Pull vfs fixes from Al Viro:
 "No common topic, just assorted fixes"

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fuse: fix the ->direct_IO() treatment of iov_iter
  fs: fix cast in fsparam_u32hex() macro
  vboxsf: Fix the check for the old binary mount-arguments struct

Pull networking fixes from Jakub Kicinski:

 - fix failure to add bond interfaces to a bridge, the offload-handling
   code was too defensive there and recent refactoring unearthed that.
   Users complained (Ido)

 - fix unnecessarily reflecting ECN bits within TOS values / QoS marking
   in TCP ACK and reset packets (Wei)

 - fix a deadlock with bpf iterator. Hopefully we're in the clear on
   this front now... (Yonghong)

 - BPF fix for clobbering r2 in bpf_gen_ld_abs (Daniel)

 - fix AQL on mt76 devices with FW rate control and add a couple of AQL
   issues in mac80211 code (Felix)

 - fix authentication issue with mwifiex (Maximilian)

 - WiFi connectivity fix: revert IGTK support in ti/wlcore (Mauro)

 - fix exception handling for multipath routes via same device (David
   Ahern)

 - revert back to a BH spin lock flavor for nsid_lock: there are paths
   which do require the BH context protection (Taehee)

 - fix interrupt / queue / NAPI handling in the lantiq driver (Hauke)

 - fix ife module load deadlock (Cong)

 - make an adjustment to netlink reply message type for code added in
   this release (the sole change touching uAPI here) (Michal)

 - a number of fixes for small NXP and Microchip switches (Vladimir)

[ Pull request acked by David: "you can expect more of this in the
  future as I try to delegate more things to Jakub" ]

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (167 commits)
  net: mscc: ocelot: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
  net: dsa: seville: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
  net: dsa: felix: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
  inet_diag: validate INET_DIAG_REQ_PROTOCOL attribute
  net: bridge: br_vlan_get_pvid_rcu() should dereference the VLAN group under RCU
  net: Update MAINTAINERS for MediaTek switch driver
  net/mlx5e: mlx5e_fec_in_caps() returns a boolean
  net/mlx5e: kTLS, Avoid kzalloc(GFP_KERNEL) under spinlock
  net/mlx5e: kTLS, Fix leak on resync error flow
  net/mlx5e: kTLS, Add missing dma_unmap in RX resync
  net/mlx5e: kTLS, Fix napi sync and possible use-after-free
  net/mlx5e: TLS, Do not expose FPGA TLS counter if not supported
  net/mlx5e: Fix using wrong stats_grps in mlx5e_update_ndo_stats()
  net/mlx5e: Fix multicast counter not up-to-date in "ip -s"
  net/mlx5e: Fix endianness when calculating pedit mask first bit
  net/mlx5e: Enable adding peer miss rules only if merged eswitch is supported
  net/mlx5e: CT: Fix freeing ct_label mapping
  net/mlx5e: Fix memory leak of tunnel info when rule under multipath not ready
  net/mlx5e: Use synchronize_rcu to sync with NAPI
  net/mlx5e: Use RCU to protect rq->xdp_prog
  ...

Pull io_uring fixes from Jens Axboe:
 "A few fixes - most of them regression fixes from this cycle, but also
  a few stable heading fixes, and a build fix for the included demo tool
  since some systems now actually have gettid() available"

* tag 'io_uring-5.9-2020-09-22' of git://git.kernel.dk/linux-block:
  io_uring: fix openat/openat2 unified prep handling
  io_uring: mark statx/files_update/epoll_ctl as non-SQPOLL
  tools/io_uring: fix compile breakage
  io_uring: don't use retry based buffered reads for non-async bdev
  io_uring: don't re-setup vecs/iter in io_resumit_prep() is already there
  io_uring: don't run task work on an exiting task
  io_uring: drop 'ctx' ref on task work cancelation
  io_uring: grab any needed state during defer prep

Pull block fixes from Jens Axboe:
 "A few NVMe fixes, and a dasd write zero fix"

* tag 'block-5.9-2020-09-22' of git://git.kernel.dk/linux-block:
  nvmet: get transport reference for passthru ctrl
  nvme-core: get/put ctrl and transport module in nvme_dev_open/release()
  nvme-tcp: fix kconfig dependency warning when !CRYPTO
  nvme-pci: disable the write zeros command for Intel 600P/P3100
  s390/dasd: Fix zero write for FBA devices

Pull tracing fixes from Steven Rostedt:

 - Check kprobe is enabled before unregistering from ftrace as it isn't
   registered when disabled.

