This patch fixes build error when SMSC_TRACE() used.
Signed-off-by: Jeongtae Park <jtp.park@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit e9a799ea (xen: netfront: ethtool stats fields should be
unsigned long) made rx_gso_checksum_fixup an unsigned long.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the lower device has offloading capabilities, the packets checksums
are not computed. That leads to have any macvlan port in bridge mode to
not work because the packets are dropped due to a bad checksum.

If the macvlan is in bridge mode, the packet is forwarded to another
macvlan port and reach the network stack where it looks for a checksum
but this one was not computed due to the offloading of the lower device.
In this case, we have to set the packet with CHECKSUM_UNNECESSARY
when it is forwarded to a bridged port and restore the previous value of
ip_summed when the packet goes to the lowerdev.
Signed-off-by: Daniel Lezcano <daniel.lezcano@free.fr>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Andrian Nord <nightnord@gmail.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

HyStart sets the initial exit point of slow start.
Suppose that HyStart exits at 0.5BDP in a BDP network and no history exists.
If the BDP of a network is large, CUBIC's initial cwnd growth may be
too conservative to utilize the link.
CUBIC increases the cwnd 20% per RTT in this case.
Signed-off-by: Sangtae Ha <sangtae.ha@gmail.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make HyStart less sensitive to abrupt delay variations due to buffer bloat.
Signed-off-by: Sangtae Ha <sangtae.ha@gmail.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Reported-by: Lucas Nussbaum <lucas.nussbaum@loria.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a refined version of an earlier patch by Lucas Nussbaum.
Cubic needs RTT values in milliseconds. If HZ < 1000 then
the values will be too coarse.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Reported-by: Lucas Nussbaum <lucas.nussbaum@loria.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

The hystart code was written with assumption that HZ=1000.
Replace the use of jiffies with bictcp_clock as a millisecond
real time clock.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Reported-by: Lucas Nussbaum <lucas.nussbaum@loria.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make the spacing between ACK's that indicates a train a tuneable
value like other hystart values.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiffies wraps around therefore the correct way to compare is
to use cast to signed value.

Note: cubic is not using full jiffies value on 64 bit arch
because using full unsigned long makes struct bictcp grow too
large for the available ca_priv area.

Includes correction from Sangtae Ha to improve ack train detection.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the congestion control interface, the callback for each ACK
includes an estimated round trip time in microseconds.
Some algorithms need high resolution (Vegas style) but most only
need jiffie resolution.  If RTT is not accurate (like a retransmission)
-1 is used as a flag value.

When doing coarse resolution if RTT is less than a a jiffie
then 0 should be returned rather than no estimate. Otherwise algorithms
that expect good ack's to trigger slow start (like CUBIC Hystart)
will be confused.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit a6c36ee6 ("bonding: change list
contact to netdev@vger.kernel.org"), the mailing list for bonding
developpement was changed from bonding-devel to netdev.

Update the bonding documentation to reflect this change:

- bonding-devel is used for usage discussions (despite the name).
- netdev is used for developpement discussions.

Also remove the reference to the sourceforge bonding page, which is
deprecated.
Signed-off-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

We latch our state using a spinlock not a r/w kind of lock.
Signed-off-by: Daniel Baluta <dbaluta@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, for N 5800 XM I get:
cdc_phonet: probe of 1-6:1.10 failed with error -22

It's because phonet_header is empty. Extra altsetting looks like
there:
E 05 24 00 01 10 03 24 ab 05 24 06 0a 0b 04 24 fd  .$....$..$....$.
E 00                                               .

