Make sure UART3, where the console is, is called ttyS2. That is
consistent with the early console.

Link: https://lore.kernel.org/r/20191031163455.1711872-5-lkundrak@v3.skSigned-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Olof Johansson <olof@lixom.net>

Ponted out by DTC:

  <stdout>: Warning (unit_address_vs_reg): /memory: node has a reg or ranges
  property, but no unit name

Link: https://lore.kernel.org/r/20191031163455.1711872-4-lkundrak@v3.skSigned-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Olof Johansson <olof@lixom.net>

There's a typo there that rightfully upsets DTS:

  <stdout>: Warning (simple_bus_reg): /soc/watchdog@2c000620: simple-bus
  unit address format error, expected "e0000620"

Link: https://lore.kernel.org/r/20191031163455.1711872-3-lkundrak@v3.skSigned-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Olof Johansson <olof@lixom.net>

It should have one and DTC is indeed unhappy about its absence:

  <stdout>: Warning (unit_address_vs_reg): /soc/clocks: node has a reg or
  ranges property, but no unit name

Link: https://lore.kernel.org/r/20191031163455.1711872-2-lkundrak@v3.skSigned-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Olof Johansson <olof@lixom.net>

Add GPIO controllers for RDA8810PL SoC. There are 4 GPIO controllers
in this SoC with maximum of 32 gpios. Except GPIOC, all controllers
are capable of generating edge/level interrupts from first 8 lines.

Link: https://lore.kernel.org/r/20191030101154.6312-2-manivannan.sadhasivam@linaro.orgSigned-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

ARM64: DT: Hisilicon SoCs DT updates for 5.5

- add Mali450 MP4 GPU node in the hi6220 SoC

* tag 'hisi-arm64-dt-for-5.5' of git://github.com/hisilicon/linux-hisi:
  arm64: dts: hisilicon: Add Mali-450 MP4 GPU DT entry

Link: https://lore.kernel.org/r/5DB95AAB.8060405@hisilicon.comSigned-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'realtek-arm64-dt-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-realtek into arm/dt

Realtek ARM64 based SoC DT for v5.5

Add RTD1293 and RTD1296 DTs. Add the watchdog for all of RTD129x DTs.
Add reset controllers for RTD129x and start using them for UARTs.

* tag 'realtek-arm64-dt-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-realtek:
  arm64: dts: realtek: Add RTD129x UART resets
  arm64: dts: realtek: Add RTD129x reset controller nodes
  dt-bindings: reset: Add Realtek RTD1295
  arm64: dts: realtek: Add watchdog node for RTD129x
  arm64: dts: realtek: Add oscillator for RTD129x
  arm64: dts: realtek: Add RTD1296 and Synology DS418
  dt-bindings: arm: realtek: Document RTD1296 and Synology DS418
  arm64: dts: realtek: Add RTD1293 and Synology DS418j
  arm64: dts: realtek: Change dual-license from MIT to BSD
  dt-bindings: arm: realtek: Document RTD1293 and Synology DS418j
  dt-bindings: arm: realtek: Tidy up conversion to json-schema

Link: https://lore.kernel.org/r/20191030041000.31848-2-afaerber@suse.deSigned-off-by: Olof Johansson <olof@lixom.net>

Merge branch 'for_5.5/keystone-dts' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into arm/dt

* 'for_5.5/keystone-dts' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
  ARM: configs: keystone: enable cpts
  ARM: dts: k2l-netcp: add cpts refclk_mux node
  ARM: dts: k2hk-netcp: add cpts refclk_mux node
  ARM: dts: k2e-netcp: add cpts refclk_mux node
  ARM: dts: k2e-clocks: add input ext. fixed clocks tsipclka/b
  ARM: dts: keystone-clocks: add input fixed clocks

Link: https://lore.kernel.org/r/1572372856-20598-2-git-send-email-santosh.shilimkar@oracle.comSigned-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'socfpga_dts_updates_for_v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into arm/dt

SoCFPGA DTS updates for v5.5
- Arria10
	- modify QSPI read-delay property
- Agilex
	- Add QSPI support
	- Enable USB and LEDs
	- Add service layer, fpga manager support
- Stratix10
	- Update QSPI reg address

