IRQ index 0 not found which is perfectly normal if one hasn't specified the optional property in the device tree. Signed-off-by:
Chris Packham <chris.packham@alliedtelesis.co.nz> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
Andrew Lunn authored
Only the bottom 12 bits contain the ATU bin occupancy statistics. The upper bits need masking off. Fixes: e0c69ca7 ("net: dsa: mv88e6xxx: Add ATU occupancy via devlink resources") Signed-off-by:
-
Eric Dumazet authored
Locking newsk while still holding the listener lock triggered a lockdep splat [1] We can simply move the memcg code after we release the listener lock, as this can also help if multiple threads are sharing a common listener. Also fix a typo while reading socket sk_rmem_alloc. [1] WARNING: possible recursive locking detected 5.6.0-rc3-syzkaller #0 Not tainted -------------------------------------------- syz-executor598/9524 is trying to acquire lock: ffff88808b5b8b90 (sk_lock-AF_INET6){+.+.}, at: lock_sock include/net/sock.h:1541 [inline] ffff88808b5b8b90 (sk_lock-AF_INET6){+.+.}, at: inet_csk_accept+0x69f/0xd30 net/ipv4/inet_connection_sock.c:492 but task is already holding lock: ffff88808b5b9590 (sk_lock-AF_INET6){+.+.}, at: lock_sock include/net/sock.h:1541 [inline] ffff88808b5b9590 (sk_lock-AF_INET6){+.+.}, at: inet_csk_accept+0x8d/0xd30 net/ipv4/inet_connection_sock.c:445 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(sk_lock-AF_INET6); lock(sk_lock-AF_INET6); *** DEADLOCK *** May be due to missing lock nesting notation 1 lock held by syz-executor598/9524: #0: ffff88808b5b9590 (sk_lock-AF_INET6){+.+.}, at: lock_sock include/net/sock.h:1541 [inline] #0: ffff88808b5b9590 (sk_lock-AF_INET6){+.+.}, at: inet_csk_accept+0x8d/0xd30 net/ipv4/inet_connection_sock.c:445 stack backtrace: CPU: 0 PID: 9524 Comm: syz-executor598 Not tainted 5.6.0-rc3-syzkaller #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0x188/0x20d lib/dump_stack.c:118 print_deadlock_bug kernel/locking/lockdep.c:2370 [inline] check_deadlock kernel/locking/lockdep.c:2411 [inline] validate_chain kernel/locking/lockdep.c:2954 [inline] __lock_acquire.cold+0x114/0x288 kernel/locking/lockdep.c:3954 lock_acquire+0x197/0x420 kernel/locking/lockdep.c:4484 lock_sock_nested+0xc5/0x110 net/core/sock.c:2947 lock_sock include/net/sock.h:1541 [inline] inet_csk_accept+0x69f/0xd30 net/ipv4/inet_connection_sock.c:492 inet_accept+0xe9/0x7c0 net/ipv4/af_inet.c:734 __sys_accept4_file+0x3ac/0x5b0 net/socket.c:1758 __sys_accept4+0x53/0x90 net/socket.c:1809 __do_sys_accept4 net/socket.c:1821 [inline] __se_sys_accept4 net/socket.c:1818 [inline] __x64_sys_accept4+0x93/0xf0 net/socket.c:1818 do_syscall_64+0xf6/0x790 arch/x86/entry/common.c:294 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x4445c9 Code: e8 0c 0d 03 00 48 83 c4 18 c3 0f 1f 80 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 eb 08 fc ff c3 66 2e 0f 1f 84 00 00 00 00 RSP: 002b:00007ffc35b37608 EFLAGS: 00000246 ORIG_RAX: 0000000000000120 RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 00000000004445c9 RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000003 RBP: 0000000000000000 R08: 0000000000306777 R09: 0000000000306777 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 R13: 00000000004053d0 R14: 0000000000000000 R15: 0000000000000000 Fixes: d752a498 ("net: memcg: late association of sock to memcg") Signed-off-by:Eric Dumazet <edumazet@google.com> Cc: Shakeel Butt <shakeelb@google.com> Reported-by:
syzbot <syzkaller@googlegroups.com> Signed-off-by:
-
David S. Miller authored
Julian Wiedmann says: ==================== s390/qeth: fixes 2020-03-11 please apply the following patch series for qeth to netdev's net tree. Just one fix to get the RX buffer pool resizing right, with two preparatory cleanups. This is on the larger side given where we are in the -rc cycle, but a big chunk of the delta is just refactoring to make the fix look nice. I intentionally split these off from yesterday's series. No objections if you'd rather punt them to net-next, the series should apply cleanly. ==================== Signed-off-by: -
Julian Wiedmann authored
The RX buffer pool is allocated in qeth_alloc_qdio_queues(). A subsequent pool resizing is then handled in a very simple way: first free the current pool, then allocate a new pool of the requested size. There's two ways where this can go wrong: 1. if the resize action happens _before_ the initial pool was allocated, then a subsequent initialization will call qeth_alloc_qdio_queues() and fill the pool with a second(!) set of pages. We consume twice the planned amount of memory. This is easy to fix - just skip the resizing if the queues haven't been allocated yet. 2. if the initial pool was created by qeth_alloc_qdio_queues() but a subsequent resizing fails, then the device has no(!) RX buffer pool. The next initialization will _not_ call qeth_alloc_qdio_queues(), and attempting to back the RX buffers with pages in qeth_init_qdio_queues() will fail. Not very difficult to fix either - instead of re-allocating the whole pool, just allocate/free as many entries to match the desired size. Fixes: 4a71df50 ("qeth: new qeth device driver") Signed-off-by:
Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by:
-
Julian Wiedmann authored
In preparation for a subsequent fix, split out helpers to allocate/free individual pool entries. Signed-off-by:
-
Julian Wiedmann authored
The RX buffer elements are always backed with full pages, reflect this in the pointer type. Signed-off-by:
-
Paolo Lungaroni authored
The Internet Assigned Numbers Authority (IANA) has recently assigned a protocol number value of 143 for Ethernet [1]. Before this assignment, encapsulation mechanisms such as Segment Routing used the IPv6-NoNxt protocol number (59) to indicate that the encapsulated payload is an Ethernet frame. In this patch, we add the definition of the Ethernet protocol number to the kernel headers and update the SRv6 L2 tunnels to use it. [1] https://www.iana.org/assignments/protocol-numbers/protocol-numbers.xhtmlSigned-off-by:
Paolo Lungaroni <paolo.lungaroni@cnit.it> Reviewed-by:
Andrea Mayer <andrea.mayer@uniroma2.it> Acked-by:
Ahmed Abdelsalam <ahmed.abdelsalam@gssi.it> Signed-off-by:
-
