- 13 Sep, 2014 40 commits
-
-
Christopher Alexander Tobias Schulze authored
[ Upstream commit fe418231 ] Fix detection of BREAK on sunsab serial console: BREAK detection was only performed when there were also serial characters received simultaneously. To handle all BREAKs correctly, the check for BREAK and the corresponding call to uart_handle_break() must also be done if count == 0, therefore duplicate this code fragment and pull it out of the loop over the received characters. Patch applies to 3.16-rc6. Signed-off-by:
Christopher Alexander Tobias Schulze <cat.schulze@alice-dsl.net> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Ben Hutchings <ben@decadent.org.uk>
-
Christopher Alexander Tobias Schulze authored
[ Upstream commit 5cdceab3 ] Fix regression in bbc i2c temperature and fan control on some Sun systems that causes the driver to refuse to load due to the bbc_i2c_bussel resource not being present on the (second) i2c bus where the temperature sensors and fan control are located. (The check for the number of resources was removed when the driver was ported to a pure OF driver in mid 2008.) Signed-off-by:
-
David S. Miller authored
[ Upstream commit 4ca9a237 ] Based almost entirely upon a patch by Christopher Alexander Tobias Schulze. In commit db64fe02 ("mm: rewrite vmap layer") lazy VMAP tlb flushing was added to the vmalloc layer. This causes problems on sparc64. Sparc64 has two VMAP mapped regions and they are not contiguous with eachother. First we have the malloc mapping area, then another unrelated region, then the vmalloc region. This "another unrelated region" is where the firmware is mapped. If the lazy TLB flushing logic in the vmalloc code triggers after we've had both a module unload and a vfree or similar, it will pass an address range that goes from somewhere inside the malloc region to somewhere inside the vmalloc region, and thus covering the openfirmware area entirely. The sparc64 kernel learns about openfirmware's dynamic mappings in this region early in the boot, and then services TLB misses in this area. But openfirmware has some locked TLB entries which are not mentioned in those dynamic mappings and we should thus not disturb them. These huge lazy TLB flush ranges causes those openfirmware locked TLB entries to be removed, resulting in all kinds of problems including hard hangs and crashes during reboot/reset. Besides causing problems like this, such huge TLB flush ranges are also incredibly inefficient. A plea has been made with the author of the VMAP lazy TLB flushing code, but for now we'll put a safety guard into our flush_tlb_kernel_range() implementation. Since the implementation has become non-trivial, stop defining it as a macro and instead make it a function in a C source file. Signed-off-by:
-
David S. Miller authored
[ Upstream commit 18f38132 ] The assumption was that update_mmu_cache() (and the equivalent for PMDs) would only be called when the PTE being installed will be accessible by the user. This is not true for code paths originating from remove_migration_pte(). There are dire consequences for placing a non-valid PTE into the TSB. The TLB miss frramework assumes thatwhen a TSB entry matches we can just load it into the TLB and return from the TLB miss trap. So if a non-valid PTE is in there, we will deadlock taking the TLB miss over and over, never satisfying the miss. Just exit early from update_mmu_cache() and friends in this situation. Based upon a report and patch from Christopher Alexander Tobias Schulze. Signed-off-by:
-
David S. Miller authored
[ Upstream commit 5aa4ecfd ] This is the prevent previous stores from overlapping the block stores done by the memcpy loop. Based upon a glibc patch by Jose E. Marchesi Signed-off-by:
-
David S. Miller authored
[ Upstream commit b18eb2d7 ] Access to the TSB hash tables during TLB misses requires that there be an atomic 128-bit quad load available so that we fetch a matching TAG and DATA field at the same time. On cpus prior to UltraSPARC-III only virtual address based quad loads are available. UltraSPARC-III and later provide physical address based variants which are easier to use. When we only have virtual address based quad loads available this means that we have to lock the TSB into the TLB at a fixed virtual address on each cpu when it runs that process. We can't just access the PAGE_OFFSET based aliased mapping of these TSBs because we cannot take a recursive TLB miss inside of the TLB miss handler without risking running out of hardware trap levels (some trap combinations can be deep, such as those generated by register window spill and fill traps). Without huge pages it's working perfectly fine, but when the huge TSB got added another chunk of fixed virtual address space was not allocated for this second TSB mapping. So we were mapping both the 8K and 4MB TSBs to the same exact virtual address, causing multiple TLB matches which gives undefined behavior. Signed-off-by:
-
David S. Miller authored
[ Upstream commit e5c460f4 ] This was found using Dave Jone's trinity tool. When a user process which is 32-bit performs a load or a store, the cpu chops off the top 32-bits of the effective address before translating it. This is because we run 32-bit tasks with the PSTATE_AM (address masking) bit set. We can't run the kernel with that bit set, so when the kernel accesses userspace no address masking occurs. Since a 32-bit process will have no mappings in that region we will properly fault, so we don't try to handle this using access_ok(), which can safely just be a NOP on sparc64. Real faults from 32-bit processes should never generate such addresses so a bug check was added long ago, and it barks in the logs if this happens. But it also barks when a kernel user access causes this condition, and that _can_ happen. For example, if a pointer passed into a system call is "0xfffffffc" and the kernel access 4 bytes offset from that pointer. Just handle such faults normally via the exception entries. Signed-off-by:
-
David S. Miller authored
[ Upstream commit 70ffc6eb ] Make get_user_insn() able to cope with huge PMDs. Next, make do_fault_siginfo() more robust when get_user_insn() can't actually fetch the instruction. In particular, use the MMU announced fault address when that happens, instead of calling compute_effective_address() and computing garbage. Signed-off-by:
-
David S. Miller authored
[ Upstream commit d037d163 ] If we have a 32-bit task we must chop off the top 32-bits of the 64-bit value just as the cpu would. Signed-off-by:
-
Kirill Tkhai authored
[ Upstream commit 49b6c01f ] One more place where we must not be able to be preempted or to be interrupted in RT. Always actually disable interrupts during synchronization cycle. Signed-off-by:
Kirill Tkhai <tkhai@yandex.ru> Signed-off-by:
-
David S. Miller authored
[ Upstream commit aa3449ee ] Only the second argument, 'op', is signed. Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 757efd32 ] Dave reported following splat, caused by improper use of IP_INC_STATS_BH() in process context. BUG: using __this_cpu_add() in preemptible [00000000] code: trinity-c117/14551 caller is __this_cpu_preempt_check+0x13/0x20 CPU: 3 PID: 14551 Comm: trinity-c117 Not tainted 3.16.0+ #33 ffffffff9ec898f0 0000000047ea7e23 ffff88022d32f7f0 ffffffff9e7ee207 0000000000000003 ffff88022d32f818 ffffffff9e397eaa ffff88023ee70b40 ffff88022d32f970 ffff8801c026d580 ffff88022d32f828 ffffffff9e397ee3 Call Trace: [<ffffffff9e7ee207>] dump_stack+0x4e/0x7a [<ffffffff9e397eaa>] check_preemption_disabled+0xfa/0x100 [<ffffffff9e397ee3>] __this_cpu_preempt_check+0x13/0x20 [<ffffffffc0839872>] sctp_packet_transmit+0x692/0x710 [sctp] [<ffffffffc082a7f2>] sctp_outq_flush+0x2a2/0xc30 [sctp] [<ffffffff9e0d985c>] ? mark_held_locks+0x7c/0xb0 [<ffffffff9e7f8c6d>] ? _raw_spin_unlock_irqrestore+0x5d/0x80 [<ffffffffc082b99a>] sctp_outq_uncork+0x1a/0x20 [sctp] [<ffffffffc081e112>] sctp_cmd_interpreter.isra.23+0x1142/0x13f0 [sctp] [<ffffffffc081c86b>] sctp_do_sm+0xdb/0x330 [sctp] [<ffffffff9e0b8f1b>] ? preempt_count_sub+0xab/0x100 [<ffffffffc083b350>] ? sctp_cname+0x70/0x70 [sctp] [<ffffffffc08389ca>] sctp_primitive_ASSOCIATE+0x3a/0x50 [sctp] [<ffffffffc083358f>] sctp_sendmsg+0x88f/0xe30 [sctp] [<ffffffff9e0d673a>] ? lock_release_holdtime.part.28+0x9a/0x160 [<ffffffff9e0d62ce>] ? put_lock_stats.isra.27+0xe/0x30 [<ffffffff9e73b624>] inet_sendmsg+0x104/0x220 [<ffffffff9e73b525>] ? inet_sendmsg+0x5/0x220 [<ffffffff9e68ac4e>] sock_sendmsg+0x9e/0xe0 [<ffffffff9e1c0c09>] ? might_fault+0xb9/0xc0 [<ffffffff9e1c0bae>] ? might_fault+0x5e/0xc0 [<ffffffff9e68b234>] SYSC_sendto+0x124/0x1c0 [<ffffffff9e0136b0>] ? syscall_trace_enter+0x250/0x330 [<ffffffff9e68c3ce>] SyS_sendto+0xe/0x10 [<ffffffff9e7f9be4>] tracesys+0xdd/0xe2 This is a followup of commits f1d8cba6 ("inet: fix possible seqlock deadlocks") and 7f88c6b2 ("ipv6: fix possible seqlock deadlock in ip6_finish_output2") Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Reported-by:
Dave Jones <davej@redhat.com> Acked-by:
Neil Horman <nhorman@tuxdriver.com> Acked-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
-
Sasha Levin authored
[ Upstream commit 06ebb06d ] Check for cases when the caller requests 0 bytes instead of running off and dereferencing potentially invalid iovecs. Signed-off-by:
Sasha Levin <sasha.levin@oracle.com> Signed-off-by:
-
Vlad Yasevich authored
[ Upstream commit 081e83a7 ] Macvlan devices do not initialize vlan_features. As a result, any vlan devices configured on top of macvlans perform very poorly. Initialize vlan_features based on the vlan features of the lower-level device. Signed-off-by:
Vlad Yasevich <vyasevic@redhat.com> Signed-off-by:
-
Daniel Borkmann authored
[ Upstream commit 1be9a950 ] Jason reported an oops caused by SCTP on his ARM machine with SCTP authentication enabled: Internal error: Oops: 17 [#1] ARM CPU: 0 PID: 104 Comm: sctp-test Not tainted 3.13.0-68744-g3632f30c9b20-dirty #1 task: c6eefa40 ti: c6f52000 task.ti: c6f52000 PC is at sctp_auth_calculate_hmac+0xc4/0x10c LR is at sg_init_table+0x20/0x38 pc : [<c024bb80>] lr : [<c00f32dc>] psr: 40000013 sp : c6f538e8 ip : 00000000 fp : c6f53924 r10: c6f50d80 r9 : 00000000 r8 : 00010000 r7 : 00000000 r6 : c7be4000 r5 : 00000000 r4 : c6f56254 r3 : c00c8170 r2 : 00000001 r1 : 00000008 r0 : c6f1e660 Flags: nZcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user Control: 0005397f Table: 06f28000 DAC: 00000015 Process sctp-test (pid: 104, stack limit = 0xc6f521c0) Stack: (0xc6f538e8 to 0xc6f54000) [...] Backtrace: [<c024babc>] (sctp_auth_calculate_hmac+0x0/0x10c) from [<c0249af8>] (sctp_packet_transmit+0x33c/0x5c8) [<c02497bc>] (sctp_packet_transmit+0x0/0x5c8) from [<c023e96c>] (sctp_outq_flush+0x7fc/0x844) [<c023e170>] (sctp_outq_flush+0x0/0x844) from [<c023ef78>] (sctp_outq_uncork+0x24/0x28) [<c023ef54>] (sctp_outq_uncork+0x0/0x28) from [<c0234364>] (sctp_side_effects+0x1134/0x1220) [<c0233230>] (sctp_side_effects+0x0/0x1220) from [<c02330b0>] (sctp_do_sm+0xac/0xd4) [<c0233004>] (sctp_do_sm+0x0/0xd4) from [<c023675c>] (sctp_assoc_bh_rcv+0x118/0x160) [<c0236644>] (sctp_assoc_bh_rcv+0x0/0x160) from [<c023d5bc>] (sctp_inq_push+0x6c/0x74) [<c023d550>] (sctp_inq_push+0x0/0x74) from [<c024a6b0>] (sctp_rcv+0x7d8/0x888) While we already had various kind of bugs in that area ec0223ec ("net: sctp: fix sctp_sf_do_5_1D_ce to verify if we/peer is AUTH capable") and b14878cc ("net: sctp: cache auth_enable per endpoint"), this one is a bit of a different kind. Giving a bit more background on why SCTP authentication is needed can be found in RFC4895: SCTP uses 32-bit verification tags to protect itself against blind attackers. These values are not changed during the lifetime of an SCTP association. Looking at new SCTP extensions, there is the need to have a method of proving that an SCTP chunk(s) was really sent by the original peer that started the association and not by a malicious attacker. To cause this bug, we're triggering an INIT collision between peers; normal SCTP handshake where both sides intent to authenticate packets contains RANDOM; CHUNKS; HMAC-ALGO parameters that are being negotiated among peers: ---------- INIT[RANDOM; CHUNKS; HMAC-ALGO] ----------> <------- INIT-ACK[RANDOM; CHUNKS; HMAC-ALGO] --------- -------------------- COOKIE-ECHO --------------------> <-------------------- COOKIE-ACK --------------------- RFC4895 says that each endpoint therefore knows its own random number and the peer's random number *after* the association has been established. The local and peer's random number along with the shared key are then part of the secret used for calculating the HMAC in the AUTH chunk. Now, in our scenario, we have 2 threads with 1 non-blocking SEQ_PACKET socket each, setting up common shared SCTP_AUTH_KEY and SCTP_AUTH_ACTIVE_KEY properly, and each of them calling sctp_bindx(3), listen(2) and connect(2) against each other, thus the handshake looks similar to this, e.g.: ---------- INIT[RANDOM; CHUNKS; HMAC-ALGO] ----------> <------- INIT-ACK[RANDOM; CHUNKS; HMAC-ALGO] --------- <--------- INIT[RANDOM; CHUNKS; HMAC-ALGO] ----------- -------- INIT-ACK[RANDOM; CHUNKS; HMAC-ALGO] --------> ... Since