The worker always touches both netdevs. It is ethernet core and not MAC
specific. We only need one worker, which belongs into the ethernets core
struct.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver supports 2 MACs. Both run on the same DMA ring. If we hit a TX
timeout we need to stop both netdevs before restarting them again. If we
don't do this, mtk_stop() wont shutdown DMA and the consecutive call to
mtk_open() wont restart DMA and enable IRQs.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Inside the TX path there is a lock inside the tx_map function. This is
however too late. The patch moves the lock to the start of the xmit
function right before the free count check of the DMA ring happens.
If we do not do this, the code becomes racy leading to TX stalls and
dropped packets. This happens as there are 2 netdevs running on the
same physical DMA ring.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver supports 2 MACs. Both run on the same DMA ring. If we go
above/below the TX rings threshold value, we always need to wake/stop
the queue of both devices. Not doing to can cause TX stalls and packet
drops on one of the devices.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

HW reset is triggered in the mtk_hw_init() function. There is no need to
also reset the core during probe.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The code used to also support the PDMA engine, which had 2 packet pointers
per descriptor. Because of this we had to divide the result by 2 and round
it up. This is no longer needed as the code only supports QDMA.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The original commit failed to set watchdog_timeo. This patch sets
watchdog_timeo to HZ.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter updates for net-next

The following patchset contains the first batch of Netfilter updates for
your net-next tree.

1) Define pr_fmt() in nf_conntrack, from Weongyo Jeong.

2) Define and register netfilter's afinfo for the bridge family,
   this comes in preparation for native nfqueue's bridge for nft,
   from Stephane Bryant.

3) Add new attributes to store layer 2 and VLAN headers to nfqueue,
   also from Stephane Bryant.

4) Parse new NFQA_VLAN and NFQA_L2HDR nfqueue netlink attributes
   coming from userspace, from Stephane Bryant.

5) Use net->ipv6.devconf_all->hop_limit instead of hardcoded hop_limit
   in IPv6 SYNPROXY, from Liping Zhang.

6) Remove unnecessary check for dst == NULL in nf_reject_ipv6,
   from Haishuang Yan.

7) Deinline ctnetlink event report functions, from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Not performance critical, it is only invoked when an expectation is
added/destroyed.

While at it, kill unused nf_ct_expect_event() wrapper.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Way too large; move it to nf_conntrack_ecache.c.
Reduces total object size by 1216 byte on my machine.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next

Johan Hedberg says:

====================
pull request: bluetooth-next 2016-04-12

Here's a set of Bluetooth & 802.15.4 patches intended for the 4.7 kernel:

 - Fix for race condition in vhci driver
 - Memory leak fix for ieee802154/adf7242 driver
 - Improvements to deal with single-mode (LE-only) Bluetooth controllers
 - Fix for allowing the BT_SECURITY_FIPS security level
 - New BCM2E71 ACPI ID
 - NULL pointer dereference fix fox hci_ldisc driver

Let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

MDIO devices can be stacked upon each other. The current code supports
two levels, which until recently has been enough for a DSA mdio bus on
top of another bus. Now we have hardware which has an MDIO mux in the
middle.

Define an MDIO MUTEX class with three levels.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

David Howells says:

====================
RxRPC: 2nd rewrite part 1

Okay, I'm in the process of rewriting the RxRPC rewrite.  The primary aim of
this second rewrite is to strictly control the number of active connections we
know about and to get rid of connections we don't need much more quickly.

On top of this, there are fixes to the protocol handling which will all occur
in later parts.

Here's the first set of patches from the second go, aimed at net-next.  These
are all fixes and cleanups preparatory to the main event.

Notable parts of this set include:

 (1) A fix for the AFS filesystem to wait for outstanding calls to complete
     before closing the RxRPC socket.

 (2) Differentiation of local and remote abort codes.  At a future point
     userspace will get to see this via control message data on recvmsg().

 (3) Absorb the rxkad module into the af_rxrpc module to prevent a dependency
     loop.

 (4) Create a null security module and unconditionalise calls into the
     security module that's in force (there will always be a security module
     applied to a connection, even if it's just the null one).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Create a null security type for security index 0 and get rid of all
conditional calls to the security operations.  We expect normally to be
using security, so this should be of little negative impact.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Absorb the rxkad security module into the af_rxrpc module so that there's
only one module file.  This avoids a circular dependency whereby rxkad pins
af_rxrpc and cached connections pin rxkad but can't be manually evicted
(they will expire eventually and cease pinning).

