- 30 Jun, 2020 40 commits
-
-
Guoqing Jiang authored
BugLink: https://bugs.launchpad.net/bugs/1884564 [ Upstream commit f6766ff6 ] We need to check mddev->del_work before flush workqueu since the purpose of flush is to ensure the previous md is disappeared. Otherwise the similar deadlock appeared if LOCKDEP is enabled, it is due to md_open holds the bdev->bd_mutex before flush workqueue. kernel: [ 154.522645] ====================================================== kernel: [ 154.522647] WARNING: possible circular locking dependency detected kernel: [ 154.522650] 5.6.0-rc7-lp151.27-default #25 Tainted: G O kernel: [ 154.522651] ------------------------------------------------------ kernel: [ 154.522653] mdadm/2482 is trying to acquire lock: kernel: [ 154.522655] ffff888078529128 ((wq_completion)md_misc){+.+.}, at: flush_workqueue+0x84/0x4b0 kernel: [ 154.522673] kernel: [ 154.522673] but task is already holding lock: kernel: [ 154.522675] ffff88804efa9338 (&bdev->bd_mutex){+.+.}, at: __blkdev_get+0x79/0x590 kernel: [ 154.522691] kernel: [ 154.522691] which lock already depends on the new lock. kernel: [ 154.522691] kernel: [ 154.522694] kernel: [ 154.522694] the existing dependency chain (in reverse order) is: kernel: [ 154.522696] kernel: [ 154.522696] -> #4 (&bdev->bd_mutex){+.+.}: kernel: [ 154.522704] __mutex_lock+0x87/0x950 kernel: [ 154.522706] __blkdev_get+0x79/0x590 kernel: [ 154.522708] blkdev_get+0x65/0x140 kernel: [ 154.522709] blkdev_get_by_dev+0x2f/0x40 kernel: [ 154.522716] lock_rdev+0x3d/0x90 [md_mod] kernel: [ 154.522719] md_import_device+0xd6/0x1b0 [md_mod] kernel: [ 154.522723] new_dev_store+0x15e/0x210 [md_mod] kernel: [ 154.522728] md_attr_store+0x7a/0xc0 [md_mod] kernel: [ 154.522732] kernfs_fop_write+0x117/0x1b0 kernel: [ 154.522735] vfs_write+0xad/0x1a0 kernel: [ 154.522737] ksys_write+0xa4/0xe0 kernel: [ 154.522745] do_syscall_64+0x64/0x2b0 kernel: [ 154.522748] entry_SYSCALL_64_after_hwframe+0x49/0xbe kernel: [ 154.522749] kernel: [ 154.522749] -> #3 (&mddev->reconfig_mutex){+.+.}: kernel: [ 154.522752] __mutex_lock+0x87/0x950 kernel: [ 154.522756] new_dev_store+0xc9/0x210 [md_mod] kernel: [ 154.522759] md_attr_store+0x7a/0xc0 [md_mod] kernel: [ 154.522761] kernfs_fop_write+0x117/0x1b0 kernel: [ 154.522763] vfs_write+0xad/0x1a0 kernel: [ 154.522765] ksys_write+0xa4/0xe0 kernel: [ 154.522767] do_syscall_64+0x64/0x2b0 kernel: [ 154.522769] entry_SYSCALL_64_after_hwframe+0x49/0xbe kernel: [ 154.522770] kernel: [ 154.522770] -> #2 (kn->count#253){++++}: kernel: [ 154.522775] __kernfs_remove+0x253/0x2c0 kernel: [ 154.522778] kernfs_remove+0x1f/0x30 kernel: [ 154.522780] kobject_del+0x28/0x60 kernel: [ 154.522783] mddev_delayed_delete+0x24/0x30 [md_mod] kernel: [ 154.522786] process_one_work+0x2a7/0x5f0 kernel: [ 154.522788] worker_thread+0x2d/0x3d0 kernel: [ 154.522793] kthread+0x117/0x130 kernel: [ 154.522795] ret_from_fork+0x3a/0x50 kernel: [ 154.522796] kernel: [ 154.522796] -> #1 ((work_completion)(&mddev->del_work)){+.+.}: kernel: [ 154.522800] process_one_work+0x27e/0x5f0 kernel: [ 154.522802] worker_thread+0x2d/0x3d0 kernel: [ 154.522804] kthread+0x117/0x130 kernel: [ 154.522806] ret_from_fork+0x3a/0x50 kernel: [ 154.522807] kernel: [ 154.522807] -> #0 ((wq_completion)md_misc){+.+.}: kernel: [ 154.522813] __lock_acquire+0x1392/0x1690 kernel: [ 154.522816] lock_acquire+0xb4/0x1a0 kernel: [ 154.522818] flush_workqueue+0xab/0x4b0 kernel: [ 154.522821] md_open+0xb6/0xc0 [md_mod] kernel: [ 154.522823] __blkdev_get+0xea/0x590 kernel: [ 154.522825] blkdev_get+0x65/0x140 kernel: [ 154.522828] do_dentry_open+0x1d1/0x380 kernel: [ 154.522831] path_openat+0x567/0xcc0 kernel: [ 154.522834] do_filp_open+0x9b/0x110 kernel: [ 154.522836] do_sys_openat2+0x201/0x2a0 kernel: [ 154.522838] do_sys_open+0x57/0x80 kernel: [ 154.522840] do_syscall_64+0x64/0x2b0 kernel: [ 154.522842] entry_SYSCALL_64_after_hwframe+0x49/0xbe kernel: [ 154.522844] kernel: [ 154.522844] other info that might help us debug this: kernel: [ 154.522844] kernel: [ 154.522846] Chain exists of: kernel: [ 154.522846] (wq_completion)md_misc --> &mddev->reconfig_mutex --> &bdev->bd_mutex kernel: [ 154.522846] kernel: [ 154.522850] Possible unsafe locking scenario: kernel: [ 154.522850] kernel: [ 154.522852] CPU0 CPU1 kernel: [ 154.522853] ---- ---- kernel: [ 154.522854] lock(&bdev->bd_mutex); kernel: [ 154.522856] lock(&mddev->reconfig_mutex); kernel: [ 154.522858] lock(&bdev->bd_mutex); kernel: [ 154.522860] lock((wq_completion)md_misc); kernel: [ 154.522861] kernel: [ 154.522861] *** DEADLOCK *** kernel: [ 154.522861] kernel: [ 154.522864] 1 lock held by mdadm/2482: kernel: [ 154.522865] #0: ffff88804efa9338 (&bdev->bd_mutex){+.+.}, at: __blkdev_get+0x79/0x590 kernel: [ 154.522868] kernel: [ 154.522868] stack backtrace: kernel: [ 154.522873] CPU: 1 PID: 2482 Comm: mdadm Tainted: G O 5.6.0-rc7-lp151.27-default #25 kernel: [ 154.522875] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014 kernel: [ 154.522878] Call Trace: kernel: [ 154.522881] dump_stack+0x8f/0xcb kernel: [ 154.522884] check_noncircular+0x194/0x1b0 kernel: [ 154.522888] ? __lock_acquire+0x1392/0x1690 kernel: [ 154.522890] __lock_acquire+0x1392/0x1690 kernel: [ 154.522893] lock_acquire+0xb4/0x1a0 kernel: [ 154.522895] ? flush_workqueue+0x84/0x4b0 kernel: [ 154.522898] flush_workqueue+0xab/0x4b0 kernel: [ 154.522900] ? flush_workqueue+0x84/0x4b0 kernel: [ 154.522905] ? md_open+0xb6/0xc0 [md_mod] kernel: [ 154.522908] md_open+0xb6/0xc0 [md_mod] kernel: [ 154.522910] __blkdev_get+0xea/0x590 kernel: [ 154.522912] ? bd_acquire+0xc0/0xc0 kernel: [ 154.522914] blkdev_get+0x65/0x140 kernel: [ 154.522916] ? bd_acquire+0xc0/0xc0 kernel: [ 154.522918] do_dentry_open+0x1d1/0x380 kernel: [ 154.522921] path_openat+0x567/0xcc0 kernel: [ 154.522923] ? __lock_acquire+0x380/0x1690 kernel: [ 154.522926] do_filp_open+0x9b/0x110 kernel: [ 154.522929] ? __alloc_fd+0xe5/0x1f0 kernel: [ 154.522935] ? kmem_cache_alloc+0x28c/0x630 kernel: [ 154.522939] ? do_sys_openat2+0x201/0x2a0 kernel: [ 154.522941] do_sys_openat2+0x201/0x2a0 kernel: [ 154.522944] do_sys_open+0x57/0x80 kernel: [ 154.522946] do_syscall_64+0x64/0x2b0 kernel: [ 154.522948] entry_SYSCALL_64_after_hwframe+0x49/0xbe kernel: [ 154.522951] RIP: 0033:0x7f98d279d9ae And md_alloc also flushed the same workqueue, but the thing is different here. Because all the paths call md_alloc don't hold bdev->bd_mutex, and the flush is necessary to avoid race condition, so leave it as it is. Signed-off-by:
Guoqing Jiang <guoqing.jiang@cloud.ionos.com> Signed-off-by:
Song Liu <songliubraving@fb.com> Signed-off-by:
Sasha Levin <sashal@kernel.org> Signed-off-by:
Kamal Mostafa <kamal@canonical.com> Signed-off-by:
Khalid Elmously <khalid.elmously@canonical.com>
-
Daniel Thompson authored
BugLink: https://bugs.launchpad.net/bugs/1884564 [ Upstream commit 3fec4aec ] Currently there is a small window where a badly timed migration could cause in_dbg_master() to spuriously return true. Specifically if we migrate to a new core after reading the processor id and the previous core takes a breakpoint then we will evaluate true if we read kgdb_active before we get the IPI to bring us to halt. Fix this by checking irqs_disabled() first. Interrupts are always disabled when we are executing the kgdb trap so this is an acceptable prerequisite. This also allows us to replace raw_smp_processor_id() with smp_processor_id() since the short circuit logic will prevent warnings from PREEMPT_DEBUG. Fixes: dcc78711 ("kgdb: core changes to support kdb") Suggested-by:
Will Deacon <will@kernel.org> Link: https://lore.kernel.org/r/20200506164223.2875760-1-daniel.thompson@linaro.orgReviewed-by:
Douglas Anderson <dianders@chromium.org> Signed-off-by:
Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by:
-
Serge Semin authored
BugLink: https://bugs.launchpad.net/bugs/1884564 [ Upstream commit 8a0efb8b ] Commit 3885c2b4 ("MIPS: CM: Add support for reporting CM cache errors") adds cm2_causes[] array with map of error type ID and pointers to the short description string. There is a mistake in the table, since according to MIPS32 manual CM2_ERROR_TYPE = {17,18} correspond to INTVN_WR_ERR and INTVN_RD_ERR, while the table claims they have {0x17,0x18} codes. This is obviously hex-dec copy-paste bug. Moreover codes {0x18 - 0x1a} indicate L2 ECC errors. Fixes: 3885c2b4 ("MIPS: CM: Add support for reporting CM cache errors") Signed-off-by:
Serge Semin <Sergey.Semin@baikalelectronics.ru> Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru> Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de> Cc: Paul Burton <paulburton@kernel.org> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Arnd Bergmann <arnd@arndb.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: linux-pm@vger.kernel.org Cc: devicetree@vger.kernel.org Signed-off-by:
Thomas Bogendoerfer <tsbogend@alpha.franken.de> Signed-off-by:
-
Jeremy Kerr authored
BugLink: https://bugs.launchpad.net/bugs/1884564 [ Upstream commit 88413a6b ] Currently, we may perform a copy_to_user (through simple_read_from_buffer()) while holding a context's register_lock, while accessing the context save area. This change uses a temporary buffer for the context save area data, which we then pass to simple_read_from_buffer. Includes changes from Christoph Hellwig <hch@lst.de>. Fixes: bf1ab978 ("[POWERPC] coredump: Add SPU elf notes to coredump.") Signed-off-by:
Jeremy Kerr <jk@ozlabs.org> Reviewed-by:
Arnd Bergmann <arnd@arndb.de> [hch: renamed to function to avoid ___-prefixes] Signed-off-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Yunjian Wang authored
BugLink: https://bugs.launchpad.net/bugs/1884564 [ Upstream commit 09f6c44a ] The method ndo_start_xmit() returns a value of type netdev_tx_t. Fix the ndo function to use the correct type. And emac_start_xmit() can leak one skb if 'channel' == 3. Signed-off-by:
Yunjian Wang <wangyunjian@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Wei Yongjun authored
BugLink: https://bugs.launchpad.net/bugs/1884564 [ Upstream commit 88ec7cb2 ] Fix to return a negative error code from the error handling case instead of 0, as done elsewhere in this function. Fixes: b7370112 ("lpc32xx: Added ethernet driver") Signed-off-by:
Wei Yongjun <weiyongjun1@huawei.com> Acked-by:
Vladimir Zapolskiy <vz@mleia.com> Signed-off-by:
-
Nathan Chancellor authored
BugLink: https://bugs.launchpad.net/bugs/1884564 [ Upstream commit 18f1ca46 ] When building 64r6_defconfig with CONFIG_MIPS32_O32 disabled and CONFIG_CRYPTO_RSA enabled: lib/mpi/generic_mpih-mul1.c:37:24: error: invalid use of a cast in a inline asm context requiring an l-value: remove the cast or build with -fheinous-gnu-extensions umul_ppmm(prod_high, prod_low, s1_ptr[j], s2_limb); ~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~ lib/mpi/longlong.h:664:22: note: expanded from macro 'umul_ppmm' : "=d" ((UDItype)(w0)) ~~~~~~~~~~^~~ lib/mpi/generic_mpih-mul1.c:37:13: error: invalid use of a cast in a inline asm context requiring an l-value: remove the cast or build with -fheinous-gnu-extensions umul_ppmm(prod_high, prod_low, s1_ptr[j], s2_limb); ~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ lib/mpi/longlong.h:668:22: note: expanded from macro 'umul_ppmm' : "=d" ((UDItype)(w1)) ~~~~~~~~~~^~~ 2 errors generated. This special case for umul_ppmm for MIPS64r6 was added in commit bbc25bee ("lib/mpi: Fix umul_ppmm() for MIPS64r6"), due to GCC being inefficient and emitting a __multi3 intrinsic. There is no such issue with clang; with this patch applied, I can build this configuration without any problems and there are no link errors like mentioned in the commit above (which I can still reproduce with GCC 9.3.0 when that commit is reverted). Only use this definition when GCC is being used. This really should have been caught by commit b0c091ae ("lib/mpi: Eliminate unused umul_ppmm definitions for MIPS") when I was messing around in this area but I was not testing 64-bit MIPS at the time. Link: https://github.com/ClangBuiltLinux/linux/issues/885Reported-by:
Dmitry Golovin <dima@golovin.in> Signed-off-by:
Nathan Chancellor <natechancellor@gmail.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Pablo Neira Ayuso authored
BugLink: https://bugs.launchpad.net/bugs/1884564 [ Upstream commit 0d7c8346 ] Instead of EINVAL which should be used for malformed netlink messages. Fixes: eb31628e ("netfilter: nf_tables: Add support for IPv6 NAT") Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by:
-
Tiezhu Yang authored
BugLink: https://bugs.launchpad.net/bugs/1884564 [ Upstream commit 269b3a9a ] In the current code, if CONFIG_SWIOTLB is set, when failed to get IO TLB memory from the low pages by plat_swiotlb_setup(), it may lead to the boot process failed with kernel panic. (1) On the Loongson and SiByte platform arch/mips/loongson64/dma.c arch/mips/sibyte/common/dma.c void __init plat_swiotlb_setup(void) { swiotlb_init(1); } kernel/dma/swiotlb.c void __init swiotlb_init(int verbose) { ... vstart = memblock_alloc_low(PAGE_ALIGN(bytes), PAGE_SIZE); if (vstart && !swiotlb_init_with_tbl(vstart, io_tlb_nslabs, verbose)) return; ... pr_warn("Cannot allocate buffer"); no_iotlb_memory = true; } phys_addr_t swiotlb_tbl_map_single() { ... if (no_iotlb_memory) panic("Can not allocate SWIOTLB buffer earlier ..."); ... } (2) On the Cavium OCTEON platform arch/mips/cavium-octeon/dma-octeon.c void __init plat_swiotlb_setup(void) { ... octeon_swiotlb = memblock_alloc_low(swiotlbsize, PAGE_SIZE); if (!octeon_swiotlb) panic("%s: Failed to allocate %zu bytes align=%lx\n", __func__, swiotlbsize, PAGE_SIZE); ... } Because IO_TLB_DEFAULT_SIZE is 64M, if the rest size of low memory is less than 64M when call plat_swiotlb_setup(), we can easily reproduce the panic case. In order to reduce the possibility of kernel panic when failed to get IO TLB memory under CONFIG_SWIOTLB, it is better to allocate low memory as small as possible before plat_swiotlb_setup(), so make sparse_init() using top-down allocation. Reported-by:
Juxin Gao <gaojuxin@loongson.cn> Co-developed-by:
Tiezhu Yang <yangtiezhu@loongson.cn> Signed-off-by:
-
Colin Ian King authored
BugLink: https://bugs.launchpad.net/bugs/1884564 [ Upstream commit 96f3a939 ] Currently when i2c transfers fail the error return -EREMOTEIO is assigned to err but then later overwritten when the tuner attach call is made. Fix this by returning early with the error return code -EREMOTEIO on i2c transfer failure errors. If the transfer fails, an uninitialized value will be read from b2. Addresses-Coverity: ("Unused value") Fixes: fbfee868 ("V4L/DVB (5651): Dibusb-mb: convert pll handling to properly use dvb-pll") Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
Sean Young <sean@mess.org> Signed-off-by:
Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by:
-
Kees Cook authored
BugLink: https://bugs.launchpad.net/bugs/1884564 [ Upstream commit a34c7f51 ] Variables declared in a switch statement before any case statements cannot be automatically initialized with compiler instrumentation (as they are not part of any execution flow). With GCC's proposed automatic stack variable initialization feature, this triggers a warning (and they don't get initialized). Clang's automatic stack variable initialization (via CONFIG_INIT_STACK_ALL=y) doesn't throw a warning, but it also doesn't initialize such variables[1]. Note that these warnings (or silent skipping) happen before the dead-store elimination optimization phase, so even when the automatic initializations are later elided in favor of direct initializations, the warnings remain. To avoid these problems, move such variables into the "case" where they're used or lift them up into the main function body. drivers/net/ethernet/intel/e1000/e1000_main.c: In function ‘e1000_xmit_frame’: drivers/net/ethernet/intel/e1000/e1000_main.c:3143:18: warning: statement will never be executed [-Wswitch-unreachable] 3143 | unsigned int pull_size; | ^~~~~~~~~ [1] https://bugs.llvm.org/show_bug.cgi?id=44916Signed-off-by:
Kees Cook <keescook@chromium.org> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by:
-
Christoph Hellwig authored
BugLink: https://bugs.launchpad.net/bugs/1884564 [ Upstream commit 5bf99174 ] vm_map_ram can keep mappings around after the vm_unmap_ram. Using that with non-PAGE_KERNEL mappings can lead to all kinds of aliasing issues. Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Acked-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Christian Borntraeger <borntraeger@de.ibm.com> Cc: Christophe Leroy <christophe.leroy@c-s.fr> Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Cc: David Airlie <airlied@linux.ie> Cc: Gao Xiang <xiang@kernel.org> Cc: Haiyang Zhang <haiyangz@microsoft.com> Cc: Johannes Weiner <hannes@cmpxchg.org> Cc: "K. Y. Srinivasan" <kys@microsoft.com> Cc: Laura Abbott <labbott@redhat.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Michael Kelley <mikelley@microsoft.com> Cc: Minchan Kim <minchan@kernel.org> Cc: Nitin Gupta <ngupta@vflare.org> Cc: Robin Murphy <robin.murphy@arm.com> Cc: Sakari Ailus <sakari.ailus@linux.intel.com> Cc: Stephen Hemminger <sthemmin@microsoft.com> Cc: Sumit Semwal <sumit.semwal@linaro.org> Cc: Wei Liu <wei.liu@kernel.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: Catalin Marinas <catalin.marinas@arm.com> Cc: Heiko Carstens <heiko.carstens@de.ibm.com> Cc: Paul Mackerras <paulus@ozlabs.org> Cc: Vasily Gorbik <gor@linux.ibm.com> Cc: Will Deacon <will@kernel.org> Link: http://lkml.kernel.org/r/20200414131348.444715-4-hch@lst.deSigned-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Jia-Ju Bai authored
