The Tx DMA unit should be disabled when bringing the device down.  Also,
the KX4 device with 82599 supports WoL, so we should clear the Wake Up
Status (WUS) after a PCIe slot reset.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are possible times that a driver may fail to completely initialize,
due to a buggy platform or a buggy kernel.  In those cases, we'd rather
fail gracefully instead of a panic.  Add a few safety checks to some
critical paths to try and prevent a panic in these corner-case situations.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This cleans up the following pieces of the Rx initialization path:

- Enable the ECC memory fault interrupt in OTHER causes.

- Fix an 82598 initialization of RDRXCTL when depending on RSS and VMDq to
be enabled.  We don't need these features enabled to safely set the MVMEN
bit to allow multiple SRRCTL register mappings into the RXDCTL registers.

- Fix the RSS initialization path to not stomp on DCB accidentally.  When
configuring the MRQC (multiple Rx queue contol) register, we want to make
sure we only OR in features as necessary, instead of full assignment.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Tx accounting when cleaning during NAPI was not completely properly.
We should use the work_limit to determine when to finish cleaning, and
use the same to return the cleaned status.  The impact of running like this
causes the NAPI clean for this Tx to get stuck in a scheduling loop, and
can result in Tx not getting cleaned, ending with a Tx hang and device
reset.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Occasionally if the driver was loaded in a system that
didn't support MSI-X or MSI and was on a shared interrupt,
the driver would then panic in NAPI on the first shared
interrupt because we hadn't called napi_add yet.

Solution: call napi_add before calling request_irq
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The interrupt models using EITR have changed in 82599.  The way the register
is laid out, the change is transparent to some of the existing code.
However, some of it isn't.  This patch fixes all the cases where EITR
handling is different than 82598.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

82599 mistakenly enabled drop on Rx queues in the packet buffer.  The
default mode should be store-and-forward from the FIFO.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The rx_no_dma_resources counter reported by ethtool -S ethX is not
counting correctly.  In 82599, the queue mappings for the counters need
to be mapped properly, and accounted for properly.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Acked-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A purely cosmetic change.  Report which physical layer is present, instead
of PHY unknown.  82599 added new PHY types for the SFP+ devices, and this
was missed getting updated.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for 82576 copper adapter and necessary code to restrict wol for
quad port adapter to first port.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adding device id to support 82576NS dual port copper
NIC.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch corrects a typo that was doing a less than comparison instead of
a left shift due to the fact that I didn't get enough <'s in there.

This resolves an issue in which vlans were not functioning correctly.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add Pf to pool if adding a VLVF register value and the VFTA bit is
already set.

This patch addresses the unlikely situation that the PF adds a vlan
entry when the vlvf is full, and a vf later adds the vlan to the vlvf.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We need to support wol on the second port for situations such as when the
lan ports are on the motherboard itself.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If DCA is undefined then the adapter struct becomes unnecessary.  To
resolve this issue the DCA calls can simply make a call to the adapter
struct through the rx_ring adapter struct member.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The netif_running check in igb poll is a hold over from the use of fake
netdevs to use multiple queues with NAPI prior to 2.6.24.  It is no longer
necessary to have the call there and it currently can cause errors if
work_done == budget.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With the new DCA API, the driver should use dca3_get_tag() instead of
the obsolete dca_get_tag().

Signed-off-by: Maciej Sosnowski < maciej.sosnowski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I found the PPP subsystem to not work properly when connecting channels
with different speeds to the same bundle.

Problem Description:

As the "ppp_mp_explode" function fragments the sk_buff buffer evenly
among the PPP channels that are connected to a certain PPP unit to
make up a bundle, if we are transmitting using an upper layer protocol
that requires an Ack before sending the next packet (like TCP/IP for
example), we will have a bandwidth bottleneck on the slowest channel
of the bundle.

