- 04 Jun, 2012 15 commits
-
-
Arik Nemtsov authored
sta_info_cleanup locks the sta_list using rcu_read_lock however the delete operation isn't rcu safe. A race between sta_info_cleanup timer being called and a STA being removed can occur which leads to a panic while traversing sta_list. Fix this by switching to the RCU-safe versions. Cc: stable@vger.kernel.org Reported-by:
Eyal Shapira <eyal@wizery.com> Signed-off-by:
Arik Nemtsov <arik@wizery.com> Signed-off-by:
John W. Linville <linville@tuxdriver.com>
-
Seth Forshee authored
MacBook Pro models with BCM4331 wireless have been found to have the ext PA lines disabled after resuming from S3 without external power attach. This causes them to be unable to transmit. Add a workaround to ensure that the ext PA lines are enabled on BCM4331. Also extend all handling of ext PA line muxing to BCM43431 as is done in the Broadcom SDK. BugLink: http://bugs.launchpad.net/bugs/925577 Cc: Arend van Spriel <arend@broadcom.com> Cc: Hauke Mehrtens <hauke@hauke-m.de> Cc: stable@vger.kernel.org Signed-off-by:
Seth Forshee <seth.forshee@canonical.com> Signed-off-by:
-
Stanislaw Gruszka authored
Remove spinlock as atomic_t can be used instead. Note we use only 16 lower bits, upper bits are changed but we impilcilty cast to u16. This fix possible deadlock on IBSS mode reproted by lockdep: ================================= [ INFO: inconsistent lock state ] 3.4.0-wl+ #4 Not tainted --------------------------------- inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage. kworker/u:2/30374 [HC0[0]:SC0[0]:HE1:SE1] takes: (&(&intf->seqlock)->rlock){+.?...}, at: [<f9979a20>] rt2x00queue_create_tx_descriptor+0x380/0x490 [rt2x00lib] {IN-SOFTIRQ-W} state was registered at: [<c04978ab>] __lock_acquire+0x47b/0x1050 [<c0498504>] lock_acquire+0x84/0xf0 [<c0835733>] _raw_spin_lock+0x33/0x40 [<f9979a20>] rt2x00queue_create_tx_descriptor+0x380/0x490 [rt2x00lib] [<f9979f2a>] rt2x00queue_write_tx_frame+0x1a/0x300 [rt2x00lib] [<f997834f>] rt2x00mac_tx+0x7f/0x380 [rt2x00lib] [<f98fe363>] __ieee80211_tx+0x1b3/0x300 [mac80211] [<f98ffdf5>] ieee80211_tx+0x105/0x130 [mac80211] [<f99000dd>] ieee80211_xmit+0xad/0x100 [mac80211] [<f9900519>] ieee80211_subif_start_xmit+0x2d9/0x930 [mac80211] [<c0782e87>] dev_hard_start_xmit+0x307/0x660 [<c079bb71>] sch_direct_xmit+0xa1/0x1e0 [<c0784bb3>] dev_queue_xmit+0x183/0x730 [<c078c27a>] neigh_resolve_output+0xfa/0x1e0 [<c07b436a>] ip_finish_output+0x24a/0x460 [<c07b4897>] ip_output+0xb7/0x100 [<c07b2d60>] ip_local_out+0x20/0x60 [<c07e01ff>] igmpv3_sendpack+0x4f/0x60 [<c07e108f>] igmp_ifc_timer_expire+0x29f/0x330 [<c04520fc>] run_timer_softirq+0x15c/0x2f0 [<c0449e3e>] __do_softirq+0xae/0x1e0 irq event stamp: 18380437 hardirqs last enabled at (18380437): [<c0526027>] __slab_alloc.clone.3+0x67/0x5f0 hardirqs last disabled at (18380436): [<c0525ff3>] __slab_alloc.clone.3+0x33/0x5f0 softirqs last enabled at (18377616): [<c0449eb3>] __do_softirq+0x123/0x1e0 softirqs last disabled at (18377611): [<c041278d>] do_softirq+0x9d/0xe0 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&(&intf->seqlock)->rlock); <Interrupt> lock(&(&intf->seqlock)->rlock); *** DEADLOCK *** 4 locks held by kworker/u:2/30374: #0: (wiphy_name(local->hw.wiphy)){++++.+}, at: [<c045cf99>] process_one_work+0x109/0x3f0 #1: ((&sdata->work)){+.+.+.}, at: [<c045cf99>] process_one_work+0x109/0x3f0 #2: (&ifibss->mtx){+.+.+.}, at: [<f98f005b>] ieee80211_ibss_work+0x1b/0x470 [mac80211] #3: (&intf->beacon_skb_mutex){+.+...