BugLink: https://bugs.launchpad.net/bugs/1884564 [ Upstream commit 3e1c6846 ] The value adapter->rss_conf is stored in DMA memory, and it is assigned to rssConf, so rssConf->indTableSize can be modified at anytime by malicious hardware. Because rssConf->indTableSize is assigned to n, buffer overflow may occur when the code "rssConf->indTable[n]" is executed. To fix this possible bug, n is checked after being used. Signed-off-by:
Jia-Ju Bai <baijiaju1990@gmail.com> Signed-off-by:
-
Linus Walleij authored
BugLink: https://bugs.launchpad.net/bugs/1884564 [ Upstream commit e1de9438 ] Recent work with KASan exposed the folling hard-coded bitmask in arch/arm/mm/proc-macros.S: bic rd, sp, #8128 bic rd, rd, #63 This forms the bitmask 0x1FFF that is coinciding with (PAGE_SIZE << THREAD_SIZE_ORDER) - 1, this code was assuming that THREAD_SIZE is always 8K (8192). As KASan was increasing THREAD_SIZE_ORDER to 2, I ran into this bug. Fix it by this little oneline suggested by Ard: bic rd, sp, #(THREAD_SIZE - 1) & ~63 Where THREAD_SIZE is defined using THREAD_SIZE_ORDER. We have to also include <linux/const.h> since the THREAD_SIZE expands to use the _AC() macro. Cc: Ard Biesheuvel <ardb@kernel.org> Cc: Florian Fainelli <f.fainelli@gmail.com> Suggested-by:
Ard Biesheuvel <ardb@kernel.org> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by:
-
Filipe Manana authored
BugLink: https://bugs.launchpad.net/bugs/1884564 [ Upstream commit 7e4a3f7e ] We are currently treating any non-zero return value from btrfs_next_leaf() the same way, by going to the code that inserts a new checksum item in the tree. However if btrfs_next_leaf() returns an error (a value < 0), we should just stop and return the error, and not behave as if nothing has happened, since in that case we do not have a way to know if there is a next leaf or we are currently at the last leaf already. So fix that by returning the error from btrfs_next_leaf(). Signed-off-by:
Filipe Manana <fdmanana@suse.com> Reviewed-by:
David Sterba <dsterba@suse.com> Signed-off-by:
-
Serge Semin authored
BugLink: https://bugs.launchpad.net/bugs/1884564 [ Upstream commit 6d2e16a3 ] Commit 10021488 ("clocksource: dw_apb_timer_of: use clocksource_of_init") replaced a publicly available driver initialization method with one called by the timer_probe() method available after CLKSRC_OF. In current implementation it traverses all the timers available in the system and calls their initialization methods if corresponding devices were either in dtb or in acpi. But if before the commit any number of available timers would be installed as clockevent and clocksource devices, after that there would be at most two. The rest are just ignored since default case branch doesn't do anything. I don't see a reason of such behaviour, neither the commit message explains it. Moreover this might be wrong if on some platforms these timers might be used for different purpose, as virtually CPU-local clockevent timers and as an independent broadcast timer. So in order to keep the compatibility with the platforms where the order of the timers detection has some meaning, lets add the secondly discovered timer to be of clocksource/sched_clock type, while the very first and the others would provide the clockevents service. Fixes: 10021488 ("clocksource: dw_apb_timer_of: use clocksource_of_init") Signed-off-by:
Daniel Lezcano <daniel.lezcano@linaro.org> Link: https://lore.kernel.org/r/20200521204818.25436-7-Sergey.Semin@baikalelectronics.ruSigned-off-by:
-
Serge Semin authored
BugLink: https://bugs.launchpad.net/bugs/1884564 [ Upstream commit 43dba9f3 ] It's pointless to track the Tx overrun interrupts if Rx-only SPI transfer is issued. Similarly there is no need in handling the Rx overrun/underrun interrupts if Tx-only SPI transfer is executed. So lets unmask the interrupts only if corresponding SPI transactions are implied. Co-developed-by:
Georgy Vlasov <Georgy.Vlasov@baikalelectronics.ru> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Douglas Anderson authored
BugLink: https://bugs.launchpad.net/bugs/1884564 [ Upstream commit 3ca676e4 ] If we detect that we recursively entered the debugger we should hack our I/O ops to NULL so that the panic() in the next line won't actually cause another recursion into the debugger. The first line of kgdb_panic() will check this and return. Signed-off-by:
-
Hsin-Yu Chao authored
BugLink: https://bugs.launchpad.net/bugs/1884564 [ Upstream commit 56b5453a ] Bluetooth PTS test case HFP/AG/ACC/BI-12-I accepts SCO connection with invalid parameter at the first SCO request expecting AG to attempt another SCO request with the use of "safe settings" for given codec, base on section 5.7.1.2 of HFP 1.7 specification. This patch addresses it by adding "Invalid LMP Parameters" (0x1e) to the SCO fallback case. Verified with below log: < HCI Command: Setup Synchronous Connection (0x01|0x0028) plen 17 Handle: 256 Transmit bandwidth: 8000 Receive bandwidth: 8000 Max latency: 13 Setting: 0x0003 Input Coding: Linear Input Data Format: 1's complement Input Sample Size: 8-bit # of bits padding at MSB: 0 Air Coding Format: Transparent Data Retransmission effort: Optimize for link quality (0x02) Packet type: 0x0380 3-EV3 may not be used 2-EV5 may not be used 3-EV5 may not be used > HCI Event: Command Status (0x0f) plen 4 Setup Synchronous Connection (0x01|0x0028) ncmd 1 Status: Success (0x00) > HCI Event: Number of Completed Packets (0x13) plen 5 Num handles: 1 Handle: 256 Count: 1 > HCI Event: Max Slots Change (0x1b) plen 3 Handle: 256 Max slots: 1 > HCI Event: Synchronous