[ Upstream commit 6d6b0d0d ]

When in slave mode, an arbitration loss (ARLO) may be detected before the
slave had a chance to detect the stop condition (STOPF in ISR).
This is seen when two master + slave adapters switch their roles. It
provokes the i2c bus to be stuck, busy as SCL line is stretched.
- the I2C_SLAVE_STOP event is never generated due to STOPF flag is set but
  don't generate an irq (race with ARLO irq, STOPIE is masked). STOPF flag
  remains set until next master xfer (e.g. when STOPIE irq get unmasked).
  In this case, completion is generated too early: immediately upon new
  transfer request (then it doesn't send all data).
- Some data get stuck in TXDR register. As a consequence, the controller
  stretches the SCL line: the bus gets busy until a future master transfer
  triggers the bus busy / recovery mechanism (this can take time... and
  may never happen at all)

So choice is to let the STOPF being detected by the slave isr handler,
to properly handle this stop condition. E.g. don't mask IRQs in error
handler, when the slave is running.

Fixes: 60d609f3 ("i2c: i2c-stm32f7: Add slave support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 02e64276 ]

The slave-interface documentation [1] states "the bus driver should
transmit the first byte" upon I2C_SLAVE_READ_REQUESTED slave event:
- 'val': backend returns first byte to be sent
The driver currently ignores the 1st byte to send on this event.

[1] https://www.kernel.org/doc/Documentation/i2c/slave-interface

Fixes: 60d609f3 ("i2c: i2c-stm32f7: Add slave support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@st.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 84243125 ]

On a system without Single VMOVP support (say GITS_TYPER.VMOVP == 0),
we will map vPEs only on ITSs that will actually control interrupts
for the given VM.  And when moving a vPE, the VMOVP command will be
issued only for those ITSs.

But when issuing VMOVPs we seemed fail to present the exact ITSList
to ITSs who are actually included in the synchronization operation.
The its_list_map we're currently using includes all ITSs in the system,
even though some of them don't have the corresponding vPE mapping at all.

Introduce get_its_list() to get the per-VM its_list_map, to indicate
which ITSs have vPE mappings for the given VM, and use this map as
the expected ITSList when building VMOVP. This is hopefully a performance
gain not to do some synchronization with those unsuspecting ITSs.
And initialize the whole command descriptor to zero at beginning, since
the seq_num and its_list should be RES0 when GITS_TYPER.VMOVP == 1.
Signed-off-by: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1571802386-2680-1-git-send-email-yuzenghui@huawei.comSigned-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit e4f5cb1a ]

The vectors span more than one byte, so mark them as arrays.

Fixes the following build error when building when using GCC 8.3:

In file included from ./include/linux/string.h:19,
                 from ./include/linux/bitmap.h:9,
                 from ./include/linux/cpumask.h:12,
                 from ./arch/mips/include/asm/processor.h:15,
                 from ./arch/mips/include/asm/thread_info.h:16,
                 from ./include/linux/thread_info.h:38,
                 from ./include/asm-generic/preempt.h:5,
                 from ./arch/mips/include/generated/asm/preempt.h:1,
                 from ./include/linux/preempt.h:81,
                 from ./include/linux/spinlock.h:51,
                 from ./include/linux/mmzone.h:8,
                 from ./include/linux/bootmem.h:8,
                 from arch/mips/bcm63xx/prom.c:10:
arch/mips/bcm63xx/prom.c: In function 'prom_init':
./arch/mips/include/asm/string.h:162:11: error: '__builtin_memcpy' forming offset [2, 32] is out of the bounds [0, 1] of object 'bmips_smp_movevec' with type 'char' [-Werror=array-bounds]
   __ret = __builtin_memcpy((dst), (src), __len); \
           ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/mips/bcm63xx/prom.c:97:3: note: in expansion of macro 'memcpy'
   memcpy((void *)0xa0000200, &bmips_smp_movevec, 0x20);
   ^~~~~~
In file included from arch/mips/bcm63xx/prom.c:14:
./arch/mips/include/asm/bmips.h:80:13: note: 'bmips_smp_movevec' declared here
 extern char bmips_smp_movevec;

Fixes: 18a1eef9 ("MIPS: BMIPS: Introduce bmips.h")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit e13de8fe ]

In unittest_data_add, a copy buffer is created via kmemdup. This buffer
is leaked if of_fdt_unflatten_tree fails. The release for the
unittest_data buffer is added.