}, at: [<f997a644>] rt2x00queue_update_beacon+0x24/0x50 [rt2x00lib] stack backtrace: Pid: 30374, comm: kworker/u:2 Not tainted 3.4.0-wl+ #4 Call Trace: [<c04962a6>] print_usage_bug+0x1f6/0x220 [<c0496a12>] mark_lock+0x2c2/0x300 [<c0495ff0>] ? check_usage_forwards+0xc0/0xc0 [<c04978ec>] __lock_acquire+0x4bc/0x1050 [<c0527890>] ? __kmalloc_track_caller+0x1c0/0x1d0 [<c0777fb6>] ? copy_skb_header+0x26/0x90 [<c0498504>] lock_acquire+0x84/0xf0 [<f9979a20>] ? rt2x00queue_create_tx_descriptor+0x380/0x490 [rt2x00lib] [<c0835733>] _raw_spin_lock+0x33/0x40 [<f9979a20>] ? rt2x00queue_create_tx_descriptor+0x380/0x490 [rt2x00lib] [<f9979a20>] rt2x00queue_create_tx_descriptor+0x380/0x490 [rt2x00lib] [<f997a5cf>] rt2x00queue_update_beacon_locked+0x5f/0xb0 [rt2x00lib] [<f997a64d>] rt2x00queue_update_beacon+0x2d/0x50 [rt2x00lib] [<f9977e3a>] rt2x00mac_bss_info_changed+0x1ca/0x200 [rt2x00lib] [<f9977c70>] ? rt2x00mac_remove_interface+0x70/0x70 [rt2x00lib] [<f98e4dd0>] ieee80211_bss_info_change_notify+0xe0/0x1d0 [mac80211] [<f98ef7b8>] __ieee80211_sta_join_ibss+0x3b8/0x610 [mac80211] [<c0496ab4>] ? mark_held_locks+0x64/0xc0 [<c0440012>] ? virt_efi_query_capsule_caps+0x12/0x50 [<f98efb09>] ieee80211_sta_join_ibss+0xf9/0x140 [mac80211] [<f98f0456>] ieee80211_ibss_work+0x416/0x470 [mac80211] [<c0496d8b>] ? trace_hardirqs_on+0xb/0x10 [<c077683b>] ? skb_dequeue+0x4b/0x70 [<f98f207f>] ieee80211_iface_work+0x13f/0x230 [mac80211] [<c045cf99>] ? process_one_work+0x109/0x3f0 [<c045d015>] process_one_work+0x185/0x3f0 [<c045cf99>] ? process_one_work+0x109/0x3f0 [<f98f1f40>] ? ieee80211_teardown_sdata+0xa0/0xa0 [mac80211] [<c045ed86>] worker_thread+0x116/0x270 [<c045ec70>] ? manage_workers+0x1e0/0x1e0 [<c0462f64>] kthread+0x84/0x90 [<c0462ee0>] ? __init_kthread_worker+0x60/0x60 [<c083d382>] kernel_thread_helper+0x6/0x10 Cc: stable@vger.kernel.org Signed-off-by:Stanislaw Gruszka <sgruszka@redhat.com> Acked-by:
Helmut Schaa <helmut.schaa@googlemail.com> Acked-by:
Gertjan van Wingerde <gwingerde@gmail.com> Signed-off-by:
-
Joe Perches authored
Using | with a constant is always true. Likely this should have be &. Signed-off-by:
Joe Perches <joe@perches.com> Acked-by:
Arend van Spriel <arend@broadcom.com> Signed-off-by:
-
Joe Perches authored
Using | with a constant is always true. Likely this should have be &. cc: Ben Greear <greearb@candelatech.com> Signed-off-by:
-
Felix Fietkau authored
Fixes a lockdep warning: =================================================== [ INFO: suspicious rcu_dereference_check() usage. ] --------------------------------------------------- net/mac80211/agg-rx.c:148 invoked rcu_dereference_check() without protection! other info that might help us debug this: rcu_scheduler_active = 1, debug_locks = 1 1 lock held by arecord/11226: #0: (&tid_agg_rx->session_timer){+.-...}, at: [<ffffffff81066bb0>] call_timer_fn+0x0/0x360 stack backtrace: Pid: 11226, comm: arecord Not tainted 3.1.0-kml #16 Call Trace: <IRQ> [<ffffffff81093454>] lockdep_rcu_dereference+0xa4/0xc0 [<ffffffffa02778c9>] sta_rx_agg_session_timer_expired+0xc9/0x110 [mac80211] [<ffffffffa0277800>] ? ieee80211_process_addba_resp+0x220/0x220 [mac80211] [<ffffffff81066c3a>] call_timer_fn+0x8a/0x360 [<ffffffff81066bb0>] ? init_timer_deferrable_key+0x30/0x30 [<ffffffff81477bb0>] ? _raw_spin_unlock_irq+0x30/0x70 [<ffffffff81067049>] run_timer_softirq+0x139/0x310 [<ffffffff81091d5e>] ? put_lock_stats.isra.25+0xe/0x40 [<ffffffff810922ac>] ? lock_release_holdtime.part.26+0xdc/0x160 [<ffffffffa0277800>] ? ieee80211_process_addba_resp+0x220/0x220 [mac80211] [<ffffffff8105cb78>] __do_softirq+0xc8/0x3c0 [<ffffffff8108f088>] ? tick_dev_program_event+0x48/0x110 [<ffffffff8108f16f>] ? tick_program_event+0x1f/0x30 [<ffffffff81153b15>] ? putname+0x35/0x50 [<ffffffff8147a43c>] call_softirq+0x1c/0x30 [<ffffffff81004c55>] do_softirq+0xa5/0xe0 [<ffffffff8105d1ee>] irq_exit+0xae/0xe0 [<ffffffff8147ac6b>] smp_apic_timer_interrupt+0x6b/0x98 [<ffffffff81479ab3>] apic_timer_interrupt+0x73/0x80 <EOI> [<ffffffff8146aac6>] ? free_debug_processing+0x1a1/0x1d5 [<ffffffff81153b15>] ? putname+0x35/0x50 [<ffffffff8146ab2b>] __slab_free+0x31/0x2ca [<ffffffff81477c3a>] ? _raw_spin_unlock_irqrestore+0x4a/0x90 [<ffffffff81253b8f>] ? __debug_check_no_obj_freed+0x15f/0x210 [<ffffffff81097054>] ? lock_release_nested+0x84/0xc0 [<ffffffff8113ec55>] ? kmem_cache_free+0x105/0x250 [<ffffffff81153b15>] ? putname+0x35/0x50 [<ffffffff81153b15>] ? putname+0x35/0x50 [<ffffffff8113ed8f>] kmem_cache_free+0x23f/0x250 [<ffffffff81153b15>] putname+0x35/0x50 [<ffffffff81146d8d>] do_sys_open+0x16d/0x1d0 [<ffffffff81146e10>] sys_open+0x20/0x30 [<ffffffff81478f42>] system_call_fastpath+0x16/0x1b Reported-by:Johannes Berg <johannes.berg@intel.com> Signed-off-by:
Felix Fietkau <nbd@openwrt.org> Signed-off-by:
-
Johannes Berg authored
When any interface goes down, it could be the one that we were doing a remain-on-channel with. We therefore need to cancel the remain-on-channel and flush the related work structs so they don't run after the interface has been removed or even destroyed. It's also possible in this case that an off-channel SKB was never transmitted, so free it if this is the case. Note that this can also happen if the driver finishes the off-channel period without ever starting it. Cc: stable@kernel.org Reported-by:
Nirav Shah <nirav.j2.shah@intel.com> Signed-off-by:
-
Johannes Berg authored
Enforcing interface combinations broke uses of hwsim with multiple virtual interfaces. Advertise that all combinations are possible to fix this. Reported-by:
-
Meenakshi Venkataraman authored
As part of hardware reconfig mac80211 tries to restore the station state to its values before the hardware reconfig, but it only goes to the last-state - 1. Fix this off-by-one error. Cc: stable@kernel.org [3.4] Signed-off-by:
Meenakshi Venkataraman <meenakshi.venkataraman@intel.com> Reviewed-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
-
Johannes Berg authored
Since my commit iwlwifi: use valid TX/RX antenna from hw_params the config values are pure overrides, not the real values for all hardware. Therefore, the EEPROM TX power reading code checks the wrong values, it should check the hw_params values. Cc: stable@kernel.org [3.4] Reviewed-by:
-
Chun-Yeow Yeoh authored
Mesh station that joins an MBSS is reachable using mesh portal with 6 address frame by mesh stations from another MBSS if these two different MBSSes are bridged. However, if the mesh station later moves into the same MBSS of those mesh stations, it is unreachable by mesh stations in the MBSS due to the mpp_paths table is not deleted. A quick fix is to perform mesh_path_lookup, if it is available for the target destination, mpp_path_lookup is not performed. When the mesh station moves back to its original MBSS, the mesh_paths will be deleted once expired. So, it will be reachable using mpp_path_lookup again. Signed-off-by:
Chun-Yeow Yeoh <yeohchunyeow@gmail.com> Signed-off-by:
-
Amitkumar Karwar authored
CFG80211_DEV_WARN_ON() at "net/wireless/ibss.c line 63" is unnecessarily triggered even after successful connection, when cfg80211_ibss_joined() is called by driver inside .join_ibss handler. This patch fixes the problem by changing 'sme_state' in ibss path and having WARN_ON() check for 'sme_state' similar to infra association. Signed-off-by:
Amitkumar Karwar <akarwar@marvell.com> Signed-off-by:
Bing Zhao <bzhao@marvell.com> Signed-off-by:
-
