After the preparational steps the unification was simple.

The linux_prom_pci_registers definition did not look like
it could be unified at first look since the structure is assigned
using prop_getproperty() / of_get_property() so the structure
is assumed to come direct form the prom.

The LINUX_OPPROM_MAGIC was kept even if it is not used by the kernel
on the assumption that userspace may require it.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

It was not used over the whole tree - so drop it.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Align the sparc and sparc64 versions so differences are minimal.
A few data types are changed to better reflect there actual usage.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

It is not used anywhere in the tree so drop it.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Looks like leftovers from the removal of the special ebus layer.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Trivial unification where the sparc64 specific
parts are protected using a signle ifdef/endif pair.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The two ptrace.h implementations are very alike but
the small differences required two set of ifdef/else/endif pairs.

The definition of reg_window32 could have been shared but
that would have required several updates in sparc32 code as
all printk formatting for example assume it is longs.

sparc_stackf looked like anohter candidate to share if the 32
bit was renamed to sparc_stackf32.
But it contains two pointers in the sparc32 version which would
have been 64 bit in the sparc64 version so it was non-trivial.
Using a set of accessor macros could do the trick if pursued later.

The sparc64 specific definitions are not protected by
ifdef - as it should not be required to do so.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

With the renamed types in place the unification was straightforward.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Renaming a few types to contain a 32 suffix makes the
type names compatible with sparc64 and thus makes sharing
between the two a lot easier.

Note: None of these definitions are expected part of the
stable ABI towards userspace.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

They were almost identical and with the preapration
patch nothing was needed to be added.

The unified version contains a few sparc64 only definitions
but they are kept as is and not protected by ifdef/endif.
The unified version exports a bit more to userspace then the
32 bit version did.
This is not considered fatal.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

o add a sparc32 only definition
o fix a few style issues (white space errors etc).
o include compiler.h (for __user)
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Noticed by Geert Uytterhoeven.
Signed-off-by: David S. Miller <davem@davemloft.net>

To my suprise struct stat64 was not equal on sparc 32 and sparc64,
so there was really nothing to share here.
Unify the files by adding their respective content to stat.h.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Like sparc64 use proper types in struct stat
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

sparc32 does not define __ARCH_WANT_OLD_STAT so
we do not use this structure neither do we support it.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The posix types differed so much in their definition
that they are kept in separate blocks.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to define a config symbol if
it is never set to any value. Undefined symbols equal
to 'n'.

GENERIC_GPIO looks like it is similar but
it is set using select in some other file so
it must be kept.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

GCC 3.0 and 3.1 are too old to build a working kernel.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
[ This check got dropped as obsolete when I simplified the gcc header
  inclusion mess in f153b821, but Willy
  Tarreau reports actually having those old versions still..  -Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'cpus4096-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'cpus4096-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (66 commits)
  x86: export vector_used_by_percpu_irq
  x86: use logical apicid in x2apic_cluster's x2apic_cpu_mask_to_apicid_and()
  sched: nominate preferred wakeup cpu, fix
  x86: fix lguest used_vectors breakage, -v2
  x86: fix warning in arch/x86/kernel/io_apic.c
  sched: fix warning in kernel/sched.c
  sched: move test_sd_parent() to an SMP section of sched.h
  sched: add SD_BALANCE_NEWIDLE at MC and CPU level for sched_mc>0
  sched: activate active load balancing in new idle cpus
  sched: bias task wakeups to preferred semi-idle packages
  sched: nominate preferred wakeup cpu
  sched: favour lower logical cpu number for sched_mc balance
  sched: framework for sched_mc/smt_power_savings=N
  sched: convert BALANCE_FOR_xx_POWER to inline functions
  x86: use possible_cpus=NUM to extend the possible cpus allowed
  x86: fix cpu_mask_to_apicid_and to include cpu_online_mask
  x86: update io_apic.c to the new cpumask code
  x86: Introduce topology_core_cpumask()/topology_thread_cpumask()
  x86: xen: use smp_call_function_many()
  x86: use work_on_cpu in x86/kernel/cpu/mcheck/mce_amd_64.c
  ...