Fixes: b951f9dc ("Enabling OF selftest to run without machine's devicetree")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: Frank Rowand <frowand.list@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 2ecb2879 ]

r0-r3 & r12 registers are saved & restored, before & after svc
respectively. Intention was to preserve those registers across thread to
handler mode switch.

On v7-M, hardware saves the register context upon exception in AAPCS
complaint way. Restoring r0-r3 & r12 is done from stack location where
hardware saves it, not from the location on stack where these registers
were saved.

To clarify, on stm32f429 discovery board:

1. before svc, sp - 0x90009ff8
2. r0-r3,r12 saved to 0x90009ff8 - 0x9000a00b
3. upon svc, h/w decrements sp by 32 & pushes registers onto stack
4. after svc,  sp - 0x90009fd8
5. r0-r3,r12 restored from 0x90009fd8 - 0x90009feb

Above means r0-r3,r12 is not restored from the location where they are
saved, but since hardware pushes the registers onto stack, the registers
are restored correctly.

Note that during register saving to stack (step 2), it goes past
0x9000a000. And it seems, based on objdump, there are global symbols
residing there, and it perhaps can cause issues on a non-XIP Kernel
(on XIP, data section is setup later).

Based on the analysis above, manually saving registers onto stack is at
best no-op and at worst can cause data section corruption. Hence remove
storing of registers onto stack before svc.

Fixes: b70cd406 ("ARM: 8671/1: V7M: Preserve registers across switch from Thread to Handler mode")
Signed-off-by: afzal mohammed <afzal.mohd.ma@gmail.com>
Acked-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 9fa8c9c6 ]

In the format of synthetic events, the "gfp_t" is shown as "signed:1",
but in fact the "gfp_t" is "unsigned", should be shown as "signed:0".

The issue can be reproduced by the following commands:

echo 'memlatency u64 lat; unsigned int order; gfp_t gfp_flags; int migratetype' > /sys/kernel/debug/tracing/synthetic_events
cat  /sys/kernel/debug/tracing/events/synthetic/memlatency/format

name: memlatency
ID: 2233
format:
        field:unsigned short common_type;       offset:0;       size:2; signed:0;
        field:unsigned char common_flags;       offset:2;       size:1; signed:0;
        field:unsigned char common_preempt_count;       offset:3;       size:1; signed:0;
        field:int common_pid;   offset:4;       size:4; signed:1;

        field:u64 lat;  offset:8;       size:8; signed:0;
        field:unsigned int order;       offset:16;      size:4; signed:0;
        field:gfp_t gfp_flags;  offset:24;      size:4; signed:1;
        field:int migratetype;  offset:32;      size:4; signed:1;

print fmt: "lat=%llu, order=%u, gfp_flags=%x, migratetype=%d", REC->lat, REC->order, REC->gfp_flags, REC->migratetype

Link: http://lkml.kernel.org/r/20191018012034.6404-1-zhengjun.xing@linux.intel.comReviewed-by: Tom Zanussi <tom.zanussi@linux.intel.com>
Signed-off-by: Zhengjun Xing <zhengjun.xing@linux.intel.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 27e84243 ]

passthrough_parse_cdb() - used by TCMU and PSCSI - attepts to reset the LUN
field of SCSI-2 CDBs (bits 5,6,7 of byte 1).  The current code is wrong as
for newer commands not having the LUN field it overwrites relevant command
bits (e.g. for SECURITY PROTOCOL IN / OUT). We think this code was
unnecessary from the beginning or at least it is no longer useful. So we
remove it entirely.

Link: https://lore.kernel.org/r/12498eab-76fd-eaad-1316-c2827badb76a@ts.fujitsu.comSigned-off-by: Bodo Stroesser <bstroesser@ts.fujitsu.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 3122051e ]

When we allocate new page tables under memory
pressure we should not evict old ones.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 564b6bb9 ]

dm365 have only single McBSP, so the device name is without .0

Fixes: 0c750e1f ("ARM: davinci: dm365: Add dma_slave_map to edma")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 1abecfca ]

The memory @orig_flags is allocated by strdup(), it is freed on the
normal path, but leak to free on the error path.

Fix this by adding free(orig_flags) on the error path.