Avinash Patil authored
mwifiex uAP supports NL80211_HIDDEN_SSID_ZERO_LEN type of hidden SSID only. NL80211_HIDDEN_SSID_ZERO_CONTENTS is not supported. Signed-off-by:
Avinash Patil <patila@marvell.com> Signed-off-by:
Kiran Divekar <dkiran@marvell.com> Signed-off-by:
-
Avinash Patil authored
Mark bss_config parameters as invalid before setting AP channel. This prevents from setting invalid parameters while setting AP channel to FW. Signed-off-by:
-
Stanislaw Gruszka authored
commit 133d40f9 Author: Stanislaw Gruszka <sgruszka@redhat.com> Date: Wed Mar 28 16:01:19 2012 +0200 mac80211: do not scan and monitor connection in parallel add bug, which make possible to start a scan and never finish it, so make every new scanning request finish with -EBUSY error. This can happen on code paths where we finish connection monitoring and clear IEEE80211_STA_*_POLL flags, but do not check if scan was deferred. This patch fixes those code paths. Signed-off-by:
-
- 03 Jun, 2012 2 commits
-
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dmLinus Torvalds authored
Pull device-mapper updates from Alasdair G Kergon: "Improve multipath's retrying mechanism in some defined circumstances and provide a simple reserve/release mechanism for userspace tools to access thin provisioning metadata while the pool is in use." * tag 'dm-3.5-changes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm: dm thin: provide userspace access to pool metadata dm thin: use slab mempools dm mpath: allow ioctls to trigger pg init dm mpath: delay retry of bypassed pg dm mpath: reduce size of struct multipath
-
- 02 Jun, 2012 18 commits
-
-
Joe Thornber authored
This patch implements two new messages that can be sent to the thin pool target allowing it to take a snapshot of the _metadata_. This, read-only snapshot can be accessed by userland, concurrently with the live target. Only one metadata snapshot can be held at a time. The pool's status line will give the block location for the current msnap. Since version 0.1.5 of the userland thin provisioning tools, the thin_dump program displays the msnap as follows: thin_dump -m <msnap root> <metadata dev> Available here: https://github.com/jthornber/thin-provisioning-tools Now that userland can access the metadata we can do various things that have traditionally been kernel side tasks: i) Incremental backups. By using metadata snapshots we can work out what blocks have changed over time. Combined with data snapshots we can ensure the data doesn't change while we back it up. A short proof of concept script can be found here: https://github.com/jthornber/thinp-test-suite/blob/master/incremental_backup_example.rb ii) Migration of thin devices from one pool to another. iii) Merging snapshots back into an external origin. iv) Asyncronous replication. Signed-off-by:Joe Thornber <ejt@redhat.com> Signed-off-by:
Alasdair G Kergon <agk@redhat.com>
-
Mike Snitzer authored
Use dedicated caches prefixed with a "dm_" name rather than relying on kmalloc mempools backed by generic slab caches so the memory usage of thin provisioning (and any leaks) can be accounted for independently. Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
-
Mikulas Patocka authored
