This clause is conditioned on htc_hdr != NULL, but it will only be NULL
when that check is reached.

Coverity: CID 114318
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This patch introduces the use of function put_unaligned_le32.

This is done using Coccinelle and semantic patch used is as follows:

@A@
typedef u32, __le32, uint32_t;
{u32,__le32,uint32_t} e32;
identifier tmp;
expression ptr;
expression y,e;
type T;
type T;
@@

- tmp = cpu_to_le32(y);

<+... when != tmp
(
- memcpy(ptr, (T)&tmp, \(4\|sizeof(u32)\|sizeof(__le32)\|sizeof(uint32_t)\|sizeof(e32)\));
+ put_unaligned_le32(y,ptr);
|
- memcpy(ptr, (T)&tmp, ...);
+ put_unaligned_le32(y,ptr);
)
...+>
? tmp = e

@@ type T; identifier a.tmp; @@

- T tmp;
...when != tmp
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This moves main bus init code to the main.c and renames old function to
make its purpose clear.
Thanks to this change we'll also be able to separate scanning from
registration (and support PCIe Gen 2 devices) in the future.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Call b43_leds_stop during suspend to avoid this WARN:

WARNING: CPU: 1 PID: 0 at net/mac80211/util.c:755 ieee80211_can_queue_work.isra.11+0x35/0x50 [mac80211]()
queueing ieee80211 work while going to suspend

 [...]

Call Trace:
 [<c165fb2a>] dump_stack+0x48/0x69
 [<c1052f7b>] warn_slowpath_common+0x8b/0xc0
 [<f9c30225>] ? ieee80211_can_queue_work.isra.11+0x35/0x50 [mac80211]
 [<f9c30225>] ? ieee80211_can_queue_work.isra.11+0x35/0x50 [mac80211]
 [<c1052fe3>] warn_slowpath_fmt+0x33/0x40
 [<f9c30225>] ieee80211_can_queue_work.isra.11+0x35/0x50 [mac80211]
 [<f9c30260>] ieee80211_queue_work+0x20/0x40 [mac80211]
 [<f9f25d78>] b43_led_brightness_set+0x28/0x30 [b43]
 [<c14f3835>] led_timer_function+0xd5/0xe0
 [<c10cb534>] call_timer_fn+0xa4/0x4a0
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

We recently introduced a new error path which needs an unlock.

Fixes: 6d5a748d ('wlcore: add ability to reduce FW interrupts during suspend')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The else if check condition checks for the opposite of the
if check, hence the else if check is redundant and can be
replaced with a simple else:

if (rtlpriv->rtlhal.macphymode == SINGLEMAC_SINGLEPHY) {
	..
} else if (rtlpriv->rtlhal.macphymode != SINGLEMAC_SINGLEPHY) {
	..
}

replaced with:

if (rtlpriv->rtlhal.macphymode == SINGLEMAC_SINGLEPHY) {
	..
} else {
	..
}
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Add an option "blink" to enable or disable the LED blink. The default
value is set to 1 so that existing users would not experience any
unexpected changes.
Signed-off-by: Hong Xu <hong@topbug.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Currently, wcn36xx only asks for a TX BA session if it has
already established one for RX.  Thus, two wcn36xx devices cannot
do a-mpdu between themselves since they both wait for the other
to go first.  Fix this by starting a BA session after a few QoS
data frames have been sent to a STA.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The pdu is part of the buffer descriptor, so it makes
sense that one function would fill both.  Also, passing
the whole skb instead of just the header pointer to the
set_tx_data function paves the way for using its fields
for ampdu setup inside set_tx_data().
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The dxe lock is missing its initialization, so add it.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ctl->skb_lock is never initialized, a fact caught by lockdep.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The DMA engine will reset the valid bit after a descriptor is
complete; any with the valid bit still set may still be in
use by the hardware, so check that before freeing the descriptor.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

wcn36xx currently sends an incorrect sequence number into the BA session
setup firmware command: it should be saving or updating the ssn in the
TX_START ampdu_action callback instead of waiting until TX_OPERATIONAL.
However, we can sidestep the issue by letting the hardware generate the
sequence numbers for QoS frames, as is done in prima, so do that.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

bd->tx_comp is a single bit in a bitfield, so assigning
"info->flags & IEEE80211_TX_CTL_REQ_TX_STATUS" only happens
to work because TX_STATUS is defined to BIT(0); if it were
any other bit this assignment would fail.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Set up default configuration for the device when we call start.
The defaults come from dumps from the prima driver for the same
hardware.

