Taking PHY lock is not required on some older designs, but we are removing this
complication and always taking it since it is always required on newer designs
and does not worth the code complication on the older boards.

Taking PHY lock was initially required only on specific boards which had their
MDC/MDIO bus crossed, but since this lock is now always required, for example,
when NCSI is present, the PHY lock will always be taken.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for the 10G-baseT PHY - BCM84834, which is the quad-port version of
the dual-port BCM84833.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Per measurements, the SFP+ suffered from small current leakage in two cases:
 - When no module was plugged and TX laser was disabled. The fix was to enable
   it, and when module is plugged in, check if it needs to be disabled.
 - When over-current event occurs due to invalid SFP+ module, the HW basically
   shuts down the current for this module, but the SW needs to complete this
   by issuing a power down via a GPIO.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When drivers works on top of an old bootcode, it is theoretically subjected to
MDC/MDIO failures since the MDIO clock is set in the beginning of each sequence,
rather than per CL45 command. On rare cases an old bootcodes may change that in
the middle, so to address that, the MDIO clock is set for each CL45 access.
In addition, setting the MDIO clock is now done per EMAC base, and
not per port number, since a specific port can potentially use both EMACs for
different PHY accesses.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case Link Flap Avoidance feature is supported by the MCP, bnx2x will enable
it, and will pass the appropriate parameter when load request is sent to
the MCP.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Verify the length of the user-space arguments.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Instead of having the getsockopt() of SO_BINDTODEVICE return an index, which
will then require another call like if_indextoname() to get the actual interface
name, have it return the name directly.

This also matches the existing man page description on socket(7) which mentions
the argument being an interface name.

If the value has not been set, zero is returned and optlen will be set to zero
to indicate there is no interface name present.

Added a seqlock to protect this code path, and dev_ifname(), from someone
changing the device name via dev_change_name().

v2: Added seqlock protection while copying device name.

v3: Fixed word wrap in patch.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Common Platform Time Sync function of the CPSW does not depend the
CPSW configuration option as it should. This patch fixes the issue by
adding the dependency.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes the large buffer from the stack of the system
offset ioctl and replaces it with a kmalloced buffer.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes the large buffer from the stack of the read file
operation and replaces it with a kmalloced buffer.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Many new feauture have been introduced in the driver:
ethtool coalesce options, Rx HW watchdog... so this patch updates the
driver's version.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch updates the stmmac.txt adding some information
about the new rx/tx mitigation schema adopted in the driver.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch is to get/set the tx/rx coalesce parameters
via ethtool interface.

Tests have been done on several platform with different GMAC chips w/o and w/
RX watchdog feature.

V2: reject coalesce settings that are not supported.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

GMAC devices newer than databook 3.40 has an embedded timer
that can be used for mitigating the number of interrupts.
So this patch adds this optimizations.

At any rate, the Rx watchdog can be disable (on bugged HW) by
passing from the platform the riwt_off field.

In this implementation the rx timer stored in the Reg9 is fixed
to the max value. This will be tuned by using ethtool.

V2: added a platform parameter to force to disable the rx-watchdog
for example on new core where it is bugged.

V3: do not disable NAPI when Rx watchdog is used.

V4: a new extra statistic field has been added to show the early
receive status in the interrupt handler.
This patch also adds an extra check to avoid to call
napi_schedule when the DMA_INTR_ENA_RIE bit is disabled in the
Interrupt Mask register.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a new schema used for mitigating the
number of transmit interrupts.
It is based on a SW timer and a threshold value.
The timer is used to periodically call the stmmac_tx_clean
function; the threshold is used for setting the IC (Interrupt
on Completion bit). The ISR will then invoke the poll method.
Also the patch improves some ethtool stat fields.

V2: review the logic to manage the IC bit in the TDESC
that was bugged because it didn't take care about the
fragments. Also fix the tx_count_frames that has not to be
limited to TX DMA ring. Thanks to Ben Hutchings.

V3: removed the spin_lock irqsave/restore as D. Miller suggested.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The TIMER option is not longer supported and this
code can be considered dead for this driver in
the new kernel series.
In fact, It was not updated at all and never used.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch puts the correct method name, tun_do_read, in a debug message.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes four typos in drivers/net/vtun.c.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There's really no excuse for an additional wmem_default of buffering
between the netdev queue and the ATM device. Two packets (one in-flight,
and one ready to send) ought to be fine. It's not as if it should take
long to get another from the netdev queue when we need it.

If necessary we can make the queue space configurable later, but I don't
think it's likely to be necessary.

cf. commit 9d02daf7 (pppoatm: Fix
excessive queue bloat) which did something very similar for PPPoATM.

Note that there is a tremendously unlikely race condition which may
result in qspace temporarily going negative. If a CPU running the
br2684_pop() function goes off into the weeds for a long period of time
after incrementing qspace to 1, but before calling netdev_wake_queue()...
and another CPU ends up calling br2684_start_xmit() and *stopping* the
queue again before the first CPU comes back, the netdev queue could
end up being woken when qspace has already reached zero.