After the failure of a group of paths, any alternative paths that need initialising do not become available until further I/O is sent to the device. Until this has happened, ioctls return -EAGAIN. With this patch, new paths are made available in response to an ioctl too. The processing of the ioctl gets delayed until this has happened. Instead of returning an error, we submit a work item to kmultipathd (that will potentially activate the new path) and retry in ten milliseconds. Note that the patch doesn't retry an ioctl if the ioctl itself fails due to a path failure. Such retries should be handled intelligently by the code that generated the ioctl in the first place, noting that some SCSI commands should not be retried because they are not idempotent (XOR write commands). For commands that could be retried, there is a danger that if the device rejected the SCSI command, the path could be errorneously marked as failed, and the request would be retried on another path which might fail too. It can be determined if the failure happens on the device or on the SCSI controller, but there is no guarantee that all SCSI drivers set these flags correctly. Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
-
Mike Christie authored
If I/O needs retrying and only bypassed priority groups are available, set the pg_init_delay_retry flag to wait before retrying. If, for example, the reason for the bypass is that the controller is getting reset or there is a firmware upgrade happening, retrying right away would cause a flood of log messages and retries for what could be a few seconds or even several minutes. Signed-off-by:
Mike Christie <michaelc@cs.wisc.edu> Acked-by:
-
Mike Snitzer authored
Move multipath structure's 'lock' and 'queue_size' members to eliminate two 4-byte holes. Also use a bit within a single unsigned int for each existing flag (saves 8-bytes). This allows future flags to be added without each consuming an unsigned int. Signed-off-by:
Hannes Reinecke <hare@suse.de> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds authored
Pull networking updates from David Miller: 1) Make syn floods consume significantly less resources by a) Not pre-COW'ing routing metrics for SYN/ACKs b) Mirroring the device queue mapping of the SYN for the SYN/ACK reply. Both from Eric Dumazet. 2) Fix calculation errors in Byte Queue Limiting, from Hiroaki SHIMODA. 3) Validate the length requested when building a paged SKB for a socket, so we don't overrun the page vector accidently. From Jason Wang. 4) When netlabel is disabled, we abort all IP option processing when we see a CIPSO option. This isn't the right thing to do, we should simply skip over it and continue processing the remaining options (if any). Fix from Paul Moore. 5) SRIOV fixes for the mellanox driver from Jack orgenstein and Marcel Apfelbaum. 6) 8139cp enables the receiver before the ring address is properly programmed, which potentially lets the device crap over random memory. Fix from Jason Wang. 7) e1000/e1000e fixes for i217 RST handling, and an improper buffer address reference in jumbo RX frame processing from Bruce Allan and Sebastian Andrzej Siewior, respectively. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: fec_mpc52xx: fix timestamp filtering mcs7830: Implement link state detection e1000e: fix Rapid Start Technology support for i217 e1000: look into the page instead of skb->data for e1000_tbi_adjust_stats() r8169: call netif_napi_del at errpaths and at driver unload tcp: reflect SYN queue_mapping into SYNACK packets tcp: do not create inetpeer on SYNACK message 8139cp/8139too: terminate the eeprom access with the right opmode 8139cp: set ring address before enabling receiver cipso: handle CIPSO options correctly when NetLabel is disabled net: sock: validate data_len before allocating skb in sock_alloc_send_pskb() bql: Avoid possible inconsistent calculation. bql: Avoid unneeded limit decrement. bql: Fix POSDIFF() to integer overflow aware. net/mlx4_core: Fix obscure mlx4_cmd_box parameter in QUERY_DEV_CAP net/mlx4_core: Check port out-of-range before using in mlx4_slave_cap net/mlx4_core: Fixes for VF / Guest startup flow net/mlx4_en: Fix improper use of "port" parameter in mlx4_en_event net/mlx4_core: Fix number of EQs used in ICM initialisation net/mlx4_core: Fix the slave_id out-of-range test in mlx4_eq_int -
