- 16 Jun, 2009 40 commits
-
-
Jason Wessel authored
Alan Stern commented that the private driver counts must be updated regard less of the status return on the urb when the write call back is executed. This patch alters the behavior to update the private driver counts by simply moving the status check to after the driver count update. Signed-off-by:
Jason Wessel <jason.wessel@windriver.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de>
-
Jason Wessel authored
The usb_debug driver, when used as the console, will always fail to insert the carriage return and new line sequence as well as randomly drop console output. This is a result of only having the single write_urb and that the tty layer will have a lock that prevents the processing of the back to back urb requests. The solution is to allow more than one urb to be outstanding and have a slightly deeper transmit queue. The idea and some code is borrowed from the ftdi_sio usb driver. The generic usb serial driver was modified so as to allow the classic method of 1 write urb, or a multi write urb scheme with N allowed outstanding urbs where N is controlled by max_in_flight_urbs. When max_in_flight_urbs in a "struct usb_serial_driver" is non zero the multi write urb scheme will be used. The size of 4000 was selected for the usb_debug driver so that the driver lowers possibility of losing the queued console messages during the kernel startup. Signed-off-by:
-
Elina Pasheva authored
This patch fixes a problem in function sierra_indat_callback() which would stop receiving traffic from a modem if a number of URB failures occur. Failed URBs are not resubmitted for the next read and there is only a limited number of URBs allocated for the IN path. After this number of failures, the receive path stops working on a particular interface. Signed-off-by:Elina Pasheva <epasheva@sierrawireless.com>
-
Elina Pasheva authored
- Updated Copyright notice with new authors names - Version number set to 1.3.6 - Added a MAX_TRANSFER constant following Greg Kroah-Hartman's recommended setting of PAGE_SIZE-512 for USB transfer buffers and modified accordingly sierra_write() function. Signed-off-by:
-
Pete Zaitcev authored
We all know that pointless janitoring is bad, but this code is just offensive. So: - The error code goes directly to probe return, so don't return -1. - Don't return return internal usb-storage codes either. - usb_stor_control_msg takes timeout in milliseconds. - Sanitize messages. Signed-off-by:
Pete Zaitcev <zaitcev@redhat.com> Signed-off-by:
-
Randy Dunlap authored
Use "/* private:" to mark struct members as private so that scripts/kernel-doc will handle them correctly. Signed-off-by:
Randy Dunlap <randy.dunlap@oracle.com> Acked-by:
David Brownell <dbrownell@users.sourceforge.net> Signed-off-by:
-
Randy Dunlap authored
Mark internal struct members as /* private: */ so that kernel-doc won't produce warnings about missing descriptions for them. Signed-off-by:
-
Paul Mundt authored
CC drivers/usb/host/hwa-hc.o drivers/usb/host/hwa-hc.c:601: warning: initialization from incompatible pointer type drivers/usb/host/hwa-hc.c:602: warning: initialization from incompatible pointer type The prototype for these changed, so the message itself was dropped. As the only thing these hooks were doing was printing out the message for debugging, there is not much point in keeping them around. So, just kill them off. Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com> Cc: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by:
Paul Mundt <lethal@linux-sh.org> Acked-by:
David Vrabel <david.vrabel@csr.com> Signed-off-by:
-
Hermann Kneissel authored
The following patch removes the call to usb_reset_device which may occur when closing the driver by implementing a new session initialization code based on the method used by gpsbabel. The patch is against linux-2.6.30-rc3-git1. Signed-off-by: Hermann Kneissel herkne@users.sourceforge.net Signed-off-by: -
Richard Laager authored
Identify the Novatel MC760/U760/USB760 in the option USB serial driver. Signed-off-by:
Richard Laager <rlaager@wiktel.com> Signed-off-by:
-
Alan Stern authored
