- 20 May, 2011 40 commits
-
-
Simon Farnsworth authored
To simplify maintainer support of this driver, bump the version to 1.5.0 - this will be the first version that is expected to support mmap() for raw video frames. Signed-off-by:
Simon Farnsworth <simon.farnsworth@onelan.co.uk> Acked-by:
Andy Walls <awalls@md.metrocast.net> Signed-off-by:
Mauro Carvalho Chehab <mchehab@redhat.com>
-
Simon Farnsworth authored
The initial version of this patch (commit d5976931639176bb6777755d96b9f8d959f79e9e) had some issues: * It didn't correctly calculate the size of the YUV buffer for 4:2:2, resulting in capture sometimes being offset by 1/3rd of a picture. * There were a lot of variables duplicating information the driver already knew, which have been removed. * There was an in-kernel format conversion - libv4l can do this one, and is the right place to do format conversions anyway. * Some magic numbers weren't properly explained. Fix all these issues, leaving just the move from videobuf to videobuf2 to do. Signed-off-by:
-
Mariusz Kozlowski authored
Currently 'fh' initialises to whatever happens to be on stack. This looks like a typo and this patch fixes that. Signed-off-by:
Mariusz Kozlowski <mk@lab.zgora.pl> Acked-by:
Hans Verkuil <hverkuil@xs4all.nl> Signed-off-by:
-
Antti Palosaari authored
Remove old DVB-T2 freq module param and detect DVB-T/T2 automatically. Implementation is trial and error, if DVB-T does not lock try DVB-T2 and vice versa. That's done by replacing normal DVBFE_ALGO_SW with DVBFE_ALGO_CUSTOM which gives better control for tuning process. DVB-C still uses normal software ZigZag, DVBFE_ALGO_SW. Signed-off-by:
Antti Palosaari <crope@iki.fi> Signed-off-by:
-
Antti Palosaari authored
Make checkpatch.pl happy by fixing whitespaces introduced by commit 79e8b8e3b8cbf67130247a3f6d25732373fe2f34 Signed-off-by:
-
Steve Kerrison authored
Signed-off-by:
Steve Kerrison <steve@stevekerrison.com> Signed-off-by:
-
Steve Kerrison authored
Signed-off-by:
-
Antti Palosaari authored
Supports DVB-T/T2/C, USB ID: 2013:024f. Empia EM28174, Sony CXD2820R and NXP TDA18271HD/C2. Signed-off-by:
-
Antti Palosaari authored
It is very first DVB-T2 Linux driver! Signed-off-by:
-
Antti Palosaari authored
EM28174 is very similar as already supported EM2874. I am not sure what are differences, but it could be analog support. Signed-off-by:
-
Antti Palosaari authored
Register multiple FEs for same adapter. After that it is possible to register two FEs for same adapter. For example one for DVB-T and one for DVB-C. Signed-off-by:
-
Antti Palosaari authored
Signed-off-by:
-
Antti Palosaari authored
Change firmware download split, which I introduced few patch earlier, a little bit to make it more readable as requested [1]. Anyhow, for some reason this seems to increase compiled binary size 52 bytes, on my AMD64 box, which is rather much for so small change. [1] http://www.spinics.net/lists/linux-media/msg31968.htmlSigned-off-by:
-
Antti Palosaari authored
It is DVB-S/S2 USB box. * DNBU10512IST NIM * STV0903 demod * STV6110 tuner * Intersil ISL6423 LNB controller Signed-off-by:
-
Antti Palosaari authored
It is USB DVB-S/S2 box. Conexant cx24116/cx24118 demod tuner combo Intersil ISL6423 LNB controller Signed-off-by:
-
Antti Palosaari authored
It is very rare I2C adapter hardware which can provide 32kB I2C write as one write. Add .i2c_wr_max option to set desired max packet size. Split transaction to smaller pieces according to that option. Signed-off-by:
-
Anatolij Gustschin authored
Currently video capturing using streaming I/O method doesn't work if capturing to overlay buffer took place before. When enabling the stream we have to check the overlay enable driver flag and reset it so that the interrupt handler won't execute the overlay interrupt path after enabling DMA in streamon routine. Otherwise the capture interrupt won't be handled correctly causing non working VIDIOC_DQBUF ioctl. Signed-off-by:
Anatolij Gustschin <agust@denx.de> Signed-off-by:
-
Anatolij Gustschin authored
Currently the driver enables overlay when running VIDIOC_S_FMT ioctl with fmt type V4L2_BUF_TYPE_VIDEO_OVERLAY. Actually, this is wrong. Add proper VIDIOC_OVERLAY support instead of using VIDIOC_S_FMT for overlay enable. Signed-off-by:
-
Jesper Juhl authored
usb_altnum_to_altsetting() may return NULL. If it does we'll dereference a NULL pointer in drivers/media/video/gspca/stv06xx/stv06xx_pb0100.c::pb0100_start(). As far as I can tell there's not really anything more sensible than -ENODEV that we can return in that situation, but I'm not at all intimate with this code so I'd like a bit of review/comments on this before it's applied. Anyway, here's a proposed patch. Signed-off-by:
Jesper Juhl <jj@chaosbits.net> Cc: Jean-Francois Moine <moinejf@free.fr> Cc: Hans de Goede <hdegoede@redhat.com> Cc: Erik Andren <erik.andren@gmail.com> Signed-off-by:
-
David Härdeman authored
Using ir_raw_event_store_with_filter() saves about 20 lines of code. Signed-off-by:
David Härdeman <david@hardeman.nu> Signed-off-by:
-
David Härdeman authored
If an IR command is sent (using the LIRC userspace) to rc-loopback which doesn't include a trailing space, the result is that the message won't be completely decoded. In addition, "leftovers" from a previous transmission can be left until the next one. Fix this by faking a long silence after the end of TX data. Signed-off-by:
-
David Härdeman authored
This patch adds preliminary IR TX capabilities to the winbond-cir driver. Signed-off-by:
-
David Härdeman authored
Using bool instead of an int helps readability a bit. Signed-off-by:
-
Detlev Casanova authored
The MT9V032 is a parallel wide VGA sensor from Aptina (formerly Micron) controlled through I2C. The driver creates a V4L2 subdevice. It currently supports binning and cropping, and the gain, auto gain, exposure, auto exposure and test pattern controls. Signed-off-by:
Detlev Casanova <detlev.casanova@gmail.com> Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
-
Malcolm Priestley authored
Bits 4 and 5 on register 02 should always be set to 1. Opera1/Bsru6/z0194a/mantis_vp1033 Signed-off-by:
Malcolm Priestley <tvboxspy@gmail.com> Acked-by:
Oliver Endriss <o.endriss@gmx.de> Signed-off-by:
-
Malcolm Priestley authored
Issues with Register 02 causing spurious channel locking from standby. Should have always bits 4 & 5 written to 1. Lower nibble not used in any current driver. Usage if necessary can be applied through initab to mcr_reg. stv0299 not out of standby before writing inittab. Signed-off-by:
-
Anatolij Gustschin authored
Use the core-assisted locking in fsl-viu driver and switch to .unlocked_ioctl. Signed-off-by:
-
Jonathan Nieder authored
users is always read or written with core->lock held. A plain int is simpler and faster. Tested-by:
Andi Huber <hobrom@gmx.at> Tested-by:
Marlon de Boer <marlon@hyves.nl> Signed-off-by:
Jonathan Nieder <jrnieder@gmail.com> Signed-off-by:
-
Jonathan Nieder authored
mpeg_users is always read or written with core->lock held except in mpeg_release (where it looks like a bug). A plain int is simpler and faster. Tested-by:
-
Jonathan Nieder authored
It should not be possible to enter mpeg_open and acquire core->lock without the blackbird driver being registered, so just error out if it is not. This makes the code more readable and should prevent the bug fixed by the patch "hold device lock during sub-driver initialization" from resurfacing again. Similarly, if we enter mpeg_release and acquire core->lock then either the blackbird driver is registered (since open files keep it loaded) or the sysadmin forced the driver's removal. In the latter case the state will be inconsistent and this is worth a loud warning. Tested-by:
-
Jonathan Nieder authored
Add and use a mutex to protect the cx88-mpeg device list. Previously the BKL prevented races. Based on work by Ben Hutchings <ben@decadent.org.uk>. Tested-by:
-
Jonathan Nieder authored
cx8802_blackbird_probe makes a device node for the mpeg sub-device before it has been added to dev->drvlist. If the device is opened during that time, the open succeeds but request_acquire cannot be called, so the reference count remains zero. Later, when the device is closed, the reference count becomes negative --- uh oh. Close the race by holding core->lock during probe and not releasing until the device is in drvlist and initialization finished. Previously the BKL prevented this race. Reported-by:
-
Jonathan Nieder authored
The BKL conversion of this driver seems to have gone wrong. Loading the cx88-blackbird driver deadlocks. The cause: mpeg_ops::open in the cx2388x blackbird driver acquires the device lock and calls the sub-driver's request_acquire, which tries to acquire the lock again. Fix it by clarifying the semantics of request_acquire, request_release, advise_acquire, and advise_release: now all will rely on the caller to acquire the device lock. Based on work by Ben Hutchings <ben@decadent.org.uk>. Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=31962Reported-by:
-
Jonathan Nieder authored
The BKL conversion of this driver seems to have gone wrong. Various uses of the sub-device and driver lists appear to be subject to race conditions. In particular, some functions access drvlist without a relevant lock held, which will race against removal of drivers. Let's start with that --- clean up by consistently protecting dev->drvlist with dev->core->lock, noting driver functions that require the device lock to be held or not to be held. After this patch, there are still some races --- e.g., cx8802_blackbird_remove can run between the time the blackbird driver is acquired and the time it is used in mpeg_release, and there's a similar race in cx88_dvb_bus_ctrl. Later patches will address the remaining known races and the deadlock noticed by Andi. This patch just makes the semantics clearer in preparation for those later changes. Based on work by Ben Hutchings <ben@decadent.org.uk>. Tested-by:
-
HIRANO Takahito authored
Signed-off-by:
HIRANO Takahito <hiranotaka@zng.info> Signed-off-by:
-
Ondrej Zary authored
Enabling force_testpattern module parameter in usbvision causes kernel panic. Things like that does not belong to the kernel anyway so the fix is easy. Signed-off-by:
Ondrej Zary <linux@rainbow-software.org> Signed-off-by:
-
Ondrej Zary authored
Add Nogatech USB MicroCam PAL (NV3001P) and NTSC (NV3000N) support to usbvision driver. PAL version is tested, NTSC untested. Data captured using usbsnoop, init_values are listed in the INF file along with image dimensions, offsets and frame rates. Signed-off-by:
-
Malcolm Priestley authored
Improve PID filtering and program register 20 correctly. Make sure stream_on message is sent if streaming is off, otherwise PIDs are not registered. Move mutex outside lme2510_enable_pid. Signed-off-by:
-
Malcolm Priestley authored
usb_buffer not inside mutex lock, waiting caller can alter buffer. Static added to lme2510_exit and lme2510_exit_int. Signed-off-by:
-
Malcolm Priestley authored
Gate could close after first I2C message. On stv0288 it does. Keep 2nd and 3rd message I2C gate control alive. Remove unnecessary gate closing in this module. Signed-off-by:
-
