- 12 Nov, 2019 40 commits
-
-
Jon Bloomfield authored
commit 4f7af194 upstream. For Gen7, the original cmdparser motive was to permit limited use of register read/write instructions in unprivileged BB's. This worked by copying the user supplied bb to a kmd owned bb, and running it in secure mode, from the ggtt, only if the scanner finds no unsafe commands or registers. For Gen8+ we can't use this same technique because running bb's from the ggtt also disables access to ppgtt space. But we also do not actually require 'secure' execution since we are only trying to reduce the available command/register set. Instead we will copy the user buffer to a kmd owned read-only bb in ppgtt, and run in the usual non-secure mode. Note that ro pages are only supported by ppgtt (not ggtt), but luckily that's exactly what we need. Add the required paths to map the shadow buffer to ppgtt ro for Gen8+ v2: IS_GEN7/IS_GEN (Mika) v3: rebase v4: rebase v5: rebase Signed-off-by:
Jon Bloomfield <jon.bloomfield@intel.com> Cc: Tony Luck <tony.luck@intel.com> Cc: Dave Airlie <airlied@redhat.com> Cc: Takashi Iwai <tiwai@suse.de> Cc: Tyler Hicks <tyhicks@canonical.com> Signed-off-by:
Mika Kuoppala <mika.kuoppala@linux.intel.com> Reviewed-by:
Chris Wilson <chris.p.wilson@intel.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Jon Bloomfield authored
commit 311a50e7 upstream. The existing cmdparser for gen7 can be bypassed by specifying batch_len=0 in the execbuf call. This is safe because bypassing simply reduces the cmd-set available. In a later patch we will introduce cmdparsing for gen9, as a security measure, which must be strictly enforced since without it we are vulnerable to DoS attacks. Introduce the concept of 'required' cmd parsing that cannot be bypassed by submitting zero-length bb's. v2: rebase (Mika) v2: rebase (Mika) v3: fix conflict on engine flags (Mika) Signed-off-by:
-
Jon Bloomfield authored
commit 66d8aba1 upstream. The previous patch has killed support for secure batches on gen6+, and hence the cmdparsers master tables are now dead code. Remove them. Signed-off-by:
-
Jon Bloomfield authored
commit 44157641 upstream. Retroactively stop reporting support for secure batches through the api for gen6+ so that older binaries trigger the fallback path instead. Older binaries use secure batches pre gen6 to access resources that are not available to normal usermode processes. However, all known userspace explicitly checks for HAS_SECURE_BATCHES before relying on the secure batch feature. Since there are no known binaries relying on this for newer gens we can kill secure batches from gen6, via I915_PARAM_HAS_SECURE_BATCHES. v2: rebase (Mika) v3: rebase (Mika) Signed-off-by:
-
Jon Bloomfield authored
commit 0a2f661b upstream. We're about to introduce some new tables for later gens, and the current naming for the gen7 tables will no longer make sense. v2: rebase Signed-off-by:
-
Stefano Garzarella authored
[ Upstream commit ad8a7220 ] The "42f5cda5" commit rightly set SOCK_DONE on peer shutdown, but there is an issue if we receive the SHUTDOWN(RDWR) while the virtio_transport_close_timeout() is scheduled. In this case, when the timeout fires, the SOCK_DONE is already set and the virtio_transport_close_timeout() will not call virtio_transport_reset() and virtio_transport_do_close(). This causes that both sockets remain open and will never be released, preventing the unloading of [virtio|vhost]_transport modules. This patch fixes this issue, calling virtio_transport_reset() and virtio_transport_do_close() when we receive the SHUTDOWN(RDWR) and there is nothing left to read. Fixes: 42f5cda5 ("vsock/virtio: set SOCK_DONE on peer shutdown") Cc: Stephen Barber <smbarber@chromium.org> Signed-off-by:
Stefano Garzarella <sgarzare@redhat.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Steve Moskovchenko authored
[ Upstream commit 1615fe41 ] The MPU6050 driver has recently gained support for the ICM20602 IMU, which is very similar to MPU6xxx. However, the ICM20602's FIFO data specifically includes temperature readings, which were not present on MPU6xxx parts. As a result, the driver will under-read the ICM20602's FIFO register, causing the same (partial) sample to be returned for all reads, until the FIFO overflows. Fix this by adding a table of scan elements specifically for the ICM20602, which takes the extra temperature data into consideration. While we're at it, fix the temperature offset and scaling on ICM20602, since it uses different scale/offset constants than the rest of the MPU6xxx devices. Signed-off-by:
