Hayes Wang says:

====================
r8152: patches for autosuspend

There are unexpected processes when enabling autosuspend.
These patches are used to fix them.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Avoid unnecessary behavior when autosuspend occurs during open().
The relative processes should only be run after finishing open().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If (tp->speed & LINK_STATUS) is not zero, the rtl8152_resume()
would call rtl_start_rx() before enabling the tx/rx. Avoid this
by resetting it to zero.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The flag of SELECTIVE_SUSPEND should be cleared when autoresuming.
Otherwise, when the system suspend and resume occur, it may have
the wrong flow.

Besides, because the flag of SELECTIVE_SUSPEND couldn't be used
to check if the hw enables the relative feature, it should alwayes
be disabled in close().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The WARN_ON in inet_evict_bucket can be triggered by a valid case:
inet_frag_kill and inet_evict_bucket can be running in parallel on the
same queue which means that there has been at least one more ref added
by a previous inet_frag_find call, but inet_frag_kill can delete the
timer before inet_evict_bucket which will cause the WARN_ON() there to
trigger since we'll have refcnt!=1. Now, this case is valid because the
queue is being "killed" for some reason (removed from the chain list and
its timer deleted) so it will get destroyed in the end by one of the
inet_frag_put() calls which reaches 0 i.e. refcnt is still valid.

CC: Florian Westphal <fw@strlen.de>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Patrick McLean <chutzpah@gentoo.org>

Fixes: b13d3cbf ("inet: frag: move eviction of queues to work queue")
Reported-by: Patrick McLean <chutzpah@gentoo.org>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the evictor is running it adds some chosen frags to a local list to
be evicted once the chain lock has been released but at the same time
the *frag_queue can be running for some of the same queues and it
may call inet_frag_kill which will wait on the chain lock and
will then delete the queue from the wrong list since it was added in the
eviction one. The fix is simple - check if the queue has the evict flag
set under the chain lock before deleting it, this is safe because the
evict flag is set only under that lock and having the flag set also means
that the queue has been detached from the chain list, so no need to delete
it again.
An important note to make is that we're safe w.r.t refcnt because
inet_frag_kill and inet_evict_bucket will sync on the del_timer operation
where only one of the two can succeed (or if the timer is executing -
none of them), the cases are:
1. inet_frag_kill succeeds in del_timer
 - then the timer ref is removed, but inet_evict_bucket will not add
   this queue to its expire list but will restart eviction in that chain
2. inet_evict_bucket succeeds in del_timer
 - then the timer ref is kept until the evictor "expires" the queue, but
   inet_frag_kill will remove the initial ref and will set
   INET_FRAG_COMPLETE which will make the frag_expire fn just to remove
   its ref.
In the end all of the queue users will do an inet_frag_put and the one
that reaches 0 will free it. The refcount balance should be okay.

CC: Florian Westphal <fw@strlen.de>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Patrick McLean <chutzpah@gentoo.org>

Fixes: b13d3cbf ("inet: frag: move eviction of queues to work queue")
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: Patrick McLean <chutzpah@gentoo.org>
Tested-by: Patrick McLean <chutzpah@gentoo.org>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

1. Remove the rcu_read_lock/unlock around rcu_access_pointer
2. Replace the rcu_dereference with rcu_access_pointer
Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replaced repetive Device ID's which got added in commit b961f9a4
("cxgb4vf: Remove superfluous "idx" parameter of CH_DEVICE() macro")
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

NetworkManager might want to know that it changed when the router advertisement
arrives.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cc: Vijay Subramanian <vijaynsu@cisco.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>

Olivier Blin says:

====================
cdc-ether: handle promiscuous mode

Since kernel 3.16, my Lenovo USB network adapters (RTL8153) using
cdc-ether are not working anymore in a bridge.

This is due to commit c472ab68, which
resets the packet filter when the device is bound.

The default packet filter set by cdc-ether does not include
promiscuous, while the adapter seemed to have promiscuous enabled by
default.

This patch series allows to support promiscuous mode for cdc-ether, by
hooking into set_rx_mode.

