- 20 Jan, 2016 32 commits
-
-
Krzysztof Hałasa authored
commit 3a35e470 upstream. Gateworks Ventana boards seem to need "RGMII-ID" (internal delay) PHY mode, instead of simple "RGMII", for their Marvell 88E1510 transceiver. Otherwise, the Ethernet MAC doesn't work with Marvell PHY driver (TX doesn't seem to work correctly). Tested on GW5400 rev. C. This bug affects ARM Fedora 23. Signed-off-by:
Krzysztof Hałasa <khalasa@piap.pl> Acked-by:
Tim Harvey <tharvey@gateworks.com> Signed-off-by:
Shawn Guo <shawnguo@kernel.org> Signed-off-by:
Kamal Mostafa <kamal@canonical.com>
-
Anssi Hannula authored
commit 42e3121d upstream. AudioQuest DragonFly DAC reports a volume control range of 0..50 (0x0000..0x0032) which in USB Audio means a range of 0 .. 0.2dB, which is obviously incorrect and would cause software using the dB information in e.g. volume sliders to have a massive volume difference in 100..102% range. Commit 2d1cb7f6 ("ALSA: usb-audio: add dB range mapping for some devices") added a dB range mapping for it with range 0..50 dB. However, the actual volume mapping seems to be neither linear volume nor linear dB scale, but instead quite close to the cubic mapping e.g. alsamixer uses, with a range of approx. -53...0 dB. Replace the previous quirk with a custom dB mapping based on some basic output measurements, using a 10-item range TLV (which will still fit in alsa-lib MAX_TLV_RANGE_SIZE). Tested on AudioQuest DragonFly HW v1.2. The quirk is only applied if the range is 0..50, so if this gets fixed/changed in later HW revisions it will no longer be applied. v2: incorporated Takashi Iwai's suggestion for the quirk application method Signed-off-by:
Anssi Hannula <anssi.hannula@iki.fi> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Thomas Gleixner authored
commit abc7e40c upstream. If a interrupt chip utilizes chip->buslock then free_irq() can deadlock in the following way: CPU0 CPU1 interrupt(X) (Shared or spurious) free_irq(X) interrupt_thread(X) chip_bus_lock(X) irq_finalize_oneshot(X) chip_bus_lock(X) synchronize_irq(X) synchronize_irq() waits for the interrupt thread to complete, i.e. forever. Solution is simple: Drop chip_bus_lock() before calling synchronize_irq() as we do with the irq_desc lock. There is nothing to be protected after the point where irq_desc lock has been released. This adds chip_bus_lock/unlock() to the remove_irq() code path, but that's actually correct in the case where remove_irq() is called on such an interrupt. The current users of remove_irq() are not affected as none of those interrupts is on a chip which requires buslock. Reported-by:
Fredrik Markström <fredrik.markstrom@gmail.com> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Peter Hurley authored
commit 9ce119f3 upstream. A line discipline which does not define a receive_buf() method can can cause a GPF if data is ever received [1]. Oddly, this was known to the author of n_tracesink in 2011, but never fixed. [1] GPF report BUG: unable to handle kernel NULL pointer dereference at (null) IP: [< (null)>] (null) PGD 3752d067 PUD 37a7b067 PMD 0 Oops: 0010 [#1] SMP KASAN Modules linked in: CPU: 2 PID: 148 Comm: kworker/u10:2 Not tainted 4.4.0-rc2+ #51 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 Workqueue: events_unbound flush_to_ldisc task: ffff88006da94440 ti: ffff88006db60000 task.ti: ffff88006db60000 RIP: 0010:[<0000000000000000>] [< (null)>] (null) RSP: 0018:ffff88006db67b50 EFLAGS: 00010246 RAX: 0000000000000102 RBX: ffff88003ab32f88 RCX: 0000000000000102 RDX: 0000000000000000 RSI: ffff88003ab330a6 RDI: ffff88003aabd388 RBP: ffff88006db67c48 R08: ffff88003ab32f9c R09: ffff88003ab31fb0 R10: ffff88003ab32fa8 R11: 0000000000000000 R12: dffffc0000000000 R13: ffff88006db67c20 R14: ffffffff863df820 R15: ffff88003ab31fb8 FS: 0000000000000000(0000) GS:ffff88006dc00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b CR2: 0000000000000000 CR3: 0000000037938000 CR4: 00000000000006e0 Stack: ffffffff829f46f1 ffff88006da94bf8 ffff88006da94bf8 0000000000000000 ffff88003ab31fb0 ffff88003aabd438 ffff88003ab31ff8 ffff88006430fd90 ffff88003ab32f9c ffffed0007557a87 1ffff1000db6cf78 ffff88003ab32078 Call Trace: [<ffffffff8127cf91>] process_one_work+0x8f1/0x17a0 kernel/workqueue.c:2030 [<ffffffff8127df14>] worker_thread+0xd4/0x1180 kernel/workqueue.c:2162 [<ffffffff8128faaf>] kthread+0x1cf/0x270 drivers/block/aoe/aoecmd.c:1302 [<ffffffff852a7c2f>] ret_from_fork+0x3f/0x70 arch/x86/entry/entry_64.S:468 Code: Bad RIP value. RIP [< (null)>] (null) RSP <ffff88006db67b50> CR2: 0000000000000000 ---[ end trace a587f8947e54d6ea ]--- Reported-by:
Dmitry Vyukov <dvyukov@google.com> Signed-off-by:
