- 02 Aug, 2010 21 commits
-
-
Santosh Shilimkar authored
This patch adds cpu hotplug support for OMAP4430. Only CPU inactive state is supported as a low power state in the basic hot-plug support Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Cc: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Santosh Shilimkar authored
This patch adds a secure API to read AuxCoreBoot0 register to check the cpu boot status. It also moves the other smc APIs to common omap44xx-smc.S. This APIs should not be marked as __INIT because we need these to be present for CPU hotplug Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Rajendra Nayak authored
This patch adds support for basic suspend doing a CPUx wfi for OMAP4. All powerdomains are for now are kept programmed in ON state. Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Cc: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Deepak K authored
Errata i202 (OMAP3430 - 1.12, OMAP3630 - 1.6): UART module MDR1 register access can cause a dummy underrun condition which could result in a freeze in the case of IrDA communication or if used as UART, corrupted data. Workaround is as follows for everytime MDR1 register is changed: * setup all required UART registers * setup MDR1.MODE_SELECT bit field * Wait 5 L4 clk cycles + 5 UART functional clock cycles * Clear the Tx and RX fifo using FCR register Note: The following step is not done as I am assuming it is not needed due to reconfiguration being done and there is no halted operation perse. * Read if required, the RESUME register to resume halted operation Based on an earlier patch at: http://git.omapzoom.org/?p=kernel/omap.git;a=commitdiff;h=42d4a342c009bd9727c100abc8a4bc3063c22f0cSigned-off-by: Deepak K <deepak.k@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Nishanth Menon authored
introduce silicon specific quirks as a errata handling mechanism as a start UART_ERRATA_FIFO_FULL_ABORT is used to handle the override for fifo full condition for rx and tx. Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Nishanth Menon authored
Remove the following sparse warnings by declaring attr as static: arch/arm/mach-omap2/serial.c:627:1: warning: symbol 'dev_attr_sleep_timeout' was not declared. Should it be static? Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Nishanth Menon authored
Initialization of pointer should be done with NULL. Removes sparse warnings: arch/arm/mach-omap2/serial.c:566:17: warning: Using plain integer as NULL pointer arch/arm/mach-omap2/serial.c:567:17: warning: Using plain integer as NULL pointer Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Govindraj R authored
Adds context save/restore for mcr register as state of mcr register is lost after core off. Signed-off-by: Govindraj R <govindraj.raja@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
David Anders authored
Add initial support for the OMAP4 based Panda Board. Signed-off-by: David Anders <x0132446@ti.com> [tony@atomide.com: selected board by default in Kconfig] Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Hemanth V authored
This patch adds support for GPIO LEDs present on OMAP4 SDP and Blaze boards. This basically adds platform data required by leds-gpio driver Signed-off-by: Hemanth V <hemanthv@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Shubhrajyoti Datta authored
Adding board configuration for the tmp105 temperature sensor. The interface to the sensor is I2C. Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Santosh Shilimkar authored
The MMC1 and MMC2 cards have seperate LDO supplies. Current code assumes that they are powered by same LDO. This patch fixes the same and has VAUX1 as supply to MMC2 card. Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com> Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com> Tested-by: Kishore Kadiyala <kishore.kadiyala@ti.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Mathias Nyman authored
This commit will enable usage of tsl2563 ambient light sensor on Nokia N900. Signed-off-by: Ameya Palande <ameya.palande@nokia.com> Signed-off-by: Mathias Nyman <mathias.nyman@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Jarkko Nikula authored
With these and upcoming change to tpa6130a2 driver it's possible to add support for the TPA6130A2 headphone amplifier. Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Jarkko Nikula authored
There is REGULATOR_SUPPLY macro available for initializing the struct regulator_consumer_supply so use it where applicable (all other supplies than vdds_sdi) as it improves the readability. Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Acked-by: Eduardo Valentin <eduardo.valentin@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Jarkko Nikula authored
Proper operation of the tlv320aic3x audio codec requires that reset sequencing is done in pair with supply voltages when using the regulator framework. Add the codec reset gpio used in Nokia RX51 to tlv320aic3x data. Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Jarkko Nikula authored
It seems that the battery cover sensor in Nokia N900 is powered from the V28 domain. Now if this regulator is disabled it causes that the gpio 160 reads only zero which effectively causes uSD removal detection. Currently the bootloader enabled V28 is kept on but this may change in the future according to comment in drivers/regulator/core.c: regulator_has_full_constraints. Also if there are any consumers on the V28 domain doing regulator_enable regulator_disable cycle the V28 will be disabled after that. Prepare for these by defining the V28 as always_on regulator. Signed-off-by: Jarkko Nikula <jhnikula@gmail.com> Cc: Adrian Hunter <adrian.hunter@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Grazvydas Ignotas authored