* tag 'socfpga_dts_updates_for_v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
  arm64: dts: agilex: add service layer, fpga manager and fpga region
  arm64: agilex: enable USB and LEDs on agilex devkit
  arm64: dts: altera: update QSPI reg addresses for Stratix10
  arm64: dts: agilex: add QSPI support for Intel Agilex
  ARM: dts: arria10: Modify QSPI read_delay for Arria10

Link: https://lore.kernel.org/r/20191029143737.24850-1-dinguyen@kernel.orgSigned-off-by: Olof Johansson <olof@lixom.net>

Associate the UART nodes with the corresponding reset controller bits.
Signed-off-by: Andreas Färber <afaerber@suse.de>

Add nodes for the Realtek RTD1295 reset controllers.
Signed-off-by: Andreas Färber <afaerber@suse.de>

Add a header with symbolic reset indices for Realtek RTD1295 SoC.
Naming was derived from reset-names in an OEM's Device Tree.
Acked-by: Rob Herring <robh@kernel.org>
[AF: Dropped RTD1295 specific binding definition, updated SPDX]
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Andreas Färber <afaerber@suse.de>

Add the watchdog node to the RTD129x Device Tree.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
[AF: Moved from RTD1295 to new RTD129x]
Signed-off-by: Andreas Färber <afaerber@suse.de>

Add 27 MHz oscillator clock node.
Signed-off-by: Andreas Färber <afaerber@suse.de>

Add Device Trees for RTD1296 SoC and Synology DiskStation DS418.

Cc: info@synology.com
Signed-off-by: Andreas Färber <afaerber@suse.de>

Define compatible strings for Realtek RTD1296 SoC and Synology
DiskStation DS418 NAS.

Cc: info@synology.com
Acked-by: Rob Herring <robh@kernel.org>
[AF: Converted to json-schema]
Signed-off-by: Andreas Färber <afaerber@suse.de>

Add Device Trees for RTD1293 SoC and Synology DiskStation DS418j NAS.

Cc: info@synology.com
Signed-off-by: Andreas Färber <afaerber@suse.de>

Move the SPDX-License-Identifier to the top line and update to SPDX 2.0.
While at it, switch from GPLv2+/MIT to GPLv2+/BSD2c before adding more.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>

Define compatible strings for Realtek RTD1293 SoC and Synology
DiskStation DS418j NAS.

Cc: info@synology.com
Acked-by: Rob Herring <robh@kernel.org>
[AF: Converted to json-schema]
Signed-off-by: Andreas Färber <afaerber@suse.de>

Merge tag 'stm32-dt-for-v5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/dt

STM32 DT updates for v5.5, round 1

Highlights:
----------

MPU part:
 -Add and enable ADC support on stm32mp157a-dk1
 -Add DAC support on stm32mp157c-ed1
 -Add and enable VREFBUF support on stm32mp157a-dk1
 -Add focaltech touchscreen on stm32mp157c-dk2
 -Add hdmi support on stm32mp157a-dk1
 -Fix issues seen during YAML DT validation
 -Fix regulators issues for all MPU boards

MCU part:
 -Fix issues seen during YAML DT validation

* tag 'stm32-dt-for-v5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
  ARM: dts: stm32: remove useless dma-ranges property for stm32f469
  ARM: dts: stm32: remove useless dma-ranges property for stm32f429
  ARM: dts: stm32: disable active-discharge for vbus_otg on stm32mp157a-avenger96
  ARM: dts: stm32: Fix active discharge usage on stm32mp157
  ARM: dts: stm32: change default minimal buck1 value on stm32mp157
  ARM: dts: stm32: add PWR regulators support on stm32mp157
  ARM: dts: stm32: remove useless interrupt from dsi node for stm32f469
  ARM: dts: stm32: add hdmi audio support to stm32mp157a-dk1 board
  ARM: dts: stm32: Add DAC support to stm32mp157c-ed1
  ARM: dts: stm32: Add DAC pins used on stm32mp157c-ed1
  ARM: dts: stm32: fix regulator-sd_switch node on stm32mp157c-ed1 board
  ARM: dts: stm32: remove usb phy-names entries on stm32mp157c-ev1
  ARM: dts: stm32: fix joystick node on stm32f746 and stm32mp157c eval boards
  ARM: dts: stm32: fix memory nodes to match with DT validation tool
  ARM: dts: stm32: add focaltech touchscreen on stm32mp157c-dk2 board
  ARM: dts: stm32: enable ADC support on stm32mp157a-dk1
  ARM: dts: stm32: add ADC pins used on stm32mp157a-dk1
  ARM: dts: stm32: Enable VREFBUF on stm32mp157a-dk1
  ARM: dts: stm32: move ltdc pinctrl on stm32mp157a dk1 board