Let's clarify by an example. Let's consider a scenario where we have
two PPP links making up a bundle: a slow link (10KB/sec) and a fast
link (1000KB/sec) working at the best (full bandwidth). On the top we
have a TCP/IP stack sending a 1000 Bytes sk_buff buffer down to the
PPP subsystem. The "ppp_mp_explode" function will divide the buffer in
two fragments of 500B each (we are neglecting all the headers, crc,
flags etc?.). Before the TCP/IP stack sends out the next buffer, it
will have to wait for the ACK response from the remote peer, so it
will have to wait for both fragments to have been sent over the two
PPP links, received by the remote peer and reconstructed. The
resulting behaviour is that, rather than having a bundle working
@1010KB/sec (the sum of the channels bandwidths), we'll have a bundle
working @20KB/sec (the double of the slowest channels bandwidth).


Problem Solution:

The problem has been solved by redesigning the "ppp_mp_explode"
function in such a way to make it split the sk_buff buffer according
to the speeds of the underlying PPP channels (the speeds of the serial
interfaces respectively attached to the PPP channels). Referring to
the above example, the redesigned "ppp_mp_explode" function will now
divide the 1000 Bytes buffer into two fragments whose sizes are set
according to the speeds of the channels where they are going to be
sent on (e.g .  10 Byets on 10KB/sec channel and 990 Bytes on
1000KB/sec channel).  The reworked function grants the same
performances of the original one in optimal working conditions (i.e. a
bundle made up of PPP links all working at the same speed), while
greatly improving performances on the bundles made up of channels
working at different speeds.
Signed-off-by: Gabriele Paoloni <gabriele.paoloni@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

promote 'cnt' to size_t, to match 'len'.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

skb->len is an unsigned int, so the test in x25_rx_call_request() always
evaluates to true.

len in x25_sendmsg() is unsigned as well. so -ERRORS returned by x25_output()
are not noticed.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Windows (XP at least) hosts on boot, with configured static ip, performing 
address conflict detection, which is defined in RFC3927.
Here is quote of important information:

"
An ARP announcement is identical to the ARP Probe described above, 
except    that now the sender and target IP addresses are both set 
to the host's newly selected IPv4 address. 
"

But it same time this goes wrong with RFC5227.
"
The 'sender IP address' field MUST be set to all zeroes; this is to avoid
polluting ARP caches in other hosts on the same link in the case
where the address turns out to be already in use by another host.
"

When ARP proxy configured, it must not answer to both cases, because 
it is address conflict verification in any case. For Windows it is just 
causing to detect false "ip conflict". Already there is code for RFC5227, so 
just trivially we just check also if source ip == target ip.
Signed-off-by: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: David S. Miller <davem@davemloft.net>

The original patch was submitted last year but wasn't discussed or applied
because of missing maintainer's CCs. I only fixed some formatting errors,
but as I saw tulip is very badly formatted and needs further work.

Original description:
This patch fixes MTU problem, which occurs when using 802.1q VLANs. We
should allow receiving frames of up to 1518 bytes in length, instead of
1514.

Based on patch written by Ben McKeegan for 2.4.x kernels. It is archived
at http://www.candelatech.com/~greear/vlan/howto.html#tulip
I've adjusted a few things to make it apply on 2.6.x kernels.

Tested on D-Link DFE-570TX quad-fastethernet card.
Signed-off-by: Tomasz Lemiech <szpajder@staszic.waw.pl>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Ben McKeegan <ben@netservers.co.uk>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

It closes a race in phy_stop_machine when reprogramming of phy_timer
(from phy_state_machine) happens between del_timer_sync and cancel_work_sync.

Without this change it could lead to crash if phy_device would be freed after
phy_stop_machine (timer would fire and schedule freed work).
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

From: Pavel Roskin <proski@gnu.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes the circular locking problem by changing the locking strategy
concerning the logging of firmware handles.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Changing the mac address when a macvlan device is up will leave the
device on the wrong hash chain making it impossible to receive
packets.

There is no checking of the mac address set on the macvlan.  Allowing
a misconfiguration to grab packets from the the underlying device or
another macvlan.

To resolve these problems I update the hash table of macvlans when the
mac address of a macvlan changes, and when updating the hash table
I verify that the new mac address is usable.

The result is well defined and predictable if not perfect handling of
mac vlan mac addresses.

To keep the code clear I have created a set of hash table maintenance
in macvlan so I am not open coding the hash function and the logic
needed to update the hash table all over the place.
Signed-off-by: Eric Biederman <ebiederm@aristanetworks.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

When running in a network namespace whose only link to
the outside world is a macvlan device, not being
able to create another macvlan is a real pain.

