When booting the card, check for a dedicated regulatory ACPI entry. If
such exists, read it and give the information to FW with the appropriate
source.
Signed-off-by: Jonathan Doron <jonathanx.doron@intel.com>
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

For some configurations, the driver should get the MAC
address from the hardware registers and not from the
regular locations. Since the parsing of the MAC address
is the same regardless of its source, continue the regular
code path (parsing) after we read the registers.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This module parameter is useful for debugging NVM and LAR related issues.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Starting from family 8000 B0 step the radio_cfg parameters
and the get_sku parameters moved from SW section to PHY_SKU section.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

11ac depends on 11n, so disable it if 11n is disabled.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

If LAR is supported in TLV, but the NVM does not enable it, then disable
LAR support and ignore the TLV's bit that enabled LAR.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

max_eirp affects the txpower configured to the power,
so use the max tx power (22) instead of some other
value.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Fix the last 5ghz channel to 165 instead of 161
Add support for 8000 family, until channel 181.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Otherwise the regulatory data will mistakenly contain only 7000 series
channels.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Chub (Communication Hub, CommsHUB) is a HW component that connects to the cellular
and connectivity cores that gets updates of mcc changes, and then notifies the FW
directly of any mcc change.

The ucode notifies the driver (via this command) that it should ask for an mcc update,
and the driver sends the ucode the update mcc command to set the updated regulatory info.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Remove a useless debug print about unsupported channels.
Also add a comment about the LAR special case where channels
might become valid later.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

According to updated regulatory guidelines, the ACTIVE bit in the NVM
also allows ibss activity on the channel. The IBSS NVM bit is not updated
when LAR is active and is deprecated. Using this bit for NO-IR incorrectly
causes all 5Ghz channels to be marked as passive.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Register to cfg80211 with all channels enabled when LAR is supported.
Appropriate channels will later be disabled when a specific regulatory
domain is defined.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Parse the NVM channel data and create a regulatory domain with a rule
for every 20Mhz channel. Use the AUTO_BW flag so the regulatory core
can unify single-channel rules into ranges.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

During init queue a regulatory update to retrieve the default
regulatory settings from FW. If we're during recovery, only replay the
current country code to FW, if it exists.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The new API sets an MCC (mobile country code) to FW and receives a
channel structure to be used as a basis for an updated regulatory domain.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The commit below didn't update the max_ht_ampdu_exponent
for the devices listed in iwl-[1-6]000.c which, in result,
became 0 instead of 8K. This reduced the size of the Rx
AMPDU from 64K to 8K which had an impact in the Rx
throughput. One user reported that because of this, his
downstream throughput droppped by a half.

CC: <stable@vger.kernel.org> [3.19]
Fixes: c064ddf3 ("iwlwifi: change max HT and VHT A-MPDU exponent")
Reported-and-tested-by: Valentin Manea <linux-wireless@mrs.ro>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The commits below broke compilation when
CONFIG_IWLWIFI_DEBUGFS is not set.
FIx that.

Fixes: ddf89ab1 ("iwlwifi: mvm: allow to force the Rx chains from debugfs")
Fixes: 9d761fd8 ("iwlwifi: mvm: add trigger for firmware dump upon missed beacons")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Currently scan params structure has only active or passive dwell time
fields, passive one is used for fragmented scans too. FW needs the
passive dwell time even when performing fragmented scan for calculating
time between channels. Add a separate parameter for fragmented dwell time
and pass both fragmented and passive to FW.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Lots of issues can be caught when the RSSI drops. Add the
ability to collect the firmware data at that point.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

It can be very useful to monitor the statistics and trigger
a firmware dump when a certain value hits a certain offset.
Since the statistics are huge, add a generic trigger. When
the DWORD at offset X reaches value Y.

Since there is another trigger before this one I can't add
right now because of a dependency on mac80211, add a
reserved entry to keep the enum in place.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Sometimes the firmware will have a hard coded configuration.
In this case, the driver won't find any configuration
in the firmware file, and it will have to re-start
recording in case it has been stopped. This can't be done
by the configuration host command since there is no such
host command configured. Do that with the registers instead.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This will allow to collect the data as soon the firmware
sends a specific notification of command response.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

We fire the trigger when the channel switch starts, but
the delay is configurable. That makes is easier to catch
channel switches that fail.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Missing beacons is a good indication that something is going
wrong in the firmware. Add a trigger to be able to collect
data when we start missing beacons with a configurable
threshold.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Now that the firmware dump can be triggered by events in
the code and not only the user or an firmware ASSERT, we
need a way to know why the firmware dump was triggered.
Add a section in the dump file for that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Most of the time, the issues we want to debug with the
firmware dump mechanism are transient. It is then very
hard to stop the recording on time and get meaningful
data.
In order to solve this, I add here an infrastucture
of triggers. The user will supply a list of triggers
that will start / stop the recording. We have two types
of triggers: start and stop. Start triggers can start a
specific configuration. The stop triggers will be able to
kick the collection of the data with the currently running
configuration. These triggers are given to the driver by
the .ucode file - just like the configuration.

In the next patches, I'll add triggers in the code.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

20 ms fragments are no longer required by system.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This is useful to debug weird antenna problems.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Packet Level Co-Running is a BT Coex feature which is
supported on certain devices only, hence the need for
a TLV flag for it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

We shouldn't call iwl_mvm_d3_disconnect_iter() on the running
interfaces when we are woken up due to net-detect, because it doesn't
make sense.  Additionally, this seems to set the
IEEE80211_SDATA_DISCONNECT_RESUME flag that will cause a disconnection
on the next resume (if a normal WoWLAN is used).

To solve this, skip the iteration loop when net-detect is set.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reported-by: Samuel Tan <samueltan@chromium.org>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The new API slightly changes the layout of the version of
the firmware - prepare for that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Report the average beacon signal and the number of received beacons as
measured by the firmware.

Since the firmware just counts, and doesn't reset the counter at all,
clear it in the firmware whenever we associate. However, accumulate it
over firmware restart.

Since clearing the statistics in the firmware will also clear the ones
for the radio statistics, add those to the accumulator when cleared.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Due to HW bug in the DBGC when driver want to stop the dbg recording it
should wait 100us before collecting the data instead of write 0 to
DBGC_OUT_CTRL.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The legacy scan API is deprecated and not used anymore with 10 and
higher firmware versions.  Since we deprecated firmware version 9, we
can remove a whole lot of unused code.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This firmware is not supported anymore.  Stop loading this firmware.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Export the radio statistics from the statistics v10 API (if the
firmware also has the capability to fill these statistics) using
the global survey data facility.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

New firmware versions will report statistics using a new version 10
of the API, instead of the current version 8. Add support for this.
This enables getting beacon and radio statistics.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This allows to use the firmware debugging system even when
the configuration values are set hard coded in the firmware.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Cleanup unused code.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>