An alternative approach to coping with this race would be to check in
br2684_start_xmit() for qspace==0 and return NETDEV_TX_BUSY, but just
using '> 0' and '< 1' for comparison instead of '== 0' and '!= 0' is
simpler. It just warranted a mention of *why* we do it that way...

Move the call to atmvcc->send() to happen *after* the accounting and
potentially stopping the netdev queue, in br2684_xmit_vcc(). This matters
if the ->send() call suffers an immediate failure, because it'll call
br2684_pop() with the offending skb before returning. We want that to
happen *after* we've done the initial accounting for the packet in
question. Also make it return an appropriate success/failure indication
while we're at it.

Tested by running 'ping -l 1000 bottomless.aaisp.net.uk' from within my
network, with only a single PPPoE-over-BR2684 link running. And after
setting txqueuelen on the nas0 interface to something low (5, in fact).
Before the patch, we'd see about 15 packets being queued and a resulting
latency of ~56ms being reached. After the patch, we see only about 8,
which is fairly much what we expect. And a max latency of ~36ms. On this
OpenWRT box, wmem_default is 163840.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Reviewed-by: Krzysztof Mazur <krzysiek@podlesie.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 82167cb8 ('net: dsa/slave: Fix
compilation warnings') fixed one possible invalid configuration
(NET_DSA enabled with no trailer formats) but added others: drivers
can select NET_DSA without its dependencies being met.

It's not very useful to make either the DSA core or the tagging
formats manually selectable without a driver to use them, so:

1. Define a hidden HAVE_NET_DSA option and move the dependencies of
   NET_DSA to that.  While we're at it, drop the deprecated
   EXPERIMENTAL dependency.
2. Make NET_DSA and the drivers dependent on HAVE_NET_DSA.
3. Hide the tagging format options again.
4. Make drivers select both NET_DSA and the appropriate tagging format
   option.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Save a few bytes per table by convert mroute_do_assert and
mroute_do_pim from int to bool.

Remove !! as the compiler does that when assigning int to bool.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1) ip_mroute_setsockopt() & ip_mroute_getsockopt() should not
   access/set raw_sk(sk)->ipmr_table before making sure the socket
   is a raw socket, and protocol is IGMP

2) MRT_INIT should return -EINVAL if optlen != sizeof(int), not
   -ENOPROTOOPT

3) MRT_ASSERT & MRT_PIM should validate optlen

4) " (v) ? 1 : 0 " can be written as " !!v "
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the netdev patchwork entries for networking drivers.
Change the W: entry to Q:for networking.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Avoid any possible message logging interleaving by adding
missing newlines.

Align arguments.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently when none of CONFIG_NET_DSA_TAG_DSA, CONFIG_NET_DSA_TAG_EDSA and
CONFIG_NET_DSA_TAG_TRAILER is defined, we get following compilation warnings:

net/dsa/slave.c:51:12: warning: 'dsa_slave_init' defined but not used [-Wunused-function]
net/dsa/slave.c:60:12: warning: 'dsa_slave_open' defined but not used [-Wunused-function]
net/dsa/slave.c:98:12: warning: 'dsa_slave_close' defined but not used [-Wunused-function]
net/dsa/slave.c:116:13: warning: 'dsa_slave_change_rx_flags' defined but not used [-Wunused-function]
net/dsa/slave.c:127:13: warning: 'dsa_slave_set_rx_mode' defined but not used [-Wunused-function]
net/dsa/slave.c:136:12: warning: 'dsa_slave_set_mac_address' defined but not used [-Wunused-function]
net/dsa/slave.c:164:12: warning: 'dsa_slave_ioctl' defined but not used [-Wunused-function]

Earlier approach to fix this was discussed here:

lkml.org/lkml/2012/10/29/549

This is another approach to fix it. This is done by some changes in config
options, which make more sense than the earlier approach. As, atleast one
tagging option must always be selected for using net/dsa/ infrastructure, this
patch selects NET_DSA from tagging configs instead of having it as an selectable
config.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch makes it possible to build the CAN Identifier into the kernel, even
if the CAN support is build as a module.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Recovery doesn't work too well if we leave interrupts disabled...
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds support for byte queue limits on RTL8139C+

Tested on real hardware.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-By: Dave Täht <dave.taht@bufferbloat.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This fixes (for me) a regression introduced by commit b01af457 ("8139cp:
set ring address before enabling receiver"). That commit configured the
descriptor ring addresses earlier in the initialisation sequence, in
order to avoid the possibility of triggering stray DMA before the
correct address had been set up.

Unfortunately, it seems that the hardware will scribble garbage into the
TxRingAddr registers when we enable "plus mode" Tx in the CpCmd
register. Observed on a Traverse Geos router board.

