udp_poll() can in some circumstances drop frames with incorrect checksums.

Problem is we now have to lock the socket while dropping frames, or risk
sk_forward corruption.

This bug is present since commit 95766fff
([UDP]: Add memory accounting.)

While we are at it, we can correct ioctl(SIOCINQ) to also drop bad frames.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cisco HDLC uses keepalive packets and sequence numbers to determine link
state. In rare cases both ends could transmit keepalive packets at the same
time, causing the received sequence numbers to be treated as incorrect.
Now we accept our current sequence number as well as the previous one.
Signed-off-by: Krzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

I was trying to use TCP_DEFER_ACCEPT and noticed that if the
client does not talk, the connection is never accepted and
remains in SYN_RECV state until the retransmits expire, where
it finally is deleted. This is bad when some firewall such as
netfilter sits between the client and the server because the
firewall sees the connection in ESTABLISHED state while the
server will finally silently drop it without sending an RST.

This behaviour contradicts the man page which says it should
wait only for some time :

       TCP_DEFER_ACCEPT (since Linux 2.4)
          Allows a listener to be awakened only when data arrives
          on the socket.  Takes an integer value  (seconds), this
          can  bound  the  maximum  number  of attempts TCP will
          make to complete the connection. This option should not
          be used in code intended to be portable.

Also, looking at ipv4/tcp.c, a retransmit counter is correctly
computed :

        case TCP_DEFER_ACCEPT:
                icsk->icsk_accept_queue.rskq_defer_accept = 0;
                if (val > 0) {
                        /* Translate value in seconds to number of
                         * retransmits */
                        while (icsk->icsk_accept_queue.rskq_defer_accept < 32 &&
                               val > ((TCP_TIMEOUT_INIT / HZ) <<
                                       icsk->icsk_accept_queue.rskq_defer_accept))
                                icsk->icsk_accept_queue.rskq_defer_accept++;
                        icsk->icsk_accept_queue.rskq_defer_accept++;
                }
                break;

==> rskq_defer_accept is used as a counter of retransmits.

But in tcp_minisocks.c, this counter is only checked. And in
fact, I have found no location which updates it. So I think
that what was intended was to decrease it in tcp_minisocks
whenever it is checked, which the trivial patch below does.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>

3c574_cs:
 spin_lock the set_multicast_list function.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Belkin F8T012xx1 bluetooth adaptor has the same vendor and product
IDs as the Belkin F5D5050, so we need to teach the pegasus driver to
ignore adaptors belonging to the "Wireless" class 0xE0. For this one
case anyway, seeing as pegasus is a driver for "Wired" adaptors.
Signed-off-by: Chris Rankin <rankincj@yahoo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use resource_size_t for PCI resource remapping instead
of unsigned long. Physical addresses can exceed range of
long data type (e.g with PAE).
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethoc.c: In function ‘ethoc_open’:
drivers/net/ethoc.c:667: warning: comparison of distinct pointer types
lacks a cast
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/wireless/libertas/cmdresp.c: In function ‘lbs_process_event’:
drivers/net/wireless/libertas/cmdresp.c:519: error: ‘TASK_INTERRUPTIBLE’
undeclared (first use in this function)
drivers/net/wireless/libertas/cmdresp.c:519: error: (Each undeclared
identifier is reported only once
drivers/net/wireless/libertas/cmdresp.c:519: error: for each function it
appears in.)
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ethernet NIC driver for VMware's vmxnet3

From: Shreyas Bhatewara <sbhatewara@vmware.com>

This patch adds driver support for VMware's virtual Ethernet NIC: vmxnet3
Guests running on VMware hypervisors supporting vmxnet3 device will thus have
access to improved network functionalities and performance.
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: Ronghua Zhang <ronghua@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The IXP 2000 network driver was failing to build as it has its own
statistics gathering which was not compatible with the recent network
device operations changes. This patch fixes the driver in the obvious
way and has been compile tested. I have been unable to get the ixp2000
maintainer to comment or test this fix.
Signed-off-by: Vincent Sanders <vince@simtec.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

If ace_load_firmware() fails, ace_init() cleans up but still returns
0, leading to an oops as seen in <http://bugs.debian.org/521383>.
It should pass the error code up.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit a98b65a3 (net: annotate struct sock bitfield), we lost
8 bytes in struct sock on 64bit arches because of
kmemcheck_bitfield_end(flags) misplacement.

Fix this by putting together sk_shutdown, sk_no_check, sk_userlocks,
sk_protocol and sk_type in the 'flags' 32bits bitfield
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This probably deserves to go into -stable.

Pedit will reject a policy that is large because it
uses the wrong structure in the policy validation.
This fixes it.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: David S. Miller <davem@davemloft.net>

We need PHY drivers to initialize in a static kernel before
the MAC drivers that use them.  So link them in first.