Connect Complete (0x2c) plen 17 Status: Invalid LMP Parameters / Invalid LL Parameters (0x1e) Handle: 0 Address: 00:1B:DC:F2:21:59 (OUI 00-1B-DC) Link type: eSCO (0x02) Transmission interval: 0x00 Retransmission window: 0x02 RX packet length: 0 TX packet length: 0 Air mode: Transparent (0x03) < HCI Command: Setup Synchronous Connection (0x01|0x0028) plen 17 Handle: 256 Transmit bandwidth: 8000 Receive bandwidth: 8000 Max latency: 8 Setting: 0x0003 Input Coding: Linear Input Data Format: 1's complement Input Sample Size: 8-bit # of bits padding at MSB: 0 Air Coding Format: Transparent Data Retransmission effort: Optimize for link quality (0x02) Packet type: 0x03c8 EV3 may be used 2-EV3 may not be used 3-EV3 may not be used 2-EV5 may not be used 3-EV5 may not be used > HCI Event: Command Status (0x0f) plen 4 Setup Synchronous Connection (0x01|0x0028) ncmd 1 Status: Success (0x00) > HCI Event: Max Slots Change (0x1b) plen 3 Handle: 256 Max slots: 5 > HCI Event: Max Slots Change (0x1b) plen 3 Handle: 256 Max slots: 1 > HCI Event: Synchronous Connect Complete (0x2c) plen 17 Status: Success (0x00) Handle: 257 Address: 00:1B:DC:F2:21:59 (OUI 00-1B-DC) Link type: eSCO (0x02) Transmission interval: 0x06 Retransmission window: 0x04 RX packet length: 30 TX packet length: 30 Air mode: Transparent (0x03) Signed-off-by:
Hsin-Yu Chao <hychao@chromium.org> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
-
Andy Shevchenko authored
BugLink: https://bugs.launchpad.net/bugs/1884564 [ Upstream commit 3cb97e22 ] Some DMA controller drivers do not tolerate non-zero values in the DMA configuration structures. Zero them to avoid issues with such DMA controller drivers. Even despite above this is a good practice per se. Fixes: 7063c0d9 ("spi/dw_spi: add DMA support") Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by:
Feng Tang <feng.tang@intel.com> Cc: Feng Tang <feng.tang@intel.com> Link: https://lore.kernel.org/r/20200506153025.21441-1-andriy.shevchenko@linux.intel.comSigned-off-by:
-
Xiaolong Huang authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit da2311a6 upstream. Uninitialized Kernel memory can leak to USB devices. Fix this by using kzalloc() instead of kmalloc(). Signed-off-by:
Xiaolong Huang <butterflyhuangxx@gmail.com> Fixes: 7259124e ("can: kvaser_usb: Split driver into kvaser_usb_core.c and kvaser_usb_leaf.c") Cc: linux-stable <stable@vger.kernel.org> # >= v4.19 Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> [bwh: Backported to 4.9: adjust filename, context] Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> Signed-off-by:
-
OGAWA Hirofumi authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit b1b65750 upstream. If FAT length == 0, the image doesn't have any data. And it can be the cause of overlapping the root dir and FAT entries. Also Windows treats it as invalid format. Reported-by: syzbot+6f1624f937d9d6911e2d@syzkaller.appspotmail.com Signed-off-by:
OGAWA Hirofumi <hirofumi@mail.parknet.co.jp> Signed-off-by:
-
Wang Hai authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit dde3c6b7 upstream. syzkaller reports for memory leak when kobject_init_and_add() returns an error in the function sysfs_slab_add() [1] When this happened, the function kobject_put() is not called for the corresponding kobject, which potentially leads to memory leak. This patch fixes the issue by calling kobject_put() even if kobject_init_and_add() fails. [1] BUG: memory leak unreferenced object 0xffff8880a6d4be88 (size 8): comm "syz-executor.3", pid 946, jiffies 4295772514 (age 18.396s) hex dump (first 8 bytes): 70 69 64 5f 33 00 ff ff pid_3... backtrace: kstrdup+0x35/0x70 mm/util.c:60 kstrdup_const+0x3d/0x50 mm/util.c:82 kvasprintf_const+0x112/0x170 lib/kasprintf.c:48 kobject_set_name_vargs+0x55/0x130 lib/kobject.c:289 kobject_add_varg lib/kobject.c:384 [inline] kobject_init_and_add+0xd8/0x170 lib/kobject.c:473 sysfs_slab_add+0x1d8/0x290 mm/slub.c:5811 __kmem_cache_create+0x50a/0x570 mm/slub.c:4384 create_cache+0x113/0x1e0 mm/slab_common.c:407 kmem_cache_create_usercopy+0x1a1/0x260 mm/slab_common.c:505 kmem_cache_create+0xd/0x10 mm/slab_common.c:564 create_pid_cachep kernel/pid_namespace.c:54 [inline] create_pid_namespace kernel/pid_namespace.c:96 [inline] copy_pid_ns+0x77c/0x8f0 kernel/pid_namespace.c:148 create_new_namespaces+0x26b/0xa30 kernel/nsproxy.c:95 unshare_nsproxy_namespaces+0xa7/0x1e0 kernel/nsproxy.c:229 ksys_unshare+0x3d2/0x770 kernel/fork.c:2969 __do_sys_unshare kernel/fork.c:3037 [inline] __se_sys_unshare kernel/fork.c:3035 [inline] __x64_sys_unshare+0x2d/0x40 kernel/fork.c:3035 do_syscall_64+0xa1/0x530 arch/x86/entry/common.c:295 Fixes: 80da026a ("mm/slub: fix slab double-free in case of duplicate sysfs filename") Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
Wang Hai <wanghai38@huawei.com> Signed-off-by:
-
Casey Schaufler authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit 84e99e58 upstream. Add barrier to soob. Return -EOVERFLOW if the buffer is exceeded. Suggested-by:
Hillf Danton <hdanton@sina.com> Reported-by: syzbot+bfdd4a2f07be52351350@syzkaller.appspotmail.com Signed-off-by:
Casey Schaufler <casey@schaufler-ca.com> Signed-off-by:
-