Peter Hurley <peter@hurleysoftware.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Peter Hurley authored
commit ac8f3bf8 upstream. commit 40d5e090 ("n_tty: Fix EOF push handling") fixed EOF push for reads. However, that approach still allows a condition mismatch between poll() and read(), where poll() returns POLLIN but read() blocks. This state can happen when a previous read() returned because the user buffer was full and the next character was an EOF not at the beginning of the line. While the next read() will properly identify the condition and advance the read buffer tail without improperly indicating an EOF file condition (ie., read() will not mistakenly return 0), poll() will mistakenly indicate POLLIN. Although a possible solution would be to peek at the input buffer in n_tty_poll(), the better solution in this patch is to eat the EOF during the previous read() (ie., fix the problem by eliminating the condition). The current canon line buffer copy limits the scan for next end-of-line to the smaller of either, a. the remaining user buffer size b. completed lines in the input buffer When the remaining user buffer size is exactly one less than the end-of-line marked by EOF push, the EOF is not scanned nor skipped but left for subsequent reads. In the example below, the scan index 'eol' has stopped at the EOF because it is past the scan limit of 5 (not because it has found the next set bit in read_flags) user buffer [*nr = 5] _ _ _ _ _ read_flags 0 0 0 0 0 1 input buffer h e l l o [EOF] ^ ^ / / tail eol result: found = 0, tail += 5, *nr += 5 Instead, allow the scan to peek ahead 1 byte (while still limiting the scan to completed lines in the input buffer). For the example above, result: found = 1, tail += 6, *nr += 5 Because the scan limit is now bumped +1 byte, when the scan is completed, the tail advance and the user buffer copy limit is re-clamped to *nr when EOF is _not_ found. Fixes: 40d5e090 ("n_tty: Fix EOF push handling") Signed-off-by:
Luis Henriques <luis.henriques@canonical.com> Signed-off-by:
-
Mans Rullgard authored
commit 1ea5998a upstream. Attempting to use this codec driver triggers a BUG() in regcache_sync() since no cache type is set. The register map of this device is fairly small and has few holes so a flat cache is suitable. Signed-off-by:
Mans Rullgard <mans@mansr.com> Acked-by:
Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Dmitry V. Levin authored
commit 2d33fa10 upstream. According to arch/sh/kernel/syscalls_64.S and common sense, __NR_fgetxattr has to be defined to 259, but it doesn't. Instead, it's defined to 269, which is of course used by another syscall, __NR_sched_setaffinity in this case. This bug was found by strace test suite. Signed-off-by:
Dmitry V. Levin <ldv@altlinux.org> Acked-by:
Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Junxiao Bi authored
commit 854ee2e9 upstream. Commit 8f1eb487 ("ocfs2: fix umask ignored issue") introduced an issue, SGID of sub dir was not inherited from its parents dir. It is because SGID is set into "inode->i_mode" in ocfs2_get_init_inode(), but is overwritten by "mode" which don't have SGID set later. Fixes: 8f1eb487 ("ocfs2: fix umask ignored issue") Signed-off-by:
Junxiao Bi <junxiao.bi@oracle.com> Cc: Mark Fasheh <mfasheh@suse.de> Cc: Joel Becker <jlbec@evilplan.org> Acked-by:
Srinivas Eeda <srinivas.eeda@oracle.com> Signed-off-by:
-
Seth Jennings authored
commit 26bbe7ef upstream. Commit bdee237c ("x86: mm: Use 2GB memory block size on large-memory x86-64 systems") and 982792c7 ("x86, mm: probe memory block size for generic x86 64bit") introduced large block sizes for x86. This made it possible to have multiple sections per memory block where previously, there was a only every one section per block. Since blocks consist of contiguous ranges of section, there can be holes in the blocks where sections are not present. If one attempts to offline such a block, a crash occurs since the code is not designed to deal with this. This patch is a quick fix to gaurd against the crash by not allowing blocks with non-present sections to be offlined. Addresses https://bugzilla.kernel.org/show_bug.cgi?id=107781Signed-off-by:
Seth Jennings <sjennings@variantweb.net> Reported-by:
Andrew Banman <abanman@sgi.com> Cc: Daniel J Blueman <daniel@numascale.com> Cc: Yinghai Lu <yinghai@kernel.org> Cc: Greg KH <greg@kroah.com> Cc: Russ Anderson <rja@sgi.com> Signed-off-by:
-
Naoya Horiguchi authored