Add platform data for NAND and wifi, also setup all GPIOs needed to use the wifi chip. Signed-off-by: Grazvydas Ignotas <notasas@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Grazvydas Ignotas authored
Update gpio-keys setup so it matches what is on default firmware. Also make use of debounce feature in gpio-keys instead of setting it explicitly, as gpio-keys is now capable of using hardware debounce on OMAPs thanks to recent gpiolib changes. Also fix a sparce warning along the way. Signed-off-by: Grazvydas Ignotas <notasas@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Ohad Ben-Cohen authored
Add board muxing to support the wlan wl1271 chip that is hardwired to mmc2 (third mmc controller) on the ZOOM3. Signed-off-by: Ohad Ben-Cohen <ohadb@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Ohad Ben-Cohen authored
Add board muxing to support the wlan wl1271 chip that is hardwired to mmc2 (third mmc controller) on the ZOOM2. Signed-off-by: Ohad Ben-Cohen <ohadb@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
- 05 Jul, 2010 19 commits
-
-
Thomas Weber authored
Devkit8000 uses the TPS65930 and not the TWL4030. The TPS65930 uses only a subset of the power supplies of the TWL4030. Signed-off-by: Thomas Weber <weber@corscience.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Thomas Weber authored
omap_board_config is no longer used and thats why empty. This patch removes the empty omap_board_config. Signed-off-by: Thomas Weber <weber@corscience.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Thomas Weber authored
Using the macro gpio_is_valid for check of valid gpio pins. Signed-off-by: Thomas Weber <weber@corscience.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Thomas Weber authored
Replacing supplies with the REGULATOR_SUPPLY macro. Signed-off-by: Thomas Weber <weber@corscience.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Thomas Weber authored
devkit8000_panel_enable_tv and devkit8000_panel_disable_tv are already done in DSS2 code. So they are no longer needed in board code. Signed-off-by: Thomas Weber <weber@corscience.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Thomas Weber authored
The Devkit8000 uses the cost reduced variant tps65930 of the twl4030. The TPS65930 only has vdd1, vdd2, vpll1, vio, vmmc1, vdac and vaux2. vaux2 is not used on Devkit8000. Signed-off-by: Thomas Weber <weber@corscience.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Thomas Weber authored
The VDVI power supply is no longer needed in board code with the new DSS2 interface. Signed-off-by: Thomas Weber <weber@corscience.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Kan-Ru Chen authored
This patch corrects the LCD reset pin configuration. Original code from early devkit8000 patch sets the TWL4030 GPIO_1 to EHCI_nOC and TWL4030_GPIO_MAX+1 to ledA. Indeed these two pins are both LCD_PWREN. Setup the lcd reset_gpio properly so it can be disabled when other display is turned on. Signed-off-by: Kan-Ru Chen <kanru@0xlab.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Kan-Ru Chen authored
This patch corrects the DVI-D output setup of Devkit8000 Devkit8000 has different DVI reset pin with the BeagleBoard. On Devkit8000 the TWL4030 GPIO_7 is assigned to do the job. Signed-off-by: Kan-Ru Chen <kanru@0xlab.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Thomas Weber authored
Choose the generic panel for lcd code of Devkit8000. Signed-off-by: Thomas Weber <weber@corscience.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Thomas Weber authored
Corrected the wrong power supplies in devkit8000 code. Add supply for ads7846 to support the new regulator framework for touchscreen. Signed-off-by: Thomas Weber <weber@corscience.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Christoph Egger authored
MACH_OMAP2_H4_USB1 doesn't exist in Kconfig, therefore removing all references for it from the source code. Signed-off-by: Christoph Egger <siccegge@cs.fau.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Christoph Egger authored
MACH_OMAP_H4_OTG doesn't exist in Kconfig, therefore removing all references for it from the source code. Signed-off-by: Christoph Egger <siccegge@cs.fau.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Christoph Egger authored
APM doesn't exist in Kconfig, therefore removing all references for it from the source code. Signed-off-by: Christoph Egger <siccegge@cs.fau.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Christoph Egger authored
LEDS_OMAP_DEBUG doesn't exist in Kconfig, therefore replacing all references for it with OMAP_DEBUG_LEDS from the source code. Signed-off-by: Christoph Egger <siccegge@cs.fau.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Christoph Egger authored
OMAP_STI doesn't exist in Kconfig, therefore removing all references for it from the source code. Signed-off-by: Christoph Egger <siccegge@cs.fau.de> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Christoph Egger authored
OMAP_DSP doesn't exist in Kconfig, therefore removing all references for it from the source code. Signed-off-by: Christoph Egger <siccegge@cs.fau.de> [tony@atomide.com: updated to apply on top of already queued patches] Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Christoph Egger authored
OMAP_IR doesn't exist in Kconfig, therefore removing all references for it from the source code. Signed-off-by: Christoph Egger <siccegge@cs.fau.de> [tony@atomide.com: updated for new mux code] Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Christoph Egger authored
OMAP_MUX_ERRORS doesn't exist in Kconfig, therefore replacing all references for it with OMAP_MUX_WARNINGS in the source code. Signed-off-by: Christoph Egger <siccegge@cs.fau.de> Acked-by: Kirill A. Shutemov <kirill@shutemov.name> Signed-off-by: Tony Lindgren <tony@atomide.com>
-