Fixes: 0e111156 ("perf kmem: Print gfp flags in human readable string")
Signed-off-by: Yunfeng Ye <yeyunfeng@huawei.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Feilong Lin <linfeilong@huawei.com>
Cc: Hu Shiyuan <hushiyuan@huawei.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/f9e9f458-96f3-4a97-a1d5-9feec2420e07@huawei.comSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit f50b6805 ]

The current checking for failure on the number of ports fails when
-ENODEV is returned from the call to get_num_ports. Fix this by making
num_ports and loop counter i signed rather than unsigned ints. Also
add check for num_ports being less than zero to check for -ve error
returns.

Addresses-Coverity: ("Unsigned compared against 0")
Fixes: e2fea54e ("8250-men-mcb: add support for 16z025 and 16z057")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Michael Moese <mmoese@suse.de>
Link: https://lore.kernel.org/r/20191013220016.9369-1-colin.king@canonical.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit ae199c58 ]

There is a memory leak problem in the failure paths of
build_cl_output(), so fix it.
Signed-off-by: Yunfeng Ye <yeyunfeng@huawei.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Feilong Lin <linfeilong@huawei.com>
Cc: Hu Shiyuan <hushiyuan@huawei.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/4d3c0178-5482-c313-98e1-f82090d2d456@huawei.comSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 252b9e21 ]

i.MX7S/D's GPT ipg clock should be from GPT clock root and
controlled by CCM's GPT CCGR, using correct clock source for
GPT ipg clock instead of IMX7D_CLK_DUMMY.

Fixes: 3ef79ca6 ("ARM: dts: imx7d: use imx7s.dtsi as base device tree")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 8cbf0c17 ]

When building a kernel with SCSI_SNI_53C710 enabled, Kconfig warns:

WARNING: unmet direct dependencies detected for 53C700_LE_ON_BE
  Depends on [n]: SCSI_LOWLEVEL [=y] && SCSI [=y] && SCSI_LASI700 [=n]
  Selected by [y]:
  - SCSI_SNI_53C710 [=y] && SCSI_LOWLEVEL [=y] && SNI_RM [=y] && SCSI [=y]

Add the missing depends SCSI_SNI_53C710 to 53C700_LE_ON_BE to fix it.

Link: https://lore.kernel.org/r/20191009151128.32411-1-tbogendoerfer@suse.deSigned-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 0ee62114 ]

Drop out memory dev_printk() with wrong device pointer argument.

[mkp: typo]

Link: https://lore.kernel.org/r/20191009151118.32350-1-tbogendoerfer@suse.deSigned-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit b6ce6fb1 ]

Some arrays are not capable of returning RTPG data during state
transitioning, but rather return an 'LUN not accessible, asymmetric access
state transition' sense code. In these cases we can set the state to
'transitioning' directly and don't need to evaluate the RTPG data (which we
won't have anyway).

Link: https://lore.kernel.org/r/20191007135701.32389-1-hare@suse.deReviewed-by: Laurence Oberman <loberman@redhat.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 35a79a63 ]

alloc_workqueue is not checked for errors and as a result a potential
NULL dereference could occur.

Link: https://lore.kernel.org/r/1568824618-4366-1-git-send-email-allen.pais@oracle.comSigned-off-by: Allen Pais <allen.pais@oracle.com>
Reviewed-by: Martin Wilck <mwilck@suse.com>
Acked-by: Himanshu Madhani <hmadhani@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 67e15fa5 ]

When the system has high memory pressure, the page containing the
instruction may be paged out.  Using probe_kernel_address() means that
if the page is swapped out, the resulting page fault will not be
handled because page faults are disabled by this function.

Use get_user() to read the instruction instead.
Reported-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Fixes: b255188f ("ARM: fix scheduling while atomic warning in alignment handling code")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 39b65fbb ]

The pinctrl->functions[] array has pinctrl->num_functions elements and
the pinctrl->groups[] array is the same way.  These are set in
ns2_pinmux_probe().  So the > comparisons should be >= so that we don't
read one element beyond the end of the array.