Fixed up trivial conflict in kernel/time/tick-sched.c manually

* 'kvm-updates/2.6.29' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm: (140 commits)
  KVM: MMU: handle large host sptes on invlpg/resync
  KVM: Add locking to virtual i8259 interrupt controller
  KVM: MMU: Don't treat a global pte as such if cr4.pge is cleared
  MAINTAINERS: Maintainership changes for kvm/ia64
  KVM: ia64: Fix kvm_arch_vcpu_ioctl_[gs]et_regs()
  KVM: x86: Rework user space NMI injection as KVM_CAP_USER_NMI
  KVM: VMX: Fix pending NMI-vs.-IRQ race for user space irqchip
  KVM: fix handling of ACK from shared guest IRQ
  KVM: MMU: check for present pdptr shadow page in walk_shadow
  KVM: Consolidate userspace memory capability reporting into common code
  KVM: Advertise the bug in memory region destruction as fixed
  KVM: use cpumask_var_t for cpus_hardware_enabled
  KVM: use modern cpumask primitives, no cpumask_t on stack
  KVM: Extract core of kvm_flush_remote_tlbs/kvm_reload_remote_mmus
  KVM: set owner of cpu and vm file operations
  anon_inodes: use fops->owner for module refcount
  x86: KVM guest: kvm_get_tsc_khz: return khz, not lpj
  KVM: MMU: prepopulate the shadow on invlpg
  KVM: MMU: skip global pgtables on sync due to cr3 switch
  KVM: MMU: collapse remote TLB flushes on root sync
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (32 commits)
  ide-atapi: start dma in a drive-specific way
  ide-atapi: put the rest of non-ide-cd code into the else-clause of ide_transfer_pc
  ide-atapi: remove timeout arg to ide_issue_pc
  ide-cd: remove handler wrappers
  ide-cd: remove xferlen arg to cdrom_start_packet_command
  ide-atapi: split drive-specific functionality in ide_issue_pc
  ide-atapi: assign expiry and timeout based on device type
  ide-atapi: compute cmd_len based on device type in ide_transfer_pc
  ide: remove the last ide-scsi remnants
  ide-atapi: remove ide-scsi remnants from ide_pc_intr()
  ide-atapi: remove ide-scsi remnants from ide_transfer_pc()
  ide-atapi: remove ide-scsi remnants from ide_issue_pc
  ide-cd: move cdrom_timer_expiry to ide-atapi.c
  ide-atapi: teach ide atapi about drive->waiting_for_dma
  ide-atapi: accomodate transfer length calculation for ide-cd
  ide-atapi: setup dma for ide-cd
  ide-atapi: combine drive-specific assignments
  ide-atapi: add a dev_is_idecd-inline
  remove ide-scsi
  ide-floppy: allocate only toplevel packet commands
  ...

* 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/dvrabel/uwb: (31 commits)
  uwb: remove beacon cache entry after calling uwb_notify()
  uwb: remove unused include/linux/uwb/debug.h
  uwb: use print_hex_dump()
  uwb: use dev_dbg() for debug messages
  uwb: fix memory leak in uwb_rc_notif()
  wusb: fix oops when terminating a non-existant reservation
  uwb: fix oops when terminating an already terminated reservation
  uwb: improved MAS allocator and reservation conflict handling
  wusb: add debug files for ASL, PZL and DI to the whci-hcd driver
  uwb: fix oops in debug PAL's reservation callback
  uwb: clean up whci_wait_for() timeout error message
  wusb: whci-hcd shouldn't do ASL/PZL updates while channel is inactive
  uwb: remove unused beacon group join/leave events
  wlp: start/stop radio on network interface up/down
  uwb: add basic radio manager
  uwb: add pal parameter to new reservation callback
  uwb: fix races between events and neh timers
  uwb: don't unbind the radio controller driver when resetting
  uwb: per-radio controller event thread and beacon cache
  uwb: add commands to add/remove IEs to the debug interface
  ...