such collisions can also happen with verification tags, the RFC4895 for AUTH rather vaguely says under section 6.1: In case of INIT collision, the rules governing the handling of this Random Number follow the same pattern as those for the Verification Tag, as explained in Section 5.2.4 of RFC 2960 [5]. Therefore, each endpoint knows its own Random Number and the peer's Random Number after the association has been established. In RFC2960, section 5.2.4, we're eventually hitting Action B: B) In this case, both sides may be attempting to start an association at about the same time but the peer endpoint started its INIT after responding to the local endpoint's INIT. Thus it may have picked a new Verification Tag not being aware of the previous Tag it had sent this endpoint. The endpoint should stay in or enter the ESTABLISHED state but it MUST update its peer's Verification Tag from the State Cookie, stop any init or cookie timers that may running and send a COOKIE ACK. In other words, the handling of the Random parameter is the same as behavior for the Verification Tag as described in Action B of section 5.2.4. Looking at the code, we exactly hit the sctp_sf_do_dupcook_b() case which triggers an SCTP_CMD_UPDATE_ASSOC command to the side effect interpreter, and in fact it properly copies over peer_{random, hmacs, chunks} parameters from the newly created association to update the existing one. Also, the old asoc_shared_key is being released and based on the new params, sctp_auth_asoc_init_active_key() updated. However, the issue observed in this case is that the previous asoc->peer.auth_capable was 0, and has *not* been updated, so that instead of creating a new secret, we're doing an early return from the function sctp_auth_asoc_init_active_key() leaving asoc->asoc_shared_key as NULL. However, we now have to authenticate chunks from the updated chunk list (e.g. COOKIE-ACK). That in fact causes the server side when responding with ... <------------------ AUTH; COOKIE-ACK ----------------- ... to trigger a NULL pointer dereference, since in sctp_packet_transmit(), it discovers that an AUTH chunk is being queued for xmit, and thus it calls sctp_auth_calculate_hmac(). Since the asoc->active_key_id is still inherited from the endpoint, and the same as encoded into the chunk, it uses asoc->asoc_shared_key, which is still NULL, as an asoc_key and dereferences it in ... crypto_hash_setkey(desc.tfm, &asoc_key->data[0], asoc_key->len) ... causing an oops. All this happens because sctp_make_cookie_ack() called with the *new* association has the peer.auth_capable=1 and therefore marks the chunk with auth=1 after checking sctp_auth_send_cid(), but it is *actually* sent later on over the then *updated* association's transport that didn't initialize its shared key due to peer.auth_capable=0. Since control chunks in that case are not sent by the temporary association which are scheduled for deletion, they are issued for xmit via SCTP_CMD_REPLY in the interpreter with the context of the *updated* association. peer.auth_capable was 0 in the updated association (which went from COOKIE_WAIT into ESTABLISHED state), since all previous processing that performed sctp_process_init() was being done on temporary associations, that we eventually throw away each time. The correct fix is to update to the new peer.auth_capable value as well in the collision case via sctp_assoc_update(), so that in case the collision migrated from 0 -> 1, sctp_auth_asoc_init_active_key() can properly recalculate the secret. This therefore fixes the observed server panic. Fixes: 730fc3d0 ("[SCTP]: Implete SCTP-AUTH parameter processing") Reported-by:
Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by:
Daniel Borkmann <dborkman@redhat.com> Tested-by:
Vlad Yasevich <vyasevich@gmail.com> Signed-off-by:
-
Christoph Paasch authored
[ Upstream commit 1f74e613 ] In vegas we do a multiplication of the cwnd and the rtt. This may overflow and thus their result is stored in a u64. However, we first need to cast the cwnd so that actually 64-bit arithmetic is done. Then, we need to do do_div to allow this to be used on 32-bit arches. Cc: Stephen Hemminger <stephen@networkplumber.org> Cc: Neal Cardwell <ncardwell@google.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Cc: David Laight <David.Laight@ACULAB.COM> Cc: Doug Leith <doug.leith@nuim.ie> Fixes: 8d3a564d (tcp: tcp_vegas cong avoid fix) Signed-off-by:
Christoph Paasch <christoph.paasch@uclouvain.be> Signed-off-by:
-
Christoph Paasch authored
[ Upstream commit 45a07695 ] In veno we do a multiplication of the cwnd and the rtt. This may overflow and thus their result is stored in a u64. However, we first need to cast the cwnd so that actually 64-bit arithmetic is done. A first attempt at fixing 76f10177 ([TCP]: TCP Veno congestion control) was made by 15913114 (tcp: Overflow bug in Vegas), but it failed to add the required cast in tcp_veno_cong_avoid(). Fixes: 76f10177 ([TCP]: TCP Veno congestion control) Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 04ca6973 ] In "Counting Packets Sent Between Arbitrary Internet Hosts", Jeffrey and Jedidiah describe ways exploiting linux IP identifier generation to infer whether two machines are exchanging packets. With commit 73f156a6 ("inetpeer: get rid of ip_id_count"), we changed IP id generation, but this does not really prevent this side-channel technique. This patch adds a random amount of perturbation so that IP identifiers for a given destination [1] are no longer monotonically increasing after an idle period. Note that prandom_u32_max(1) returns 0, so if generator is used at most once per jiffy, this patch inserts no hole in the ID suite and do not increase collision probability. This is jiffies based, so in the worst case (HZ=1000), the id can rollover after ~65 seconds of idle time, which should be fine. We also change the hash used in __ip_select_ident() to not only hash on daddr, but also saddr and protocol, so that ICMP probes can not be used to infer information for other protocols. For IPv6, adds saddr into the hash as well, but not nexthdr. If I ping the patched target, we can see ID are now hard to predict. 21:57:11.008086 IP (...) A > target: ICMP echo request, seq 1, length 64 21:57:11.010752 IP (... id 2081 ...) target > A: ICMP echo reply, seq 1, length 64 21:57:12.013133 IP (...) A > target: ICMP echo request, seq 2, length 64 21:57:12.015737 IP (... id 3039 ...) target > A: ICMP echo reply, seq 2, length 64 21:57:13.016580 IP (...) A > target: ICMP echo request, seq 3, length 64 21:57:13.019251 IP (... id 3437 ...) target > A: ICMP echo reply, seq 3, length 64 [1] TCP sessions uses a per flow ID generator not changed by this patch. Signed-off-by:
Jeffrey Knockel <jeffk@cs.unm.edu> Reported-by:
Jedidiah R. Crandall <crandall@cs.unm.edu> Cc: Willy Tarreau <w@1wt.eu> Cc: Hannes Frederic Sowa <hannes@redhat.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 73f156a6 ] Ideally, we would need to generate IP ID using a per destination IP generator. linux kernels used inet_peer cache for this purpose, but this had a huge cost on servers disabling MTU discovery. 1) each inet_peer struct consumes 192 bytes 2) inetpeer cache uses a binary tree of inet_peer structs, with a nominal size of ~66000 elements under load. 3) lookups in this tree are hitting a lot of cache lines, as tree depth is about 20. 4) If server deals with many tcp flows, we have a high probability of not finding the inet_peer, allocating a fresh one, inserting it in the tree with same initial ip_id_count, (cf secure_ip_id()) 5) We garbage collect inet_peer aggressively. IP ID generation do not have to be 'perfect' Goal is trying to avoid duplicates in a short period of time, so that reassembly units have a chance to complete reassembly of fragments belonging to one message before receiving other fragments with a recycled ID. We simply use an array of generators, and a Jenkin hash using the dst IP as a key. ipv6_select_ident() is put back into net/ipv6/ip6_output.c where it belongs (it is only used from this file) secure_ip_id() and secure_ipv6_id() no longer are needed. Rename ip_select_ident_more() to ip_select_ident_segs() to avoid unnecessary decrement/increment of the number of segments. Signed-off-by:
-
Jonas Bonn authored
commit abdf8b5e upstream. Use of EXPORT_SYMBOL requires inclusion of export.h Signed-off-by:
Jonas Bonn <jonas@southpole.se> Signed-off-by:
-
Ralf Baechle authored