commit 0d777df5 upstream. Currently at the beginning of hugetlb_fault(), we call huge_pte_offset() and check whether the obtained *ptep is a migration/hwpoison entry or not. And if not, then we get to call huge_pte_alloc(). This is racy because the *ptep could turn into migration/hwpoison entry after the huge_pte_offset() check. This race results in BUG_ON in huge_pte_alloc(). We don't have to call huge_pte_alloc() when the huge_pte_offset() returns non-NULL, so let's fix this bug with moving the code into else block. Note that the *ptep could turn into a migration/hwpoison entry after this block, but that's not a problem because we have another !pte_present check later (we never go into hugetlb_no_page() in that case.) Fixes: 290408d4 ("hugetlb: hugepage migration core") Signed-off-by:
Naoya Horiguchi <n-horiguchi@ah.jp.nec.com> Acked-by:
Hillf Danton <hillf.zj@alibaba-inc.com> Acked-by:
David Rientjes <rientjes@google.com> Cc: Hugh Dickins <hughd@google.com> Cc: Dave Hansen <dave.hansen@intel.com> Cc: Mel Gorman <mgorman@suse.de> Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com> Cc: Mike Kravetz <mike.kravetz@oracle.com> Signed-off-by:
-
Michal Hocko authored
commit 373ccbe5 upstream. Tetsuo Handa has reported that the system might basically livelock in OOM condition without triggering the OOM killer. The issue is caused by internal dependency of the direct reclaim on vmstat counter updates (via zone_reclaimable) which are performed from the workqueue context. If all the current workers get assigned to an allocation request, though, they will be looping inside the allocator trying to reclaim memory but zone_reclaimable can see stalled numbers so it will consider a zone reclaimable even though it has been scanned way too much. WQ concurrency logic will not consider this situation as a congested workqueue because it relies that worker would have to sleep in such a situation. This also means that it doesn't try to spawn new workers or invoke the rescuer thread if the one is assigned to the queue. In order to fix this issue we need to do two things. First we have to let wq concurrency code know that we are in trouble so we have to do a short sleep. In order to prevent from issues handled by 0e093d99 ("writeback: do not sleep on the congestion queue if there are no congested BDIs or if significant congestion is not being encountered in the current zone") we limit the sleep only to worker threads which are the ones of the interest anyway. The second thing to do is to create a dedicated workqueue for vmstat and mark it WQ_MEM_RECLAIM to note it participates in the reclaim and to have a spare worker thread for it. Signed-off-by:
Michal Hocko <mhocko@suse.com> Reported-by:
Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Cc: Tejun Heo <tj@kernel.org> Cc: Cristopher Lameter <clameter@sgi.com> Cc: Joonsoo Kim <js1304@gmail.com> Cc: Arkadiusz Miskiewicz <arekm@maven.pl> Signed-off-by:
-
Christoph Lameter authored
commit 57c2e36b upstream. It was noted that the vm stat shepherd runs every 2 seconds and that the vmstat update is then scheduled 2 seconds in the future. This yields an interval of double the time interval which is not desired. Change the shepherd so that it does not delay the vmstat update on the other cpu. We stil have to use schedule_delayed_work since we are using a delayed_work_struct but we can set the delay to 0. Signed-off-by:
Christoph Lameter <cl@linux.com> Acked-by:
Michal Hocko <mhocko@suse.cz> Cc: Vinayak Menon <vinmenon@codeaurora.org> Signed-off-by:
-
Naoya Horiguchi authored
commit a88c7695 upstream. When dequeue_huge_page_vma() in alloc_huge_page() fails, we fall back on alloc_buddy_huge_page() to directly create a hugepage from the buddy allocator. In that case, however, if alloc_buddy_huge_page() succeeds we don't decrement h->resv_huge_pages, which means that successful hugetlb_fault() returns without releasing the reserve count. As a result, subsequent hugetlb_fault() might fail despite that there are still free hugepages. This patch simply adds decrementing code on that code path. I reproduced this problem when testing v4.3 kernel in the following situation: - the test machine/VM is a NUMA system, - hugepage overcommiting is enabled, - most of hugepages are allocated and there's only one free hugepage which is on node 0 (for example), - another program, which calls set_mempolicy(MPOL_BIND) to bind itself to node 1, tries to allocate a hugepage, - the allocation should fail but the reserve count is still hold. Signed-off-by:
-
Mikulas Patocka authored