So modify macvlan creation to allow automatically forward
a creation of a macvlan on a macvlan to become a creation
of a macvlan on the underlying network device.
Signed-off-by: Eric Biederman <ebiederm@aristanetworks.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch from Juha Leppanen suppresses a false warning if the eeprom
load succeeds on the very last attempt.

Juha> In function smsc911x_open smsc911x_reg_read+udelay can be run 50
Juha> times with timeout reaching -1, and the following if statetement
Juha> does not catch the timeout and no warning is issued. Also if the
Juha> 50th smsc911x_reg_read is GOOD, loop is exited with timeout as 0
Juha> and bogus warning issued.  Replace testing order and --timeout
Juha> instead of timeout-- and now max 50 smsc911x_reg_read's are done,
Juha> with max 49 udelays.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch from Juha Leppanen suppresses a false warning if a fast
forward operation succeeds on the very last attempt.

Juha> If smsc911x_reg_read loop is executed 500 times, timeout reaches 0
Juha> and the 500th smsc911x_reg_read result in val is ignored. If
Juha> testing order is changed, then val is checked first. The 500th
Juha> reg_read might be GOOD, why ignore it!
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Network Drop Monitor: Adding Build changes to enable drop monitor
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>

 include/linux/Kbuild |    1 +
 net/Kconfig          |   11 +++++++++++
 net/core/Makefile    |    1 +
 3 files changed, 13 insertions(+)
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>

 include/linux/net_dropmon.h |   56 +++++++++
 net/core/drop_monitor.c     |  263 ++++++++++++++++++++++++++++++++++++++++++++
 2 files changed, 319 insertions(+)
Signed-off-by: David S. Miller <davem@davemloft.net>

Network Drop Monitor: Adding kfree_skb_clean for non-drops and modifying end-of-line points for skbs
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>

 include/linux/skbuff.h |    4 +++-
 net/core/datagram.c    |    2 +-
 net/core/skbuff.c      |   22 ++++++++++++++++++++++
 net/ipv4/arp.c         |    2 +-
 net/ipv4/udp.c         |    2 +-
 net/packet/af_packet.c |    2 +-
 6 files changed, 29 insertions(+), 5 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>

 include/trace/skb.h   |    8 ++++++++
 net/core/Makefile     |    2 ++
 net/core/net-traces.c |   29 +++++++++++++++++++++++++++++
 3 files changed, 39 insertions(+)
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 1577ecef
Author: Andy Fleming <afleming@freescale.com>
Date:   Wed Feb 4 16:42:12 2009 -0800

    netdev: Merge UCC and gianfar MDIO bus drivers

left out the deletion of gianfar_mii.c.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Similar patch as for 8139cp posted yesterday, so the same comment:

So far there was not a chance to set a mac address on running 8139too device.
This is for example needed when you want to use this NIC as a bonding slave in
bonding device in mode balance-alb. This simple patch allows it.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

So far there was not a chance to set a mac address on running 8139cp device.
This is for example needed when you want to use this NIC as a bonding slave in
bonding device in mode balance-alb. This simple patch allows it.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RFC5061 states:

        Each adaptation layer that is defined that wishes
        to use this parameter MUST specify an adaptation code point in an
        appropriate RFC defining its use and meaning.

If the user has not set one - assume they don't want to sent the param
with a zero Adaptation Code Point.

Rationale - Currently the IANA defines zero as reserved - and
1 as the only valid value - so we consider zero to be unset - to save
adding a boolean to the socket structure.

Including this parameter unconditionally causes endpoints that do not
understand it to report errors unnecessarily.
Signed-off-by: Malcolm Lashley <mlashley@gmail.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RFC3758 Section 3.3.1.  Sending Forward-TSN-Supported param in INIT

   Note that if the endpoint chooses NOT to include the parameter, then
   at no time during the life of the association can it send or process
   a FORWARD TSN.

If peer does not support PR-SCTP capable, don't send FORWARD-TSN chunk
to peer.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fix to indicate ASCONF support in INIT-ACK only if peer has
such capable.

This patch also fix to calc the chunk size if peer has no FWD-TSN
capable.
Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com>
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>