This patch (as1237) changes the way the PCI host controller drivers avoid retaining bogus hardware states during resume-from-hibernation. Previously we had reset the hardware as part of preparing to reinstate the memory image. But we can do better now with the new PM framework, since we know exactly which resume operations are from hibernation. The pci_resume method is changed to accept a flag indicating whether the system is resuming from hibernation. When this flag is set, the drivers will reset the hardware to get rid of any existing state. Similarly, the pci_suspend method is changed to remove the pm_message_t argument. It's no longer needed, since no special action has to be taken when preparing to reinstate the memory image. Signed-off-by:
Alan Stern <stern@rowland.harvard.edu> Acked-by:
Rafael J. Wysocki <rjw@sisk.pl> Signed-off-by:
-
Alan Stern authored
This patch (as1236) converts the USB PCI power management routines over to the new PM framework. Signed-off-by:
-
Alan Stern authored
This patch (as1235) adds an array of PCI power-state names, together with a simple inline accessor routine. Signed-off-by:
Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by:
-
Alan Stern authored
This patch (as1233) makes g_file_storage use the "unaligned" accessors. This is based on work originally done by Harvey Harrison. Signed-off-by:
Harvey Harrison <harvey.harrison@gmail.com> Acked-by:
-
Elina Pasheva authored
- Version number set to 1.3.5 - Added "\n" at the end of each string in dev_dbg() code to improve the debug information visibility. Without this change the debug logs are very difficult to read. Signed-off-by:
-
Elina Pasheva authored
- Version number set to 1.3.4 - Increased the number of input/output URBs for improved performance (numbers based on an measurement study triggered by a user request). We performed the testing using a network simulator that provided full speeds in the uplink and downlink directions and this combination of URBs provided the best throughput. Signed-off-by:
-
Greg Kroah-Hartman authored
The usb_host class isn't used for anything anymore (it was used for debug files, but they have moved to debugfs a few kernel releases ago), so let's delete it before someone accidentally puts a file in it. Signed-off-by: -
Greg Kroah-Hartman authored
The controller device is where we want this sysfs file, especially as the dev pointer is about to go away... Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: -
Greg Kroah-Hartman authored
Right now we jump through some hoops to get to the struct ohci_hcd struct in the ohci debugfs files. Remove all of the fun casting around and just use the pointer directly. This is needed as the dev pointer in the hcd structure is going away, and it makes the code simpler and smaller Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: -
Alan Stern authored
This patch (as1239) updates the kernel's treatment of Unicode. The character-set conversion routines are well behind the current state of the Unicode specification: They don't recognize the existence of code points beyond plane 0 or of surrogate pairs in the UTF-16 encoding. The old wchar_t 16-bit type is retained because it's still used in lots of places. This shouldn't cause any new problems; if a conversion now results in an invalid 16-bit code then before it must have yielded an undefined code. Difficult-to-read names like "utf_mbstowcs" are replaced with more transparent names like "utf8s_to_utf16s" and the ordering of the parameters is rationalized (buffer lengths come immediate after the pointers they refer to, and the inputs precede the outputs). Fortunately the low-level conversion routines are used in only a few places; the interfaces to the higher-level uni2char and char2uni methods have been left unchanged. Signed-off-by:
Clemens Ladisch <clemens@ladisch.de> Signed-off-by:
-
Clemens Ladisch authored
Change the encoding of strings returned by usb_string() from ISO 8859-1 to UTF-8. Signed-off-by:
-
Clemens Ladisch authored
utf8_wcstombs forgot to include one-byte UTF-8 characters when calculating the output buffer size, i.e., theoretically, it was possible to overflow the output buffer with an input string that contains enough ASCII characters. In practice, this was no problem because the only user so far (VFAT) always uses a big enough output buffer. Signed-off-by:
-
Clemens Ladisch authored
When utf8_wcstombs encounters a character that cannot be encoded, we must not decrease the remaining output buffer size because nothing has been written to the output buffer. Signed-off-by:
-
Greg Kroah-Hartman authored