commit e46e31a3 upstream. When using the Promise TX2+ SATA controller on PA-RISC, the system often crashes with kernel panic, for example just writing data with the dd utility will make it crash. Kernel panic - not syncing: drivers/parisc/sba_iommu.c: I/O MMU @ 000000000000a000 is out of mapping resources CPU: 0 PID: 18442 Comm: mkspadfs Not tainted 4.4.0-rc2 #2 Backtrace: [<000000004021497c>] show_stack+0x14/0x20 [<0000000040410bf0>] dump_stack+0x88/0x100 [<000000004023978c>] panic+0x124/0x360 [<0000000040452c18>] sba_alloc_range+0x698/0x6a0 [<0000000040453150>] sba_map_sg+0x260/0x5b8 [<000000000c18dbb4>] ata_qc_issue+0x264/0x4a8 [libata] [<000000000c19535c>] ata_scsi_translate+0xe4/0x220 [libata] [<000000000c19a93c>] ata_scsi_queuecmd+0xbc/0x320 [libata] [<0000000040499bbc>] scsi_dispatch_cmd+0xfc/0x130 [<000000004049da34>] scsi_request_fn+0x6e4/0x970 [<00000000403e95a8>] __blk_run_queue+0x40/0x60 [<00000000403e9d8c>] blk_run_queue+0x3c/0x68 [<000000004049a534>] scsi_run_queue+0x2a4/0x360 [<000000004049be68>] scsi_end_request+0x1a8/0x238 [<000000004049de84>] scsi_io_completion+0xfc/0x688 [<0000000040493c74>] scsi_finish_command+0x17c/0x1d0 The cause of the crash is not exhaustion of the IOMMU space, there is plenty of free pages. The function sba_alloc_range is called with size 0x11000, thus the pages_needed variable is 0x11. The function sba_search_bitmap is called with bits_wanted 0x11 and boundary size is 0x10 (because dma_get_seg_boundary(dev) returns 0xffff). The function sba_search_bitmap attempts to allocate 17 pages that must not cross 16-page boundary - it can't satisfy this requirement (iommu_is_span_boundary always returns true) and fails even if there are many free entries in the IOMMU space. How did it happen that we try to allocate 17 pages that don't cross 16-page boundary? The cause is in the function iommu_coalesce_chunks. This function tries to coalesce adjacent entries in the scatterlist. The function does several checks if it may coalesce one entry with the next, one of those checks is this: if (startsg->length + dma_len > max_seg_size) break; When it finishes coalescing adjacent entries, it allocates the mapping: sg_dma_len(contig_sg) = dma_len; dma_len = ALIGN(dma_len + dma_offset, IOVP_SIZE); sg_dma_address(contig_sg) = PIDE_FLAG | (iommu_alloc_range(ioc, dev, dma_len) << IOVP_SHIFT) | dma_offset; It is possible that (startsg->length + dma_len > max_seg_size) is false (we are just near the 0x10000 max_seg_size boundary), so the funcion decides to coalesce this entry with the next entry. When the coalescing succeeds, the function performs dma_len = ALIGN(dma_len + dma_offset, IOVP_SIZE); And now, because of non-zero dma_offset, dma_len is greater than 0x10000. iommu_alloc_range (a pointer to sba_alloc_range) is called and it attempts to allocate 17 pages for a device that must not cross 16-page boundary. To fix the bug, we must make sure that dma_len after addition of dma_offset and alignment doesn't cross the segment boundary. I.e. change if (startsg->length + dma_len > max_seg_size) break; to if (ALIGN(dma_len + dma_offset + startsg->length, IOVP_SIZE) > max_seg_size) break; This patch makes this change (it precalculates max_seg_boundary at the beginning of the function iommu_coalesce_chunks). I also added a check that the mapping length doesn't exceed dma_get_seg_boundary(dev) (it is not needed for Promise TX2+ SATA, but it may be needed for other devices that have dma_get_seg_boundary lower than dma_get_max_seg_size). Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
Helge Deller <deller@gmx.de> Signed-off-by:
-
Prarit Bhargava authored
commit 79a21dbf upstream. Intel RAPL initialized on several systems where the BIOS lock bit (msr 0x610, bit 63) was set. This occured because the return value of rapl_read_data_raw() was being checked, rather than the value of the variable passed in, locked. This patch properly implments the rapl_read_data_raw() call to check the variable locked, and now the Intel RAPL driver outputs the warning: intel_rapl: RAPL package 0 domain package locked by BIOS and does not initialize for the package. Signed-off-by:
Prarit Bhargava <prarit@redhat.com> Acked-by:
Jacob Pan <jacob.jun.pan@linux.intel.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Alan Stern authored
commit ad87e032 upstream. Some USB device / host controller combinations seem to have problems with Link Power Management. For example, Steinar found that his xHCI controller wouldn't handle bandwidth calculations correctly for two video cards simultaneously when LPM was enabled, even though the bus had plenty of bandwidth available. This patch introduces a new quirk flag for devices that should remain disabled for LPM, and creates quirk entries for Steinar's devices. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Reported-by:
Steinar H. Gunderson <sgunderson@bigfoot.com> Signed-off-by:
-
Mathias Nyman authored