Qiujun Huang authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit 2bbcaaee upstream. In ath9k_hif_usb_rx_cb interface number is assumed to be 0. usb_ifnum_to_if(urb->dev, 0) But it isn't always true. The case reported by syzbot: https://lore.kernel.org/linux-usb/000000000000666c9c05a1c05d12@google.com usb 2-1: new high-speed USB device number 2 using dummy_hcd usb 2-1: config 1 has an invalid interface number: 2 but max is 0 usb 2-1: config 1 has no interface number 0 usb 2-1: New USB device found, idVendor=0cf3, idProduct=9271, bcdDevice= 1.08 usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 general protection fault, probably for non-canonical address 0xdffffc0000000015: 0000 [#1] SMP KASAN KASAN: null-ptr-deref in range [0x00000000000000a8-0x00000000000000af] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.6.0-rc5-syzkaller #0 Call Trace __usb_hcd_giveback_urb+0x29a/0x550 drivers/usb/core/hcd.c:1650 usb_hcd_giveback_urb+0x368/0x420 drivers/usb/core/hcd.c:1716 dummy_timer+0x1258/0x32ae drivers/usb/gadget/udc/dummy_hcd.c:1966 call_timer_fn+0x195/0x6f0 kernel/time/timer.c:1404 expire_timers kernel/time/timer.c:1449 [inline] __run_timers kernel/time/timer.c:1773 [inline] __run_timers kernel/time/timer.c:1740 [inline] run_timer_softirq+0x5f9/0x1500 kernel/time/timer.c:1786 __do_softirq+0x21e/0x950 kernel/softirq.c:292 invoke_softirq kernel/softirq.c:373 [inline] irq_exit+0x178/0x1a0 kernel/softirq.c:413 exiting_irq arch/x86/include/asm/apic.h:546 [inline] smp_apic_timer_interrupt+0x141/0x540 arch/x86/kernel/apic/apic.c:1146 apic_timer_interrupt+0xf/0x20 arch/x86/entry/entry_64.S:829 Reported-and-tested-by: syzbot+40d5d2e8a4680952f042@syzkaller.appspotmail.com Signed-off-by:
Qiujun Huang <hqjagain@gmail.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200404041838.10426-6-hqjagain@gmail.comSigned-off-by:
-
Qiujun Huang authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit 19d6c375 upstream. Add barrier to accessing the stack array skb_pool. The case reported by syzbot: https://lore.kernel.org/linux-usb/0000000000003d7c1505a2168418@google.com BUG: KASAN: stack-out-of-bounds in ath9k_hif_usb_rx_stream drivers/net/wireless/ath/ath9k/hif_usb.c:626 [inline] BUG: KASAN: stack-out-of-bounds in ath9k_hif_usb_rx_cb+0xdf6/0xf70 drivers/net/wireless/ath/ath9k/hif_usb.c:666 Write of size 8 at addr ffff8881db309a28 by task swapper/1/0 Call Trace: ath9k_hif_usb_rx_stream drivers/net/wireless/ath/ath9k/hif_usb.c:626 [inline] ath9k_hif_usb_rx_cb+0xdf6/0xf70 drivers/net/wireless/ath/ath9k/hif_usb.c:666 __usb_hcd_giveback_urb+0x1f2/0x470 drivers/usb/core/hcd.c:1648 usb_hcd_giveback_urb+0x368/0x420 drivers/usb/core/hcd.c:1713 dummy_timer+0x1258/0x32ae drivers/usb/gadget/udc/dummy_hcd.c:1966 call_timer_fn+0x195/0x6f0 kernel/time/timer.c:1404 expire_timers kernel/time/timer.c:1449 [inline] __run_timers kernel/time/timer.c:1773 [inline] __run_timers kernel/time/timer.c:1740 [inline] run_timer_softirq+0x5f9/0x1500 kernel/time/timer.c:1786 Reported-and-tested-by: syzbot+d403396d4df67ad0bd5f@syzkaller.appspotmail.com Signed-off-by:
-
Qiujun Huang authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit e4ff08a4 upstream. Write out of slab bounds. We should check epid. The case reported by syzbot: https://lore.kernel.org/linux-usb/0000000000006ac55b05a1c05d72@google.com BUG: KASAN: use-after-free in htc_process_conn_rsp drivers/net/wireless/ath/ath9k/htc_hst.c:131 [inline] BUG: KASAN: use-after-free in ath9k_htc_rx_msg+0xa25/0xaf0 drivers/net/wireless/ath/ath9k/htc_hst.c:443 Write of size 2 at addr ffff8881cea291f0 by task swapper/1/0 Call Trace: htc_process_conn_rsp drivers/net/wireless/ath/ath9k/htc_hst.c:131 [inline] ath9k_htc_rx_msg+0xa25/0xaf0 drivers/net/wireless/ath/ath9k/htc_hst.c:443 ath9k_hif_usb_reg_in_cb+0x1ba/0x630 drivers/net/wireless/ath/ath9k/hif_usb.c:718 __usb_hcd_giveback_urb+0x29a/0x550 drivers/usb/core/hcd.c:1650 usb_hcd_giveback_urb+0x368/0x420 drivers/usb/core/hcd.c:1716 dummy_timer+0x1258/0x32ae drivers/usb/gadget/udc/dummy_hcd.c:1966 call_timer_fn+0x195/0x6f0 kernel/time/timer.c:1404 expire_timers kernel/time/timer.c:1449 [inline] __run_timers kernel/time/timer.c:1773 [inline] __run_timers kernel/time/timer.c:1740 [inline] run_timer_softirq+0x5f9/0x1500 kernel/time/timer.c:1786 Reported-and-tested-by: syzbot+b1c61e5f11be5782f192@syzkaller.appspotmail.com Signed-off-by:
-
Qiujun Huang authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit abeaa850 upstream. Free wmi later after cmd urb has been killed, as urb cb will access wmi. the case reported by syzbot: https://lore.kernel.org/linux-usb/0000000000000002fc05a1d61a68@google.com BUG: KASAN: use-after-free in ath9k_wmi_ctrl_rx+0x416/0x500 drivers/net/wireless/ath/ath9k/wmi.c:215 Read of size 1 at addr ffff8881cef1417c by task swapper/1/0 Call Trace: <IRQ> ath9k_wmi_ctrl_rx+0x416/0x500 drivers/net/wireless/ath/ath9k/wmi.c:215 ath9k_htc_rx_msg+0x2da/0xaf0 drivers/net/wireless/ath/ath9k/htc_hst.c:459 ath9k_hif_usb_reg_in_cb+0x1ba/0x630 drivers/net/wireless/ath/ath9k/hif_usb.c:718 __usb_hcd_giveback_urb+0x29a/0x550 drivers/usb/core/hcd.c:1650 usb_hcd_giveback_urb+0x368/0x420 drivers/usb/core/hcd.c:1716 dummy_timer+0x1258/0x32ae drivers/usb/gadget/udc/dummy_hcd.c:1966 call_timer_fn+0x195/0x6f0 kernel/time/timer.c:1404 expire_timers kernel/time/timer.c:1449 [inline] __run_timers kernel/time/timer.c:1773 [inline] __run_timers kernel/time/timer.c:1740 [inline] run_timer_softirq+0x5f9/0x1500 kernel/time/timer.c:1786 Reported-and-tested-by: syzbot+5d338854440137ea0fef@syzkaller.appspotmail.com Signed-off-by:
-
Marc Zyngier authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit 3204be41 upstream. AArch32 CP1x registers are overlayed on their AArch64 counterparts in the vcpu struct. This leads to an interesting problem as they are stored in their CPU-local format, and thus a CP1x register doesn't "hit" the lower 32bit portion of the AArch64 register on a BE host. To workaround this unfortunate situation, introduce a bias trick in the vcpu_cp1x() accessors which picks the correct half of the 64bit register. Cc: stable@vger.kernel.org Reported-by:
James Morse <james.morse@arm.com> Tested-by:
Marc Zyngier <maz@kernel.org> Signed-off-by:
-