With this change, af_rxrpc can just be unloaded, despite having cached
connections.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't assume transport address family and size when using the peer address
to send a packet.  Instead, use the start of the transport address rather
than any particular element of the union and use the transport address
length noted inside the sockaddr_rxrpc struct.

This will be necessary when IPv6 support is introduced.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't pass gfp around in incoming call handling functions, but rather hard
code it at the points where we actually need it since the value comes from
within the rxrpc driver and is always the same.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the rxrpc_connection and rxrpc_call structs, there's one field to hold
the abort code, no matter whether that value was generated locally to be
sent or was received from the peer via an abort packet.

Split the abort code fields in two for cleanliness sake and add an error
field to hold the Linux error number to the rxrpc_call struct too
(sometimes this is generated in a context where we can't return it to
userspace directly).

Furthermore, add a skb mark to indicate a packet that caused a local abort
to be generated so that recvmsg() can pick up the correct abort code.  A
future addition will need to be to indicate to userspace the difference
between aborts via a control message.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Static arrays of strings should be const char *const[].
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move some miscellaneous bits out into their own file to make it easier to
split the call handling.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Disable a debugging statement that has been left enabled
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The afs filesystem needs to wait for any outstanding asynchronous calls
(such as FS.GiveUpCallBacks cleaning up the callbacks lodged with a server)
to complete before closing the AF_RXRPC socket when unloading the module.

This may occur if the module is removed too quickly after unmounting all
filesystems.  This will produce an error report that looks like:

	AFS: Assertion failed
	1 == 0 is false
	0x1 == 0x0 is false
	------------[ cut here ]------------
	kernel BUG at ../fs/afs/rxrpc.c:135!
	...
	RIP: 0010:[<ffffffffa004111c>] afs_close_socket+0xec/0x107 [kafs]
	...
	Call Trace:
	 [<ffffffffa004a160>] afs_exit+0x1f/0x57 [kafs]
	 [<ffffffff810c30a0>] SyS_delete_module+0xec/0x17d
	 [<ffffffff81610417>] entry_SYSCALL_64_fastpath+0x12/0x6b
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Willem de Bruijn says:

====================
net: fix udp pull header breakage

Commit e6afc8ac ("udp: remove headers from UDP packets before
queueing") modified udp receive processing to pull headers before
enqueue and to not expect them on dequeue.

The patch missed protocols on top of udp with in-kernel
implementations that have their own skb_recv_datagram calls and
dequeue logic. Modify these datapaths to also no longer expect
a udp header at skb->data.

Sunrpc and rxrpc are the only two protocols that call this
function and contain references to udphr (some others, like tipc,
are based on encap_rcv, which acts before enqueue, before the
the header pull).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit e6afc8ac modified the udp receive path by pulling the udp
header before queuing an skbuff onto the receive queue.

Rxrpc also calls skb_recv_datagram to dequeue an skb from a udp
socket. Modify this receive path to also no longer expect udp
headers.

Fixes: e6afc8ac ("udp: remove headers from UDP packets before queueing")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit e6afc8ac modified the udp receive path by pulling the udp
header before queuing an skbuff onto the receive queue.

Sunrpc also calls skb_recv_datagram to dequeue an skb from a udp
socket. Modify this receive path to also no longer expect udp
headers.

Fixes: e6afc8ac ("udp: remove headers from UDP packets before queueing")
Reported-by: Franklin S Cooper Jr. <fcooper@ti.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Multipath route lookups should consider knowledge about next hops and not
select a hop that is known to be failed.

Example:

                     [h2]                   [h3]   15.0.0.5
                      |                      |
                     3|                     3|
                    [SP1]                  [SP2]--+
                     1  2                   1     2
                     |  |     /-------------+     |
                     |   \   /                    |
                     |     X                      |
                     |    / \                     |
                     |   /   \---------------\    |
                     1  2                     1   2
         12.0.0.2  [TOR1] 3-----------------3 [TOR2] 12.0.0.3
                     4                         4
                      \                       /
                        \                    /
                         \                  /
                          -------|   |-----/
                                 1   2
                                [TOR3]
                                  3|
                                   |
                                  [h1]  12.0.0.1

host h1 with IP 12.0.0.1 has 2 paths to host h3 at 15.0.0.5:

    root@h1:~# ip ro ls
    ...
    12.0.0.0/24 dev swp1  proto kernel  scope link  src 12.0.0.1
    15.0.0.0/16
            nexthop via 12.0.0.2  dev swp1 weight 1
            nexthop via 12.0.0.3  dev swp1 weight 1
    ...