commit ff522058 upstream. This fixes the following issue BUG: using smp_processor_id() in preemptible [00000000] code: kjournald/1761 caller is blast_dcache32+0x30/0x254 Call Trace: [<8047f02c>] dump_stack+0x8/0x34 [<802e7e40>] debug_smp_processor_id+0xe0/0xf0 [<80114d94>] blast_dcache32+0x30/0x254 [<80118484>] r4k_dma_cache_wback_inv+0x200/0x288 [<80110ff0>] mips_dma_map_sg+0x108/0x180 [<80355098>] ide_dma_prepare+0xf0/0x1b8 [<8034eaa4>] do_rw_taskfile+0x1e8/0x33c [<8035951c>] ide_do_rw_disk+0x298/0x3e4 [<8034a3c4>] do_ide_request+0x2e0/0x704 [<802bb0dc>] __blk_run_queue+0x44/0x64 [<802be000>] queue_unplugged.isra.36+0x1c/0x54 [<802beb94>] blk_flush_plug_list+0x18c/0x24c [<802bec6c>] blk_finish_plug+0x18/0x48 [<8026554c>] journal_commit_transaction+0x3b8/0x151c [<80269648>] kjournald+0xec/0x238 [<8014ac00>] kthread+0xb8/0xc0 [<8010268c>] ret_from_kernel_thread+0x14/0x1c Caches in most systems are identical - but not always, so we can't avoid the use of smp_call_function() by just looking at the boot CPU's data, have to fiddle with preemption instead. Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Cc: Markos Chandras <markos.chandras@imgtec.com> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/5835Signed-off-by:
-
Florian Fainelli authored
commit 6c37c958 upstream. cc1: warnings being treated as errors arch/mips/kernel/perf_event_mipsxx.c:166: error: 'counters_per_cpu_to_total' defined but not used make[2]: *** [arch/mips/kernel/perf_event_mipsxx.o] Error 1 make[2]: *** Waiting for unfinished jobs.... It was first introduced by 82091564 [MIPS: perf: Add support for 64-bit perf counters.] in 3.2. Signed-off-by:
Florian Fainelli <florian@openwrt.org> Cc: linux-mips@linux-mips.org Cc: david.daney@cavium.com Patchwork: https://patchwork.linux-mips.org/patch/3357/Signed-off-by:
-
Stefan Kristiansson authored
commit 160d8378 upstream. Prevents build issue with updated toolchain Reported-by:
Jack Thomasson <jkt@moonlitsw.com> Tested-by:
Christian Svensson <blue@cmd.nu> Signed-off-by:
Stefan Kristiansson <stefan.kristiansson@saunalahti.fi> Signed-off-by:
-
Johan Hovold authored
commit 5654699f upstream. Make sure to verify the number of ports requested by subdriver to avoid writing beyond the end of fixed-size array in interface data. The current usb-serial implementation is limited to eight ports per interface but failed to verify that the number of ports requested by a subdriver (which could have been determined from device descriptors) did not exceed this limit. Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.2: s/ddev/\&interface->dev/] Signed-off-by:
-
Johan Hovold authored
commit d979e9f9 upstream. Make sure to verify the maximum number of endpoints per type to avoid writing beyond the end of a stack-allocated array. The current usb-serial implementation is limited to eight ports per interface but failed to verify that the number of endpoints of a certain type reported by a device did not exceed this limit. Signed-off-by:
-
Mark Rutland authored
commit 2c32c65e upstream. On revisions of Cortex-A15 prior to r3p3, a CLREX instruction at PL1 may falsely trigger a watchpoint exception, leading to potential data aborts during exception return and/or livelock. This patch resolves the issue in the following ways: - Replacing our uses of CLREX with a dummy STREX sequence instead (as we did for v6 CPUs). - Removing the clrex code from v7_exit_coherency_flush and derivatives, since this only exists as a minor performance improvement when non-cached exclusives are in use (Linux doesn't use these). Benchmarking on a variety of ARM cores revealed no measurable performance difference with this change applied, so the change is performed unconditionally and no new Kconfig entry is added. Signed-off-by:
Mark Rutland <mark.rutland@arm.com> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> [bwh: Backported to 3.2: - Drop inapplicable changes to arch/arm/include/asm/cacheflush.h and arch/arm/mach-exynos/mcpm-exynos.c] Signed-off-by:
-
Mark Rutland authored
commit 85868313 upstream. The ARMv6 and ARMv7 early abort handlers clear the exclusive monitors upon entry to the kernel, but this is redundant: - We clear the monitors on every exception return since commit 200b812d ("Clear the exclusive monitor when returning from an exception"), so this is not necessary to ensure the monitors are cleared before returning from a fault handler. - Any dummy STREX will target a temporary scratch area in memory, and may succeed or fail without corrupting useful data. Its status value will not be used. - Any other STREX in the kernel must be preceded by an LDREX, which will initialise the monitors consistently and will not depend on the earlier state of the monitors. Therefore we have no reason to care about the initial state of the exclusive monitors when a data abort is taken, and clearing the monitors prior to exception return (as we already do) is sufficient. This patch removes the redundant clearing of the exclusive monitors from the early abort handlers. Signed-off-by:
-
Jiri Kosina authored
commit 844817e4 upstream. The report passed to us from transport driver could potentially be arbitrarily large, therefore we better sanity-check it so that raw_data that we hold in picolcd_pending structure are always kept within proper bounds. Reported-by:
Steven Vittitoe <scvitti@google.com> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> [bwh: Backported to 3.2: adjust filename] Signed-off-by:
-
Jiri Kosina authored
commit c54def7b upstream. The report passed to us from transport driver could potentially be arbitrarily large, therefore we better sanity-check it so that magicmouse_emit_touch() gets only valid values of raw_id. Reported-by:
-
Trond Myklebust authored
commit aee7af35 upstream. In the presence of delegations, we can no longer assume that the state->n_rdwr, state->n_rdonly, state->n_wronly reflect the open stateid share mode, and so we need to calculate the initial value for calldata->arg.fmode using the state->flags. Reported-by:
James Drews <drews@engr.wisc.edu> Fixes: 88069f77 (NFSv41: Fix a potential state leakage when...) Signed-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Stephen Hemminger authored
commit 5b6b80ae upstream. I have a j5 create (JUA210) USB 2 video device and adding it device id to SIS USB video gets it to work. Signed-off-by:
Stephen Hemminger <stephen@networkplumber.org> Signed-off-by:
-
Lv Zheng authored
commit 3afcf2ec upstream. There is a platform refusing to respond QR_EC when SCI_EVT isn't set (Acer Aspire V5-573G). Currently, we rely on the behaviour that the EC firmware can respond something (for example, 0x00 to indicate "no outstanding events") to QR_EC even when SCI_EVT is not set, but the reporter has complained about AC/battery pluging/unpluging and video brightness change delay on that platform. This is because the work item that has issued QR_EC has to wait until timeout in this case, and the _Qxx method evaluation work item queued after QR_EC one is delayed. It sounds reasonable to fix this issue by: 1. Implementing SCI_EVT sanity check before issuing QR_EC in the EC driver's main state machine. 2. Moving QR_EC issuing out of the work queue used by _Qxx evaluation to a seperate IRQ handling thread. This patch fixes this issue using solution 1. By disallowing QR_EC to be issued when SCI_EVT isn't set, we are able to handle such platform in the EC driver's main state machine. This patch enhances the state machine in this way to survive with such malfunctioning EC firmware. Note that this patch can also fix CLEAR_ON_RESUME quirk which also relies on the assumption that the platforms are able to respond even when SCI_EVT isn't set. Fixes: c0d65341 ACPI / EC: Fix race condition in ec_transaction_completed() Link: https://bugzilla.kernel.org/show_bug.cgi?id=82611Reported-and-tested-by:
Alexander Mezin <mezin.alexander@gmail.com> Signed-off-by:
Lv Zheng <lv.zheng@intel.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Benjamin Tissoires authored
commit 5abfe85c upstream. Commit "HID: logitech: perform bounds checking on device_id early enough" unfortunately leaks some errors to dmesg which are not real ones: - if the report is not a DJ one, then there is not point in checking the device_id - the receiver (index 0) can also receive some notifications which can be safely ignored given the current implementation Move out the test regarding the report_id and also discards printing errors when the receiver got notified. Fixes: ad3e14d7Reported-and-tested-by:
Markus Trippelsdorf <markus@trippelsdorf.de> Signed-off-by:
Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by:
-
James Forshaw authored
commit 6817ae22 upstream. This patch fixes a potential security issue in the whiteheat USB driver which might allow a local attacker to cause kernel memory corrpution. This is due to an unchecked memcpy into a fixed size buffer (of 64 bytes). On EHCI and XHCI busses it's possible to craft responses greater than 64 bytes leading a buffer overflow. Signed-off-by:
James Forshaw <forshaw@google.com> Signed-off-by:
-
Jiri Kosina authored