 - Remove kprobes enabled via command-line that is on init text when
   freed.

 - Add missing RCU synchronization for ftrace trampoline symbols removed
   from kallsyms.

 - Free trampoline on error path if ftrace_startup() fails.

 - Give more space for the longer PID numbers in trace output.

 - Fix a possible double free in the histogram code.

 - A couple of fixes that were discovered by sparse.

* tag 'trace-v5.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  bootconfig: init: make xbc_namebuf static
  kprobes: tracing/kprobes: Fix to kill kprobes on initmem after boot
  tracing: fix double free
  ftrace: Let ftrace_enable_sysctl take a kernel pointer buffer
  tracing: Make the space reserved for the pid wider
  ftrace: Fix missing synchronize_rcu() removing trampoline from kallsyms
  ftrace: Free the trampoline when ftrace_startup() fails
  kprobes: Fix to check probe enabled before disarm_kprobe_ftrace()

Vladimir Oltean says:

====================
Fix broken tc-flower rules for mscc_ocelot switches

All 3 switch drivers from the Ocelot family have the same bug in the
VCAP IS2 key offsets, which is that some keys are in the incorrect
order.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The IS2 IP4_TCP_UDP key offsets do not correspond to the VSC7514
datasheet. Whether they work or not is unknown to me. On VSC9959 and
VSC9953, with the same mistake and same discrepancy from the
documentation, tc-flower src_port and dst_port rules did not work, so I
am assuming the same is true here.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since these were copied from the Felix VCAP IS2 code, and only the
offsets were adjusted, the order of the bit fields is still wrong.
Fix it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some of the IS2 IP4_TCP_UDP keys are not correct, like L4_DPORT,
L4_SPORT and other L4 keys. This prevents offloaded tc-flower rules from
matching on src_port and dst_port for TCP and UDP packets.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

User space could send an invalid INET_DIAG_REQ_PROTOCOL attribute
as caught by syzbot.

BUG: KMSAN: uninit-value in inet_diag_lock_handler net/ipv4/inet_diag.c:55 [inline]
BUG: KMSAN: uninit-value in __inet_diag_dump+0x58c/0x720 net/ipv4/inet_diag.c:1147
CPU: 0 PID: 8505 Comm: syz-executor174 Not tainted 5.9.0-rc4-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x21c/0x280 lib/dump_stack.c:118
 kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:122
 __msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:219
 inet_diag_lock_handler net/ipv4/inet_diag.c:55 [inline]
 __inet_diag_dump+0x58c/0x720 net/ipv4/inet_diag.c:1147
 inet_diag_dump_compat+0x2a5/0x380 net/ipv4/inet_diag.c:1254
 netlink_dump+0xb73/0x1cb0 net/netlink/af_netlink.c:2246
 __netlink_dump_start+0xcf2/0xea0 net/netlink/af_netlink.c:2354
 netlink_dump_start include/linux/netlink.h:246 [inline]
 inet_diag_rcv_msg_compat+0x5da/0x6c0 net/ipv4/inet_diag.c:1288
 sock_diag_rcv_msg+0x24f/0x620 net/core/sock_diag.c:256
 netlink_rcv_skb+0x6d7/0x7e0 net/netlink/af_netlink.c:2470
 sock_diag_rcv+0x63/0x80 net/core/sock_diag.c:275
 netlink_unicast_kernel net/netlink/af_netlink.c:1304 [inline]
 netlink_unicast+0x11c8/0x1490 net/netlink/af_netlink.c:1330
 netlink_sendmsg+0x173a/0x1840 net/netlink/af_netlink.c:1919
 sock_sendmsg_nosec net/socket.c:651 [inline]
 sock_sendmsg net/socket.c:671 [inline]
 ____sys_sendmsg+0xc82/0x1240 net/socket.c:2353
 ___sys_sendmsg net/socket.c:2407 [inline]
 __sys_sendmsg+0x6d1/0x820 net/socket.c:2440
 __do_sys_sendmsg net/socket.c:2449 [inline]
 __se_sys_sendmsg+0x97/0xb0 net/socket.c:2447
 __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2447
 do_syscall_64+0x9f/0x140 arch/x86/entry/common.c:48
 entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x441389
Code: e8 fc ab 02 00 48 83 c4 18 c3 0f 1f 80 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 1b 09 fc ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007fff3b02ce98 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 0000000000441389
RDX: 0000000000000000 RSI: 0000000020001500 RDI: 0000000000000003
RBP: 00000000006cb018 R08: 00000000004002c8 R09: 00000000004002c8
R10: 0000000000000004 R11: 0000000000000246 R12: 0000000000402130
R13: 00000000004021c0 R14: 0000000000000000 R15: 0000000000000000