Ben Herrenschmidt is taking over as the primary powerpc architecture
maintainer.  I'll still be around as his backup/deputy.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* i8k-updates:
  i8k: Add Dell Vostro systems
  i8k: Enable i8k on Dell Precision Systems

This trivial patch adds support for i8k on the new Dell Vostro models.
I tested it on my Vostro 1400, and it works. It does print a warning
when loading the module:

	i8k: unable to get SMM BIOS version

But I couldn't figure out how to fix that. The module seems to work fine,
anyway...
Signed-off-by: Federico Heinz <fheinz@vialibre.org.ar>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Patch to enable i8k on Dell Precisions.
Signed-off-by: Andy Spencer <spenceal@rose-hulman.edu>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Ingo Brueckl <ib@wupperonline.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* tty-updates: (75 commits)
  serial_8250: support for Sealevel Systems Model 7803 COMM+8
  hso maintainers update patch
  hso modem detect fix patch against Alan Cox'es tty tree
  tty: Fix an ircomm warning and note another bug
  drivers/char/cyclades.c: cy_pci_probe: fix error path
  Serial: UART driver changes for Cavium OCTEON.
  Serial: Allow port type to be specified when calling serial8250_register_port.
  8250: Serial driver changes to support future Cavium OCTEON serial patches.
  8250: Don't clobber spinlocks.
  fix for tty-serial-move-port
  tty: We want the port object to be persistent
  __FUNCTION__ is gcc-specific, use __func__
  serial: RS485 ioctl structure uses __u32 include linux/types.h
  tty: Drop the lock_kernel in the private ioctl hook
  synclink_cs: Convert to tty_port
  tty: use port methods for the rocket driver
  tty: kref the rocket driver
  tty: make rocketport use standard port->flags
  tty: Redo the rocket driver locking
  tty: Make epca use the port helpers
  ...

Add support for Sealevel Systems Model 7803 COMM+8
Signed-off-by: Flavio Leitner <fleitner@redhat.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Added D.J. Barrow as maintainer of hso driver.
Signed-off-by: Denis Joseph Barrow <D.Barow@option.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fixed incorrect check for the modem port, this prevents
crashes caused by issueing a tiocmget_submit_urb
on endpoints which don't exist for non modem devices.
Signed-off-by: Denis Joseph Barrow <D.Barow@option.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Roel Kluin noted that line is unsigned so one test is unneccessary. Also
add a warning for another flaw I noticed while making this change.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

We forgot to release resources in one case.

Addresses http://bugzilla.kernel.org/show_bug.cgi?id=12137Reported-by: Florian Lohoff <flo@rfc822.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Cavium UART implementation is not covered by existing uart_configS.
Define a new uart_config (PORT_OCTEON) which is specified by OCTEON
platform device registration code.
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add flag value UPF_FIXED_TYPE which specifies that the UART type is
known and should not be probed.  For this case the UARTs properties
are just copied out of the uart_config entry.

This allows us to keep SOC specific 8250 probe code out of 8250.c.  In
this case we know the serial hardware will not be changing as it is on
the same silicon as the CPU, and we can specify it with certainty in
the board/cpu setup code.

The alternative is to load up 8250.c with a bunch of OCTEON specific
special cases in the probing code.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In order to use Cavium OCTEON specific serial i/o drivers, we first
patch the 8250 driver to use replaceable I/O functions.  Compatible
I/O functions are added for existing iotypeS.

An added benefit of this change is that it makes it easy to factor
some of the existing special cases out to board/SOC specific support
code.

The alternative is to load up 8250.c with a bunch of OCTEON specific
iotype code and bug work-arounds.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In serial8250_isa_init_ports(), the port's lock is initialized.  We
should not overwrite it.  In early_serial_setup(), only copy in the
fields we need.  Since the early console code only uses a subset of
the fields, these are sufficient.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Tomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Hi Alan

next-20081204 crashes with the following message:

BUG: unable to handle kernel paging request at ffff88007d320248
IP: [<ffffffff803de934>] uart_remove_one_port+0xef/0x111
                kfree(info);
     393:       49 8d 7d 10             lea    0x10(%r13),%rdi
     397:       e8 00 00 00 00          callq  39c <uart_remove_one_port+0xef>
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Move the tty_port and uart_info bits around a little. By embedding the uart_info
into the uart_port we get rid of lots of corner case testing and also get the
ability to go port<->state<->info which is a bit more elegant than the current
data structures.

Downsides - we allocate a tiny bit more memory for unused ports, upside we've
removed as much code as it saved for most users..
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>