Sean Christopherson authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit 2ebac8bb upstream. Consult only the basic exit reason, i.e. bits 15:0 of vmcs.EXIT_REASON, when determining whether a nested VM-Exit should be reflected into L1 or handled by KVM in L0. For better or worse, the switch statement in nested_vmx_exit_reflected() currently defaults to "true", i.e. reflects any nested VM-Exit without dedicated logic. Because the case statements only contain the basic exit reason, any VM-Exit with modifier bits set will be reflected to L1, even if KVM intended to handle it in L0. Practically speaking, this only affects EXIT_REASON_MCE_DURING_VMENTRY, i.e. a #MC that occurs on nested VM-Enter would be incorrectly routed to L1, as "failed VM-Entry" is the only modifier that KVM can currently encounter. The SMM modifiers will never be generated as KVM doesn't support/employ a SMI Transfer Monitor. Ditto for "exit from enclave", as KVM doesn't yet support virtualizing SGX, i.e. it's impossible to enter an enclave in a KVM guest (L1 or L2). Fixes: 644d711a ("KVM: nVMX: Deciding if L0 or L1 should handle an L2 exit") Cc: Jim Mattson <jmattson@google.com> Cc: Xiaoyao Li <xiaoyao.li@intel.com> Cc: stable@vger.kernel.org Signed-off-by:
Sean Christopherson <sean.j.christopherson@intel.com> Message-Id: <20200227174430.26371-1-sean.j.christopherson@intel.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Paolo Bonzini authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit 6c0238c4 upstream. Restoring the ASID from the hsave area on VMEXIT is wrong, because its value depends on the handling of TLB flushes. Just skipping the field in copy_vmcb_control_area will do. Cc: stable@vger.kernel.org Signed-off-by:
-
Christophe JAILLET authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit 18722d48 upstream. Some memory is vmalloc'ed in the 'w100fb_save_vidmem' function and freed in the 'w100fb_restore_vidmem' function. (these functions are called respectively from the 'suspend' and the 'resume' functions) However, it is also freed in the 'remove' function. In order to avoid a potential double free, set the corresponding pointer to NULL once freed in the 'w100fb_restore_vidmem' function. Fixes: aac51f09 ("[PATCH] w100fb: Rewrite for platform independence") Cc: Richard Purdie <rpurdie@rpsys.net> Cc: Antonino Daplas <adaplas@pol.net> Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Cc: <stable@vger.kernel.org> # v2.6.14+ Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by:
Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20200506181902.193290-1-christophe.jaillet@wanadoo.frSigned-off-by:
-
Eric W. Biederman authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit ef1548ad upstream. Recently syzbot reported that unmounting proc when there is an ongoing inotify watch on the root directory of proc could result in a use after free when the watch is removed after the unmount of proc when the watcher exits. Commit 69879c01 ("proc: Remove the now unnecessary internal mount of proc") made it easier to unmount proc and allowed syzbot to see the problem, but looking at the code it has been around for a long time. Looking at the code the fsnotify watch should have been removed by fsnotify_sb_delete in generic_shutdown_super. Unfortunately the inode was allocated with new_inode_pseudo instead of new_inode so the inode was not on the sb->s_inodes list. Which prevented fsnotify_unmount_inodes from finding the inode and removing the watch as well as made it so the "VFS: Busy inodes after unmount" warning could not find the inodes to warn about them. Make all of the inodes in proc visible to generic_shutdown_super, and fsnotify_sb_delete by using new_inode instead of new_inode_pseudo. The only functional difference is that new_inode places the inodes on the sb->s_inodes list. I wrote a small test program and I can verify that without changes it can trigger this issue, and by replacing new_inode_pseudo with new_inode the issues goes away. Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/000000000000d788c905a7dfa3f4@google.com Reported-by: syzbot+7d2debdcdb3cb93c1e5e@syzkaller.appspotmail.com Fixes: 0097875b ("proc: Implement /proc/thread-self to point at the directory of the current thread") Fixes: 021ada7d ("procfs: switch /proc/self away from proc_dir_entry") Fixes: 51f0885e ("vfs,proc: guarantee unique inodes in /proc") Signed-off-by:
"Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by:
-
Yuxuan Shui authored
BugLink: https://bugs.launchpad.net/bugs/1884564 commit 520da69d upstream. In ovl_copy_xattr, if all the xattrs to be copied are overlayfs private xattrs, the copy loop will terminate without assigning anything to the error variable, thus returning an uninitialized value. If ovl_copy_xattr is called from ovl_clear_empty, this uninitialized error value is put into a pointer by ERR_PTR(), causing potential invalid memory accesses down the line. This commit initialize error with 0. This is the correct value because when there's no xattr to copy, because all xattrs are private, ovl_copy_xattr should succeed. This bug is discovered with the help of INIT_STACK_ALL and clang. Signed-off-by:
Yuxuan Shui <yshuiv7@gmail.com> Link: https://bugs.chromium.org/p/chromium/issues/detail?id=1050405 Fixes: 0956254a ("ovl: don't copy up opaqueness") Cc: stable@vger.kernel.org # v4.8 Signed-off-by:
Alexander Potapenko <glider@google.com> Signed-off-by:
Miklos Szeredi <mszeredi@redhat.com> Signed-off-by:
-
Lukas Wunner authored