Steve Moskovchenko <stevemo@skydio.com> Fixes: 22904bdf ("iio: imu: mpu6050: Add support for the ICM 20602 IMU") Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit f75359f3 ] Add a couple of READ_ONCE() and WRITE_ONCE() to prevent load-tearing and store-tearing in sock_read_timestamp() and sock_write_timestamp() This might prevent another KCSAN report. Fixes: 3a0ed3e9 ("sock: Make sock->sk_stamp thread-safe") Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Deepa Dinamani <deepa.kernel@gmail.com> Acked-by:
Deepa Dinamani <deepa.kernel@gmail.com> Signed-off-by:
-
Stefano Brivio authored
[ Upstream commit 97664bc2 ] Same as commit 1b4a7510 ("netfilter: ipset: Copy the right MAC address in bitmap:ip,mac and hash:ip,mac sets"), another copy and paste went wrong in commit 8cc4ccf5 ("netfilter: ipset: Allow matching on destination MAC address for mac and ipmac sets"). When I fixed this for IPv4 in 1b4a7510, I didn't realise that hash:ip,mac sets also support IPv6 as family, and this is covered by a separate function, hash_ipmac6_kadt(). In hash:ip,mac sets, the first dimension is the IP address, and the second dimension is the MAC address: check the IPSET_DIM_TWO_SRC flag in flags while deciding which MAC address to copy, destination or source. This way, mixing source and destination matches for the two dimensions of ip,mac hash type works as expected, also for IPv6. With this setup: ip netns add A ip link add veth1 type veth peer name veth2 netns A ip addr add 2001:db8::1/64 dev veth1 ip -net A addr add 2001:db8::2/64 dev veth2 ip link set veth1 up ip -net A link set veth2 up dst=$(ip netns exec A cat /sys/class/net/veth2/address) ip netns exec A ipset create test_hash hash:ip,mac family inet6 ip netns exec A ipset add test_hash 2001:db8::1,${dst} ip netns exec A ip6tables -A INPUT -p icmpv6 --icmpv6-type 135 -j ACCEPT ip netns exec A ip6tables -A INPUT -m set ! --match-set test_hash src,dst -j DROP ipset now correctly matches a test packet: # ping -c1 2001:db8::2 >/dev/null # echo $? 0 Reported-by:
Chen, Yi <yiche@redhat.com> Fixes: 8cc4ccf5 ("netfilter: ipset: Allow matching on destination MAC address for mac and ipmac sets") Signed-off-by:
Stefano Brivio <sbrivio@redhat.com> Signed-off-by:
Jozsef Kadlecsik <kadlec@netfilter.org> Signed-off-by:
-
Suwan Kim authored
[ Upstream commit d4d82577 ] iso_buffer should be set to NULL after use and free in the while loop. In the case of isochronous URB in the while loop, iso_buffer is allocated and after sending it to server, buffer is deallocated. And then, if the next URB in the while loop is not a isochronous pipe, iso_buffer still holds the previously deallocated buffer address and kfree tries to free wrong buffer address. Fixes: ea44d190 ("usbip: Implement SG support to vhci-hcd and stub driver") Reported-by:
kbuild test robot <lkp@intel.com> Reported-by:
Julia Lawall <julia.lawall@lip6.fr> Signed-off-by:
Suwan Kim <suwan.kim027@gmail.com> Reviewed-by:
Shuah Khan <skhan@linuxfoundation.org> Link: https://lore.kernel.org/r/20191022093017.8027-1-suwan.kim027@gmail.comSigned-off-by:
-
Tejun Heo authored
commit 65de03e2 upstream. cgroup writeback tries to refresh the associated wb immediately if the current wb is dead. This is to avoid keeping issuing IOs on the stale wb after memcg - blkcg association has changed (ie. when blkcg got disabled / enabled higher up in the hierarchy). Unfortunately, the logic gets triggered spuriously on inodes which are associated with dead cgroups. When the logic is triggered on dead cgroups, the attempt fails only after doing quite a bit of work allocating and initializing a new wb. While c3aab9a0 ("mm/filemap.c: don't initiate writeback if mapping has no dirty pages") alleviated the issue significantly as it now only triggers when the inode has dirty pages. However, the condition can still be triggered before the inode is switched to a different cgroup and the logic simply doesn't make sense. Skip the immediate switching if the associated memcg is dying. This is a simplified version of the following two patches: * https://lore.kernel.org/linux-mm/20190513183053.GA73423@dennisz-mbp/ * http://lkml.kernel.org/r/156355839560.2063.5265687291430814589.stgit@buzz Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Fixes: e8a7abf5 ("writeback: disassociate inodes from dying bdi_writebacks") Acked-by:
Dennis Zhou <dennis@kernel.org> Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
Jens Axboe <axboe@kernel.dk> Signed-off-by:
-
Konstantin Khlebnikov authored
commit c3aab9a0 upstream. Functions like filemap_write_and_wait_range() should do nothing if inode has no dirty pages or pages currently under writeback. But they anyway construct struct writeback_control and this does some atomic operations if CONFIG_CGROUP_WRITEBACK=y - on fast path it locks inode->i_lock and updates state of writeback ownership, on slow path might be more work. Current this path is safely avoided only when inode mapping has no pages. For example generic_file_read_iter() calls filemap_write_and_wait_range() at each O_DIRECT read - pretty hot path. This patch skips starting new writeback if mapping has no dirty tags set. If writeback is already in progress filemap_write_and_wait_range() will wait for it. Link: http://lkml.kernel.org/r/156378816804.1087.8607636317907921438.stgit@buzzSigned-off-by:
Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Reviewed-by:
Jan Kara <jack@suse.cz> Cc: Tejun Heo <tj@kernel.org> Cc: Jens Axboe <axboe@kernel.dk> Cc: Johannes Weiner <hannes@cmpxchg.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Jean-Baptiste Maneyrol authored
[ Upstream commit 6e82ae6b ] Some chips have a fifo overflow bit issue where the bit is always set. The result is that every data is dropped. Change fifo overflow management by checking fifo count against a maximum value. Add fifo size in chip hardware set of values. Fixes: f5057e7b ("iio: imu: inv_mpu6050: better fifo overflow handling") Cc: stable@vger.kernel.org Signed-off-by:
Jean-Baptiste Maneyrol <jmaneyrol@invensense.com> Signed-off-by:
-
Randolph Maaßen authored
[ Upstream commit 22904bdf ] The Invensense ICM-20602 is a 6-axis MotionTracking device that combines a 3-axis gyroscope and an 3-axis accelerometer. It is very similar to the ICM-20608 imu which is already supported by the mpu6050 driver. The main difference is that the ICM-20602 has the i2c bus disable bit in a separate register. Signed-off-by:
Randolph Maaßen <gaireg@gaireg.de> Signed-off-by:
-
Tejun Heo authored
[ Upstream commit b0814361 ] blkcg_print_stat() iterates blkgs under RCU and doesn't test whether the blkg is online. This can call into pd_stat_fn() on a pd which is still being initialized leading to an oops. The heaviest operation - recursively summing up rwstat counters - is already done while holding the queue_lock. Expand queue_lock to cover the other operations and skip the blkg if it isn't online yet. The online state is protected by both blkcg and queue locks, so this guarantees that only online blkgs are processed. Signed-off-by:
Roman Gushchin <guro@fb.com> Cc: Josef Bacik <jbacik@fb.com> Fixes: 903d23f0 ("blk-cgroup: allow controllers to output their own stats") Cc: stable@vger.kernel.org # v4.19+ Signed-off-by:
-
Hans de Goede authored
[ Upstream commit 63bdef6c ] Commit 03c4749d ("gpio / ACPI: Drop unnecessary ACPI GPIO to Linux GPIO translation") has made the cherryview gpio numbers sparse, to get a 1:1 mapping between ACPI pin numbers and gpio numbers in Linux. This has greatly simplified things, but the code setting the irq_valid_mask was not updated for this, so the valid mask is still in the old "compressed" numbering with the gaps in the pin numbers skipped, which is wrong as irq_valid_mask needs to be expressed in gpio numbers. This results in the following error on devices using pin 24 (0x0018) on the north GPIO controller as an ACPI event source: [ 0.422452] cherryview-pinctrl INT33FF:01: Failed to translate GPIO to IRQ This has been reported (by email) to be happening on a Caterpillar CAT T20 tablet and I've reproduced this myself on a Medion Akoya e2215t 2-in-1. This commit uses the pin number instead of the compressed index into community->pins to clear the correct bits in irq_valid_mask for GPIOs using GPEs for interrupts, fixing these errors and in case of the Medion Akoya e2215t also fixing the LID switch not working. Cc: stable@vger.kernel.org Fixes: 03c4749d ("gpio / ACPI: Drop unnecessary ACPI GPIO to Linux GPIO translation") Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Reviewed-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by:
-
Shuning Zhang authored
[ Upstream commit e74540b2 ] When the extent tree is modified, it should be protected by inode cluster lock and ip_alloc_sem. The extent tree is accessed and modified in the ocfs2_prepare_inode_for_write, but isn't protected by ip_alloc_sem. The following is a case. The function ocfs2_fiemap is accessing the extent tree, which is modified at the same time. kernel BUG at fs/ocfs2/extent_map.c:475! invalid opcode: 0000 [#1] SMP Modules linked in: tun ocfs2 ocfs2_nodemanager configfs ocfs2_stackglue [...] CPU: 16 PID: 14047 Comm: o2info Not tainted 4.1.12-124.23.1.el6uek.x86_64 #2 Hardware name: Oracle Corporation ORACLE SERVER X7-2L/ASM, MB MECH, X7-2L, BIOS 42040600 10/19/2018 task: ffff88019487e200 ti: ffff88003daa4000 task.ti: ffff88003daa4000 RIP: ocfs2_get_clusters_nocache.isra.11+0x390/0x550 [ocfs2] Call Trace: ocfs2_fiemap+0x1e3/0x430 [ocfs2] do_vfs_ioctl+0x155/0x510 SyS_ioctl+0x81/0xa0 system_call_fastpath+0x18/0xd8 Code: 18 48 c7 c6 60 7f 65 a0 31 c0 bb e2 ff ff ff 48 8b 4a 40 48 8b 7a 28 48 c7 c2 78 2d 66 a0 e8 38 4f 05 00 e9 28 fe ff ff 0f 1f 00 <0f> 0b 66 0f 1f 44 00 00 bb 86 ff ff ff e9 13 fe ff ff 66 0f 1f RIP ocfs2_get_clusters_nocache.isra.11+0x390/0x550 [ocfs2] ---[ end trace c8aa0c8180e869dc ]--- Kernel panic - not syncing: Fatal exception Kernel Offset: disabled This issue can be reproduced every week in a production environment. This issue is related to the usage mode. If others use ocfs2 in this mode, the kernel will panic frequently. [akpm@linux-foundation.org: coding style fixes] [Fix new warning due to unused function by removing said function - Linus ] Link: http://lkml.kernel.org/r/1568772175-2906-2-git-send-email-sunny.s.zhang@oracle.comSigned-off-by:
Shuning Zhang <sunny.s.zhang@oracle.com> Reviewed-by:
Junxiao Bi <junxiao.bi@oracle.com> Reviewed-by:
Gang He <ghe@suse.com> Cc: Mark Fasheh <mark@fasheh.com> Cc: Joel Becker <jlbec@evilplan.org> Cc: Joseph Qi <jiangqi903@gmail.com> Cc: Changwei Ge <gechangwei@live.cn> Cc: Jun Piao <piaojun@huawei.com> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Andy Shevchenko authored
[ Upstream commit 29c2c6aa ] When consumer requests a pin, in order to be on the safest side, we switch it first to GPIO mode followed by immediate transition to the input state. Due to posted writes it's luckily to be a single I/O transaction. However, if firmware or boot loader already configures the pin to the GPIO mode, user expects no glitches for the requested pin. We may check if the pin is pre-configured and leave it as is till the actual consumer toggles its state to avoid glitches. Fixes: 7981c001 ("pinctrl: intel: Add Intel Sunrisepoint pin controller and GPIO support") Depends-on: f5a26acf ("pinctrl: intel: Initialize GPIO properly when used through irqchip") Cc: stable@vger.kernel.org Cc: fei.yang@intel.com Reported-by:
Oliver Barta <oliver.barta@aptiv.com> Reported-by:
Malin Jonsson <malin.jonsson@ericsson.com> Signed-off-by:
-
Wenwen Wang authored
[ Upstream commit 8472ba62 ] In e1000_set_ringparam(), 'tx_old' and 'rx_old' are not deallocated if e1000_up() fails, leading to memory leaks. Refactor the code to fix this issue. Signed-off-by:
Wenwen Wang <wenwen@cs.uga.edu> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by:
-
Manfred Rudigier authored
[ Upstream commit 8d5cfd7f ] At least on the i350 there is an annoying behavior that is maybe also present on 82580 devices, but was probably not noticed yet as MAS is not widely used. If no cable is connected on both fiber/copper ports the media auto sense code will constantly swap between them as part of the watchdog task and produce many unnecessary kernel log messages. The swap code responsible for this behavior (switching to fiber) should not be executed if the current media type is copper and there is no signal detected on the fiber port. In this case we can safely wait until the AUTOSENSE_EN bit is cleared. Signed-off-by:
Manfred Rudigier <manfred.rudigier@omicronenergy.com> Tested-by:
-
Chuhong Yuan authored
[ Upstream commit 4202e219 ] The remove misses to disable and unprepare priv->macclk like what is done when probe fails. Add the missed call in remove. Signed-off-by:
Chuhong Yuan <hslester96@gmail.com> Signed-off-by:
-
Trond Myklebust authored
[ Upstream commit be3df3dd ] If the delegation is marked as being revoked, we must not use it for cached opens. Fixes: 869f9dfa ("NFSv4: Fix races between nfs_remove_bad_delegation() and delegation return") Signed-off-by:
Trond Myklebust <trond.myklebust@hammerspace.com> Signed-off-by:
Anna Schumaker <Anna.Schumaker@Netapp.com> Signed-off-by:
-
Felipe Balbi authored
[ Upstream commit d8eca64e ] When disabling an endpoint which has cancelled requests, we should make sure to giveback requests that are currently pending in the cancelled list, otherwise we may fall into a situation where command completion interrupt fires after endpoint has been disabled, therefore causing a splat. Fixes: fec9095b "usb: dwc3: gadget: remove wait_end_transfer" Reported-by:
Roger Quadros <rogerq@ti.com> Signed-off-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Link: https://lore.kernel.org/r/20191031090713.1452818-1-felipe.balbi@linux.intel.comSigned-off-by:
-
Haiyang Zhang authored
[ Upstream commit 719b85c3 ] If rndis_filter_open() fails, we need to remove the rndis device created in earlier steps, before returning an error code. Otherwise, the retry of netvsc_attach() from its callers will fail and hang. Fixes: 7b2ee50c ("hv_netvsc: common detach logic") Signed-off-by:
Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by:
-
Michael Strauss authored
[ Upstream commit bc2fde42 ] [WHY] i2c_read is called to differentiate passive DP->HDMI and DP->DVI-D dongles The call is expected to fail in DVI-D case but pass in HDMI case Some HDMI dongles have a chance to fail as well, causing misdetection as DVI-D [HOW] Retry i2c_read to ensure failed result is valid Signed-off-by:
Michael Strauss <michael.strauss@amd.com> Reviewed-by:
Tony Cheng <Tony.Cheng@amd.com> Acked-by:
Leo Li <sunpeng.li@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Andrey Grodzovsky authored
[ Upstream commit 57c0f58e ] Use ERR_PTR to return back the error happened during amdgpu_ib_schedule. Signed-off-by:
Andrey Grodzovsky <andrey.grodzovsky@amd.com> Reviewed-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
-
Takashi Iwai authored
[ Upstream commit ad3e8da2 ] Acer Aspire A315-41 requires the very same workaround as the existing quirk for Dell Latitude 5495. Add the new entry for that. BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1137799Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
Joerg Roedel <jroedel@suse.de> Signed-off-by:
-
Vladimir Oltean authored
[ Upstream commit b9cd75e6 ] The switch driver keeps a "vid" variable per port, which signifies _the_ VLAN ID that is stripped on that port's egress (aka the native VLAN on a trunk port). That is the way the hardware is designed (mostly). The port->vid is programmed into REW:PORT:PORT_VLAN_CFG:PORT_VID and the rewriter is told to send all traffic as tagged except the one having port->vid. There exists a possibility of finer-grained egress untagging decisions: using the VCAP IS1 engine, one rule can be added to match every VLAN-tagged frame whose VLAN should be untagged, and set POP_CNT=1 as action. However, the IS1 can hold at most 512 entries, and the VLANs are in the order of 6 * 4096. So the code is fine for now. But this sequence of commands: $ bridge vlan add dev swp0 vid 1 pvid untagged $ bridge vlan add dev swp0 vid 2 untagged makes untagged and pvid-tagged traffic be sent out of swp0 as tagged with VID 1, despite user's request. Prevent that from happening. The user should temporarily remove the existing untagged VLAN (1 in this case), add it back as tagged, and then add the new untagged VLAN (2 in this case). Cc: Antoine Tenart <antoine.tenart@bootlin.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Fixes: 7142529f ("net: mscc: ocelot: add VLAN filtering") Signed-off-by:
Vladimir Oltean <olteanv@gmail.com> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Acked-by:
Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by:
-
Vladimir Oltean authored