commit 4ab25786 upstream. There are a few very theoretical off-by-one bugs in report descriptor size checking when performing a pre-parsing fixup. Fix those. Reported-by:
Ben Hawkes <hawkes@google.com> Reviewed-by:
-
Jiri Kosina authored
commit ad3e14d7 upstream. device_index is a char type and the size of paired_dj_deivces is 7 elements, therefore proper bounds checking has to be applied to device_index before it is used. We are currently performing the bounds checking in logi_dj_recv_add_djhid_device(), which is too late, as malicious device could send REPORT_TYPE_NOTIF_DEVICE_UNPAIRED early enough and trigger the problem in one of the report forwarding functions called from logi_dj_raw_event(). Fix this by performing the check at the earliest possible ocasion in logi_dj_raw_event(). Reported-by:
-
Jan Kara authored
commit 410dd3cf upstream. We did not check relocated directory in any way when processing Rock Ridge 'CL' tag. Thus a corrupted isofs image can possibly have a CL entry pointing to another CL entry leading to possibly unbounded recursion in kernel code and thus stack overflow or deadlocks (if there is a loop created from CL entries). Fix the problem by not allowing CL entry to point to a directory entry with CL entry (such use makes no good sense anyway) and by checking whether CL entry doesn't point to itself. Reported-by:
Chris Evans <cevans@google.com> Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
-
Mathias Nyman authored
commit 365038d8 upstream. When we manually need to move the TR dequeue pointer we need to set the correct cycle bit as well. Previously we used the trb pointer from the last event received as a base, but this was changed in commit 1f81b6d2 ("usb: xhci: Prefer endpoint context dequeue pointer") to use the dequeue pointer from the endpoint context instead It turns out some Asmedia controllers advance the dequeue pointer stored in the endpoint context past the event triggering TRB, and this messed up the way the cycle bit was calculated. Instead of adding a quirk or complicating the already hard to follow cycle bit code, the whole cycle bit calculation is now simplified and adapted to handle event and endpoint context dequeue pointer differences. Fixes: 1f81b6d2 ("usb: xhci: Prefer endpoint context dequeue pointer") Reported-by:
Maciej Puzio <mx34567@gmail.com> Reported-by:
Evan Langlois <uudruid74@gmail.com> Reviewed-by:
Julius Werner <jwerner@chromium.org> Tested-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Aaro Koskinen authored
commit 60830868 upstream. get_system_type() is not thread-safe on OCTEON. It uses static data, also more dangerous issue is that it's calling cvmx_fuse_read_byte() every time without any synchronization. Currently it's possible to get processes stuck looping forever in kernel simply by launching multiple readers of /proc/cpuinfo: (while true; do cat /proc/cpuinfo > /dev/null; done) & (while true; do cat /proc/cpuinfo > /dev/null; done) & ... Fix by initializing the system type string only once during the early boot. Signed-off-by:
Aaro Koskinen <aaro.koskinen@nsn.com> Reviewed-by:
Markos Chandras <markos.chandras@imgtec.com> Patchwork: http://patchwork.linux-mips.org/patch/7437/Signed-off-by:
James Hogan <james.hogan@imgtec.com> Signed-off-by:
-
Huang Rui authored
commit 2597fe99 upstream. AMD xHC also needs short tx quirk after tested on most of chipset generations. That's because there is the same incorrect behavior like Fresco Logic host. Please see below message with on USB webcam attached on xHC host: [ 139.262944] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk? [ 139.266934] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk? [ 139.270913] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk? [ 139.274937] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk? [ 139.278914] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk? [ 139.282936] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk? [ 139.286915] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk? [ 139.290938] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk? [ 139.294913] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk? [ 139.298917] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk? Reported-by:
Arindam Nath <arindam.nath@amd.com> Tested-by:
Shriraj-Rai P <shriraj-rai.p@amd.com> Signed-off-by:
Huang Rui <ray.huang@amd.com> Signed-off-by:
-