Incidentally, maybe this device should be handled by the r8152 driver,
but this patch series is still nice for other adapters.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Oliver Neukum <oneukum@suse.de>

Promiscuous mode was not supported anymore with my Lenovo adapters
(RTL8153) since commit c472ab68
(cdc-ether: clean packet filter upon probe).

It was not possible to use them in a bridge anymore.
Signed-off-by: Olivier Blin <olivier.blin@softathome.com>
Also-analyzed-by: Loïc Yhuel <loic.yhuel@softathome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This will be used by the set_rx_mode callback.

Also move a comment about multicast filtering in this new function.
Signed-off-by: Olivier Blin <olivier.blin@softathome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To delegate promiscuous mode and multicast filtering to the subdriver.
Signed-off-by: Olivier Blin <olivier.blin@softathome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: systemport: RX path and suspend fixes

These two patches fix a race condition where we have our RX interrupts
enabled, but not NAPI for the RX path, and the second patch fixes an
issue for packets stuck in RX fifo during a suspend/resume cycle.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

bcm_sysport_resume() was missing an UniMAC reset which can lead to
various receive FIFO corruptions coming out of a suspend cycle. If the
RX FIFO is stuck, it will deliver corrupted/duplicate packets towards
the host CPU interface.

This could be reproduced on crowded network and when Wake-on-LAN is
enabled for this particular interface because the switch still forwards
packets towards the host CPU interface (SYSTEMPORT), and we had to leave
the UniMAC RX enable bit on to allow matching MagicPackets.

Once we re-enter the resume function, there is a small window during
which the UniMAC receive is still enabled, and we start queueing
packets, but the RDMA and RBUF engines are not ready, which leads to
having packets stuck in the UniMAC RX FIFO, ultimately delivered towards
the host CPU as corrupted.

Fixes: 40755a0f ("net: systemport: add suspend and resume support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is currently a small window during which the SYSTEMPORT adapter
enables its RX interrupts without having enabled its NAPI handler, which
can result in packets to be discarded during interface bringup.

A similar but more serious window exists in bcm_sysport_resume() during
which we can have the RDMA engine not fully prepared to receive packets
and yet having RX interrupts enabled.

Fix this my moving the RX interrupt enable down to
bcm_sysport_netif_start() after napi_enable() for the RX path is called,
which fixes both call sites: bcm_sysport_open() and
bcm_sysport_resume().

Fixes: b02e6d9b ("net: systemport: add bcm_sysport_netif_{enable,stop}")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix kernel-doc warning in <linux/skbuff.h> by making both headers_start
and headers_end private fields.

Warning(..//include/linux/skbuff.h:654): No description found for parameter 'headers_end[0]'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Marvell phy 88E1145 configuration & initialization was missing a case
for initializing SGMII mode. This patch adds that case.
Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

when slave 0 has no phy and slave 1 connected to phy, driver probe will
fail as there is no phy id present for slave 0 device tree, so continuing
even though no phy-id found, also moving mac-id read later to ensure
mac-id is read from device tree even when phy-id entry in not found.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

John W. Linville says:

====================
pull request: wireless 2014-10-28

Please pull this batch of fixes intended for the 3.18 stream!

For the mac80211 bits, Johannes says:

"Here are a few fixes for the wireless stack: one fixes the
RTS rate, one for a debugfs file, one to return the correct
channel to userspace, a sanity check for a userspace value
and the remaining two are just documentation fixes."

For the iwlwifi bits, Emmanuel says:

"I revert here a patch that caused interoperability issues.
dvm gets a fix for a bug that was reported by many users.
Two minor fixes for BT Coex and platform power fix that helps
reducing latency when the PCIe link goes to low power states."

In addition...

Felix Fietkau adds a couple of ath code fixes related to regulatory
rule enforcement.

Hauke Mehrtens fixes a build break with bcma when CONFIG_OF_ADDRESS
is not set.

Karsten Wiese provides a trio of minor fixes for rtl8192cu.

Kees Cook prevents a potential information leak in rtlwifi.