To deal with this, while not reintroducing the problem which led to the
original commit, we augment cp_start_hw() to write to the CpCmd register
*first*, then set the descriptor ring addresses, and then finally to
enable Rx and Tx in the original 8139 Cmd register. The datasheet
actually indicates that we should enable Tx/Rx in the Cmd register
*before* configuring the descriptor addresses, but that would appear to
re-introduce the problem that the offending commit b01af457 was trying
to solve. And this variant appears to work fine on real hardware.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@kernel.org [3.5+]
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit b26623da.

This reverts the revert, in net-next we'll try another scheme
to fix this bug using patches from David Woodhouse.
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/wireless/iwlwifi/pcie/tx.c

Minor iwlwifi conflict in TX queue disabling between 'net', which
removed a bogus warning, and 'net-next' which added some status
register poking code.
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull sound build error fix from Takashi Iwai:
 "Only a single commit for fixing the build error without CONFIG_PM in
  hda driver."

* tag 'sound-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda - Fix build without CONFIG_PM

I forgot this again...  codec->in_pm is in #ifdef CONFIG_PM
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Pull x86 arch fixes from Peter Anvin:
 "Here is a collection of fixes for 3.7-rc7.  This is a superset of
  tglx' earlier pull request."

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86-64: Fix ordering of CFI directives and recent ASM_CLAC additions
  x86, microcode, AMD: Add support for family 16h processors
  x86-32: Export kernel_stack_pointer() for modules
  x86-32: Fix invalid stack address while in softirq
  x86, efi: Fix processor-specific memcpy() build error
  x86: remove dummy long from EFI stub
  x86, mm: Correct vmflag test for checking VM_HUGETLB
  x86, amd: Disable way access filter on Piledriver CPUs
  x86/mce: Do not change worker's running cpu in cmci_rediscover().
  x86/ce4100: Fix PCI configuration register access for devices without interrupts
  x86/ce4100: Fix reboot by forcing the reboot method to be KBD
  x86/ce4100: Fix pm_poweroff
  MAINTAINERS: Update email address for Robert Richter
  x86, microcode_amd: Change email addresses, MAINTAINERS entry
  MAINTAINERS: Change Boris' email address
  EDAC: Change Boris' email address
  x86, AMD: Change Boris' email address

Pull MTD fixes from David Woodhouse:
 "The most important part of this is that it fixes a regression in
  Samsung NAND chip detection, introduced by some rework which went into
  3.7.  The initial fix wasn't quite complete, so it's in two parts.  In
  fact the first part is committed twice (Artem committed his own copy
  of the same patch) and I've merged Artem's tree into mine which
  already had that fix.

  I'd have recommitted that to make it somewhat cleaner, but figured by
  this point in the release cycle it was better to merge *exactly* the
  commits which have been in linux-next.

  If I'd recommitted, I'd also omit the sparse warning fix.  But it's
  there, and it's harmless — just marking one function as 'static' in
  onenand code.

  This also includes a couple more fixes for stable: an AB-BA deadlock
  in JFFS2, and an invalid range check in slram."

* tag 'for-linus-20121123' of git://git.infradead.org/mtd-2.6:
  mtd: nand: fix Samsung SLC detection regression
  mtd: nand: fix Samsung SLC NAND identification regression
  jffs2: Fix lock acquisition order bug in jffs2_write_begin
  mtd: onenand: Make flexonenand_set_boundary static
  mtd: slram: invalid checking of absolute end address
  mtd: ofpart: Fix incorrect NULL check in parse_ofoldpart_partitions()
  mtd: nand: fix Samsung SLC NAND identification regression

Pull device tree regression fix from Grant Likely:
 "Simple build regression fix for DT device drivers on Sparc.  An
  earlier change had masked out the of_iomap() helper on SPARC."

* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux-2.6:
  of/address: sparc: Declare of_iomap as an extern function for sparc again

Pull power management update from Rafael Wysocki:
 "Fix for an incorrect error condition check in device PM QoS code that
  may lead to an Oops from Guennadi Liakhovetski."

* tag 'pm-for-3.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  PM / QoS: fix wrong error-checking condition

Pull md fixes from NeilBrown:
 "Several bug fixes for md in 3.7:

   - raid5 discard has problems
   - raid10 replacement devices have problems
   - bad block lock seqlock usage has problems
   - dm-raid doesn't free everything"

* tag 'md-3.7-fixes' of git://neil.brown.name/md:
  md/raid10: decrement correct pending counter when writing to replacement.
  md/raid10: close race that lose writes lost when replacement completes.
  md/raid5: Make sure we clear R5_Discard when discard is finished.
  md/raid5: move resolving of reconstruct_state earlier in stripe_handle.
  md/raid5: round discard alignment up to power of 2.
  md: make sure everything is freed when dm-raid stops an array.
  md: Avoid write invalid address if read_seqretry returned true.
  md: Reassigned the parameters if read_seqretry returned true in func md_is_badblock.