I don't see the header used anywhere so just check if the phonet
descriptor is there, not the structure itself.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Cc: David S. Miller <davem@davemloft.net>
Acked-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently there is a warning emitted by the cdc-phonet driver:
WARNING: at include/linux/netdevice.h:1557 usbpn_probe+0x3bb/0x3f0 [cdc_phonet]()
Modules linked in: ...
Pid: 5877, comm: insmod Not tainted 2.6.37.3-16-desktop #1
Call Trace:
 [<ffffffff810059b9>] dump_trace+0x79/0x340
 [<ffffffff81520fdc>] dump_stack+0x69/0x6f
 [<ffffffff810580eb>] warn_slowpath_common+0x7b/0xc0
 [<ffffffffa00254fb>] usbpn_probe+0x3bb/0x3f0 [cdc_phonet]
...
---[ end trace f5d3e02908603ab4 ]---
netif_stop_queue() cannot be called before register_netdev()

So remove netif_stop_queue from the probe funtction to avoid that.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Cc: David S. Miller <davem@davemloft.net>
Acked-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixup the rx_gso_checksum_fixup field added in e0ce4af9 to be
unsigned long as suggested by Ben Hutchings in
<1298919198.2569.14.camel@bwh-desktop>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If Spanning Tree Protocol is not enabled, there is no good reason for
the bridge code to wait for the forwarding delay period before enabling
the link. The purpose of the forwarding delay is to allow STP to
learn about other bridges before nominating itself.

The only possible impact is that when starting up a new port
the bridge may flood a packet now, where previously it might have
seen traffic from the other host and preseeded the forwarding table.

Includes change for local variable br already available in that func.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Don't reset tx_fifo_errors when reading out current EMAC stats.
  (tx_fifo_errors shows up as TX overruns in netdev stats.)

Without this correction, the old counter value is lost every time
stats are read out.
Signed-off-by: Thomas Lange <thomas@corelatus.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

Index i was already used in the outer loop.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simply remove redundant 'dev' NULL check.
Signed-off-by: Jinqiu Yang <crindy646@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add necessary alias to autoload ip6ip6 tunnel module.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When configs BRIDGE=y and IPV6=m, this build error occurs:

br_multicast.c:(.text+0xa3341): undefined reference to `ipv6_dev_get_saddr'

BRIDGE_IGMP_SNOOPING is boolean; if it were tristate, then adding
	depends on IPV6 || IPV6=n
to BRIDGE_IGMP_SNOOPING would be a good fix.  As it is currently,
making BRIDGE depend on the IPV6 config works.
Reported-by: Patrick Schaaf <netdev@bof.de>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* 'media_fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
  [media] mantis_pci: remove asm/pgtable.h include
  [media] tda829x: fix regression in probe functions
  [media] mceusb: don't claim multifunction device non-IR parts
  [media] nuvoton-cir: fix wake from suspend
  [media] cx18: Add support for Hauppauge HVR-1600 models with s5h1411
  [media] ivtv: Fix corrective action taken upon DMA ERR interrupt to avoid hang
  [media] cx25840: fix probing of cx2583x chips
  [media] cx23885: Remove unused 'err:' labels to quiet compiler warning
  [media] cx23885: Revert "Check for slave nack on all transactions"
  [media] DiB7000M: add pid filtering
  [media] Fix sysfs rc protocol lookup for rc-5-sz
  [media] au0828: fix VBI handling when in V4L2 streaming mode
  [media] ir-raw: Properly initialize the IR event (BZ#27202)
  [media] s2255drv: firmware re-loading changes
  [media] Fix double free of video_device in mem2mem_testdev
  [media] DM04/QQBOX memcpy to const char fix

This patch fixes an issue in OpenIPMI module where sometimes an ABORT command
is sent after sending an IPMI request to BMC causing the IPMI request to fail.
Signed-off-by: YiCheng Doe <yicheng.doe@hp.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Acked-by: Tom Mingarelli <thomas.mingarelli@hp.com>
Tested-by: Andy Cress <andy.cress@us.kontron.com>
Tested-by: Mika Lansirine <Mika.Lansirinne@stonesoft.com>
Tested-by: Brian De Wolf <bldewolf@csupomona.edu>
Cc: Jean Michel Audet <Jean-Michel.Audet@ca.Kontron.com>
Cc: Jozef Sudelsky <jozef.sudolsky@elbiahosting.sk>
Acked-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
  fs/dcache: allow d_obtain_alias() to return unhashed dentries
  Check for immutable/append flag in fallocate path
  sysctl: the include of rcupdate.h is only needed in the kernel
  fat: fix d_revalidate oopsen on NFS exports
  jfs: fix d_revalidate oopsen on NFS exports
  ocfs2: fix d_revalidate oopsen on NFS exports
  gfs2: fix d_revalidate oopsen on NFS exports
  fuse: fix d_revalidate oopsen on NFS exports
  ceph: fix d_revalidate oopsen on NFS exports
  reiserfs xattr ->d_revalidate() shouldn't care about RCU
  /proc/self is never going to be invalidated...