Uninit was created at:
 kmsan_save_stack_with_flags mm/kmsan/kmsan.c:143 [inline]
 kmsan_internal_poison_shadow+0x66/0xd0 mm/kmsan/kmsan.c:126
 kmsan_slab_alloc+0x8a/0xe0 mm/kmsan/kmsan_hooks.c:80
 slab_alloc_node mm/slub.c:2907 [inline]
 __kmalloc_node_track_caller+0x9aa/0x12f0 mm/slub.c:4511
 __kmalloc_reserve net/core/skbuff.c:142 [inline]
 __alloc_skb+0x35f/0xb30 net/core/skbuff.c:210
 alloc_skb include/linux/skbuff.h:1094 [inline]
 netlink_alloc_large_skb net/netlink/af_netlink.c:1176 [inline]
 netlink_sendmsg+0xdb9/0x1840 net/netlink/af_netlink.c:1894
 sock_sendmsg_nosec net/socket.c:651 [inline]
 sock_sendmsg net/socket.c:671 [inline]
 ____sys_sendmsg+0xc82/0x1240 net/socket.c:2353
 ___sys_sendmsg net/socket.c:2407 [inline]
 __sys_sendmsg+0x6d1/0x820 net/socket.c:2440
 __do_sys_sendmsg net/socket.c:2449 [inline]
 __se_sys_sendmsg+0x97/0xb0 net/socket.c:2447
 __x64_sys_sendmsg+0x4a/0x70 net/socket.c:2447
 do_syscall_64+0x9f/0x140 arch/x86/entry/common.c:48
 entry_SYSCALL_64_after_hwframe+0x44/0xa9

Fixes: 3f935c75 ("inet_diag: support for wider protocol numbers")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Christoph Paasch <cpaasch@apple.com>
Cc: Mat Martineau <mathew.j.martineau@linux.intel.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When calling the RCU brother of br_vlan_get_pvid(), lockdep warns:

=============================
WARNING: suspicious RCU usage
5.9.0-rc3-01631-g13c17acb8e38-dirty #814 Not tainted
-----------------------------
net/bridge/br_private.h:1054 suspicious rcu_dereference_protected() usage!

Call trace:
 lockdep_rcu_suspicious+0xd4/0xf8
 __br_vlan_get_pvid+0xc0/0x100
 br_vlan_get_pvid_rcu+0x78/0x108

The warning is because br_vlan_get_pvid_rcu() calls nbp_vlan_group()
which calls rtnl_dereference() instead of rcu_dereference(). In turn,
rtnl_dereference() calls rcu_dereference_protected() which assumes
operation under an RCU write-side critical section, which obviously is
not the case here. So, when the incorrect primitive is used to access
the RCU-protected VLAN group pointer, READ_ONCE() is not used, which may
cause various unexpected problems.

I'm sad to say that br_vlan_get_pvid() and br_vlan_get_pvid_rcu() cannot
share the same implementation. So fix the bug by splitting the 2
functions, and making br_vlan_get_pvid_rcu() retrieve the VLAN groups
under proper locking annotations.

Fixes: 7582f5b7 ("bridge: add br_vlan_get_pvid_rcu()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5 fixes-2020-09-18

This series introduces some fixes to mlx5 driver.

Please pull and let me know if there is any problem.

v1->v2:
 Remove missing patch from -stable list.

For -stable v5.1
 ('net/mlx5: Fix FTE cleanup')

For -stable v5.3
 ('net/mlx5e: TLS, Do not expose FPGA TLS counter if not supported')
 ('net/mlx5e: Enable adding peer miss rules only if merged eswitch is supported')

For -stable v5.7
 ('net/mlx5e: Fix memory leak of tunnel info when rule under multipath not ready')

For -stable v5.8
 ('net/mlx5e: Use RCU to protect rq->xdp_prog')
 ('net/mlx5e: Fix endianness when calculating pedit mask first bit')
 ('net/mlx5e: Use synchronize_rcu to sync with NAPI')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Update maintainers for MediaTek switch driver with Landen Chao who is
familiar with MediaTek MT753x switch devices and will help maintenance
from the vendor side.

Cc: Steven Liu <steven.liu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Landen Chao <Landen.Chao@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Returning errno is a bug, fix that.