Larry Finger also brings a trio of minor fixes for rtlwifi.

Rafał Miłecki adds a device ID to the bcma bus driver.

Rickard Strandqvist offers some strn* -> strl* changes in brcmfmac
to eliminate non-terminated string issues.

Sujith Manoharan avoids some ath9k stalls by enabling HW queue control
only for MCC.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Andrew Lunn says:

====================
DSA tagging mismatches

The second patch is a fix, which should be applied to -rc. It is
possible to get a DSA configuration which does not work. The patch
stops this happening.

The first patch detects this situation, and errors out the probe of
DSA, making it more obvious something is wrong. It is not required to
apply it -rc.

v2 fixes the use case pointed out by Florian, that a switch driver
may use DSA_TAG_PROTO_NONE which the patch did not correctly handle.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The mv88e6171 can support two different tagging protocols, DSA and
EDSA. The switch driver structure only allows one protocol to be
enumerated, and DSA was chosen. However the Kconfig entry ensures the
EDSA tagging code is built. With a minimal configuration, we then end
up with a mismatch. The probe is successful, EDSA tagging is used, but
the switch is configured for DSA, resulting in mangled packets.

Change the switch driver structure to enumerate EDSA, fixing the
mismatch.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 42f27253 ("net: DSA: Marvell mv88e6171 switch driver")
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If there is a mismatch between enabled tagging protocols and the
protocol the switch supports, error out, rather than continue with a
situation which is unlikely to work.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
cc: alexander.h.duyck@intel.com
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

introduce two configs:
- hidden CONFIG_BPF to select eBPF interpreter that classic socket filters
  depend on
- visible CONFIG_BPF_SYSCALL (default off) that tracing and sockets can use

that solves several problems:
- tracing and others that wish to use eBPF don't need to depend on NET.
  They can use BPF_SYSCALL to allow loading from userspace or select BPF
  to use it directly from kernel in NET-less configs.
- in 3.18 programs cannot be attached to events yet, so don't force it on
- when the rest of eBPF infra is there in 3.19+, it's still useful to
  switch it off to minimize kernel size

bloat-o-meter on x64 shows:
add/remove: 0/60 grow/shrink: 0/2 up/down: 0/-15601 (-15601)

tested with many different config combinations. Hopefully didn't miss anything.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Anish Bhatt says:

====================
cxgb4 : DCBx fixes for apps/host lldp agents

This patchset  contains some minor fixes for cxgb4 DCBx code. Chiefly, cxgb4
was not cleaning up any apps added to kernel app table when link was lost.
Disabling DCBx in firmware would automatically set DCBx state to host-managed
and enabled, we now wait for an explicit enable call from an lldp agent instead

First patch was originally sent to net-next, but considering it applies to
correcting behaviour of code already in net, I think it qualifies as a bug fix.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Disabling DCBx in firmware automatically enables DCBx for control via host
lldp agents. Wait for an explicit setstate call from an lldp agents to enable
 DCBx instead.

Fixes: 76bcb31e ("cxgb4 : Add DCBx support codebase and dcbnl_ops")
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Clear out any DCB apps we might have added to kernel table when we lose DCB
sync (or IEEE equivalent event). These were previously left behind and not
cleaned up correctly. IEEE allows individual components to work independently,
 so improve check for IEEE completion by specifying individual components.

Fixes: 10b00466 ("cxgb4: IEEE fixes for DCBx state machine")
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter fixes for net

The following patchset contains Netfilter fixes for your net tree,
they are:

1) Allow to recycle a TCP port in conntrack when the change role from
   server to client, from Marcelo Leitner.

2) Fix possible off by one access in ip_set_nfnl_get_byindex(), patch
   from Dan Carpenter.

3) alloc_percpu returns NULL on error, no need for IS_ERR() in nf_tables
   chain statistic updates. From Sabrina Dubroca.

4) Don't compile ip options in bridge netfilter, this mangles the packet
   and bridge should not alter layer >= 3 headers when forwarding packets.
   Patch from Herbert Xu and tested by Florian Westphal.

