- 02 Aug, 2010 40 commits
-
-
Mauro Carvalho Chehab authored
Rewrites the siano IR implementation. The previous implementation were non-standard. As such, it has issues if more than one device registers IR, as there used to have some static constants used during protocol decoding phase. Also, it used to implement its on RAW decoder, and only for RC5. The new code uses RC core subsystem for handling IR. This brings several new features to the driver, including: - Allow to dynamically replace the IR keycodes; - Supports all existing raw decoders (JVC, NEC, RC-5, RC-6, SONY); - Supports lirc dev; - Doesn't have race conditions when more than one sms IR is registered; - The code size for the IR implementation is very small; - it exports the IR features via /sys/class/rc. Signed-off-by:Mauro Carvalho Chehab <mchehab@redhat.com>
-
Mauro Carvalho Chehab authored
sms were using a non-compliant nomenclature for the USB devices. Fix it. Signed-off-by: -
Mauro Carvalho Chehab authored
Use a more standard way to name those tables, as they're currently used by the script that coverts those tables to be loaded via userspace. Signed-off-by: -
Mauro Carvalho Chehab authored
Add the proper gpio port for WinTV MiniStick, with the information provided by Michael. Thanks-to: Michael Krufky <mkrufky@kernellabs.com> Signed-off-by: -
Mauro Carvalho Chehab authored
Simplifies the logic for handling firmware 1.20 RC messages, fixing the logic. While here, I tried to use a RC-6 remote controller from my TV set, but it didn't work with dib0700. Not sure why, but maybe this never worked. Signed-off-by: -
Mauro Carvalho Chehab authored
This patch implements change_protocol callback. With this change, there's no need for an extra modprobe parameter to specify the protocol. When a table is loaded (either from in-kernel rc-map tables or via ir-keytable program), the driver will automatically change the protocol, in order to work with the given table. Signed-off-by: -
Mauro Carvalho Chehab authored
Instead of having one big keytable with 2 protocols inside, break it into two separate tables, being one for NEC and another for RC-5 variants, and properly identify what variant should be used at the boards entries. Signed-off-by: -
Mauro Carvalho Chehab authored
a 250ms delay is too low for this device. It ends by producing false repeat events. Increase the delay time to 500 ms to avoid troubles. Signed-off-by: -
Mauro Carvalho Chehab authored
Use the new rc-core handler at dvb-usb-remote for dib0700 driver. Signed-off-by: -
Mauro Carvalho Chehab authored
Signed-off-by: -
Mauro Carvalho Chehab authored
Allows dvb-usb drivers to use rc-core, instead of the legacy implementation. No driver were ported yet to rc-core, so, some small adjustments may be needed, when starting to migrate the drivers. Signed-off-by: -
Mauro Carvalho Chehab authored
This is a big patch, yet trivial. It just move the RC properties to a separate struct, in order to prepare the dvb-usb drivers to use rc-core. There's no change on the behavior of the drivers. With this change, it is possible to have both legacy and rc-core based code inside the dvb-usb-remote, allowing a gradual migration to rc-core, driver per driver. Signed-off-by: -
Mauro Carvalho Chehab authored
dvb-usb has its own IR handle code. Now that we have a Remote Controller subsystem, we should start using it. So, remove this struct, in favor of the similar struct defined at the RC subsystem. This is a big, but trivial patch. It is a 3 line delect, plus lots of rename on several dvb-usb files. Signed-off-by: -
Guennadi Liakhovetski authored
RJ54N1CB0C is a Sharp camera sensor. Signed-off-by:
Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by:
-
Guennadi Liakhovetski authored
SH7724 datasheet specifies 480 pixels as the VOU maximum vertical resolution. This is a bug in the datasheet, VOU also supports the full PAL resolution: 576 lines. Adjust the driver accordingly. Signed-off-by:
-
Guennadi Liakhovetski authored
