The ath79_device_reset_* are causing BUG when
those are used on the QCA955x SoCs. The patch
adds the required code to avoid that.

Cc: Rodriguez, Luis <rodrigue@qca.qualcomm.com>
Cc: Giori, Kathy <kgiori@qca.qualcomm.com>
Cc: QCA Linux Team <qca-linux-team@qca.qualcomm.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4948/Signed-off-by: John Crispin <blogic@openwrt.org>

The existing code can handle the GPIO controller of
the QCA955x SoCs. Add a minimal glue code to make it
working.

Cc: Rodriguez, Luis <rodrigue@qca.qualcomm.com>
Cc: Giori, Kathy <kgiori@qca.qualcomm.com>
Cc: QCA Linux Team <qca-linux-team@qca.qualcomm.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4947/Signed-off-by: John Crispin <blogic@openwrt.org>

The IRQ routing in the QCA955x SoCs is slightly
different from the routing implemented in the
already supported SoCs.

Cc: Rodriguez, Luis <rodrigue@qca.qualcomm.com>
Cc: Giori, Kathy <kgiori@qca.qualcomm.com>
Cc: QCA Linux Team <qca-linux-team@qca.qualcomm.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4955/Signed-off-by: John Crispin <blogic@openwrt.org>

The patch adds code to get various clock frequencies
from the PLLs used in the QCA955x SoCs.

Cc: Rodriguez, Luis <rodrigue@qca.qualcomm.com>
Cc: Giori, Kathy <kgiori@qca.qualcomm.com>
Cc: QCA Linux Team <qca-linux-team@qca.qualcomm.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4945/Signed-off-by: John Crispin <blogic@openwrt.org>

Also add 'soc_is_qca955[68x]' helper functions
and a Kconfig symbol for the SoC family.

Cc: Rodriguez, Luis <rodrigue@qca.qualcomm.com>
Cc: Giori, Kathy <kgiori@qca.qualcomm.com>
Cc: QCA Linux Team <qca-linux-team@qca.qualcomm.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4943/Signed-off-by: John Crispin <blogic@openwrt.org>

The patch allows to see kernel messages on the
QCA955X SoCs in early boot stage.

Cc: Rodriguez, Luis <rodrigue@qca.qualcomm.com>
Cc: Giori, Kathy <kgiori@qca.qualcomm.com>
Cc: QCA Linux Team <qca-linux-team@qca.qualcomm.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4944/Signed-off-by: John Crispin <blogic@openwrt.org>

The '.start' field of the IRQ resource assigned twice
in ar934x_wmac_setup(). The second assignment must
set the '.end' field. Fix it.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4954/Signed-off-by: John Crispin <blogic@openwrt.org>

/proc/vmcore wasn't showing up in kdump kernels.  It turns that that
for Octeon, the memory used by elfcorehdr wasn't being set aside
properly and it was getting clobbered before /proc/vmcore could get
it.  So reserve the memory if it shows up in a memory area managed
by the kernel.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Acked-by: David Daney  <ddaney@caviumnetworks.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/4936/

Kernel memory isn't necessarily added to the memory tables, so it
wouldn't show up in /proc/iomem.  This was breaking kdump, which
requires these memory addresses to work correctly.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Acked-by: David Daney <ddaney@caviumnetworks.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/4937/

The current code uses static resources and static platform
device instances for the possible USB controllers in the
system. These static variables contains initial values which
leads to data segment pollution.

Remove the static variables and use dynamically allocated
structures instead.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4933/Signed-off-by: John Crispin <blogic@openwrt.org>

Use the ATH79_MISC_IRQ() macro instead.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4930/Signed-off-by: John Crispin <blogic@openwrt.org>

Remove the individual ATH79_CPU_IRQ_* constants and
use the new macro instead of those.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4929/Signed-off-by: John Crispin <blogic@openwrt.org>

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4928/Signed-off-by: John Crispin <blogic@openwrt.org>

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4927/Signed-off-by: John Crispin <blogic@openwrt.org>

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4926/Signed-off-by: John Crispin <blogic@openwrt.org>

The command register of the PCI controller is
not initialized correctly by the bootloader on
some boards and this leads to non working PCI
bus.