Fixes: b5aa1006 ("pinctrl: ns2: add pinmux driver support for Broadcom NS2 SoC")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20190926081426.GB2332@mwandaAcked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 6b512b0e ]

The TWL4030 used on the Logit PD Torpedo SOM does not have the
keypad pins routed.  This patch disables the twl_keypad driver
to remove some splat during boot:

twl4030_keypad 48070000.i2c:twl@48:keypad: missing or malformed property linux,keymap: -22
twl4030_keypad 48070000.i2c:twl@48:keypad: Failed to build keymap
twl4030_keypad: probe of 48070000.i2c:twl@48:keypad failed with error -22
Signed-off-by: Adam Ford <aford173@gmail.com>
[tony@atomide.com: removed error time stamps]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit b1e620e7 ]

If rockchip_pcm_platform_register() fails, e.g. upon deferring to wait
for an absent DMA channel, we return without disabling RPM, which makes
subsequent re-probe attempts scream with errors about the unbalanced
enable. Don't do that.

Fixes: ebb75c0b ("ASoC: rockchip: i2s: Adjust devm usage")
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/bcb12a849a05437fb18372bc7536c649b94bdf07.1570029862.git.robin.murphy@arm.comSigned-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 3ae7359c ]

User space always expects to be able to read ALSA controls, so ensure
no kcontrols are generated without an appropriate READ flag. In the case
of a read of such a control zeros will be returned.
Signed-off-by: Stuart Henderson <stuarth@opensource.cirrus.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20191002084240.21589-1-ckeepax@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 1252b283 ]

In function pfuze100_regulator_probe(), variable "val" could be
initialized if regmap_read() fails. However, "val" is used to
decide the control flow later in the if statement, which is
potentially unsafe.
Signed-off-by: Yizhuo <yzhai003@ucr.edu>
Link: https://lore.kernel.org/r/20190929170957.14775-1-yzhai003@ucr.eduSigned-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit a315e76f ]

Implement NULL handler in set_jack function to disable
irq's.
Signed-off-by: Jaska Uimonen <jaska.uimonen@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20190927201408.925-4-pierre-louis.bossart@linux.intel.comSigned-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit f64db548 ]

ti_abb_wait_txdone() may return -ETIMEDOUT when ti_abb_check_txdone()
returns true in the latest iteration of the while loop because the timeout
value is abb->settling_time + 1. Similarly, ti_abb_clear_all_txdone() may
return -ETIMEDOUT when ti_abb_check_txdone() returns false in the latest
iteration of the while loop. Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20190929095848.21960-1-axel.lin@ingics.comSigned-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 965f6603 ]

There are total of 151 non-secure gpio (0-150) and four
pins of pinmux (91, 92, 93 and 94) are not mapped to any
gpio pin, hence update same in DT.

Fixes: 8aa428cc ("arm64: dts: Add pinctrl DT nodes for Stingray SOC")
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit ccdf3aaa ]

It turns out that sopine-baseboard needs same fix as pine64-plus
for ethernet PHY. Here too Realtek ethernet PHY chip needs additional
power on delay to properly initialize. Datasheet mentions that chip
needs 30 ms to be properly powered on and that it needs some more time
to be initialized.

Fix that by adding 100ms ramp delay to regulator responsible for
powering PHY.

Note that issue was found out and fix tested on pine64-lts, but it's
basically the same as sopine-baseboard, only layout and connectors
differ.

Fixes: bdfe4ceb ("arm64: allwinner: a64: add Ethernet PHY regulator for several boards")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 25113667 ]

Depending on kernel and bootloader configuration, it's possible that
Realtek ethernet PHY isn't powered on properly. According to the
datasheet, it needs 30ms to power up and then some more time before it
can be used.

Fix that by adding 100ms ramp delay to regulator responsible for
powering PHY.

Fixes: 94dcfdc7 ("arm64: allwinner: pine64-plus: Enable dwmac-sun8i")
Suggested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit ca234719 ]

In case of WM1811 device there are currently being registered controls
referring to registers not existing on that device.
It has been noticed when getting values of "AIF1ADC2 Volume", "AIF1DAC2
Volume" controls was failing during ALSA state restoring at boot time:
 "amixer: Mixer hw:0 load error: Device or resource busy"

Reading some registers through I2C was failing with EBUSY error and
indeed these registers were not available according to the datasheet.

To fix this controls not available on WM1811 are moved to a separate
array and registered only for WM8994 and WM8958.