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull straggler x86 fixes from Peter Anvin: "Three groups of patches: - EFI boot stub documentation and the ability to print error messages; - Removal for PTRACE_ARCH_PRCTL for x32 (obsolete interface which should never have been ported, and the port is broken and potentially dangerous.) - ftrace stack corruption fixes. I'm not super-happy about the technical implementation, but it is probably the least invasive in the short term. In the future I would like a single method for nesting the debug stack, however." * 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86, x32, ptrace: Remove PTRACE_ARCH_PRCTL for x32 x86, efi: Add EFI boot stub documentation x86, efi; Add EFI boot stub console support x86, efi: Only close open files in error path ftrace/x86: Do not change stacks in DEBUG when calling lockdep x86: Allow nesting of the debug stack IDT setting x86: Reset the debug_stack update counter ftrace: Use breakpoint method to update ftrace caller ftrace: Synchronize variable setting with breakpoints -
Linus Torvalds authored
This reverts the tty layer change to use per-tty locking, because it's not correct yet, and fixing it will require some more deep surgery. The main revert is d29f3ef3 ("tty_lock: Localise the lock"), but there are several smaller commits that built upon it, they also get reverted here. The list of reverted commits is: fde86d31 - tty: add lockdep annotations 8f6576ad - tty: fix ldisc lock inversion trace d3ca8b64 - pty: Fix lock inversion b1d679af - tty: drop the pty lock during hangup abcefe5f - tty/amiserial: Add missing argument for tty_unlock() fd11b42e - cris: fix missing tty arg in wait_event_interruptible_tty call d29f3ef3 - tty_lock: Localise the lock The revert had a trivial conflict in the 68360serial.c staging driver that got removed in the meantime. Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Stephan Gatzka authored
skb_defer_rx_timestamp was called with a freshly allocated skb but must be called with rskb instead. Signed-off-by:
Stephan Gatzka <stephan@gatzka.org> Cc: stable <stable@vger.kernel.org> Acked-by:
Richard Cochran <richardcochran@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Ondrej Zary authored
Add .status callback that detects link state changes. Tested with MCS7832CV-AA chip (9710:7830, identified as rev.C by the driver). Fixes https://bugzilla.kernel.org/show_bug.cgi?id=28532Signed-off-by:
Ondrej Zary <linux@rainbow-software.org> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/viro/{vfs,signal}Linus Torvalds authored
Pull vfs fix and a fix from the signal changes for frv from Al Viro. The __kernel_nlink_t for powerpc got scrogged because 64-bit powerpc actually depended on the default "unsigned long", while 32-bit powerpc had an explicit override to "unsigned short". Al didn't notice, and made both of them be the unsigned short. The frv signal fix is fallout from simplifying the do_notify_resume() code, and leaving an extra parenthesis. * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: powerpc: Fix size of st_nlink on 64bit * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal: frv: Remove bogus closing parenthesis
-
Anton Blanchard authored
commit e57f93cc (powerpc: get rid of nlink_t uses, switch to explicitly-sized type) changed the size of st_nlink on ppc64 from a long to a short, resulting in boot failures. Signed-off-by:
Anton Blanchard <anton@samba.org> Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk>
-
Geert Uytterhoeven authored
Introduced by commit 6fd84c08 ("TIF_RESTORE_SIGMASK can be set only when TIF_SIGPENDING is set") Signed-off-by:
Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by:
-
Bruce Allan authored
The definition of I217_PROXY_CTRL must use the BM_PHY_REG() macro instead of the PHY_REG() macro for PHY page 800 register 70 since it is for a PHY register greater than the maximum allowed by the latter macro, and fix a typo setting the I217_MEMPWR register in e1000_suspend_workarounds_ich8lan. Also for clarity, rename a few defines as bit definitions instead of masks. Signed-off-by:
Bruce Allan <bruce.w.allan@intel.com> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Sebastian Andrzej Siewior authored
This is another fixup where the data is not transfered into buffer addressed by skb->data but into a page. Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Tested-by:
-
Linus Torvalds authored
Merge fixups for the mac NLS tables from Andrew. * emailed from Andrew Morton, and one cleanup by me: nls: fix (and rename) mac NLS table files and config options fs/nls/Makefile: remove bogus CONFIG_ assignments
-
Linus Torvalds authored
The config options in the Kconfig file (with _CODEPAGE_ in the name) didn't match the config option name in the Makefile (no _CODEPAGE_). And both of them were of the hard-to-read MACXYZZY variety, which made them hard to parse for normal humans: MACROMAN easily reads as "macro man", not as "Mac Roman". So rename the options to be consistent, and be NLS_MAC_xyzzy. Rename the files to be mac-xyzzy.c too, and drop the "nls" part entirely (it's already in the directory name). Signed-off-by: -
Andrew Morton authored
These were debug things which snuck through. Reported-by:
Yinghai Lu <yinghai@kernel.org> Cc: Vladimir Serbinenko <phcoder@gmail.com> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
- 01 Jun, 2012 5 commits
-
-
git://github.com/schandinat/linux-2.6Linus Torvalds authored
Pull fbdev updates from Florian Tobias Schandinat: - driver for AUO-K1900 and AUO-K1901 epaper controller - large updates for OMAP (e.g. decouple HDMI audio and video) - some updates for Exynos and SH Mobile - various other small fixes and cleanups * tag 'fbdev-updates-for-3.5' of git://github.com/schandinat/linux-2.6: (130 commits) video: bfin_adv7393fb: Fix cleanup code video: exynos_dp: reduce delay time when configuring video setting video: exynos_dp: move sw reset prioir to enabling sw defined function video: exynos_dp: use devm_ functions fb: handle NULL pointers in framebuffer release OMAPDSS: HDMI: OMAP4: Update IRQ flags for the HPD IRQ request OMAPDSS: Apply VENC timings even if panel is disabled OMAPDSS: VENC/DISPC: Delay dividing Y resolution for managers connected to VENC OMAPDSS: DISPC: Support rotation through TILER OMAPDSS: VRFB: remove compiler warnings when CONFIG_BUG=n OMAPFB: remove compiler warnings when CONFIG_BUG=n OMAPDSS: remove compiler warnings when CONFIG_BUG=n OMAPDSS: DISPC: fix usage of dispc_ovl_set_accu_uv OMAPDSS: use DSI_FIFO_BUG workaround only for manual update displays OMAPDSS: DSI: Support command mode interleaving during video mode blanking periods OMAPDSS: DISPC: Update Accumulator configuration for chroma plane drivers/video: fsl-diu-fb: don't initialize the THRESHOLDS registers video: exynos mipi dsi: support reverse panel type video: exynos mipi dsi: Properly interpret the interrupt source flags video: exynos mipi dsi: Avoid races in probe() ...