commit f69115fd upstream. According to USB 2 specs ports need to signal resume for at least 20ms, in practice even longer, before moving to U0 state. Both host and devices can initiate resume. On device initiated resume, a port status interrupt with the port in resume state in issued. The interrupt handler tags a resume_done[port] timestamp with current time + USB_RESUME_TIMEOUT, and kick roothub timer. Root hub timer requests for port status, finds the port in resume state, checks if resume_done[port] timestamp passed, and set port to U0 state. On host initiated resume, current code sets the port to resume state, sleep 20ms, and finally sets the port to U0 state. This should also be changed to work in a similar way as the device initiated resume, with timestamp tagging, but that is not yet tested and will be a separate fix later. There are a few issues with this approach 1. A host initiated resume will also generate a resume event. The event handler will find the port in resume state, believe it's a device initiated resume, and act accordingly. 2. A port status request might cut the resume signalling short if a get_port_status request is handled during the host resume signalling. The port will be found in resume state. The timestamp is not set leading to time_after_eq(jiffies, timestamp) returning true, as timestamp = 0. get_port_status will proceed with moving the port to U0. 3. If an error, or anything else happens to the port during device initiated resume signalling it will leave all the device resume parameters hanging uncleared, preventing further suspend, returning -EBUSY, and cause the pm thread to busyloop trying to enter suspend. Fix this by using the existing resuming_ports bitfield to indicate that resume signalling timing is taken care of. Check if the resume_done[port] is set before using it for timestamp comparison, and also clear out any resume signalling related variables if port is not in U0 or Resume state This issue was discovered when a PM thread busylooped, trying to runtime suspend the xhci USB 2 roothub on a Dell XPS Reported-by:
Daniel J Blueman <daniel@quora.org> Tested-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
James Bottomley authored
commit 5e103356 upstream. KASAN found that our additional element processing scripts drop off the end of the VPD page into unallocated space. The reason is that not every element has additional information but our traversal routines think they do, leading to them expecting far more additional information than is present. Fix this by adding a gate to the traversal routine so that it only processes elements that are expected to have additional information (list is in SES-2 section 6.1.13.1: Additional Element Status diagnostic page overview) Reported-by:
Pavel Tikhomirov <ptikhomirov@virtuozzo.com> Tested-by:
James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by:
-
Stefan Agner authored
commit 9c171905 upstream. Linux on Vybrid used several different L2 latencies so far, none of them seem to be the right ones. According to the application note AN4947 ("Understanding Vybrid Architecture"), the tag portion runs on CPU clock and is inside the L2 cache controller, whereas the data portion is stored in the external SRAM running on platform clock. Hence it is likely that the correct value requires a higher data latency then tag latency. These are the values which have been used so far: - The mainline values: arm,data-latency = <1 1 1>; arm,tag-latency = <2 2 2>; Those values have lead to problems on higher clocks. They look like a poor translation from the reset values (missing +1 offset and a mix up between tag/latency values). - The Linux 3.0 (SoC vendor BSP) values (converted to DT notation): arm,data-latency = <4 2 3> arm,tag-latency = <4 2 3> The cache initialization function along with the value matches the i.MX6 code from the same kernel, so it seems that those values have just been copied. - The Colibri values: arm,data-latency = <2 1 2>; arm,tag-latency = <3 2 3>; Those were a mix between the values of the Linux 3.0 based BSP and the mainline values above. - The SoC Reset values (converted to DT notation): arm,data-latency = <3 3 3>; arm,tag-latency = <2 2 2>; So far there is no official statement on what the correct values are. See also the related Freescale community thread: https://community.freescale.com/message/579785#579785 For now, the reset values seem to be the best bet. Remove all other "bogus" values and use the reset value on vf610.dtsi level. Signed-off-by:
Stefan Agner <stefan@agner.ch> Signed-off-by:
-
Peter Ujfalusi authored