This fixes transmit A-MPDU; previously only one MPDU would be
sent per A-MPDU due to missing MAX_MPDUS_IN_AMPDU setting.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Signed-off-by: Giel van Schijndel <me@mortis.eu>
Reported-at: http://www.viva64.com/en/b/0299/Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Avoid printing dev_{warn/dbg} messages while holding spinlock.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Ignore scan and connection requests from cfg80211 when driver
unload is in process or previous command has timed out due to
a firmware bug. This patch fixes corner case system crash
issues.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Check if the frame has been completed without any
error and use IEEE80211_TX_STAT_NOACK_TRANSMITTED to
indicate successful transmission of no-ack frames.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Merge tag 'iwlwifi-next-for-kalle-2015-01-22' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next

* more work for new devices (4165 / 8260)
* cleanups / improvemnts in rate control
* fixes for TDLS
* major statistics work from Johannes - more to come
* improvements for the fw error dump infrastructure
* usual amount of small fixes here and there (scan, D0i3 etc...)

In the PHY_CTXT command sent to the FW the TX chains were
indeed configured by the values of both FW TLVs and of NVM,
but the RX chains were left out and configured only by FW
TLV.

This causes problems in 4165 HW, where there are 1x1
antennas, and the wrong configuration denies the driver
from connecting to the AP.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The driver loads the 2 CPU sections, then it needs to let
the firmware know to start the authentication of the
sections. This is done by writing the relevants bits to
FH_UCODE_LOAD_STATUS.

For CPU1, the driver sets the lower 16 bits. For both CPUs,
the driver sets all the 32 bits.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The stats argument is always only passed as &mvm->drv_rx_stats, so
there's no point in passing it when the mvm pointer is passed.
Remove the argument entirely.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The new API tells the FW that it's allowed to use STBC
but the FW will decide on its own whether to use STBC
or SISO (and in the future Beamformer).
Keep support for the old API which sets STBC explicitly
in the rates in the LQ table while we still support old
FW revisions.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Prepare to add some more code there so refactor to
separate functions.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

for_each_set_bit expect the size in number of bits and not
in bytes.

Fixes: a0f6bf2a ("iwlwifi: mvm: use private TFD queues for TDLS stations")
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The iwl_mvm_mac_get_queues_mask() added vif->hw_queue[ac] to the
queue mask although it might be set to IEEE80211_INVAL_HW_QUEUE.
Fix it.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

With this value, we de-facto disable the feature. Since it
is not working yet, disable it completely.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

C step functionality in the driver is exactly the same as
B step besides the ucode name that present as iwlwifi-8000C-xx.ucode
instead of iwlwifi-8000B-xx.ucode
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The ref_lock that was recently added is missing initialization
which makes lockdep unhappy and is generally a bad idea.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Add a comment indicating that the WLAN_CIPHER_SUITE_WEP104 case falls
through to the WLAN_CIPHER_SUITE_WEP40 case in iwl_mvm_send_sta_key.
This will document that the lack of a break is intentional.

Coverity: CID 1260023
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Tx STBC was used only when in CAM mode or if powersave is disabled.
Effectively this meant we never used STBC as these modes aren't
used on most platforms by default. Change that.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This is now implemented by mac80211 (commit below).
mac80211 will flush/drop the frames on the queues before
suspending / disconnecting.
It will then send the deauth and wait until the queues are
empty.

commit 3b24f4c6
Author: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Date:   Wed Jan 7 15:42:39 2015 +0200

    mac80211: let flush() drop packets when possible

This reverts commit 4e6c48e0.

This new command will give finer granularity to configure
the platform.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This allow to better preserve the BT performance while
WiFi is running.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Conflicts:
	drivers/net/wireless/iwlwifi/iwl-fw-file.h
	drivers/net/wireless/iwlwifi/mvm/scan.c

In order to change the usage of U-APSD on the fly later,
move the enabling condition into a new function that is
called when authenticated.

This allows the module parameter to become writable, it
won't take effect immediately but at least on the next
association the new value will be used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Some further updates for net-next:
 * fix network-manager which was broken by the previous changes
 * fix delete-station events, which were broken by me making the
   genlmsg_end() mistake
 * fix a timer left running during suspend in some race conditions
   that would cause an annoying (but harmless) warning
 * (less important, but in the tree already) remove 80+80 MHz rate
   reporting since the spec doesn't distinguish it from 160 MHz;
   as the bitrate they're both 160 MHz bandwidth

If the firmware sends spontaneous DTS notfications with the
temperature (indicated in a TLV), we can ignore the temperature we get
in the RX statistics notifications.  This prevents potentially
handling the same temperature change twice.  It also ignores
notifications with temperature equal to 0 that happens from time to
time.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

These aren't useful and overflowing so drop them
and also fix a minor typo.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>