Based upon a report by Felix Radensky.
Signed-off-by: David S. Miller <davem@davemloft.net>

Some of the EMAC V4 implementations support 16K Tx FIFOs. This
patch adds support for this functionality and fixes typos in the
Tx FIFO size error messages.
Signed-off-by: Dave Mitchell <dmitchell@appliedmicro.com>
Acked-by: Prodyut Hazarika <phazarika@appliedmicro.com>
Acked-by: Victor Gallardo <vgallardo@appliedmicro.com>
Acked-by: Loc Ho <lho@appliedmicro.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This was accidentally omitted from one of the previous patches for firmware event
handling.  The handler needs to the enable firmware irq mask when it's done
processing or it may not get any more events interrupts.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Call set_multi API after reset recovery.  This was exposed by tripping
tx_timeout.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add wait for NIC fifo and MGMNT fifo to empty before applying reset.
Otherwise broken frames can be processed by management processor and
cause it to hang.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The addresses were being added to the filter properly, but were not
being enabled.  This adds enable bit to filter write.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Broadcast/multicast should always be routed to the default (zeroeth) rx
ring.  Broadcast frames are already routed correctly.  This fixes
routing for multicast frames.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently frames are routed based on their type and MAC address. This
patch adds the port number on which the frame arrived to the routing.
This prevents problems in the case where both interfaces have the same MAC address in
a routing configuration.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix RX queue table size and change from random to default hash values.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The error unwinding code in set_netns has a bug
that will make it run into a BUG_ON if passed a
bad wiphy index, fix by not trying to unlock a
wiphy that doesn't exist.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Commit 9ef1d4c7 ("[NETLINK]: Missing
initializations in dumped data") introduced a typo in
initialization. This patch fixes this.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It's not necessary and it's illegal too.
Reported-by: Alexander Strakh <strakh@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

nanodoc was missing an ndo_-prefix.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The DMA-API debugging facility complains about b43 mapping memory from
stack for SDIO-based cards.

Indeed, b43 currently allocates the PIO RX/TX header and tail buffers
from stack. The solution here is to use heap-allocated buffers instead.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In Bugzilla No. 14181, a PowerMac G4 crashes on ifdown or
module unload because the rfkill polling has not been stopped.
For the x86 architectures, the attempt to reach a now unmapped
register is not fatal as it is on PPC.

(Includes "b43: Fix locking problem when stopping rfkill polling". -- JWL)
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

kfree_skb() should be used to free struct sk_buff pointers.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

A logical of shifts to the left doesn't make sense.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

User-visible messages should use formatted MAC addresses ("00:01:...")
rather than raw ("0001...") so they match other parts of the system.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
CC: ilw@linux.intel.com
CC: linux-wireless@vger.kernel.org
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix IRQ mask sanity check for physically pulled device.
Tested-by: Andrew Price <andy@andrewprice.me.uk>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The return type of abs() was recently changed from int to long. With
min()'s type checking we thus need to make sure that values of the same
type are compared.

This fixes:

    CC [M]  drivers/net/wireless/iwlwifi/iwl-5000.o
drivers/net/wireless/iwlwifi/iwl-5000.c: In function ‘iwl5000_gain_computation’:
drivers/net/wireless/iwlwifi/iwl-5000.c:320: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reported-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fixes following on big endian systems:
  CC [M]  drivers/net/wireless/iwlwifi/iwl-rx.o
  drivers/net/wireless/iwlwifi/iwl-rx.c: In function ‘iwl_rx_reply_rx’:
  drivers/net/wireless/iwlwifi/iwl-rx.c:1029: warning: integer overflow in
  expression
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Reported-by: Marcel Holtmann <marcel@holtmann.org>
Tested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Set the correct EEPROM offset for enhance tx power for 6000 series
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The address stored in the next link address is a word address but when
reading the OTP blocks, a byte address is used. Also if the blocks are
full and the last link pointer is not zero, then none of the blocks are
valid so return an error.

The algorithm is simply valid blocks have a next address and that
address's contents is zero.

Using the wrong address for the next link address gets arbitrary data,
obviously. In cases seen, the first block is considered valid when it is not.

If the block has in fact been invalidated there may be old data or
there may be no data, bad data, or partial data, there is no way of
telling. Without this patch it is possible that a device with valid OTP data
is unable to work.
Signed-off-by: Jay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When receiving data frames, we can send them only to
the interface they belong to based on transmitting
station (this doesn't work for probe requests). Also,
don't try to handle other frames for AP_VLAN at all
since those interface should only receive data.

Additionally, the transmit side must check that the
station we're sending a frame to is actually on the
interface we're transmitting on, and not transmit
packets to functions that live on other interfaces,
so validate that as well.

Another bug fix is needed in sta_info.c where in the
VLAN case when adding/removing stations we overwrite
the sdata variable we still need.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Don't use struct wldev after detach. This fixes an oops on access.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>