Using CEU with CSI2 on SH-Mobile requires some special configuration of the former. We also have to switch from calling only one subdev .s_mbus_fmt and .try_mbus_fmt to calling all subdevices. Take care to increment CSI2 driver use count to prevent it from unloading, while in use. Signed-off-by:
-
Guennadi Liakhovetski authored
Some SH-Mobile SoCs implement a MIPI CSI-2 controller, that can interface to several video clients and send data to the CEU or to the Image Signal Processor. This patch implements a v4l2-subdevice driver for CSI-2 to be used within the soc-camera framework, implementing the second subdevice in addition to the actual video clients. Signed-off-by:
-
Guennadi Liakhovetski authored
Signed-off-by:
-
Guennadi Liakhovetski authored
These formats belong to the standard format set, defined by the MIPI CSI-2 specification. Signed-off-by:
-
Guennadi Liakhovetski authored
Endianness notation is meaningless for 8 bit YUYV codes. Switch pixel code names to explicitly state the order of colour components in the data stream. Signed-off-by:
-
Mauro Carvalho Chehab authored
Signed-off-by: -
Jarod Wilson authored
Make the bits under staging/lirc/ buildable, and add a TODO note. Signed-off-by:
Jarod Wilson <jarod@redhat.com> Signed-off-by:
-
Jarod Wilson authored
Commonly found on several Hauppauge video capture devices. Signed-off-by:
-
Jarod Wilson authored
Signed-off-by:
-
Jarod Wilson authored
Signed-off-by:
-
Jarod Wilson authored
Signed-off-by:
-
Jarod Wilson authored
Signed-off-by:
-
Jarod Wilson authored
Signed-off-by:
-
Jarod Wilson authored
Signed-off-by:
-
Jarod Wilson authored
Signed-off-by:
-
Jarod Wilson authored
Signed-off-by:
-
Jarod Wilson authored
Nb: this is a very trimmed-down lirc_imon, which only supports the oldest generation of imon devices that don't do onboard signal decoding like the most recent generation imon devices -- those are now supported by the ir-core imon driver. Signed-off-by:
-
Jarod Wilson authored
Signed-off-by:
-
Mauro Carvalho Chehab authored
Signed-off-by: -
Jarod Wilson authored
Signed-off-by:
-
Jarod Wilson authored
[mchehab@redhat.com: fixed a few WARNING: please, no space before tabs] Signed-off-by:
-
Jarod Wilson authored
Signed-off-by:
-
Michael Krufky authored
Signed-off-by:
Michael Krufky <mkrufky@kernellabs.com> Acked-by:
Luca Olivetti <luca@ventoso.org> Signed-off-by:
-
Jarod Wilson authored
This adds support for the KWorld PlusTV 340U and KWorld UB345-Q ATSC sticks, which are really the same device. The sticks have an eMPIA em2870 usb bridge chipset, an LG Electronics LGDT3304 ATSC/QAM demodulator and an NXP TDA18271HD tuner -- early versions of the 340U have a a TDA18271HD/C1, later models and the UB435-Q have a C2. The stick has been tested succesfully with both VSB_8 and QAM_256 signals. Its using lgdt3304 support added to the lgdt3305 driver by a prior patch, rather than the current lgdt3304 driver, as its severely lacking in functionality by comparison (see said patch for details). Signed-off-by:
-
Jiri Slaby authored
In dvb_dvr_release, there is a test dvbdev->users==-1, but users are never negative. This error results in hung tasks: task PC stack pid father bash D ffffffffa000c948 0 3264 3170 0x00000000 ffff88003aec5ce8 0000000000000086 0000000000011f80 0000000000011f80 ffff88003aec5fd8 ffff88003aec5fd8 ffff88003b848670 0000000000011f80 ffff88003aec5fd8 0000000000011f80 ffff88003e02a030 ffff88003b848670 Call Trace: [<ffffffff813dd4a5>] dvb_dmxdev_release+0xc5/0x130 [<ffffffff8107b750>] ? autoremove_wake_function+0x0/0x40 [<ffffffffa00013a2>] dvb_usb_adapter_dvb_exit+0x42/0x70 [dvb_usb] [<ffffffffa0000525>] dvb_usb_exit+0x55/0xd0 [dvb_usb] [<ffffffffa00005ee>] dvb_usb_device_exit+0x4e/0x70 [dvb_usb] [<ffffffffa000a065>] af9015_usb_device_exit+0x55/0x60 [dvb_usb_af9015] [<ffffffff813a3f05>] usb_unbind_interface+0x55/0x1a0 [<ffffffff81316000>] __device_release_driver+0x70/0xe0 ... So check against 1 there instead. BTW why's the TODO there? Adding TODOs to the code without descriptions is like adding nothing. Signed-off-by:
Jiri Slaby <jslaby@suse.cz> Signed-off-by:
-