Also fixes smatch warnings:
drivers/net/ethernet/mellanox/mlx5/core/en/port.c:453
mlx5e_fec_in_caps() warn: signedness bug returning '(-95)'

Fixes: 2132b71f ("net/mlx5e: Advertise globaly supported FEC modes")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Aya Levin <ayal@nvidia.com>

The spinlock only needed when accessing the channel's icosq, grab the lock
after the buf allocation in resync_post_get_progress_params() to avoid
kzalloc(GFP_KERNEL) in atomic context.

Fixes: 0419d8c9 ("net/mlx5e: kTLS, Add kTLS RX resync support")
Reported-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>

Resync progress params buffer and dma weren't released on error,
Add missing error unwinding for resync_post_get_progress_params().

Fixes: 0419d8c9 ("net/mlx5e: kTLS, Add kTLS RX resync support")
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>

Progress params dma address is never unmapped, unmap it when completion
handling is over.

Fixes: 0419d8c9 ("net/mlx5e: kTLS, Add kTLS RX resync support")
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>

Using synchronize_rcu() is sufficient to wait until running NAPI quits.

See similar upstream fix with detailed explanation:
("net/mlx5e: Use synchronize_rcu to sync with NAPI")

This change also fixes a possible use-after-free as the NAPI
might be already released at this stage.

Fixes: 0419d8c9 ("net/mlx5e: kTLS, Add kTLS RX resync support")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

The set of TLS TX global SW counters in mlx5e_tls_sw_stats_desc
is updated from all rings by using atomic ops.
This set of stats is used only in the FPGA TLS use case, not in
the Connect-X TLS one, where regular per-ring counters are used.

Do not expose them in the Connect-X use case, as this would cause
counter duplication. For example, tx_tls_drop_no_sync_data would
appear twice in the ethtool stats.

Fixes: d2ead1f3 ("net/mlx5e: Add kTLS TX HW offload support")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

The cited commit started to reuse function mlx5e_update_ndo_stats() for
the representors as well.
However, the function is hard-coded to work on mlx5e_nic_stats_grps only.
Due to this issue, the representors statistics were not updated in the
output of "ip -s".

Fix it to work with the correct group by extracting it from the caller's
profile.

Also, while at it and since this function became generic, move it to
en_stats.c and rename it accordingly.

Fixes: 8a236b15 ("net/mlx5e: Convert rep stats to mlx5e_stats_grp-based infra")
Signed-off-by: Alaa Hleihel <alaa@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Currently the FW does not generate events for counters other than error
counters. Unlike ".get_ethtool_stats", ".ndo_get_stats64" (which ip -s
uses) might run in atomic context, while the FW interface is non atomic.
Thus, 'ip' is not allowed to issue FW commands, so it will only display
cached counters in the driver.

Add a SW counter (mcast_packets) in the driver to count rx multicast
packets. The counter also counts broadcast packets, as we consider it a
special case of multicast.
Use the counter value when calling "ip -s"/"ifconfig".

Fixes: f62b8bb8 ("net/mlx5: Extend mlx5_core to support ConnectX-4 Ethernet functionality")
Signed-off-by: Ron Diskin <rondi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

The field mask value is provided in network byte order and has to
be converted to host byte order before calculating pedit mask
first bit.

Fixes: 88f30bbc ("net/mlx5e: Bit sized fields rewrite support")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

The cited commit creates peer miss group during switchdev mode
initialization in order to handle miss packets correctly while in VF
LAG mode. This is done regardless of FW support of such groups which
could cause rules setups failure later on.

Fix by adding FW capability check before creating peer groups/rule.

Fixes: ac004b83 ("net/mlx5e: E-Switch, Add peer miss rules")
Signed-off-by: Maor Dickman <maord@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Raed Salem <raeds@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Add missing mapping remove call when removing ct rule,
as the mapping was allocated when ct rule was adding with ct_label.
Also there is a missing mapping remove call in error flow.

Fixes: 54b154ec ("net/mlx5e: CT: Map 128 bits labels to 32 bit map ID")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

When deleting vxlan flow rule under multipath, tun_info in parse_attr is
not freed when the rule is not ready.