People are very used to the devices file in usbfs. Now that we have moved usbfs to be an "embedded" option only, the developers miss the file, they had grown quite attached to it over all of these years. This patch brings it back and puts it in the usb debugfs directory, so that the developers don't feel sad anymore. Signed-off-by: -
Greg Kroah-Hartman authored
All usb debugfs files should be behind the usb directory, not at the root of debugfs. Signed-off-by: -
Greg Kroah-Hartman authored
All usb debugfs files should be behind the usb directory, not at the root of debugfs. Signed-off-by: -
Greg Kroah-Hartman authored
All usb debugfs files should be behind the usb directory, not at the root of debugfs. Signed-off-by: -
Greg Kroah-Hartman authored
All usb debugfs files should be behind the usb directory, not at the root of debugfs. Signed-off-by: -
Greg Kroah-Hartman authored
All usb debugfs files should be behind the usb directory, not at the root of debugfs. Signed-off-by: -
Greg Kroah-Hartman authored
Add a common usb directory in debugfs that the usb subsystem can use. Signed-off-by: -
Tony Cook authored
This patch removes all the unnecessary "\n"s that the debug print statements have, which result in everything appearing double spaced and unreadable in the logs. Signed-off-by:
Tony Cook <tony-cook@bigpond.com> Signed-off-by:
-
H Hartley Sweeten authored
Fix sparse warning in drivers/usb/core/hub.c. The following sparse warning is seen when building on ARM due do the macro raw_local_irq_save(): warning: symbol 'temp' shadows an earlier one Signed-off-by:
H Hartley Sweeten <hsweeten@visionengravers.com> Signed-off-by:
-
H Hartley Sweeten authored
Fix sparse warnings in drivers/usb/host/ohci-hcd.c. Four of the following sparse warning are seen when building on ARM due do the macro raw_local_irq_save(): warning: symbol 'temp' shadows an earlier one Signed-off-by:
-
Robert Jarzmik authored
Since the PXA 27x UDC automatically ACK's some control packets such as SET_INTERFACE, the gadgets may not get a chance to process the request before another control packet is received. The Linux gadgets do not expect to receive setup callbacks out of order. The file storage gadget only saves the "highest" priority request. The PXA27x UDC driver must make sure it only sends one up at a time, allowing the gadget to make changes before continuing. In theory, the host would be NACK'd while the gadget processes the change but the UDC has already ACK'd the request. If another request is sent by the host that is not automatically ACK'd by the UDC, then the throttling happens properly to regain sync. The observed case was the file_storage gadget timing out on a BulkReset request because the SET_INTERFACE was being processed by the gadget. Since SET_INTERFACE is higher priority than BulkReset, the BulkReset was dropped. This was exacerbated by turning on the debug which delayed the fsg signal processing thread. This also fixes the "should never get in WAIT_ACK_SET_CONF_INTERF state here!!!" warning. Reported-by:
Vernon Sauder <vernoninhand@gmail.com> Signed-off-by:
Robert Jarzmik <robert.jarzmik@free.fr> Acked-by:
-
Robert Jarzmik authored
Got pxa27x_udc working on the pxa320 Nomad platform. The problem was that the pxa3xx UDC is not quite compatible with the pxa27x UDC in how it handles back-to-back control packets. The pxa27x probably drops them by default, but the pxa320 does not, and you have to detect it and set the OPC bit to clear the zero-length packet. Signed-off-by:
Aric Blumer <aric@sdgsystems.com> Signed-off-by:
-
David Brownell authored
Follow pxa27x change in OTGPH handling, and use the newly defined pxa27x_clear_otgph(). Signed-off-by:
Eric Miao <eric.miao@marvell.com> Acked-by:
-
Matthias Kaehlcke authored
use usb_endpoint_type() instead of fiddling manually with bmAttributes Signed-off-by:
Matthias Kaehlcke <matthias@kaehlcke.net> Acked-by:
-
Matthias Kaehlcke authored
Use helper functions to determine the type and direction of an endpoint instead of fiddling with bEndpointAddress and bmAttributes Signed-off-by:
-
Matthias Kaehlcke authored
Use helper functions to determine the type and direction of an endpoint instead of fiddling with bEndpointAddress and bmAttributes Signed-off-by:
-
Matthias Kaehlcke authored
Use helper functions to determine the type and direction of an endpoint instead of fiddling with bEndpointAddress and bmAttributes Signed-off-by:
-