5) Account the final NLMSG_DONE message when calculating the size of the
   nflog netlink batches. Patch from Florian Westphal.

6) Fix a possible netlink attribute length overflow with large packets.
   Again from Florian Westphal.

7) Release the skbuff if nfnetlink_log fails to put the final
   NLMSG_DONE message. This fixes a leak on error. This shouldn't ever
   happen though, otherwise this means we miscalculate the netlink batch
   size, so spot a warning if this ever happens so we can track down the
   problem. This patch from Houcheng Lin.

8) Look at the right list when recycling targets in the nft_compat,
   patch from Arturo Borrero.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The code looks for an already loaded target, and the correct list to search
is nft_target_list, not nft_match_list.
Signed-off-by: Arturo Borrero Gonzalez <arturo.borrero.glez@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Merge tag 'mac80211-for-john-2014-10-23' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg <johannes@sipsolutions.net> says:

"Here are a few fixes for the wireless stack: one fixes the
RTS rate, one for a debugfs file, one to return the correct
channel to userspace, a sanity check for a userspace value
and the remaining two are just documentation fixes."
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge tag 'iwlwifi-for-john-2014-10-23' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes

Emmanuel Grumbach <egrumbach@gmail.com> says:

"I revert here a patch that caused interoperability issues.
dvm gets a fix for a bug that was reported by many users.
Two minor fixes for BT Coex and platform power fix that helps
reducing latency when the PCIe link goes to low power states."
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Do not reuse skb if it was pfmemalloc tainted, otherwise
future frame might be dropped anyway.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Roman Gushchin <klamm@yandex-team.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eli Cohen says:

====================
irq sync fixes

This two patch series fixes a race where an interrupt handler could access a
freed memory.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

After moving the EQ ownership to software effectively destroying it, call
synchronize_irq() to ensure that any handler routines running on other CPU
cores finish execution. Only then free the EQ buffer.
The same thing is done when we destroy a CQ which is one of the sources
generating interrupts. In the case of CQ we want to avoid completion handlers
on a CQ that was destroyed. In the case we do the same to avoid receiving
asynchronous events after the EQ has been destroyed and its buffers freed.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After destroying the EQ, the object responsible for generating interrupts, call
synchronize_irq() to ensure that any handler routines running on other CPU
cores finish execution. Only then free the EQ buffer. This patch solves a very
rare case when we get panic on driver unload.
The same thing is done when we destroy a CQ which is one of the sources
generating interrupts. In the case of CQ we want to avoid completion handlers
on a CQ that was destroyed. In the case we do the same to avoid receiving
asynchronous events after the EQ has been destroyed and its buffers freed.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/apm/xgene/xgene_enet_sgmac.c: In function ‘xgene_enet_ecc_init’:
drivers/net/ethernet/apm/xgene/xgene_enet_sgmac.c:126: warning: ‘data’ may be used uninitialized in this function

Depending on the arbitrary value on the stack, the loop may terminate
too early, and cause a bogus -ENODEV failure.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

We accidentally mask by the _SHIFT variable.  It means that "event" is
always zero.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We need to cancel the work queue after rcu grace period,
otherwise it can be rescheduled by incoming packets.

We need to purge queue if some skbs are still in it.

We can use __skb_queue_head_init() variant in
macvlan_process_broadcast()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 412ca155 ("macvlan: Move broadcasts into a work queue")
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

percpu tcp_md5sig_pool contains memory blobs that ultimately
go through sg_set_buf().

-> sg_set_page(sg, virt_to_page(buf), buflen, offset_in_page(buf));

This requires that whole area is in a physically contiguous portion
of memory. And that @buf is not backed by vmalloc().

Given that alloc_percpu() can use vmalloc() areas, this does not
fit the requirements.

Replace alloc_percpu() by a static DEFINE_PER_CPU() as tcp_md5sig_pool
is small anyway, there is no gain to dynamically allocate it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 765cf997 ("tcp: md5: remove one indirection level in tcp_md5sig_pool")
Reported-by: Crestez Dan Leonard <cdleonard@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>