BugLink: https://bugs.launchpad.net/bugs/1884564 [ Upstream commit 9dd277ff ] The BCM2835 SPI driver uses devm_spi_register_controller() on bind. As a consequence, on unbind, __device_release_driver() first invokes bcm2835_spi_remove() before unregistering the SPI controller via devres_release_all(). This order is incorrect: bcm2835_spi_remove() tears down the DMA channels and turns off the SPI controller, including its interrupts and clock. The SPI controller is thus no longer usable. When the SPI controller is subsequently unregistered, it unbinds all its slave devices. If their drivers need to access the SPI bus, e.g. to quiesce their interrupts, unbinding will fail. As a rule, devm_spi_register_controller() must not be used if the ->remove() hook performs teardown steps which shall be performed after unbinding of slaves. Fix by using the non-devm variant spi_register_controller(). Note that the struct spi_controller as well as the driver-private data are not freed until after bcm2835_spi_remove() has finished, so accessing them is safe. Fixes: 247263db ("spi: bcm2835: use devm_spi_register_master()") Signed-off-by:
Lukas Wunner <lukas@wunner.de> Cc: stable@vger.kernel.org # v3.13+ Link: https://lore.kernel.org/r/2397dd70cdbe95e0bc4da2b9fca0f31cb94e5aed.1589557526.git.lukas@wunner.deSigned-off-by:
-
Lukas Wunner authored
BugLink: https://bugs.launchpad.net/bugs/1884564 [ Upstream commit 32e5b572 ] The PXA2xx SPI driver uses devm_spi_register_controller() on bind. As a consequence, on unbind, __device_release_driver() first invokes pxa2xx_spi_remove() before unregistering the SPI controller via devres_release_all(). This order is incorrect: pxa2xx_spi_remove() disables the chip, rendering the SPI bus inaccessible even though the SPI controller is still registered. When the SPI controller is subsequently unregistered, it unbinds all its slave devices. Because their drivers cannot access the SPI bus, e.g. to quiesce interrupts, the slave devices may be left in an improper state. As a rule, devm_spi_register_controller() must not be used if the ->remove() hook performs teardown steps which shall be performed after unregistering the controller and specifically after unbinding of slaves. Fix by reverting to the non-devm variant of spi_register_controller(). An alternative approach would be to use device-managed functions for all steps in pxa2xx_spi_remove(), e.g. by calling devm_add_action_or_reset() on probe. However that approach would add more LoC to the driver and it wouldn't lend itself as well to backporting to stable. The improper use of devm_spi_register_controller() was introduced in 2013 by commit a807fcd0 ("spi: pxa2xx: use devm_spi_register_master()"), but all earlier versions of the driver going back to 2006 were likewise broken because they invoked spi_unregister_master() at the end of pxa2xx_spi_remove(), rather than at the beginning. Fixes: e0c9905e ("[PATCH] SPI: add PXA2xx SSP SPI Driver") Signed-off-by:
-
Lukas Wunner authored
BugLink: https://bugs.launchpad.net/bugs/1884564 [ Upstream commit 84855678 ] When an SPI controller unregisters, it unbinds all its slave devices. For this, their drivers may need to access the SPI bus, e.g. to quiesce interrupts. However since commit ffbbdd21 ("spi: create a message queueing infrastructure"), spi_destroy_queue() is executed before unbinding the slaves. It sets ctlr->running = false, thereby preventing SPI bus access and causing unbinding of slave devices to fail. Fix by unbinding slaves before calling spi_destroy_queue(). Fixes: ffbbdd21 ("spi: create a message queueing infrastructure") Signed-off-by:
-
Andy Shevchenko authored
BugLink: https://bugs.launchpad.net/bugs/1884564 [ Upstream commit ebc37af5 ] The device_for_each_child() doesn't require the returned value to be checked. Thus, drop the dummy variable completely and have no warning anymore: drivers/spi/spi.c: In function ‘spi_unregister_controller’: drivers/spi/spi.c:2480:6: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable] int dummy; ^~~~~ Signed-off-by:
-
Lukas Wunner authored
BugLink: https://bugs.launchpad.net/bugs/1884564 [ Upstream commit ca8b19d6 ] The Designware SPI driver uses devm_spi_register_controller() on bind. As a consequence, on unbind, __device_release_driver() first invokes dw_spi_remove_host() before unregistering the SPI controller via devres_release_all(). This order is incorrect: dw_spi_remove_host() shuts down the chip, rendering the SPI bus inaccessible even though the SPI controller is still registered. When the SPI controller is subsequently unregistered, it unbinds all its slave devices. Because their drivers cannot access the SPI bus, e.g. to quiesce interrupts, the slave devices may be left in an improper state. As a rule, devm_spi_register_controller() must not be used if the ->remove() hook performs teardown steps which shall be performed after unregistering the controller and specifically after unbinding of slaves. Fix by reverting to the non-devm variant of spi_register_controller(). An alternative approach would be to use device-managed functions for all steps in dw_spi_remove_host(), e.g. by calling devm_add_action_or_reset() on probe. However that approach would add more LoC to the driver and it wouldn't lend itself as well to backporting to stable. Fixes: 04f421e7 ("spi: dw: use managed resources") Signed-off-by:
-
Sasha Levin authored
BugLink: https://bugs.launchpad.net/bugs/1884564 [ Upstream commit 66b19d76 ] It is possible to get an interrupt as soon as it is requested. dw_spi_irq does spi_controller_get_devdata(master) and expects it to be different than NULL. However, spi_controller_set_devdata() is called after request_irq(), resulting in the following crash: CPU 0 Unable to handle kernel paging request at virtual address 00000030, epc == 8058e09c, ra == 8018ff90 [...] Call Trace: [<8058e09c>] dw_spi_irq+0x8/0x64 [<8018ff90>] __handle_irq_event_percpu+0x70/0x1d4 [<80190128>] handle_irq_event_percpu+0x34/0x8c [<801901c4>] handle_irq_event+0x44/0x80 [<801951a8>] handle_level_irq+0xdc/0x194 [<8018f580>] generic_handle_irq+0x38/0x50 [<804c6924>] ocelot_irq_handler+0x104/0x1c0 Signed-off-by:
Alexandre Belloni <alexandre.belloni@bootlin.com> Reviewed-by:
Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by:
-