If the link between tor3 and tor1 is down and the link between tor1
and tor2 then tor1 is effectively cut-off from h1. Yet the route lookups
in h1 are alternating between the 2 routes: ping 15.0.0.5 gets one and
ssh 15.0.0.5 gets the other. Connections that attempt to use the
12.0.0.2 nexthop fail since that neighbor is not reachable:

    root@h1:~# ip neigh show
    ...
    12.0.0.3 dev swp1 lladdr 00:02:00:00:00:1b REACHABLE
    12.0.0.2 dev swp1  FAILED
    ...

The failed path can be avoided by considering known neighbor information
when selecting next hops. If the neighbor lookup fails we have no
knowledge about the nexthop, so give it a shot. If there is an entry
then only select the nexthop if the state is sane. This is similar to
what fib_detect_death does.

To maintain backward compatibility use of the neighbor information is
based on a new sysctl, fib_multipath_use_neigh.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>

Grygorii Strashko says:

====================
drivers: net: cpsw: fix ale calls and drop host_port field from cpsw_priv

This clean up series intended to:
 - fix port_mask parameters in ale calls and drop unnecessary shifts
 - drop host_port field from struct cpsw_priv
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The host_port field is constantly assigned to 0 and this value has
never changed (since time when cpsw driver was introduced. More over,
if this field will be assigned to non 0 value it will break current
driver functionality.

Hence, there are no reasons to continue maintaining this host_port
field and it can be removed, and the HOST_PORT_NUM and ALE_PORT_HOST
defines can be used instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ALE APIs expect to receive port masks as input values for arguments
port_mask, untag, reg_mcast, unreg_mcast. But there are few places in
code where port masks are passed left-shifted by cpsw_priv->host_port,
like below:

 cpsw_ale_add_vlan(priv->ale, priv->data.default_vlan,
		  ALE_ALL_PORTS << priv->host_port,
		  ALE_ALL_PORTS << priv->host_port, 0, 0);

and cpsw is still working just because priv->host_port == 0
and has never ever been changed.

Hence, fix port_mask parameters in ALE APIs calls and drop
"<< priv->host_port" from all places where it's used to
shift valid port mask.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The protocol is 16bit, not 32bit.

Fixes: e1e5314d ("vxlan: implement GPE")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the function resource_size instead of explicit computation.

Problem found using Coccinelle.
Signed-off-by: Vaishali Thakkar <vaishali.thakkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: Update for net-next

Misc. changes for link speed and VF MAC address change.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

On some dual port cards, link speeds on both ports have to be compatible.
Firmware will inform the driver when a certain speed is no longer
supported if the other port has linked up at a certain speed.  Add
logic to handle this event by logging a message and getting the
updated list of supported speeds.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some hypervisors (e.g. ESX) require the VF MAC address to be forwarded to
the PF for approval.  In Linux PF, the call is not forwarded and the
firmware will simply check and approve the MAC address if the PF has not
previously administered a valid MAC address for this VF.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Let firmware know that the driver is giving up control of the link so that
it can be shutdown if no management firmware is running.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

10GBaseT devices must autonegotiate to determine master/slave clocking.
Disallow forced speed in ethtool .set_settings() for these devices.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-next-for-davem-2016-04-11' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers patches for 4.7

Major changes:

iwlwifi

* support for Link Quality measurement
* more work 9000 devices and MSIx
* continuation of the Dynamic Queue Allocation work
* make the paging less memory hungry
* 9000 new Rx path
* removal of IWLWIFI_UAPSD Kconfig option

ath10k

* implement push-pull tx model using mac80211 software queuing support
* enable scan in AP mode (NL80211_FEATURE_AP_SCAN)

wil6210

* add basic PBSS (Personal Basic Service Set) support
* add initial P2P support
* add oob_mode module parameter
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

verifier is using the following structure to track the state of registers:
struct reg_state {
    enum bpf_reg_type type;
    union {
        int imm;
        struct bpf_map *map_ptr;
    };
};
and later on in states_equal() does memcmp(&old->regs[i], &cur->regs[i],..)
to find equivalent states.
Throughout the code of verifier there are assignements to 'imm' and 'map_ptr'
fields and it's not obvious that most of the assignments into 'imm' don't
need to clear extra 4 bytes (like mark_reg_unknown_value() does) to make sure
that memcmp doesn't go over junk left from 'map_ptr' assignment.

Simplify the code by converting 'int' into 'long'
Suggested-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

A stupid refactoring bug in inet6_lookup_listener() needs to be fixed
in order to get proper SO_REUSEPORT behavior.

Fixes: 3b24d854 ("tcp/dccp: do not touch listener sk_refcnt under synflood")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>