Link: https://lore.kernel.org/r/02c39510-f36d-abbb-c76f-49aff07c0a08@st.comSigned-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'juno-update-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/dt

ARMv8 Juno update for v5.5

Single patch to add support for Mali GPU on all versions of Juno.
Though it's disabled by default, it is very useful to test panfrost
drivers.

* tag 'juno-update-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
  arm64: dts: juno: add GPU subsystem

Link: https://lore.kernel.org/r/20191028040022.GC20568@e107533-lin.cambridge.arm.comSigned-off-by: Olof Johansson <olof@lixom.net>

Restore the device names for compatible strings as comments.
Prepare for adding more SoCs by inserting oneOf.

Fixes: 693af5f3 ("dt-bindings: arm: Convert Realtek board/soc bindings to json-schema")
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>

hi6220 has a Mali450 MP4 so lets add it into the DT.

Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>

Remove dma-ranges from ltdc node since it is already set
on bus node.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Remove dma-ranges from ltdc node since it is already set
on bus node.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Active discharge is not needed on vbus_otg and generate unneeded current
consumption.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Active discharge is a uint32 not a boolean.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Minimal value is the value set during boot or before suspend.
We must ensure that the value is a functional value to boot.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

This patch adds support of STM32 PWR regulators on
stm32mp157c. This replace dummy fixed regulators on
stm32mp157c-ed1 and stm32mp157c-dk2.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

DSI driver doesn't use interrupt, remove it from the node since it
breaks yaml check.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Add HDMI audio support through Sil9022 HDMI transceiver
on stm32mp157a-dk1 board.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

stm32mp157c-ed1 board has digital-to-analog converter signals routed
to JP11 and JP10 jumpers (e.g. PA4/PA5).
It's easier then to configure them both. But keep them disabled by default,
so the pins are kept in their initial state to lower power consumption.
This way they can also be used as GPIO.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Define pins that can be used by digital-to-analog converter on
stm32mp157c eval daughter board:
- PA4 and PA5 pins are available respectively on JP11 and JP10
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

This commit fixes regulator-sd_switch node in order to be compliant to
DT validation schema.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

"phy-names" entries are not used. To be compliant with DT validation
tool, those entries have to be remove.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

"#size-cells" entry is not needed for "gpio-keys" driver. Indeed "reg"
entry is not used. This commit will fix a warnings seen by DT validation
tool.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

DT validation ("make dtbs_check") has shown that some memory nodes were not
correctly written. This commit fixes this kind of issue:

"stm32f746-disco.dt.yaml: /: memory: False schema does not allow
{'device_type': ['memory'], 'reg': [[3221225472, 8388608]]}"
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Enable focaltech ft6236 touchscreen on STM32MP157C-DK2 board.
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Configure ADC support on stm32mp157a-dk1. It can be used for various
purpose:
- AIN connector has several analog inputs: ANA0, ANA1, ADC2 in6 & in2,
  ADC1 in13 & in6
- USB Type-C CC1 & CC2 pins wired to in18 & in19
It's easier then to Configure them all. But keep them disabled by default,
so the pins are kept in their initial state to lower power consumption.
This way they can also be used as GPIO.
Add VDD and VDDA supplies to ADC on stm32mp157c-dk1 board. This allows to
get full ADC analog performances in case VDDA is below 2.7V (not the case
by default).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>

Define pins that can be used for ADC on stm32mp157a-dk1 board:
- AIN connector has ADC input pins
- USB Type-C CC1 & CC2 pins (e.g. in18, in19)
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>