Fixes: ef06c9ee ("net/mlx5e: Allow one failure when offloading tc encap rules under multipath")
Signed-off-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

As described in the previous commit, napi_synchronize doesn't quite fit
the purpose when we just need to wait until the currently running NAPI
quits. Its implementation waits until NAPI is not running by polling and
waiting for 1ms in between. In cases where we need to deactivate one
queue (e.g., recovery flows) or where we deactivate them one-by-one
(deactivate channel flow), we may get stuck in napi_synchronize forever
if other queues keep NAPI active, causing a soft lockup. Depending on
kernel configuration (CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC), it may result
in a kernel panic.

To fix the issue, use synchronize_rcu to wait for NAPI to quit, and wrap
the whole NAPI in rcu_read_lock.

Fixes: acc6c595 ("net/mlx5e: Split open/close channels to stages")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Currently, the RQs are temporarily deactivated while hot-replacing the
XDP program, and napi_synchronize is used to make sure rq->xdp_prog is
not in use. However, napi_synchronize is not ideal: instead of waiting
till the end of a NAPI cycle, it polls and waits until NAPI is not
running, sleeping for 1ms between the periodic checks. Under heavy
workloads, this loop will never end, which may even lead to a kernel
panic if the kernel detects the hangup. Such workloads include XSK TX
and possibly also heavy RX (XSK or normal).

The fix is inspired by commit 326fe02d ("net/mlx4_en: protect
ring->xdp_prog with rcu_read_lock"). As mlx5e_xdp_handle is already
protected by rcu_read_lock, and bpf_prog_put uses call_rcu to free the
program, there is no need for additional synchronization if proper RCU
functions are used to access the pointer. This patch converts all
accesses to rq->xdp_prog to use RCU functions.

Fixes: 86994156 ("net/mlx5e: XDP fast RX drop bpf programs support")
Fixes: db05815b ("net/mlx5e: Add XSK zero-copy support")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>

Currently, when an FTE is allocated, its refcount is decreased to 0
with the purpose it will not be a stand alone steering object and every
rule (destination) of the FTE would increase the refcount.
When mlx5_cleanup_fs is called while not all rules were deleted by the
steering users, it hit refcount underflow on the FTE once clean_tree
calls to tree_remove_node after the deleted rules already decreased
the refcount to 0.

FTE is no longer destroyed implicitly when the last rule (destination)
is deleted. mlx5_del_flow_rules avoids it by increasing the refcount on
the FTE and destroy it explicitly after all rules were deleted. So we
can avoid the refcount underflow by making FTE as stand alone object.
In addition need to set del_hw_func to FTE so the HW object will be
destroyed when the FTE is deleted from the cleanup_tree flow.

refcount_t: underflow; use-after-free.
WARNING: CPU: 2 PID: 15715 at lib/refcount.c:28 refcount_warn_saturate+0xd9/0xe0
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
Call Trace:
 tree_put_node+0xf2/0x140 [mlx5_core]
 clean_tree+0x4e/0xf0 [mlx5_core]
 clean_tree+0x4e/0xf0 [mlx5_core]
 clean_tree+0x4e/0xf0 [mlx5_core]
 clean_tree+0x5f/0xf0 [mlx5_core]
 clean_tree+0x4e/0xf0 [mlx5_core]
 clean_tree+0x5f/0xf0 [mlx5_core]
 mlx5_cleanup_fs+0x26/0x270 [mlx5_core]
 mlx5_unload+0x2e/0xa0 [mlx5_core]
 mlx5_unload_one+0x51/0x120 [mlx5_core]
 mlx5_devlink_reload_down+0x51/0x90 [mlx5_core]
 devlink_reload+0x39/0x120
 ? devlink_nl_cmd_reload+0x43/0x220
 genl_rcv_msg+0x1e4/0x420
 ? genl_family_rcv_msg_attrs_parse+0x100/0x100
 netlink_rcv_skb+0x47/0x110
 genl_rcv+0x24/0x40
 netlink_unicast+0x217/0x2f0
 netlink_sendmsg+0x30f/0x430
 sock_sendmsg+0x30/0x40
 __sys_sendto+0x10e/0x140
 ? handle_mm_fault+0xc4/0x1f0
 ? do_page_fault+0x33f/0x630
 __x64_sys_sendto+0x24/0x30
 do_syscall_64+0x48/0x130
 entry_SYSCALL_64_after_hwframe+0x44/0xa9

Fixes: 718ce4d6 ("net/mlx5: Consolidate update FTE for all removal changes")
Fixes: bd71b08e ("net/mlx5: Support multiple updates of steering rules in parallel")
Signed-off-by: Maor Gottlieb <maorg@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Merge tag 'mac80211-for-net-2020-09-21' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
Just a few fixes:
 * fix using HE on 2.4 GHz
 * AQL (airtime queue limit) estimation & VHT160 fix
 * do not oversize A-MPDUs if local capability is smaller than peer's
 * fix radiotap on 6 GHz to not put 2.4 GHz flag
 * fix Kconfig for lib80211
 * little fixlet for 6 GHz channel number / frequency conversion
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace a comma between expression statements by a semicolon.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

This failure path should return a negative error code but it currently
returns success.