-
git://git.infradead.org/linux-mtdLinus Torvalds authored
Pull mtd update from David Woodhouse: - More robust parsing especially of xattr data in JFFS2 - Updates to mxc_nand and gpmi drivers to support new boards and device tree - Improve consistency of information about ECC strength in NAND devices - Clean up partition handling of plat_nand - Support NAND drivers without dedicated access to OOB area - BCH hardware ECC support for OMAP - Other fixes and cleanups, and a few new device IDs Fixed trivial conflict in drivers/mtd/nand/gpmi-nand/gpmi-nand.c due to added include files next to each other. * tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd: (75 commits) mtd: mxc_nand: move ecc strengh setup before nand_scan_tail mtd: block2mtd: fix recursive call of mtd_writev mtd: gpmi-nand: define ecc.strength mtd: of_parts: fix breakage in Kconfig mtd: nand: fix scan_read_raw_oob mtd: docg3 fix in-middle of blocks reads mtd: cfi_cmdset_0002: Slight cleanup of fixup messages mtd: add fixup for S29NS512P NOR flash. jffs2: allow to complete xattr integrity check on first GC scan jffs2: allow to discriminate between recoverable and non-recoverable errors mtd: nand: omap: add support for hardware BCH ecc ARM: OMAP3: gpmc: add BCH ecc api and modes mtd: nand: check the return code of 'read_oob/read_oob_raw' mtd: nand: remove 'sndcmd' parameter of 'read_oob/read_oob_raw' mtd: m25p80: Add support for Winbond W25Q80BW jffs2: get rid of jffs2_sync_super jffs2: remove unnecessary GC pass on sync jffs2: remove unnecessary GC pass on umount jffs2: remove lock_super mtd: gpmi: add gpmi support for mx6q ...
-
git://cavan.codon.org.uk/platform-drivers-x86Linus Torvalds authored
Pull x86 platform driver updates from Matthew Garrett: "Some significant improvements for the Sony driver on newer machines, but other than that mostly just minor fixes and a patch to remove the broken rfkill code from the Dell driver." * 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86: (35 commits) apple-gmux: Fix up the suspend/resume patch dell-laptop: Remove rfkill code toshiba_acpi: Fix mis-merge dell-laptop: Add touchpad led support for Dell V3450 acer-wmi: add 3 laptops to video backlight vendor mode quirk table sony-laptop: add touchpad enable/disable function sony-laptop: add missing Fn key combos for 0x100 handlers sony-laptop: add support for more WWAN modems sony-laptop: new keyboard backlight handle sony-laptop: add high speed battery charging function sony-laptop: support automatic resume on lid open sony-laptop: adjust error handling in finding SNC handles sony-laptop: add thermal profiles support sony-laptop: support battery care functions sony-laptop: additional debug statements sony-laptop: improve SNC initialization and acpi notify callback code sony-laptop: use kstrtoul to parse sysfs values sony-laptop: generalise ACPI calls into SNC functions sony-laptop: fix return path when no ACPI buffer is allocated sony-laptop: use soft rfkill status stored in hw ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linuxLinus Torvalds authored
Pull slab updates from Pekka Enberg: "Mainly a bunch of SLUB fixes from Joonsoo Kim" * 'slab/for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/penberg/linux: slub: use __SetPageSlab function to set PG_slab flag slub: fix a memory leak in get_partial_node() slub: remove unused argument of init_kmem_cache_node() slub: fix a possible memory leak Documentations: Fix slabinfo.c directory in vm/slub.txt slub: fix incorrect return type of get_any_partial()
-
H. Peter Anvin authored
-