[ Upstream commit 1c44ce56 ] Background information: the driver operates the hardware in a mode where a single VLAN can be transmitted as untagged on a particular egress port. That is the "native VLAN on trunk port" use case. Its value is held in port->vid. Consider the following command sequence (no network manager, all interfaces are down, debugging prints added by me): $ ip link add dev br0 type bridge vlan_filtering 1 $ ip link set dev swp0 master br0 Kernel code path during last command: br_add_slave -> ocelot_netdevice_port_event (NETDEV_CHANGEUPPER): [ 21.401901] ocelot_vlan_port_apply: port 0 vlan aware 0 pvid 0 vid 0 br_add_slave -> nbp_vlan_init -> switchdev_port_attr_set -> ocelot_port_attr_set (SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING): [ 21.413335] ocelot_vlan_port_apply: port 0 vlan aware 1 pvid 0 vid 0 br_add_slave -> nbp_vlan_init -> nbp_vlan_add -> br_switchdev_port_vlan_add -> switchdev_port_obj_add -> ocelot_port_obj_add -> ocelot_vlan_vid_add [ 21.667421] ocelot_vlan_port_apply: port 0 vlan aware 1 pvid 1 vid 1 So far so good. The bridge has replaced the driver's default pvid used in standalone mode (0) with its own default_pvid (1). The port's vid (native VLAN) has also changed from 0 to 1. $ ip link set dev swp0 up [ 31.722956] 8021q: adding VLAN 0 to HW filter on device swp0 do_setlink -> dev_change_flags -> vlan_vid_add -> ocelot_vlan_rx_add_vid -> ocelot_vlan_vid_add: [ 31.728700] ocelot_vlan_port_apply: port 0 vlan aware 1 pvid 1 vid 0 The 8021q module uses the .ndo_vlan_rx_add_vid API on .ndo_open to make ports be able to transmit and receive 802.1p-tagged traffic by default. This API is supposed to offload a VLAN sub-interface, which for a switch port means to add a VLAN that is not a pvid, and tagged on egress. But the driver implementation of .ndo_vlan_rx_add_vid is wrong: it adds back vid 0 as "egress untagged". Now back to the initial paragraph: there is a single untagged VID that the driver keeps track of, and that has just changed from 1 (the pvid) to 0. So this breaks the bridge core's expectation, because it has changed vid 1 from untagged to tagged, when what the user sees is. $ bridge vlan port vlan ids swp0 1 PVID Egress Untagged br0 1 PVID Egress Untagged But curiously, instead of manifesting itself as "untagged and pvid-tagged traffic gets sent as tagged on egress", the bug: - is hidden when vlan_filtering=0 - manifests as dropped traffic when vlan_filtering=1, due to this setting: if (port->vlan_aware && !port->vid) /* If port is vlan-aware and tagged, drop untagged and priority * tagged frames. */ val |= ANA_PORT_DROP_CFG_DROP_UNTAGGED_ENA | ANA_PORT_DROP_CFG_DROP_PRIO_S_TAGGED_ENA | ANA_PORT_DROP_CFG_DROP_PRIO_C_TAGGED_ENA; which would have made sense if it weren't for this bug. The setting's intention was "this is a trunk port with no native VLAN, so don't accept untagged traffic". So the driver was never expecting to set VLAN 0 as the value of the native VLAN, 0 was just encoding for "invalid". So the fix is to not send 802.1p traffic as untagged, because that would change the port's native vlan to 0, unbeknownst to the bridge, and trigger unexpected code paths in the driver. Cc: Antoine Tenart <antoine.tenart@bootlin.com> Cc: Alexandre Belloni <alexandre.belloni@bootlin.com> Fixes: 7142529f ("net: mscc: ocelot: add VLAN filtering") Signed-off-by:
Horatiu Vultur <horatiu.vultur@microchip.com> Signed-off-by:
-
Jiangfeng Xiao authored
[ Upstream commit 63a41746 ] When rmmod hip04_eth.ko, we can get the following warning: Task track: rmmod(1623)>bash(1591)>login(1581)>init(1) ------------[ cut here ]------------ WARNING: CPU: 0 PID: 1623 at kernel/irq/manage.c:1557 __free_irq+0xa4/0x2ac() Trying to free already-free IRQ 200 Modules linked in: ping(O) pramdisk(O) cpuinfo(O) rtos_snapshot(O) interrupt_ctrl(O) mtdblock mtd_blkdevrtfs nfs_acl nfs lockd grace sunrpc xt_tcpudp ipt_REJECT iptable_filter ip_tables x_tables nf_reject_ipv CPU: 0 PID: 1623 Comm: rmmod Tainted: G O 4.4.193 #1 Hardware name: Hisilicon A15 [<c020b408>] (rtos_unwind_backtrace) from [<c0206624>] (show_stack+0x10/0x14) [<c0206624>] (show_stack) from [<c03f2be4>] (dump_stack+0xa0/0xd8) [<c03f2be4>] (dump_stack) from [<c021a780>] (warn_slowpath_common+0x84/0xb0) [<c021a780>] (warn_slowpath_common) from [<c021a7e8>] (warn_slowpath_fmt+0x3c/0x68) [<c021a7e8>] (warn_slowpath_fmt) from [<c026876c>] (__free_irq+0xa4/0x2ac) [<c026876c>] (__free_irq) from [<c0268a14>] (free_irq+0x60/0x7c) [<c0268a14>] (free_irq) from [<c0469e80>] (release_nodes+0x1c4/0x1ec) [<c0469e80>] (release_nodes) from [<c0466924>] (__device_release_driver+0xa8/0x104) [<c0466924>] (__device_release_driver) from [<c0466a80>] (driver_detach+0xd0/0xf8) [<c0466a80>] (driver_detach) from [<c0465e18>] (bus_remove_driver+0x64/0x8c) [<c0465e18>] (bus_remove_driver) from [<c02935b0>] (SyS_delete_module+0x198/0x1e0) [<c02935b0>] (SyS_delete_module) from [<c0202ed0>] (__sys_trace_return+0x0/0x10) ---[ end trace bb25d6123d849b44 ]--- Currently "rmmod hip04_eth.ko" call free_irq more than once as devres_release_all and hip04_remove both call free_irq. This results in a 'Trying to free already-free IRQ' warning. To solve the problem free_irq has been moved out of hip04_remove. Signed-off-by:
Jiangfeng Xiao <xiaojiangfeng@huawei.com> Signed-off-by:
-
Will Deacon authored
[ Upstream commit 85ac30fa ] In the highly unlikely event that we fail to allocate either of the "/txrx" or "/control" workqueues, we should bail cleanly rather than blindly march on with NULL queue pointer(s) installed in the 'fjes_adapter' instance. Cc: "David S. Miller" <davem@davemloft.net> Reported-by:
Nicolas Waisman <nico@semmle.com> Link: https://lore.kernel.org/lkml/CADJ_3a8WFrs5NouXNqS5WYe7rebFP+_A5CheeqAyD_p7DFJJcg@mail.gmail.com/Signed-off-by:
Will Deacon <will@kernel.org> Signed-off-by:
-
Anton Eidelman authored
[ Upstream commit af8fd042 ] The following scenario results in an IO hang: 1) ctrl completes a request with NVME_SC_ANA_TRANSITION. NVME_NS_ANA_PENDING bit in ns->flags is set and ana_work is triggered. 2) ana_work: nvme_read_ana_log() tries to get the ANA log page from the ctrl. This fails because ctrl disconnects. Therefore nvme_update_ns_ana_state() is not called and NVME_NS_ANA_PENDING bit in ns->flags is not cleared. 3) ctrl reconnects: nvme_mpath_init(ctrl,...) calls nvme_read_ana_log(ctrl, groups_only=true). However, nvme_update_ana_state() does not update namespaces because nr_nsids = 0 (due to groups_only mode). 4) scan_work calls nvme_validate_ns() finds the ns and re-validates OK. Result: The ctrl is now live but NVME_NS_ANA_PENDING bit in ns->flags is still set. Consequently ctrl will never be considered a viable path by __nvme_find_path(). IO will hang if ctrl is the only or the last path to the namespace. More generally, while ctrl is reconnecting, its ANA state may change. And because nvme_mpath_init() requests ANA log in groups_only mode, these changes are not propagated to the existing ctrl namespaces. This may result in a mal-function or an IO hang. Solution: nvme_mpath_init() will nvme_read_ana_log() with groups_only set to false. This will not harm the new ctrl case (no namespaces present), and will make sure the ANA state of namespaces gets updated after reconnect. Note: Another option would be for nvme_mpath_init() to invoke nvme_parse_ana_log(..., nvme_set_ns_ana_state) for each existing namespace. Reviewed-by:
Sagi Grimberg <sagi@grimberg.me> Signed-off-by:
Anton Eidelman <anton@lightbitslabs.com> Signed-off-by:
Keith Busch <kbusch@kernel.org> Signed-off-by:
-
Nicholas Piggin authored
[ Upstream commit d3566abb ] In shutdown/reboot paths, the timer is not stopped: qla2x00_shutdown pci_device_shutdown device_shutdown kernel_restart_prepare kernel_restart sys_reboot This causes lockups (on powerpc) when firmware config space access calls are interrupted by smp_send_stop later in reboot. Fixes: e30d1756 ("[SCSI] qla2xxx: Addition of shutdown callback handler.") Link: https://lore.kernel.org/r/20191024063804.14538-1-npiggin@gmail.comSigned-off-by:
Nicholas Piggin <npiggin@gmail.com> Acked-by:
Himanshu Madhani <hmadhani@marvell.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Lijun Ou authored
[ Upstream commit b681a052 ] eq->buf_list->buf and eq->buf_list should also be freed when eqe_hop_num is set to 0, or there will be memory leaks. Fixes: a5073d60 ("RDMA/hns: Add eq support of hip08") Link: https://lore.kernel.org/r/1572072995-11277-3-git-send-email-liweihang@hisilicon.comSigned-off-by:
Lijun Ou <oulijun@huawei.com> Signed-off-by:
Weihang Li <liweihang@hisilicon.com> Signed-off-by:
Jason Gunthorpe <jgg@mellanox.com> Signed-off-by:
-
Potnuri Bharat Teja authored
[ Upstream commit d4934f45 ] _put_ep_safe() and _put_pass_ep_safe() free the skb before it is freed by process_work(). fix double free by freeing the skb only in process_work(). Fixes: 1dad0ebe ("iw_cxgb4: Avoid touch after free error in ARP failure handlers") Link: https://lore.kernel.org/r/1572006880-5800-1-git-send-email-bharat@chelsio.comSigned-off-by:
Dakshaja Uppalapati <dakshaja@chelsio.com> Signed-off-by:
Potnuri Bharat Teja <bharat@chelsio.com> Reviewed-by:
-
GwanYeong Kim authored
[ Upstream commit 28df0642 ] This isn't really accurate right. fread() doesn't always return 0 in error. It could return < number of elements and set errno. Signed-off-by:
GwanYeong Kim <gy741.kim@gmail.com> Acked-by:
-
Johan Hovold authored
[ Upstream commit 88f6bf38 ] A recent info-leak bug manifested itself along with warning about a negative buffer overflow: ldusb 1-1:0.28: Read buffer overflow, -131383859965943 bytes dropped when it was really a rather large positive one. A sanity check that prevents this has now been put in place, but let's fix up the size format specifiers, which should all be unsigned. Signed-off-by:
Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20191022143203.5260-3-johan@kernel.orgSigned-off-by:
-
Alan Stern authored
[ Upstream commit d482c7bb ] Endpoints with a maxpacket length of 0 are probably useless. They can't transfer any data, and it's not at all unlikely that an HCD will crash or hang when trying to handle an URB for such an endpoint. Currently the USB core does not check for endpoints having a maxpacket value of 0. This patch adds a check, printing a warning and skipping over any endpoints it catches. Now, the USB spec does not rule out endpoints having maxpacket = 0. But since they wouldn't have any practical use, there doesn't seem to be any good reason for us to accept them. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1910281050420.1485-100000@iolanthe.rowland.orgSigned-off-by:
-
Kan Liang authored
[ Upstream commit 75be6f70 ] The events in the same group don't start or stop simultaneously. Here is the ftrace when enabling event group for uncore_iio_0: # perf stat -e "{uncore_iio_0/event=0x1/,uncore_iio_0/event=0xe/}" <idle>-0 [000] d.h. 8959.064832: read_msr: a41, value b2b0b030 //Read counter reg of IIO unit0 counter0 <idle>-0 [000] d.h. 8959.064835: write_msr: a48, value 400001 //Write Ctrl reg of IIO unit0 counter0 to enable counter0. <------ Although counter0 is enabled, Unit Ctrl is still freezed. Nothing will count. We are still good here. <idle>-0 [000] d.h. 8959.064836: read_msr: a40, value 30100 //Read Unit Ctrl reg of IIO unit0 <idle>-0 [000] d.h. 8959.064838: write_msr: a40, value 30000 //Write Unit Ctrl reg of IIO unit0 to enable all counters in the unit by clear Freeze bit <------Unit0 is un-freezed. Counter0 has been enabled. Now it starts counting. But counter1 has not been enabled yet. The issue starts here. <idle>-0 [000] d.h. 8959.064846: read_msr: a42, value 0 //Read counter reg of IIO unit0 counter1 <idle>-0 [000] d.h. 8959.064847: write_msr: a49, value 40000e //Write Ctrl reg of IIO unit0 counter1 to enable counter1. <------ Now, counter1 just starts to count. Counter0 has been running for a while. Current code un-freezes the Unit Ctrl right after the first counter is enabled. The subsequent group events always loses some counter values. Implement pmu_enable and pmu_disable support for uncore, which can help to batch hardware accesses. No one uses uncore_enable_box and uncore_disable_box. Remove them. Signed-off-by:
Kan Liang <kan.liang@linux.intel.com> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Namhyung Kim <namhyung@kernel.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Vince Weaver <vincent.weaver@maine.edu> Cc: linux-drivers-review@eclists.intel.com Cc: linux-perf@eclists.intel.com Fixes: 087bfbb0 ("perf/x86: Add generic Intel uncore PMU support") Link: https://lkml.kernel.org/r/1572014593-31591-1-git-send-email-kan.liang@linux.intel.comSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Kim Phillips authored
[ Upstream commit e431e79b ] This saves us writing the IBS control MSR twice when disabling the event. I searched revision guides for all families since 10h, and did not find occurrence of erratum #420, nor anything remotely similar: so we isolate the secondary MSR write to family 10h only. Also unconditionally update the count mask for IBS Op implementations that have read & writeable current count (CurCnt) fields in addition to the MaxCnt field. These bits were reserved on prior implementations, and therefore shouldn't have negative impact. Signed-off-by:
Kim Phillips <kim.phillips@amd.com> Signed-off-by:
-