commit e2a0c9fa upstream. The condition for checking for XDAT being cleared was not correct. Fixes: 36bcecd0 ("ASoC: davinci-mcasp: Correct TX start sequence") Signed-off-by:
Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by:
-
Kirill A. Shutemov authored
commit 9f5bd308 upstream. There are few defects in vga_get() related to signal hadning: - we shouldn't check for pending signals for TASK_UNINTERRUPTIBLE case; - if we found pending signal we must remove ourself from wait queue and change task state back to running; - -ERESTARTSYS is more appropriate, I guess. Signed-off-by:
Kirill A. Shutemov <kirill@shutemov.name> Reviewed-by:
David Herrmann <dh.herrmann@gmail.com> Signed-off-by:
Dave Airlie <airlied@redhat.com> Signed-off-by:
-
James Bottomley authored
commit 3417c1b5 upstream. Simple enclosure implementations (mostly USB) are allowed to return only page 8 to every diagnostic query. That really confuses our implementation because we assume the return is the page we asked for and end up doing incorrect offsets based on bogus information leading to accesses outside of allocated ranges. Fix that by checking the page code of the return and giving an error if it isn't the one we asked for. This should fix reported bugs with USB storage by simply refusing to attach to enclosures that behave like this. It's also good defensive practise now that we're starting to see more USB enclosures. Reported-by:
Andrea Gelmini <andrea.gelmini@gelma.net> Reviewed-by:
Ewan D. Milne <emilne@redhat.com> Reviewed-by:
Tomas Henzl <thenzl@redhat.com> Signed-off-by:
-
Joe Thornber authored
commit ed8b45a3 upstream. If dm_btree_del()'s call to push_frame() fails, e.g. due to btree_node_validator finding invalid metadata, the dm_btree_del() error path must unlock all frames (which have active dm-bufio buffers) that were pushed onto the del_stack. Otherwise, dm_bufio_client_destroy() will BUG_ON() because dm-bufio buffers have leaked, e.g.: device-mapper: bufio: leaked buffer 3, hold count 1, list 0 Signed-off-by:
Joe Thornber <ejt@redhat.com> Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
-
Johannes Berg authored
commit b7bb1100 upstream. Some users of rfkill, like NFC and cfg80211, use a dynamic name when allocating rfkill, in those cases dev_name(). Therefore, the pointer passed to rfkill_alloc() might not be valid forever, I specifically found the case that the rfkill name was quite obviously an invalid pointer (or at least garbage) when the wiphy had been renamed. Fix this by making a copy of the rfkill name in rfkill_alloc(). Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Paul Mackerras authored
commit c20875a3 upstream. Currently it is possible for userspace (e.g. QEMU) to set a value for the MSR for a guest VCPU which has both of the TS bits set, which is an illegal combination. The result of this is that when we execute a hrfid (hypervisor return from interrupt doubleword) instruction to enter the guest, the CPU will take a TM Bad Thing type of program interrupt (vector 0x700). Now, if PR KVM is configured in the kernel along with HV KVM, we actually handle this without crashing the host or giving hypervisor privilege to the guest; instead what happens is that we deliver a program interrupt to the guest, with SRR0 reflecting the address of the hrfid instruction and SRR1 containing the MSR value at that point. If PR KVM is not configured in the kernel, then we try to run the host's program interrupt handler with the MMU set to the guest context, which almost certainly causes a host crash. This closes the hole by making kvmppc_set_msr_hv() check for the illegal combination and force the TS field to a safe value (00, meaning non-transactional). Signed-off-by:
Paul Mackerras <paulus@samba.org> Signed-off-by:
-
John Keeping authored
commit 84ebac4d upstream. This is using completely the wrong mask and value when updating the register. Since the correct values are already defined in the header, switch to using a table with explicit constants rather than shifting the array index. Signed-off-by:
John Keeping <john@metanate.com> Signed-off-by:
-
Jan Stancek authored