There are some further differences between WM8994 and WM1811,
e.g. registers 603h, 604h, 605h, which are not covered in this patch.
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Link: https://lore.kernel.org/r/20190920130218.32690-2-s.nawrocki@samsung.comSigned-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 131cb121 ]

Currently the regulator-suspend-min/max-microvolt must be within the
root regulator node but the dt-bindings specifies it as subnode
properties for the regulator-state-[mem/disk/standby] node. The only DT
using this bindings currently is the at91-sama5d2_xplained.dts and this
DT uses it correctly. I don't know if it isn't tested but it can't work
without this fix.

Fixes: f7efad10 ("regulator: add PM suspend and resume hooks")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20190917154021.14693-3-m.felsch@pengutronix.deSigned-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 29be86d7 ]

The gcc -fcf-protection=branch option is not compatible with
-mindirect-branch=thunk-extern. The latter is used when
CONFIG_RETPOLINE is selected, and this will fail to build with
a gcc which has -fcf-protection=branch enabled by default. Adding
-fcf-protection=none when building with retpoline enabled
prevents such build failures.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 1a7f60b9 ]

This reverts commit caa8422d.

It turned out that this commit caused a regression at shutdown /
reboot, as the synchronize_irq() calls seems blocking the whole
shutdown.  Also another part of the change about shuffling the call
order looks suspicious; the azx_stop_chip() call disables the CORB /
RIRB while the others may still need the CORB/RIRB update.

Since the original commit itself was a cargo-fix, let's revert the
whole patch.

Fixes: caa8422d ("ALSA: hda: Flush interrupts on disabling")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=205333
BugLinK: https://bugs.freedesktop.org/show_bug.cgi?id=111174Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://lore.kernel.org/r/20191028081056.22010-1-tiwai@suse.deSigned-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 7d647505 ]

Commit e78a7614 ("idle: Prevent late-arriving interrupts from
disrupting offline") changes arch_cpu_idle_dead to be called with
interrupts disabled, which triggers the WARN in pnv_smp_cpu_kill_self.

Fix this by fixing up irq_happened after hard disabling, rather than
requiring there are no pending interrupts, similarly to what was done
done until commit 2525db04 ("powerpc/powernv: Simplify lazy IRQ
handling in CPU offline").

Fixes: e78a7614 ("idle: Prevent late-arriving interrupts from disrupting offline")
Reported-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Add unexpected_mask rather than checking for known bad values,
      change the WARN_ON() to a WARN_ON_ONCE()]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191022115814.22456-1-npiggin@gmail.comSigned-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit e2995b95 ]

This patch adds native DSD support for Gustard U16/X26 USB Interface.
Tested using VID and fp->dsd_raw method.
Signed-off-by: Justin Song <flyingecar@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/CA+9XP1ipsFn+r3bCBKRinQv-JrJ+EHOGBdZWZoMwxFv0R8Y1MQ@mail.gmail.comSigned-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 0067e154 ]

Oppo has issued firmware updates that change alt setting used for DSD
support. However, these devices seem to support auto-detection, so
support is moved from explicit whitelisting to auto-detection.

Also Rotel devices have USB interfaces that support DSD with
auto-detection.
Signed-off-by: Jussi Laako <jussi@sonarnerd.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit eb7505d5 ]

Add DSD support auto-detection for newer Playback Designs devices. Older
device generations have a different USB interface implementation.

Keep the auto-detection VID whitelist sorted.
Signed-off-by: Jussi Laako <jussi@sonarnerd.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit a3933186 ]

When a card is disconnected while in use, the system waits until all
opened files are closed then releases the card.  This is done via
put_device() of the card device in each device release code.

The recently reported mutex deadlock bug happens in this code path;
snd_timer_close() for the timer device deals with the global
register_mutex and it calls put_device() there.  When this timer
device is the last one, the card gets freed and it eventually calls
snd_timer_free(), which has again the protection with the global
register_mutex -- boom.

Basically put_device() call itself is race-free, so a relative simple
workaround is to move this put_device() call out of the mutex.  For
achieving that, in this patch, snd_timer_close_locked() got a new
argument to store the card device pointer in return, and each caller
invokes put_device() with the returned object after the mutex unlock.
Reported-and-tested-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 41672c0c ]

Just a minor refactoring to use the standard goto for error paths in
snd_timer_open() instead of open code.  The first mutex_lock() is
moved to the beginning of the function to make the code clearer.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>