Fixes: 51b35a45 ("sfc: skeleton EF100 PF driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull RCU fix from Paul McKenney:
 "This contains a single commit that fixes a bug that was introduced in
  the last merge window. This bug causes a compiler warning complaining
  about show_rcu_tasks_classic_gp_kthread() being an unused static
  function in !SMP kernels.

  The fix is straightforward, just adding an 'inline' to make this a
  static inline function, thus avoiding the warning.

  This bug was reported by Laurent Pinchart, who would like it fixed
  sooner rather than later"

* 'rcu/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu:
  rcu-tasks: Prevent complaints of unused show_rcu_tasks_classic_gp_kthread()

Pull kvm fixes from Paolo Bonzini:
 "ARM:
   - fix fault on page table writes during instruction fetch

  s390:
   - doc improvement

  x86:
   - The obvious patches are always the ones that turn out to be
     completely broken. /me hangs his head in shame"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  Revert "KVM: Check the allocation of pv cpu mask"
  KVM: arm64: Remove S1PTW check from kvm_vcpu_dabt_iswrite()
  KVM: arm64: Assume write fault on S1PTW permission fault on instruction fetch
  docs: kvm: add documentation for KVM_CAP_S390_DIAG318

Pull libnvdimm fix from Dan Williams:
 "Fix compilation for the new dax_supported() exported helper"

* tag 'libnvdimm-fixes-5.9-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  dax: Fix compilation for CONFIG_DAX && !CONFIG_FS_DAX

dax_supported() is defined whenever CONFIG_DAX is enabled. So dummy
implementation should be defined only in !CONFIG_DAX case, not in
!CONFIG_FS_DAX case.

Fixes: e2ec5128 ("dm: Call proper helper to determine dax support")
Cc: <stable@vger.kernel.org>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>

A previous commit unified how we handle prep for these two functions,
but this means that we check the allowed context (SQPOLL, specifically)
later than we should. Move the ring type checking into the two parent
functions, instead of doing it after we've done some setup work.

Fixes: ec65fea5 ("io_uring: deduplicate io_openat{,2}_prep()")
Reported-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

These will naturally fail when attempted through SQPOLL, but either
with -EFAULT or -EBADF. Make it explicit that these are not workable
through SQPOLL and return -EINVAL, just like other ops that need to
use ->files.
Signed-off-by: Jens Axboe <axboe@kernel.dk>

It would seem none of the kernel continuous integration does this:
    $ cd tools/io_uring
    $ make

Otherwise it may have noticed:
   cc -Wall -Wextra -g -D_GNU_SOURCE   -c -o io_uring-bench.o
	 io_uring-bench.c
io_uring-bench.c:133:12: error: static declaration of ‘gettid’
	 follows non-static declaration
  133 | static int gettid(void)
      |            ^~~~~~
In file included from /usr/include/unistd.h:1170,
                 from io_uring-bench.c:27:
/usr/include/x86_64-linux-gnu/bits/unistd_ext.h:34:16: note:
	 previous declaration of ‘gettid’ was here
   34 | extern __pid_t gettid (void) __THROW;
      |                ^~~~~~
make: *** [<builtin>: io_uring-bench.o] Error 1

The problem on Ubuntu 20.04 (with lk 5.9.0-rc5) is that unistd.h
already defines gettid(). So prefix the local definition with
"lk_".
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

Some block devices, like dm, bubble back -EAGAIN through the completion
handler. We check for this in io_read(), but don't honor it for when
we have copied the iov. Return -EAGAIN for this case before retrying,
to force punt to io-wq.

Fixes: bcf5a063 ("io_uring: support true async buffered reads, if file provides it")
Reported-by: Zorro Lang <zlang@redhat.com>
Tested-by: Zorro Lang <zlang@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>

If we already have mapped the necessary data for retry, then don't set
it up again. It's a pointless operation, and we leak the iovec if it's
a large (non-stack) vec.

Fixes: b63534c4 ("io_uring: re-issue block requests that failed because of resources")
Signed-off-by: Jens Axboe <axboe@kernel.dk>