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86, UV: Initialize the broadcast assist unit base destination node id properly
  x86, numa: Fix numa_emulation code with memory-less node0
  x86, build: Make sure mkpiggy fails on read error

Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  sched: Fix sched rt group scheduling when hierachy is enabled

* 'perf/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  perf symbols: Avoid resolving [kernel.kallsyms] to real path for buildid cache
  perf symbols: Fix vmlinux path when not using --symfs

This reverts commit 951f3512

    drm/i915: Do not handle backlight combination mode specially

since this commit introduced other regressions due to untouched LBPC
register, e.g. the backlight dimmed after resume.

In addition to the revert, this patch includes a fix for the original
issue (weird backlight levels) by removing the wrong bit shift for
computing the current backlight level.
Also, including typo fixes (lpbc -> lbpc).

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=34524Acked-by: Indan Zupancic <indan@nul.nu>
Reviewed-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Without this patch, inodes are not promptly freed on last close of an
unlinked file by an nfs client:

	client$ mount -tnfs4 server:/export/ /mnt/
	client$ tail -f /mnt/FOO
	...
	server$ df -i /export
	server$ rm /export/FOO
	(^C the tail -f)
	server$ df -i /export
	server$ echo 2 >/proc/sys/vm/drop_caches
	server$ df -i /export

the df's will show that the inode is not freed on the filesystem until
the last step, when it could have been freed after killing the client's
tail -f. On-disk data won't be deallocated either, leading to possible
spurious ENOSPC.

This occurs because when the client does the close, it arrives in a
compound with a putfh and a close, processed like:

	- putfh: look up the filehandle.  The only alias found for the
	  inode will be DCACHE_UNHASHED alias referenced by the filp
	  this, so it creates a new DCACHE_DISCONECTED dentry and
	  returns that instead.
	- close: closes the existing filp, which is destroyed
	  immediately by dput() since it's DCACHE_UNHASHED.
	- end of the compound: release the reference
	  to the current filehandle, and dput() the new
	  DCACHE_DISCONECTED dentry, which gets put on the
	  unused list instead of being destroyed immediately.

Nick Piggin suggested fixing this by allowing d_obtain_alias to return
the unhashed dentry that is referenced by the filp, instead of making it
create a new dentry.

Leave __d_find_alias() alone to avoid changing behavior of other
callers.

Also nfsd doesn't need all the checks of __d_find_alias(); any dentry,
hashed or unhashed, disconnected or not, should work.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

In the fallocate path the kernel doesn't check for the immutable/append
flag. It's possible to have a race condition in this scenario: an
application open a file in read/write and it does something, meanwhile
root set the immutable flag on the file, the application at that point
can call fallocate with success. In addition, we don't allow to do any
unreserve operation on an append only file but only the reserve one.
Signed-off-by: Marco Stornelli <marco.stornelli@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Fixes this built error:

include/linux/sysctl.h:28: included file 'linux/rcupdate.h' is not exported
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

can't blindly check nd->flags in ->d_revalidate()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

can't blindly check nd->flags in ->d_revalidate()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

can't blindly check nd->flags in ->d_revalidate()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

can't blindly check nd->flags in ->d_revalidate()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

can't blindly check nd->flags in ->d_revalidate()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

can't blindly check nd->flags in ->d_revalidate()
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

... it returns an error unconditionally
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>