commit 27f972d3 upstream. We encountered a panic on boot in ipmi_si on a dell per320 due to an uninitialized timer as follows. static int smi_start_processing(void *send_info, ipmi_smi_t intf) { /* Try to claim any interrupts. */ if (new_smi->irq_setup) new_smi->irq_setup(new_smi); --> IRQ arrives here and irq handler tries to modify uninitialized timer which triggers BUG_ON(!timer->function) in __mod_timer(). Call Trace: <IRQ> [<ffffffffa0532617>] start_new_msg+0x47/0x80 [ipmi_si] [<ffffffffa053269e>] start_check_enables+0x4e/0x60 [ipmi_si] [<ffffffffa0532bd8>] smi_event_handler+0x1e8/0x640 [ipmi_si] [<ffffffff810f5584>] ? __rcu_process_callbacks+0x54/0x350 [<ffffffffa053327c>] si_irq_handler+0x3c/0x60 [ipmi_si] [<ffffffff810efaf0>] handle_IRQ_event+0x60/0x170 [<ffffffff810f245e>] handle_edge_irq+0xde/0x180 [<ffffffff8100fc59>] handle_irq+0x49/0xa0 [<ffffffff8154643c>] do_IRQ+0x6c/0xf0 [<ffffffff8100ba53>] ret_from_intr+0x0/0x11 /* Set up the timer that drives the interface. */ setup_timer(&new_smi->si_timer, smi_timeout, (long)new_smi); The following patch fixes the problem. To: Openipmi-developer@lists.sourceforge.net To: Corey Minyard <minyard@acm.org> CC: linux-kernel@vger.kernel.org Signed-off-by:
Jan Stancek <jstancek@redhat.com> Signed-off-by:
Tony Camuso <tcamuso@redhat.com> Signed-off-by:
Corey Minyard <cminyard@mvista.com> Signed-off-by:
-
Joe Thornber authored
commit 50dd842a upstream. When applying block operations (BOPs) do not remove them from the uncommitted BOP ring-buffer until after they've been applied -- in case we recurse. Also, perform BOP_INC operation, in dm_sm_metadata_create() and sm_metadata_extend(), in terms of the uncommitted BOP ring-buffer rather than using direct calls to sm_ll_inc(). Signed-off-by:
-
Joe Thornber authored
commit 49e99fc7 upstream. When you take a metadata snapshot the btree roots for the mapping and details tree need to have their reference counts incremented so they persist for the lifetime of the metadata snap. The roots being incremented were those currently written in the superblock, which could possibly be out of date if concurrent IO is triggering new mappings, breaking of sharing, etc. Fix this by performing a commit with the metadata lock held while taking a metadata snapshot. Signed-off-by:
-
Takashi Iwai authored
commit 9a811230 upstream. Lenovo Thinkpad T440s suffers from constant background noises, and it seems to be a generic hardware issue on this model: https://forums.lenovo.com/t5/ThinkPad-T400-T500-and-newer-T/T440s-speaker-noise/td-p/1339883 As the noise comes from the analog loopback path, disabling the path is the easy workaround. Also, the machine gives significant cracking noises at PM suspend. A workaround found by trial-and-error is to disable the shutup callback currently used for ALC269-variant. This patch addresses these noise issues by introducing a new fixup chain. Although the same workaround might be applicable to other Thinkpad models, it's applied only to T440s (17aa:220c) in this patch, so far, just to be safe (you chicken!). As a compromise, a new model option string "tp440" is provided now, though, so that owners of other Thinkpad models can test it more easily. Bugzilla: https://bugzilla.opensuse.org/show_bug.cgi?id=958504Reported-and-tested-by:
Tim Hardeck <thardeck@suse.de> Signed-off-by:
-
Jason A. Donenfeld authored
commit 70d906bc upstream. Some ciphers actually support encrypting zero length plaintexts. For example, many AEAD modes support this. The resulting ciphertext for those winds up being only the authentication tag, which is a result of the key, the iv, the additional data, and the fact that the plaintext had zero length. The blkcipher constructors won't copy the IV to the right place, however, when using a zero length input, resulting in some significant problems when ciphers call their initialization routines, only to find that the ->iv parameter is uninitialized. One such example of this would be using chacha20poly1305 with a zero length input, which then calls chacha20, which calls the key setup routine, which eventually OOPSes due to the uninitialized ->iv member. Signed-off-by:
Jason A. Donenfeld <Jason@zx2c4.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Wang Dongsheng authored
commit acfc1cc1 upstream. If diu_ops is not implemented on platform, kernel will access a NULL pointer. We need to check this pointer in DIU initialization. Signed-off-by:
Wang Dongsheng <dongsheng.wang@freescale.com> Acked-by:
Timur Tabi <timur@tabi.org> Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by:
-
- 19 Jan, 2016 8 commits
-
-
Oded Gabbay authored
commit 361c32d3 upstream. This patch makes the VCE IB test pass on Big-Endian systems. It converts to little-endian the contents of the VCE message. Reviewed-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
Oded Gabbay <oded.gabbay@gmail.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Oded Gabbay authored
commit 687f4b98 upstream. This patch fixes the VCE ring test when running on Big-Endian machines. Every write to the ring needs to be translated to little-endian. Reviewed-by:
-
Oded Gabbay authored
commit 5f3e226f upstream. This patch makes the IB test on the GFX ring pass for CI-based cards installed in Big-Endian machines. Reviewed-by:
-
Al Viro authored
commit 4ad78628 upstream. For block devices the pagecache is associated with the inode on bdevfs, not with the aliasing ones on the mountable filesystems. The latter have its own ->i_data empty and ->i_mapping pointing to the (unique per major/minor) bdevfs inode. That guarantees cache coherence between all block device inodes with the same device number. Eviction of an alias inode has no business trying to evict the pages belonging to bdevfs one; moreover, ->i_mapping is only safe to access when the thing is opened. At the time of ->evict_inode() the victim is definitely *not* opened. We are about to kill the address space embedded into struct inode (inode->i_data) and that's what we need to empty of any pages. 9p instance tries to empty inode->i_mapping instead, which is both unsafe and bogus - if we have several device nodes with the same device number in different places, closing one of them should not try to empty the (shared) page cache. Fortunately, other instances in the tree are OK; they are evicting from &inode->i_data instead, as 9p one should. Reported-by:
"Suzuki K. Poulose" <Suzuki.Poulose@arm.com> Tested-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
-
Hui Wang authored
commit 23adc192 upstream. We have two latest thinkpad laptop models which are all based on the Intel skylake platforms, and all of them have the codec alc293 on them. When the machines boot to the desktop, an greeting dialogue shows up with the notification sound. But on these two models, there is noise with the notification sound. We have 3 SKUs for each of the models, all of them have this problem. So far, this problem is only specific to these two thinkpad models, we did not find this problem on the old thinkpad models with the codec alc293 or alc292. A workaround for this problem is disabling the aamix. BugLink: https://bugs.launchpad.net/bugs/1523517Signed-off-by:
Hui Wang <hui.wang@canonical.com> Signed-off-by:
-
Sagi Grimberg authored
commit 09c0c0be upstream. When using work request based memory registration (fast_reg) we must reserve SQ entries for registration and invalidation in addition to send operations. Each IO consumes 3 SQ entries (registration, send, invalidation) so we need to allocate 3x larger send-queue instead of 2x. Signed-off-by:
Sagi Grimberg <sagig@mellanox.com> Reviewed-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
-
Bart Van Assche authored
commit 4d59ad29 upstream. If srp_connect_ch() returns a positive value then that is considered by its caller as a connection failure but this does not result in a scsi_host_put() call and additionally causes the srp_create_target() function to return a positive value while it should return a negative value. Avoid all this confusion and additionally fix a memory leak by ensuring that srp_connect_ch() always returns a value that is <= 0. This patch avoids that a rejected login triggers the following memory leak: unreferenced object 0xffff88021b24a220 (size 8): comm "srp_daemon", pid 56421, jiffies 4295006762 (age 4240.750s) hex dump (first 8 bytes): 68 6f 73 74 35 38 00 a5 host58.. backtrace: [<ffffffff8151014a>] kmemleak_alloc+0x7a/0xc0 [<ffffffff81165c1e>] __kmalloc_track_caller+0xfe/0x160 [<ffffffff81260d2b>] kvasprintf+0x5b/0x90 [<ffffffff81260e2d>] kvasprintf_const+0x8d/0xb0 [<ffffffff81254b0c>] kobject_set_name_vargs+0x3c/0xa0 [<ffffffff81337e3c>] dev_set_name+0x3c/0x40 [<ffffffff81355757>] scsi_host_alloc+0x327/0x4b0 [<ffffffffa03edc8e>] srp_create_target+0x4e/0x8a0 [ib_srp] [<ffffffff8133778b>] dev_attr_store+0x1b/0x20 [<ffffffff811f27fa>] sysfs_kf_write+0x4a/0x60 [<ffffffff811f1e8e>] kernfs_fop_write+0x14e/0x180 [<ffffffff81176eef>] __vfs_write+0x2f/0xf0 [<ffffffff811771e4>] vfs_write+0xa4/0x100 [<ffffffff81177c64>] SyS_write+0x54/0xc0 [<ffffffff8151b257>] entry_SYSCALL_64_fastpath+0x12/0x6f Signed-off-by:
Bart Van Assche <bart.vanassche@sandisk.com> Reviewed-by:
-
Suman Anna authored
commit c13f99b7 upstream. The virtio core uses a static ida named virtio_index_ida for assigning index numbers to virtio devices during registration. The ida core may allocate some internal idr cache layers and an ida bitmap upon any ida allocation, and all these layers are truely freed only upon the ida destruction. The virtio_index_ida is not destroyed at present, leading to a memory leak when using the virtio core as a module and atleast one virtio device is registered and unregistered. Fix this by invoking ida_destroy() in the virtio core module exit. Signed-off-by:
Suman Anna <s-anna@ti.com> Signed-off-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
-