Add code to initialize the command register
from the Linux code to avoid this.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4916/Signed-off-by: John Crispin <blogic@openwrt.org>

Change to the code to use per-controller IRQ base.
This is needed for multiple PCI controller support.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4915/Signed-off-by: John Crispin <blogic@openwrt.org>

Static resources become impractical when multiple
PCI controllers are present. Move the resources
into the platform device registration code and
change the probe routine to get those from there
platform device's resources.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4914/Signed-off-by: John Crispin <blogic@openwrt.org>

The current code uses static variables to store the
PCI controller specific data. This works if the system
contains one PCI controller only, however it becomes
impractical when multiple PCI controllers are present.

Move the variables into a dynamically allocated controller
specific structure, and use that instead of the static
variables.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4912/Signed-off-by: John Crispin <blogic@openwrt.org>

This is needed for multiple PCI bus support.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4913/Signed-off-by: John Crispin <blogic@openwrt.org>

The pci_load_of_ranges function is only available if
CONFIG_OF is selected. If the function is used without
CONFIG_OF being enabled it will cause a build error.

Add a dummy inline function to avoid this.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4911/Signed-off-by: John Crispin <blogic@openwrt.org>

The IO and memory resources of a PCI controller
might already have a parent resource set when
they are passed to 'register_pci_controller'.

If the parent resource is set, the request_resource
call will fail due to resource conflict and the
current code will not be able to register the
PCI controller.

Use the parent resource if it is available in the
request_resource call to avoid the isssue.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4910/Signed-off-by: John Crispin <blogic@openwrt.org>

The functions are unused now, so remove them.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4909/Signed-off-by: John Crispin <blogic@openwrt.org>

The pci-ar71xx and pci-ar724x drivers were converted
into platform drivers. Register the corresponding
platform devices for the PCI controllers instead
of using the ar7{1x,24}x_pcibios_init functions.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4908/Signed-off-by: John Crispin <blogic@openwrt.org>

The constants will be used by a subsequent patch.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4907/Signed-off-by: John Crispin <blogic@openwrt.org>

The patch converts the pci-ar71xx driver into a
platform driver. This makes it possible to register
the PCI controller as a plain platform device.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4906/Signed-off-by: John Crispin <blogic@openwrt.org>

The patch converts the pci-ar724x driver into a
platform driver. This makes it possible to register
the PCI controller as a plain platform device.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4905/Signed-off-by: John Crispin <blogic@openwrt.org>

Convert the ralink IRQ code to make use of the new MIPS IRQ controller OF
mappings.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: David Daney <david.daney@cavium.com>
Patchwork: http://patchwork.linux-mips.org/patch/4900/

Add code to load a irq_domain for the MIPS IRQ controller from a devicetree
file.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: David Daney <david.daney@cavium.com>
Patchwork: http://patchwork.linux-mips.org/patch/4902/

Signed-off-by: John Crispin <blogic@openwrt.org>
Acked-by: David Daney <david.daney@cavium.com>
Patchwork: http://patchwork.linux-mips.org/patch/4901/

Signed-off-by: John Crispin <blogic@openwrt.org>

Add the Kbuild symbols and Makefiles needed to actually build the ralink code
from this series
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4899/

This adds the devicetree file that describes the rt305x evaluation kit.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4898/

Add support code for rt3050, rt3052, rt3350, rt3352 and rt5350 SOC.

The code detects the SoC and registers the clk / pinmux settings.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4896/

Add the code needed to make early printk work.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4897/

Until there is a generic MIPS way of handing the DTB over from bootloader to
kernel we rely on a built in devicetrees. The OF code also remaps those register
ranges that we use global in our drivers.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4895/

These SoCs have a limited number of fixed rate clocks. Add support for the
clk and clkdev api.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4894/

Add minimal code to handle commandlines.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4892/

Resetting these SoCs requires no real magic. The code is straight forward.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4891/

All of the Ralink Wifi SoC currently supported by this series share the same
interrupt controller (INTC).
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4890/